AG Neovo TS- series User Manual

Table of Contents

Precautions ..................................................................................... 2

Notice.......................................................................................... 2

Installation ................................................................................... 2

Warning on power connection ..................................................... 2

Maintenance................................................................................ 3

Transportation ............................................................................. 3

Wall mounting.............................................................................. 5

Getting Started ................................................................................ 7

Package Contents ....................................................................... 7

Setup........................................................................................... 9

Connections .............................................................................. 10

Software Configuration .............................................................. 13

Identifying Parts and Controls.................................................... 14

Customizing Your Monitor.............................................................. 15

OSD Control Buttons................................................................. 15

15” OSD Menus......................................................................... 16

17” OSD Menus......................................................................... 20

Warning Messages and Troubleshooting....................................... 24

Warning Messages.................................................................... 24

Troubleshooting......................................................................... 25

Technical Features and Specifications........................................... 26

Specifications ............................................................................ 26

Plug & Play................................................................................ 27

Regulations ................................................................................... 28

FCC compliance........................................................................ 28

WEEE........................................................................................ 29

Hg.............................................................................................. 29

1

Precautions

Notice

• Srmation was correct at time of print. All information is subject to change without notice.

Updated content can be downloaded from our web site at http://www.agneova.com.

• To register online, please go to http://www.agneovo.com.

• To protect your rights as a consumer, do not remove any stickers from this product.

Doing so may affect the determination of the product’s warranty period.

Installation

• Do not cover or block the ventilation holes in the housing.

• Do not place the monitor near a heat source, such as a space heater or exhaust vent,

nor in direct sunlight.

• Do not place this device in any location subject to vibration or other physical shocks.

Warning on power connection

• Use an appropriate power cord to connect the monitor to a power outlet.

• The outlet should be installed near the monitor and be easily accessible.

• Do not allow anything to rest on the power cord.

• Disconnect the power plug from the power outlet in the following circumstances:

 If you will not use the monitor for an indefinite period time.

 When the power cord or plug is damaged of frayed.

 If the product has been dropped or the housing has been damaged.

 If the product exhibits a distinct change in performance, indicating a need for

service.

2

Maintenance

• Clean the housing, glass panel and controls with a soft cloth lightly moistened with a

mild detergent solution. Do not use any type of abrasive pad, scouring powder or

solvent, such as alcohol or benzene.

• Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as

a pen or screwdriver. This type of contact may result in scratching the surface of the

glass.

• Do not insert sharp objects or spill liquid into the monitor through ventilation holes. This

may cause accidental fire, electric shock or failure of the device.

• Do not attempt to service this product yourself, as opening or removing covers may

expose you to dangerous voltages or other risks.

Transportation

When you transport this monitor for repair or shipment, use the original carton and packing
materials.

Retracting the base stand

15”

Warning: If you wish to retract the base stand for storage, moving, or wall-mounting the

device, first push back the fold switch to prevent possible damage to the base stand.

3

17”

Note: A tilt dial is fitted to the base stand as shown in the figure. Use it to control the

angle of tilt of the monitor.

This dial has “Base Lock”, “Neutral” and “Tilt Lock” three positions, which are described
as follows:

Base Lock―

Locks the base stand in the fully tilted position, when it is fully retracted, to prevent it from

being opened by vibrations during transportation.

Neutral―

When the dial is set to the “Neutral” position, you can either open or retract the base stand.

Fold Lock―

This prevents the monitor from tilting more than 25°.

When you first remove the package and take out the monitor, the dial is set to the “Base
Lock” position. To open the base stand, you only need to turn the dial slightly
counterclockwise to “Base Release” position and release, it will automatically turn
clockwise and reset to “Neutral”. Now, you can push with little force to open the base stand.
When the monitor is tilted at an angle less than 25°, the dial again to go clockwise until it
reaches the title limit “Fold Lock” position.

The maximum tilting angel of the monitor is 25°. When the monitor is tilted at 25°, the control
device brakes so that further tilting is not possible. To retract the base stand, first turn the
dial slightly counterclockwise and hold it (if the monitor is tilted to the limit, the dial cannot be
turned. The tilting angel must be reduced to 25° or smaller before the dial can be turned
again) and then press down the monitor until it is fully retracted. Remember to turn the dial
counterclockwise to “Base Lock” position to ensure that the base stand is really secure.

4

Wall mounting

This display conforms to the VESA’s Flat Panel Monitor Physical Mounting Interface
(FPMPMI) standard. You can choose relevant mounting arms or wall mounts to be used for
mounting.

The 15” monitor weighs approximately 4.6 kg (10.1 lb), and is installed by the following
steps:

1. Retract the base stand. (Refer to the section “Retracting the base stand” before doing

so).

2. Secure the base stand to the display’s housing

with two M4*18mm screws.

(AG Neovo’s wall-mountable products come

with two such screws.)

3. The base stand has four M4 screw holes,

and conforms to the VESA FPMPMI standard,

measuring 75 x 75 mm.

AG Neovo wall-mountable products (wall mount kit, WMK series) are recommended.

5

The 17” monitor weighs approximately 7.57 kg(16.11lb), and is installed by the following
steps:

1. Retract the base stand.

(Refer to the section “Retracting the base stand” before doing so).

2. The 17” monitor is supplied with two stud bolts.

First tighten these two bolts on the rear

housing of the monitor.

3. There are two holes on the rear housing and

two holes for M4 screws on the base stand

which comply with the installation interface

standard for a VESA Flat Panel Display (FPD)
of 100*100mm。

AG Neovo wall-mountable products (wall mount kit, WMK series) are recommended.

6

Getting Started

Package Contents

Before using this monitor, check if the following items are included in your carton box:

• Monitor (*1)

• Power adapter (*1)

Use only the following power adapter: Lien LE-9702B+5012。

• Power cable (*1)

The included power cable conforms to the IEC 60227 standard or relevant national

standard, with conductors providing a cross-sectional area of 3 x 0.75min, type

H05VV-F or H03VV-F.

• D-sub 15-pin VGA signal cable (*1)

• DVI signal cable (*1) (17” accessory)

• Touch Screen Cables（The following accessories are supplied depending on models）

 RS-232 signal cable (*1)

 USB signal cable (*1)

7

• Touch screen supporting bracket (*1) and screws (*2)

15”

17”

• AG Neovo Disk (*1) (User’s Manual and driver software)

• Touch-screen Disk (*1) (Touch screen driver)

• Quick Guide (*1)

• Stud bolts (*2) (for 17”monitor wall mounting only)

8