AGL MR360R, MD360R User Manual

MR360R

Operating Manual

Manuel d’ utilisation

- 1 -

WARRANTY/ GARANTIE

The manufacturer warrants its measuring instruments
against all manufacturing defects for a period of one year
from the date of purchase. If during the warranty period,
the product is considered as defective by the
manufacturer, the latter will decide whether to repair or
exchange the product. The only obligation and sole
recourse of the buyer will be limited to this repair or
exchange.The manufacturer, the distributor or the retailer
will in no case be responsible for any incident or
consequence, damage,etc,relative to the use of those
instruments.

LIMITS & EXCLUSIONS: the warranty will not apply to any
damage resulting from negligence, accident, misuse,
repair or storage, or in case of abnormal use.

Les fabricants garantissent les instruments de mesure
qu’ils fabriquent contre tous vices de production pour une
période d’un an à compter de la date d’achat. Si pendant
cette période de garantie un instrument est prouvé
défectueux au fabricant, il sera réparé ou remplacé au
choix du fabricant. L’unique obligation et le seul recours
de l’acheteur ou de loueur seront limités à cette
réparation ou ce remplacement. Le fabricant, le
distributeur ou le revendeur ne seront en aucun cas
responsables pour aucun incident ou conséquence,
dommage, etc., relatifs à l’utilisation de ces instruments.

LIMITES & EXCLUSIONS : la garantie ne s’applique pas à
tous les défauts résultant d’une négligence, accidents,
dommage, mauvaise utilisation, réparation ou stockage,
ou a tout autre usage autre que l’utilisation normale.

- 2 -

Description

The MR360R is a laser cell of reception
especially conceived for all your machine
control applications. Accurate, reliable, robust
and waterproof, it will be bear at the difficult
conditions of the building sites.
It detects the beam from visible or infrared
laser. Four large detection windows pick up the
beam on 360 degrees with a range of 25 cm.

Using the MR360R

Press the red ‘On/Off’ button on the bottom of
the receiver.
Each led will blinks in sequence as a self test.
The receiver will be in coarse mode.
To change the accuracy to fine mode, press
again the red ‘On/Off’ button. The two leds
located each side of the center led will blink 3
times simultaneously.
To turn off the receiver, keep the red ‘On/Off’
button pressed during 3 seconds. Leds will blink
from the center to the two extremities.

Attachment

For quick setup from the machine, the receiver
can be ordered with two adjustable clamps or
with magnets.
The clamps on the MR360R can be attached to
a round pipe with a minimum diameter of 40
mm.

Power

The MR360R receiver is equipped with
rechargeable battery (NiCd type). A 110V/240V
charger is included. Charging time is 16 hours.

- 3 -

Positioning the MR360R for excavating

MR360R with clamps:

The beam of the shovel must equipped with a
support (tube of ∅ 40 mm and length 100 cm

minimum) be assembled and welded onto
mounting feet to 150 cm of the beam. You can
also use our magnetic medium SM400 (in
option) which will allow you a fast assembly, or
to change shovel into a few minutes.

- Using your rotary laser and of its cell of
manual reception, to dig and determine the
sub grade of your earthwork.

- To position the beam vertically and to pose

the dish of the cup at the coast previously
given.

- You can carry out your earthwork: to take your

points of control, it will always be necessary to
vertically position your beam and your cup flat
(in the initial position of your adjustment)

MR360RA (magnets):

The MR360RA avoids the assembly of a

support on the beam of the shovel, but the
adjustment on the central indicator is more
difficult to carry out because of the power of the
magnets. It is thus advised to show the laser
on a tripod with toothed rack in order to more
easily regulate the beam on the central
indicator of the cell.

- The remainder of the procedure will remain

identical to the MR360R with clamps.

- 4 -

MD360R Remote display

The MR360R receiver can be connected to the
MD360R remote display inside the cabin thanks
to a radio frequency communication.

This system is conforming to the European
standard R&TTE and American standard FCC:

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.

It allows a low cost and an easier installation
(wireless). Place the remote display inside the
cabin. It allows you to view the led arrows
without taking your eyes off your machine’s
cutting edge.

- 5 -