Page 1
• Safety
• Assembly
• Operation
• Maintenance
• Parts
the fastest way to purchase parts
www.speedepart.com
™
Page 2
1
2
3
7
8
6
5
4
Read this owner's manual before attempting to assemble
Read the towing vehicle owner's manual and know
Do not allow anyone to ride on or sit on spreader.
Never allow children to operate the tractor or spreader
Do not allow adults to operate the tractor or spreader
Read the chemical label for instructions and
cautions for handling and applying chemicals.
Wear eye and hand protection when handling and using
Always begin with the transmission in fi rst (low) gear and
Do not drive too close to a creek or ditch and be alert
Before operating the vehicle on any grade (hill) refer to
Follow maintenance and lubrication instructions as
Page 3
A B C D
F
G
H
I
J
K
SHOWN FULL SIZE
L
M
N
NOT SHOWN FULL SIZE
E
REF. QTY. DESCRIPTION
A 1 Hex Bolt, 3/8" x 1"
B 1 Hex Bolt, 1/4" x 1-1/4"
C 2 Hex Bolt, 1/4" x 3/4"
D 10 Hex Bolt, 1/4" x 5/8"
E 1 Carriage Bolt, 1/4" x 3/4"
F
G
REF. QTY. DESCRIPTION
I
J
L
Page 4
NYLON
WASHER
1/4" FLAT
WASHER
1/4" x 1-1/4"
HEX BOLT
PLASTIC
GRIP
FERRULE
FLOW
CONTROL
ROD
FLOW
CONTROL
ARM
HOPPER
BRACE
1/2"
1/4" NYLOCK
NUTS
x 1-1/4" hex bolt, a 1/4" fl at washer and two 1/4" nylock
the fi rst nylock nut
tighten
the second nylock nut.
1/4" NYLOCK NUT
1/4" x 5/8"
HEX BOLT
TONGUE
3/8" NYLOCK NUT
1/4" x 5/8"
HEX BOLT
3/8" x 1"
HEX BOLT
1/4" FLAT WASHER
(ONE ONLY)
HOPPER
BRACE
HITCH
BRACKET
1/4" NYLOCK
NUT
See fi gure 3.
assembled so far. See fi gure 3.
Page 5
See fi gure 4.
x 5/8" hex bolt and 1/4" nylock nut in the front hole of
tighten
all
1/4" NYLOCK NUT
BRACKET
FERRULE
FLOW CONTROL ROD
fi nger tight
1/4" x 5/8"
HEX BOLT
1/4" FLAT WASHER
(One per side)
1/4" NYLOCK NUT
TONGUE
BRACE
1/4" x 3/4"
HEX BOLT
1/4"
NYLOCK
NUT
1/4" x 5/8"
HEX BOLT
PLASTIC
KNOB
NYLON
WASHER
1/4" x 3/4"
CARRIAGE BOLT
FLOW
CONTROL
GAUGE
1/8" HAIR
COTTER PIN
3/8" HITCH PIN
Tighten
the lock nuts and then loosen 1/4 turn.
fl ow control gauge at a mid range setting.
Page 6
material,
3 M.P.H. and increase the setting for higher speeds.
PLASTIC
KNOB
FLOW RATE
SETTING (6)
0
1
2
4
6
FLOW CONTROL ARM
ON
Always place fl ow control arm in the "OFF"
Flow Rate Setting
MATERIAL TYPE At 3 M.P.H.
Fertilizer Granular / Pelleted 0-1 / 0-2
Grass Seed Fine / Coarse 5-6 / 7-8
Page 7
NO. NO.
NO. NO.
NO. NO.
1 47451 1 Hopper
2 24536 1 Hopper Center Plate (Small)
3 24535 1 Hopper Center Plate (Large)
4 43088 9 Washer, 1/4"
5 43866 16 Bolt, Hex 1/4-20 x 5/8"
6 47189 24 Nut, Nylock 1/4-20 Thd.
7 741-0245 2 Bearing, Flange
8 47484 1 Bearing, Hex Flange
9 24538 1 Bracket, Feed Plate (RH)
10 24539 1 Bracket, Feed Plate (LH)
11 47711 2 Ferrule
12 728-3001 10 Pop Rivet
13 47459 1 Skirt, 48"
14 47508 1 Retainer, Skirt
15 24537 2 Flow Plate
16 43009 12 Washer
17 47259 4 Agitator Blade
18 47476 16 Screw, #8-32 x 3/8" Lg.
19 24540 2 Axle
20 46497 2 Spacer, Tube 1" OD x 1.2" Lg.
21 47458 2 Spacer, 1.25" OD x .330" Lg.
22 24534 2 Plate, Bearing
23 44457 2 Wheel
24 1509-69 2 Bolt, Hex 1/4-20 x 1-3/4" Lg.
25
26 47712 1 Rod, Flow Control
27 24660 1 Arm, Flow Control
28 24542 1 Gauge, Flow Control
29 63850 1 Brace Assembly, Hopper
30 24532 2 Brace, Tongue
31 23014 1 Hitch Bracket
32 24531 1 Tongue
33 43012 2 Bolt, Hex 1/4-20 x 3/4"
34 44950 1 Bolt, Carriage 1/4-20 x 3/4" Lg.
35 1543-69 3 Washer, Nylon
36 43849 1 Knob, Plastic 1/4-20 Thd.
37 43848 1 Grip, Plastic
38 43001 1 Bolt, Hex 3/8-16 x 1" Lg.
39 HA21362 1 Nut, Nylock 3/8-16 Thd.
40
41 1509-90 1 Bolt, Hex 1/4-20 x 1-1/4" Lg.
42 43601 2 Washer, 1" ID x .06" Thick
47717 1 Owners Manual
4
5
9
10
1
2
3
4
4
5
5
5
5
33
6
6
7
8
14
15
16
16
16
17
18
19
19
19
20
21
22
23
24
A
6
6
28
29
34
35
36
38
25
15
13
42
6
6
30
31
32
39
40
5
6
11
A
27
35
35
4
37
41
B
11
26
12
B
6
5
6
Page 8
the fastest way to purchase parts
www.speedepart.com
Loading...