AgriFab 45-05302 Quick Start Guide
Quick Start Guide
7
1
E
F
F
45-05302 Tow Spreader
Read the manual that came with your Tow Spreader for:
• Important safety warnings
• Further explanation of features
• Operating instructions
Problem?
Call 1-800-448-9282
Quick Start Guide
45-05302 Tow Spreader
Read the manual that came with your Tow Spreader for:
• Important safety warnings
• Further explanation of features
• Operating instructions
Problem?
Call 1-800-448-9282
HARDWARE PACKAGE
A
x10
B
x1
1509-69
45165
E
x3
49449
H
x2
D
x2
C
x2
F
x2
45705
43088
I
x1
47963
NOTE: Left and Right are determined by the
driver's seated position on the tractor.
STEP 1 (SEE FIGURE 1): Attach the ow plate (9)
to the hopper as shown in gure 1.
9
1
STEP 3 (SEE FIGURE 3): Loosely attach the
frame tubes (7) to the crossover brace (10) using
four 1/4 x 1-3/4" hex bolts (A) and 1/4" nylock
nuts (K). Do Not Tighten! Insert the long end of
the axle through the right side of the frame tube
assembly and then insert the at end through the
left side of the frame assembly as shown.
RIGHT
STEP 5 (SEE FIGURE 5): Attach the hopper (1) to
the frame assembly using two 1/4 x 1-3/4" hex bolts
(A) and 1/4" nylock nuts (K). Insert the hairpin
agitator (L) into the impeller shaft making sure that
it is secured in place and horizontal.
1
A
L
D
G
x1
L
x1
43343
K
x11
J
x4
47189
44101
R19171616
48934
47623
Figure 1
STEP 2 (SEE FIGURE 2): Attach the control cable
(4) to the hopper (1) by inserting the end of the
cable through the hold in the ow plate (9) and
pressing the plastic anchor rmly into the slot in the
hopper until it locks into place.
4
LEFT
0
STEP 4 (SEE FIGURE 4): Insert a tube plug (E)
into the end of each frame tube. Slide a ange
bearing (F) over each end of the axle and secure
K
8
into the frame tubes. Make sure the gearbox is
centered and the impeller shaft is vertical.
7
K
Figure 3
E
Figure 5
Figure 2
Figure 4
FORM NO. 45936 (10/30/19)
Read the manual that came with your Tow Spreader for:
E
K
B
G
J
5
C
H
J
H
H
6
Quick Start Guide
45-05302 Tow Spreader
• Important safety warnings
• Further explanation of features
• Operating instructions
STEP 6 (SEE FIGURE 6): Slide a washer (J), a
spacer (C), a drive wheel (6), and another washer
onto the at end of the axle . Secure with a cotter
pin (H) by sliding it through the hole in the axle and
bending the ends.
J
C
J
Problem?
Call 1-800-448-9282
STEP 8 (SEE FIGURE 8): Attach the control tube
(2) and the hitch tube (3) to the assembly using
two 1/4 x 1-3/4" hex bolts (A) and nylock nuts (K).
Quick Start Guide
45-05302 Tow Spreader
STEP 10 (SEE FIGURE 10): Attach the hitch
brackets to the hitch tube using two 1/4 x 1-3/4"
hex bolts (A) and nylock nuts (K). Insert the hitch
pin (I) through the hitch brackets and secure with a
hair cotter pin (G).
Read the manual that came with your Tow Spreader for:
• Important safety warnings
• Further explanation of features
• Operating instructions
Problem?
Call 1-800-448-9282
Figure 6
STEP 7 (SEE FIGURE 7): Attach the other wheel
by sliding onto the right end of the axle a washer
(J), a spacer (C), a wheel (5), and another washer.
Secure with a cotter pin (H) by sliding it through the
hole in the axle and bending the ends.
A
A
I
2
K
STEP 9 (SEE FIGURE 9): Attach the control cable
Figure 10
to the control tube using a 1/4 x 2" carriage bolt (B)
and 1/4" nylock nut (K). Insert a tube plug (E) into
the end of the control tube.
K
3
Figure 8
Figure 7
Figure 9
Loading...