Aiphone AXW-AVT, AXW-AVR User Manual

0311

AX Series Audio-Video Adaptor for 3rdParty Transmission Equipment

- INSTRUCTIONS -

The AXW-AVT and AXW-AVR are designed to allow connection of a standard AX-series audio video door station (or audio-only IE-series door station) via the AXW-AVT, conditioning the signal for use with 3

party transmission equipment (fiber optics, Ethernet, etc.) and converting it back via the AXW-AVR to a signal compatible with the AX-series exchange unit. External video input/output is provided at both adaptors to allow 3

party camera input, output to recording devices, etc. A motion detector or other activation device can be connected to the Sensor input to trigger door / camera activation (AXW-AVT only). The units also feature a relay output to trigger an external device, such as a DVR or video switcher local to either the AXWAVT or AXW-AVR whenever the audio and/or video is active. Alternatively, the AXW-AVT can be used to adapt an AX-series audio video door station to a standalone third party device (video server, network DVR, etc).

AXW-AVT

OUT IN

VIDEO

CCTV DOOR

DOOR

AUDIO

IN OUT

+ -

+ - + -

+ -

CALL

+ -

SENSOR

NC NC

RELAY

NO NO

24VOUT

AXW-AVT

AXW-AVT TERMINAL DEFINITIONS:

DOOR (RJ-45 Jack): RJ-45 connection from AX-series audio video door, or spliced audio only door (IE/

IF-series).

AUDIO IN/OUT: Input / Output connections for audio transmission (line level, polarity indicated by

‘+’ and ‘-’).

CALL IN/OUT: Transistor-switched input / output to be connected to relay input / output on

transmission equipment. ‘Call In’ indicates call placed by door station, ‘Call Out’ indicates master-initiated activity (polarity indicated by ‘+’ and ‘-’).

SENSOR NC, NC: Normally Closed contact input, activates ‘Call In’ function when tripped by external

motion detector or other device with N/C contacts. RELAY NO, NO: Normally Open relay contact, activated whenever communication is active. VIDEO IN: Composite input signal from CCTV camera, if used in place of AX-series audio

video door station. VIDEO OUT: Composite output to external transmission equipment. Source dependent upon

CCTV / DOOR switch. CCTV / DOOR SWITCH: Determines whether AX-series audio/video door station video (‘DOOR’ setting) or

external CCTV video (‘CCTV’ setting) will be present on ‘VIDEO OUT’ for

connection to external transmission equipment. 24V +, - 24V DC input (use Aiphone PS-2420UL).

Pg. 1

AXW-AVR

OUT IN

RELAY

NO NO

OUT

+ -

CALL

+ -

AUDIO

INOUT

+ -

CEU

75 OHM

VIDEO

OFF ON

AXW-AVR

AXW-AVR TERMINAL DEFINITIONS:

RELAY NO, NO: Normally Open relay contact, activated whenever communication is active. CALL IN/OUT: Transistor-switched input / output to be connected to relay input / output on

transmission equipment. ‘Call In’ indicates call placed by door station, ‘Call Out’ indicates master-initiated activity (polarity of input / output indicated by ‘+’ and ‘-’).

AUDIO IN/OUT: Input / Output connections for audio transmission (line level, polarity indicated by

‘+’ and ‘-’).

VIDEO IN: Composite input signal from CCTV camera, if used in place of AX-series audio

video door station.

VIDEO OUT: Composite output to external transmission equipment. Source dependent upon

CCTV / DOOR switch.

OFF/ON SWITCH: Determines whether AX-series audio video door station video (‘DOOR’ setting) or

external CCTV video (‘CCTV’ setting) will be present on ‘VIDEO OUT’ for connection to external transmission equipment.

CEU (RJ-45 Jack): RJ-45 connection from AXW-AVR to CEU, simulating a standard AX-series Audio/

Video door station.

COMPATIBLE DOOR STATIONS (AXW-AVT):

AX-DV Surface mount, die cast zinc, vandal resistant, Audio-Video AX-DVF Flush mount, stainless steel, vandal resistant, Audio-Video AX-DM Mullion mount, black plastic, Audio Only IF-DA Surface mount, brown plastic, Audio Only IE-DC Surface mount, brown plastic w/aluminum, Audio Only IE-JA Flush mount, 2 gang, stainless steel faceplate, Audio Only IE-SS Flush mount, 2-gang, stainless steel, vandal resistant, Audio Only IE-SSR Flush mount, 2-gang, stainless steel, vandal resistant w/red mushroom call button, Audio Only

PROGRAMMING:

1. Follow standard AX programming procedures as described in the AX Installation & Operation manual (included on CD with the AX CEU).

2. When configuring door stations, be sure to set the station number corresponding to the AXW-AVT / AVR to “Video” in the AX setup utility.

Typical configuration selection

Pg. 2

CONFIGURATION DIAGRAM: AXW-AVT / AXW-AVR with Meridian Technology Fiber (ST/SR-AiphoneAX1-XS), 1 of 2

AX-DM or IE/IF-Series

Audio Door Station

CCTV Camera 75 Ohm, 1V Peak-to-peak (Independently powered)

AXW-AVT

24V

RELAY

NO NO

SENSOR

NC NC

CALL IN

CALL OUT

AUDIO IN

AUDIO OUT

DOOR

PS-2420UL

Normally Open contact for remote device activation

(i.e. video switcher, DVR, etc.)

Normally Closed input for remote activation

(i.e. motion sensor, loop detector, etc.)

AX-DV

CAT-5e

Coax

Configuration Notes (1 of 2):

1. AX-series video door station connects to ‘DOOR’ input of AXW-AVT.

Ensure that the “CCTV / DOOR’ switch on the AXW-AVT is in the ‘DOOR’ position.

*2. Alternatively, an IE/IF-series or AX-DM audio door may be used, along

with 3

party CCTV camera. Connect audio door station to ‘Door’ input (following the wiring method shown in the AX-series installation manual, pg. 12). Connect the camera to ‘Video In’ and put the ‘CCTV / DOOR’ switch in the ‘CCTV’ position.

3. Connect the Call In / Call Out and Audio In / Audio Out connections on the AXW-AVT to the Meridian fiber transmitter module (as detailed at right, Fig. 1). For complete pin definitions, consult the Meridian installation document.

VIDEO IN

VIDEO OUT

Coaxial Video Cable

To Door Release

Configuration Notes (1 of 2, continued):

4. When the SENSOR input is used, the door station will be turned on whenever the sensor device is activated (Normally Closed contact from 3rdparty supplied device).

5. The RELAY output provides an optional Normally Open dry contact output which is activated whenever the AX-series door station is in use. This can be used to activate any device local to the AXW-AVT (DVR trigger, video switcher activation, local call indication, etc.).

6. Configure AXW-AVT internal jumpers as necessary (see Pg. 21).

Meridian

ST-AiphoneAX1-XS

PWR DIAG TX C/L RX C/E

SYN VID

DR1 DR2 AR1 AR2 CR1 CR2 DT1 DT2 AT1 AT2 CT1 CT2

OPTICAL

VIDEO

RX TX

(to SR-AiphoneAX1-XS, Pg. 5)

DATAC.C.AUDIO

Optic Fiber

Connection details from AXW-AVT to ST-AiphoneAX1-XS ‘Audio’ Connector Detail:

Pin 1 Audio In Pin 2 Audio In + Pin 3 Audio Out Pin 4 Audio Out +

‘C.C.’ Connector Detail:

Pin 1 Call Out Pin 2 Call Out + Pin 3 Call In + Pin 4 Call In -

‘DATA’ Connector Detail:

Pin 1 & 2 Optional Door

release contact output

Fig. 1

Pg. 3

Please Note:

Only information pertaining to the connection and operation of the AXW-AVT / AXW-AVR and listed 3 responsible for attempts to connect the AXW-AVT / AXW-AVR to untested 3

party transmission hardware. Consult the installation manual for the 3rdparty device being utilized

party devices interfacing with it are included here. Aiphone is not

for further information regarding physical mounting, base functionality, power requirements, etc. For the most up-to-date compatibility information, please consult http:// www.aiphone.com or contact Aiphone Technical Support.

For complete AX system installation, wiring, and programming information, please consult the AX Installation Manual (included on CD with AX Central Exchange Unit, or available at http://www.aiphone.com).

Pg. 4

CONFIGURATION DIAGRAM: AXW-AVT / AXW-AVR with Meridian Technology Fiber (ST/SR-AiphoneAX1-XS), 2 of 2

Configuration Notes (2 of 2):

1. Connect the AXW-AVR ‘CEU’ connection to an unused Door station input on the AX-CEU and ensure that the AX-CEU has been programmed to accept a video door station on that input (see Pg. 2).

2. Connect the Call In / Call Out and Audio In / Audio Out connections on the AXW-AVR to the Meridian fiber receiver module (as detailed below, Fig. 2). For complete pin definitions, consult the Meridian installation document.

3. The RELAY output on the AXW-AVR provides a Normally Open dry contact output whenever the door station connection is active. This can be used to activate any device local to the AXW-AVT (DVR trigger, video switcher activation, local call indication, etc.).

Meridian

SR-AiphoneAX1-XS

(to ST-AiphoneAX1-XS, Pg. 4)

Optic Fiber

AXW-AVT to SR-AiphoneAX1-XS ‘Audio’ Connector Detail:

Pin 1 Audio In Pin 2 Audio In + Pin 3 Audio Out Pin 4 Audio Out +

‘C.C.’ Connector Detail:

Pin 1 Call Out Pin 2 Call Out + Pin 3 Call In + Pin 4 Call In -

‘DATA’ Connector Detail:

Pin 3 & 4 Optional Door

release contact input (from CEU)

Fig. 2

PWR DIAG TX C/L RX C/E

SYN VID

DR1 DR2 AR1 AR2 CR1 CR2 DT1 DT2 AT1 AT2 CT1 CT2

OPTICAL

VIDEO

RX TX

Coaxial Video Cable

Application Considerations:

The Meridian fiber modules shown include extra contact closures which may be used for door release output local to the door station (using dry contact output of the AX-CEU as a trigger)

DATAC.C.AUDIO

From AX CEU Door

Release Output

Power supply connections to the Meridian fiber modules are not shown, and are dictated by the mounting method chosen (standalone, rack mount, etc). Contact Meridian Technologies for available options. AXW-AVT / AXW-AVR should be mounted as close as possible to their corresponding Meridian fiber modules. Avoid mounting units near high voltage AC devices, or other sources of inductive noise.

AXW-AVR

CEU

AUDIO IN

AUDIO OUT

CALL IN

CALL OUT

RELAY

NO NO

VIDEO IN

VIDEO OUT

To AX-CEU (Door Input)

Normally Open contact for remote device activation

(i.e. video switcher, DVR, etc.)

Composite Video Output*

(for CCTV monitor, DVR, etc.)

Please Note:

Only information pertaining to the connection and operation of the AXW-AVT / AXW-AVR and listed 3

party devices interfacing with it are included here. Aiphone is not responsible for attempts to connect the AXW-AVT / AXW-AVR to untested 3rdparty transmission hardware. Consult the installation manual for the 3rdparty device being utilized for further information regarding physical mounting, base functionality, power requirements, etc. For the most up-to-date compatibility information, please consult http:// www.aiphone.com or contact Aiphone Technical Support.

For complete AX system installation, wiring, and programming information, please consult the AX Installation Manual (included on CD with AX Central Exchange Unit, or

Pg. 5 Pg. 6

available at http://www.aiphone.com).

+ 9 hidden pages