Page 1
Agri-Fab
OWNERS
MANUAL
Model No.
45-0355-131
¨
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
3 PT. HITCH
TANG CULTIVATOR
• Safety
• Assembly
• Operation
• Maintenance
• Parts
the fastest way to purchase parts
www.speedepart.com
PRINTED IN USA FORM NO. 49358 (4/04)
Page 2
SAFETY RULES
Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to
operate the equipment. Exercise caution at all times when using power equipment.
LOOK FOR THIS SYMBOL TO POINT OUT
IMPORTANT SAFETY PRECAUTIONS. IT
MEANS – ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED.
1. Read this owner's manual before using this equipment.
2. Do not allow children to operate the tow vehicle or the
tine cultivator.
3. Do not allow adults to operate the tow vehicle or the
tine cultivator without proper instruction.
4. Do not allow anyone to ride on the tow vehicle or the
tine cultivator.
5. Before lowering the tine cultivator, make sure no one
is near the area of operation.
6. Lower the tine cultivator when leaving the tow
vehicle unattended.
CARTON CONTENTS
1. Cross Brace
2. Depth Gauge Bar (2)
3. Weight Bracket
4. Mast Extension Strap (2)
5. Mast Side (2)
6. Mast Lift Strap (2)
7. Support Bracket
8. Cultivator Assembly
Parts Package (see page 3)
CAUTION: VEHICLE BRAKING AND
STABILITY MAY BE AFFECTED BY THE
ADDITION OF AN ACCESSORY OR AN
ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES.
7. Wear appropriate footwear when using the tine cultivator. The tip of each tang on the cultivator is pointed
and sharp!
8. Tow vehicle braking and stability may be affected by
the tine cultivator. Drive slowly with the tine cultivator
in the transport position. Stay off steep slopes.
9. Stop and inspect the equipment for damage after
striking an object. Repair any damage before continuing operation.
10. Keep all nuts and bolts tight and be sure that the
equipment is in safe operating condition.
11. Before attaching or removing the tine cultivator, park
and lock the tow vehicle in a safe condition.
2
1
3
5
7
6
4
8
2
Page 3
D
E
B
A
C
I
J
F
H
K
L
G
M
N
PARTS PACKAGE CONTENTS – PARTS SHOWN ACTUAL SIZE
KEY QTY. DESCRIPTION
A 2 Category 1 Pin
B 1 Pivot Pin
C 1 Haircotter Pin, 1/8"
D 2 Hex Bolt, 3/8" x 2-1/4" Lg.
E 2 Hex Bolt, 1/2" x 1-1/2" Lg.
F 2 Hex Bolt, 1/2" x 2-3/4" Lg.
G 1 Hex Bolt, 1/2" x 3-1/2" Lg.
KEY QTY. DESCRIPTION
H 2 Hex Bolt, 3/8" x 1" Lg.
I 8 Hex Nut, Nylock, 3/8"
J 2 U-Bolt, 3/8"
K 5 Hex Nut, Nylock, 1/2"
L 1 Spacer
M 2 Lock Washer, 7/8"
N 2 Hex Nut, 7/8"
3
Page 4
ASSEMBLY
TOOLS REQUIRED FOR ASSEMBLY
(2) 3/4" Wrenches
(2) 9/16" Wrenches
(2) 1-1/8" Wrenches or Adjustable Wrenches
(1) 1-5/16" Wrench or 12" Adjustable Wrench
CAUTION: THE CULTIVATOR TANGS
HAVE SHARP POINTS. USE CARE
WHEN HANDLING AND ASSEMBLING
THE TANGS. WEAR GLOVES FOR
EXTRA PROTECTION AGAINST CUTS.
Remove all loose parts and the hardware package
from the shipping carton. Lay out and identify each
part and the hardware as shown on pages 2 and 3. Be
sure the carton is empty before it is discarded.
1. Attach two depth gauge bars to the frame using a
3/8" U-bolt and two 3/8" Nylock hex nuts for each
bar. Put each depth gauge bar next to each outside tang on the rear of the frame as shown in
figure 1. Use the holes in each bar that will give the
desired working depth, if known at this time. Use
matching holes in both depth gauge bars to keep
the cultivator level.
NOTE: For effective depth control a depth gauge bar
must not be located directly behind a front tang.
DEPTH
GAUGE
BAR
2. Attach two mast extension straps to the front of
the frame using two 1/2" x 2-3/4" hex bolts and two
1/2" Nylock hex nuts. Point the bent end of each
strap toward the outside of the frame. Do not
tighten yet. See figure 2.
1/2" NYLOCK
HEX NUT
1/2" x 2-3/4"
HEX BOLT
FRONT
MAST EXTENSION
STRAP (RIGHT
SIDE)
FIGURE 2
3. Attach the cross brace and the two mast sides to
the ends of the mast extension straps. The cross
brace is between the extension straps while the
mast sides are on the outside. The cross brace
and mast sides are connected to the extension
straps using two category 1 pins, two 7/8" lock
washers, and two 7/8" hex nuts. Do not tighten
yet. See figure 3.
7/8" LOCK WASHER
7/8" HEX
NUT
3/8"
U-BOLT
FIGURE 1
DEPTH
GAUGE BAR
WORKING
DEPTH
3/8" NYLOCK
HEX NUT
FIGURE 3
4
CROSS
BRACE
CATEGORY
1 PIN
EXTENSION
STRAP
MAST
SIDE
Page 5
4. Arrange the mast lift straps as shown in figure 4.
Place the straps and the spacer between the mast
sides, fastening them to the lower hole in the mast
sides using a 1/2" x 3-1/2" hex bolt and 1/2" Nylock
hex nut. Do not tighten yet.
6. Attach the lower end of each mast lift strap to the
outside of the welded frame braces and attach the
support bracket to the inside of the frame braces.
Use two 1/2" x 1-1/2" hex bolts and two 1/2"
Nylock hex nuts. Do not tighten yet. See figure 6.
SPACER
1/2" NYLOCK
HEX NUT
1/2" x 3-1/2"
HEX BOLT
MAST
SIDE
MAST LIFT
STRAP
FIGURE 4
5. Install the pivot pin through the upper hole at the
end of the mast sides. Secure the pivot pin with a
1/8" hair cotter pin. See figure 5.
SUPPORT
BRACKET
1/2" NYLOCK
HEX NUT
MAST LIFT
STRAP
FRAME
BRACES
1/2" x 1-1/2"
HEX BOLT
FIGURE 6
7. Attach the front of the weight bracket to the support bracket using two 3/8" x 1" hex bolts and two
3/8" Nylock hex nuts. Attach the sides of the
weight bracket to the rear of the frame using two
3/8" x 2-1/4" hex bolts and two 3/8" Nylock hex
nuts. See figure 7.
PIVOT PIN
FIGURE 5
1/8" HAIR
COTTER PIN
8. Tighten all loose bolts and nuts at this time.
3/8" x 1"
HEX BOLT
3/8" x 2-1/4"
HEX BOLT
3/8" NYLOCK
HEX NUT
WEIGHT
BRACKET
3/8" NYLOCK
HEX NUT
FIGURE 7
5
Page 6
OPERATION
CAUTION: USE CARE WHEN WORKING
AROUND A RAISED CULTIVATOR. KEEP
YOUR FEET AND HANDS FROM UNDER
THE TANGS AT ALL TIMES. SERIOUS
INJURY CAN RESULT SHOULD THE
CULTIVATOR DROP UNEXPECTEDLY.
The tine cultivator is used to loosen soil and other
types of landscape material.
1. Before starting, make sure the material to be
cultivated, such as dirt, is dry enough by squeezing some in your hand. If it forms a ball that doesn't
crumble, the material may be too wet to cultivate.
2. The cultivator can be set for various depths of
cultivation. To change the cultivation depth, raise
or lower the two depth gauge bars located on the
back of the frame assembly as shown in figure 8.
ADJUST DEPTH
GAUGE BARS UP
OR DOWN AS
REQUIRED TO
CHANGE DEPTH
OF CULTIVATION
To adjust the depth gauge bars, remove the nuts
from the U-bolt securing each bar to the frame.
Then reposition the U-bolt in another set of holes
for the desired depth of cultivation. The bars can
be adjusted up or down in 1" increments. Be sure
to use the same matching pairs of holes in each
depth gauge bar to ensure the cultivator is level.
3. Up to 160 lbs. of weight may be added to help
increase penetration. 40 lb. suitcase weights can
be attached to the center weight bracket, or concrete blocks or other weights may be tied or
strapped to the cultivator frame. Before adding
weight, the cultivator should be attached to the
tow vehicle and lowered to the ground.
FIGURE 8
MAINTENANCE
1. Check for and tighten any loose hardware before
each use.
2. Clean the cultivator and lightly oil only bare metal
after each use.
3. Remove all dirt and rust. Touch up paint before
placing cultivator in storage.
4. Store cultivator inside a dry area.
6
Page 7
REPAIR PARTS FOR MODEL NO. 45-0355-131
3 PT. HITCH TANG CULTIVATOR
6
1
2
18
19
5
15
16
7
1
3
12
11
8
10
9
7
5
13
4
14
8
10
17
23
7
9
7
19
18
24
20
21
22
REF. PART QTY. DESCRIPTION
NO. NO.
1 48982 2 Lock Washer, 7/8"
2 48970 2 Hex Nut, 7/8"
3 25154 1 Cross Brace
4 25167 1 Spacer, Mast Lift Strap
5 25180 2 Mast Lift Strap
6 43343 1 Haircotter Pin, 1/8" x 2-3/8"
7 712-3083 5 Hex Nut, Nylock, 1/2"
8 25158 2 Mast Side
9 48979 2 Category 1 Pin
10 25169 2 Mast Extension Strap
11 46526 1 Hex Bolt, 1/2" x 3-1/2" Lg.
12 48978 1 Pivot Pin, 3-3/4" Lg.
18
23
18
REF. PART QTY. DESCRIPTION
NO. NO.
13 HA180132 2 Hex Bolt, 3/8" x 2-1/4" Lg.
14 43001 2 Hex Bolt, 3/8" x 1" Lg.
15 25191 1 Weight Bracket
16 25192 1 Support Bracket
17 43020 2 Hex Bolt, 1/2" x 1-1/2" Lg.
18 HA21362 26 Hex Nut, Nylock, 3/8"
19 43510 2 Hex Bolt, 1/2" x 2-3/4" Lg.
20 64772 1 Cultivator Frame Assembly
21 25170 9 Tang Support Strap
22 43022 9 Cultivator Tang
23 46853 11 U-Bolt, 3/8"
24 24238 2 Depth Gauge Bar
49358 1 Owners Manual
the fastest way to purchase parts
7
www.speedepart.com
Page 8
the fastest way to purchase parts
REPAIR PARTS
Agri-Fab, Inc.
303 West Raymond
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
www.speedepart.com
Loading...