Agilent E4445A Instrument Messages and Functional Tests

Download

Page 1

Instrument Messages and

Functional Tests

Agilent Technologies

PSA Series Spectrum Analyzers

and

ESA Series Spectrum Analyzers

Manufacturing Part Number: E4440-90619

Supersedes: E4440-90334

Printed in USA

June 2008

Page 2

Notice

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Where to Find the Latest Information

Documentation is updated periodically. For the latest information about Agilent PSA or ESA spectrum analyzers, including firmware upgrades and application information, please visit the following Internet URLs:

http://www.agilent.com/find/esa

http://www.agilent.com/find/psa

Page 3

Contents

1. Instrument Messages

Instrument Messages Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Error Queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Error Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Error Message Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Instrument Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Instrument Messages Without Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

2. Functional Tests

What You Will Find in Chapters 2, 3, and 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

What Are the Functional Tests? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Functional Test Versus Performance Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Chapters 2, 3, and 4 include the following: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Before Performing a Functional Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

3. PSA Functional Tests

Amplitude Accuracy at 50 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Testing Option 1DS (Preamp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Displayed Average Noise Level (DANL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Test Limits (with 0 dB input attenuation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Frequency Readout Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Frequency Response (Flatness) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Amplitude Linearity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Second Harmonic Distortion (SHD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

4. ESA Functional Tests

Displayed Average Noise Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

Page 4

Contents

Table of Contents

Procedure (10 MHz to 500 MHz) E4401B and E4411B E7401A . . . . . . . . . . . . . . . . . . . . .142

Procedure (501 MHz to 1.0 GHz) E4401B and E4411B E7401A . . . . . . . . . . . . . . . . . . . .143

Procedure (1.01 GHz to 1.5 GHz) E4401B and E4411B E7401A . . . . . . . . . . . . . . . . . . . .145

Procedure (10 MHz to 1 GHz) E4402B, E4403B, E4404B, E4405B, E4407B, and E4408B

E7402A, E7403A, E7404A, and E7405A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146

Procedure (1.01 GHz to 2 GHz) E4402B, E4403B, E4404B, E4405B, E4407B, and E4408B

E7402A, E7403A, E7404A, and E7405A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148

Procedure (2.01 GHz to 3.0 GHz) E4402B, E4403B, E4404B, E4405B, E4407B, and E4408B

E7402A, E7403A, E7404A, and E7405A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149

Procedure (3.01 GHz to 6.0 GHz) E4404B, E4405B, E4407B, and E4408B E7403A, E7404A,

and E7405A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150

Procedure (6.01 GHz to 6.7 GHz) E4404B E7403A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151

Procedure (6.01 GHz to 12.0 GHz) E4405B, E4407B, and E4408B E7404A and E7405A 152

Procedure (12.01 GHz to 13.2 GHz) E4405B E7404A . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153

Procedure (12.01 GHz to 22 GHz) E4407B and E4408B E7405A . . . . . . . . . . . . . . . . . . . .154

Procedure (22.01 GHz to 26.5 GHz) E4407B and E4408B E7405A . . . . . . . . . . . . . . . . . .155

EMI Detector Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159

200 Hz Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160

9 kHz Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160

120 kHz Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161

Frequency Readout Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164

Marker Count Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166

Frequency Response (Flatness) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169

Reference Level Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172

Log Mode Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173

Linear Mode Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175

Resolution Bandwidth Switching Uncertainty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178

Scale Fidelity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181

Second Harmonic Spurious Responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185

Page 5

Contents

Tracking Generator Level Flatness: Models E4401B and E4411B E7401A, Options 1DN and

1DQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

Tracking Generator Level Flatness: E4402B, E4403B, E4404B, E4405B, E4407B and E4408B

E7402A, E7403A, E7404A, and E7405A, Option 1DN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

Test Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

Test Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

Table of Contents

Page 6

Contents

Table of Contents

Page 7

Instrument Messages

Alphabetical Listing

* (Invalid Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

*CLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

*CLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

<directoryname> directory deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

<directoryname1> directory renamed to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

<filename> file copied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

<filename> file deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

<filename> file loaded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

<filename> file saved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

<filename> too many data entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

<filename1> file renamed to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

<name1> directory renamed to <name2> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

<name1> file renamed to <name2> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

’10101010’ pattern not detected - results may be inaccurate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

100 spurs found. Additional spurs ignored . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

10537 Cancellation trace has different X-Scale to Smoothed trace. . . . . . . . . . . . . . . . . . . . . . . . . . 79

1st LO Unlock; Failure acquiring FracN LO frequency lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

1st LO Unlock; Failure acquiring single loop FracN LO lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

26.5 - 50 GHz preselector bypassed, can’t adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

2nd LO Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

3 − 26.5 GHz preselector bypassed, can’t adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Instrument Messages

−350, Queue overflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

4th LO Unlock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

50 MHz Osc Unlevel (50 MHz Osc Unleveled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

AC Coupled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Acquiring Data.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Actual Trig Delay = Remote Trig Delay + Remote Trig Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

ADC Align Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

ADC overload -- Carrier not at expected frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Agilent PSG-A Series Signal Generators not supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Align Now All Needed (Align Needed). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Page 8

Instrument Messages

Alphabetical Listing

Align Now RF Needed (Align Now RF Needed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Align RF Skipped (Align RF Skipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Align RF Skipped, Align signal amplitude too low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Align . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109

Alignment Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Allowable CF for current span exceeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Allowable span for current center frequency exceeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Attempt to change amplitude units to an absolute unit which is not allowed with Normalize. . . . .60

Attempt to change Scale Type to LIN which is not allowed with Normalize. . . . . . . . . . . . . . . . . . .60

Attempt to change signal data failed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97

Instrument Messages

Atten auto set to 15 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

Audio data acquisition failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Audio level is out of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Auto Align not available when using Calibration Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Auto ranging... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

Average Type incompatible for scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Avg Mode changed to Exp for Examine Meas Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Avg Mode changed to Exp for Examine Meas Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Avg Mode changed to Repeat for Full Meas Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Avg Mode changed to Repeat for Full Meas Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Awaiting trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Awaiting Trigger, no AUTO Trig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Awaiting valid signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97

B7D and/or B7E not found. Code Domain not available.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

B7D and/or B7E not found. Mod Acc not available. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

B7D DSP Code Fail. Reload Opt BAH. Contact your Service Center . . . . . . . . . . . . . . . . . . . . . . . . .64

B7D DSP Code Fail. Reload Opt BAH. Contact your Service Center. . . . . . . . . . . . . . . . . . . . . . . . .64

B7D DSP Code Fail. Reload Opt. 202. Contact your Service Center . . . . . . . . . . . . . . . . . . . . . . . . .73

B7D DSP Code Fail. Reload Opt. 202. Contact your Service Center. . . . . . . . . . . . . . . . . . . . . . . . . .73

B7D DSP Code Install Fail Opt.229. Contact your Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . .74

B7D DSP Code Install Fail Opt.231. Contact your Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . .75

Page 9

Instrument Messages

Alphabetical Listing

B7D DSP Code Reload Fail Opt.229. Contact your Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . 74

B7D DSP Code Reload Fail. Opt.231. Contact your Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . 76

Bad or missing floppy disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Bad or missing floppy disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Bad, missing, or unformatted disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Bad, missing, or unformatted disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Band Measurement not defined for Out of Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Block data error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Block data not allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Break freq > FFT filter edge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Burst Delay out of limit for EVM (2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Burst not found. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Burst not found. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Cal Data corrupt. Wideband cal failed. Using previous data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Cal file not initialized correctly, <filenumber> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Cal Oscillator Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Calibration failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Can not get long code phase (RS-232) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Can’t Auto-Couple RBW in Zero Span. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Can’t Auto-Couple Sweep Time in Zero Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Instrument Messages

Can’t Auto-Couple Sweep Time in Zero Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Can’t compute result - not enough transitions.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Cancellation disabled while measuring DANL Floor.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Cancellation trace is not set to Reference or has no data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Cannot correlate to input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Cannot correlate to input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Cannot correlate to input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Cannot correlate to input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Cannot correlate to input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Cannot display Ref Trace because it has no data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Page 10

Instrument Messages

Alphabetical Listing

Cannot find the Power vs Time Limits File.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Cannot find the Power vs Time Limits File.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Cannot load a directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Cannot load a directory, please choose a file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Cannot locate the file that contains the list of cable types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Cannot lock to carrier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Cannot open trace file for writing. Save Failed.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Cannot save Ref Trace because it contains no data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Cannot save Trace because it contains no data.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Cannot sync DPCCH pilot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Instrument Messages

Cannot synchronize frame trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Cannot synchronize to RF amplitude (burst error) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Cannot update the list of cable types on drive C:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Cannot update the list of cable types.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Carrier frequency outside device’s transmit band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Carrier Not Present . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Carrier Not Present. Verify frequency and amplitude settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Carrier Not Present. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Carrier Not Present. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Carrier Not Present. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

Carrier power too low for optimum dynamic range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Carrier Present. Test Stopped! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Channel center frequency outside device’s transmit band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Channel frequency outside device’s transmit band.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Character data error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Character data not allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Character data too long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

CMD ERR, <name of offending command> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

CMD NOT SUPPORTED, <command> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Command error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Page 11

Instrument Messages

Alphabetical Listing

Command header error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Command not recognized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Command not supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Command not valid in this mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Command not valid in this model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Command not valid when no measurement is active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Connect Amptd Ref Output to Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Connect RF OUT to INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Connection could not be established with specified IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Connection with Source could not be established at the IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Connection with Source could not be established . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Connection with the Presel could not be established at the IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Corrupt media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Corrupted file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Corrupted file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Critical memory shortage occurred . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Critical memory shortage occurred.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Data corrupt or stale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Data corrupt or stale; EEPROM copy of <file> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Data corrupt or stale; EEPROM copy of <file> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Data corrupt or stale; NRAM copy of <file> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Instrument Messages

Data corrupt or stale; RAM copy of <file> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Data is too short to measure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Data out of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Data questionable; EEPROM copy of <file> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Data type error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

DC Coupled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Default spur table values loaded. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Demod Format setting does not allow this value for Points/Symbol. . . . . . . . . . . . . . . . . . . . . . . . . 75

Demod ON: reduce span for audible detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Device = Mobile. Code Domain not available. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Page 12

Instrument Messages

Alphabetical Listing

Device = Mobile. Mod Acc not available.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Device-specific error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Diagnostic override of Firmware Control; :DIAGnostic:ABUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Diagnostic override of Firmware Control; :DIAGnostic:AMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Diagnostic override of Firmware Control; :DIAGnostic:LATCh . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Diagnostic override of Firmware Control; :DIAGnostic:MLATCh . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Diagnostic override of Firmware Control; :DIAGnostic:REGister:VALue . . . . . . . . . . . . . . . . . . . . .47

Diagnostic override of Firmware Control; :DIAGnostic:SBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Diagnostic override of Firmware Control; :DIAGnostic:SBUS:DBD . . . . . . . . . . . . . . . . . . . . . . . . .47

Diagnostic override of Firmware Control; :DIAGnostic:SIO:PARallel . . . . . . . . . . . . . . . . . . . . . . . .47

Instrument Messages

Diagnostic override of Firmware Control; :DIAGnostic:SIO:SERial . . . . . . . . . . . . . . . . . . . . . . . . .47

Did not find 4 signals > Peak Excursion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Directory already exists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Directory already exists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

doing Alignment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

DSP algorithm timeout, aborting measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

DSP timed out, resetting DSP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Dynamic range not optimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

EDGE EVM only supports EDGE TCH burst type (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

EDGE EVM only supports EDGE TCH burst type (Ref Burst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

EDGE ORFS only supports EDGE TCH burst type (Burst Type). . . . . . . . . . . . . . . . . . . . . . . . . . . .67

EDGE ORFS only supports EDGE TCH burst type (Ref Burst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

EDGE PVT only supports EDGE TCH burst type (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

EDGE PVT only supports EDGE TCH burst type (Ref Burst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

EDGE Upgrade (252) unlicensed. Please contact your Agilent Sales Rep. . . . . . . . . . . . . . . . . . . . .73

EEPROM checksum for . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

EMC Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Emission bandwidth not found. Consider increasing span. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

ENR table will be extrapolated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Entire trace is below the threshold level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Page 13

Instrument Messages

Alphabetical Listing

Entire trace is below threshold level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Error reading file: CDMASTUN.CSV. Please reinstall cdmaOne.. . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Error reading file: CDPDMDA. Please reinstall cdmaOne. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Error reading file: CDPPMCO. Please reinstall cdmaOne. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Error reading file: CDPPMDA. Please reinstall cdmaOne. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Error reading file: OOBSTAB.CSV. Use Edit Table | Save Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Error reading file: RHODMDA. Please reinstall cdmaOne.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Error reading file: RHOPMCO. Please reinstall cdmaOne. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Error reading file: SPCLIMIT.CSV. Cannot use custom limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

EVM Measurement only supports EDGE TCH burst type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Excessive 50 MHz RF input power is preventing internal alignments . . . . . . . . . . . . . . . . . . . . . . . 46

Execution Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Exponent too large . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Expression data error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Expression data not allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Ext Ref. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Ext Ref. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Ext Ref. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

External LO frequency out of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

External mixing is off, can’t adjust external preselector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

External reference missing or out of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Instrument Messages

Failed to Initialize ISTATE regions. Fatal LDS error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Failed to load ENR data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Failed to load Frequency List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Failed to load Limit line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Failed to load Loss data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Failed to Load trace. Bad file format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Failed to store ENR data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Failed to store Frequency List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Failed to store Limit line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Failed to store Loss data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Page 14

Instrument Messages

Alphabetical Listing

Failed to store Trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

File access IO busy; duplicate :SERVice[:PRODuction]:CALibrate:BEGin . . . . . . . . . . . . . . . . . . . .53

File access IO busy; :SERVice[:PRODuction]:CALibrate:END without a BEGin . . . . . . . . . . . . . . .53

File access is denied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

File already exists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File already exists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

File already exists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

File does not exist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

File exists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File exists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Instrument Messages

File is corrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File is corrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

File name error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File name error; Directory does not have a default file type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error; Directory does not have a default file type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File name error; Directory does not support extenders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error; Directory does not support extenders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File name error; Empty filename . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error; Empty filename . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File name error; Illegal extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error; Illegal extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File name error; Illegal filename character . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error; Illegal filename character . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File name error; Only one extender character allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error; Only one extender character allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File name error; Only one: is allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

File name error; Only one: is allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

File not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

File not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

File Operation Status; <name> directory deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Page 15

Instrument Messages

Alphabetical Listing

File Operation Status; <name> directory renamed to <name> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

File Operation Status; <name> file copied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

File Operation Status; <name> file deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

File Operation Status; <name> file loaded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

File Operation Status; <name> file renamed to <name> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

File Operation Status; <name> file saved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

File Operation Status; directory <name> created . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

File Operation Status; Volume <name> formatted. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Final IF Overload (IF/ADC Overrange). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Final IF Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

First harmonic is past analyzer frequency limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

First IF Overload (IF/ADC Overrange) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Flash memory is full . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Flat corr off (no corresponding status bit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Floppy disk error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Floppy disk full . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

FM Demod Align Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Freq band crossing not supported by Option 215 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Freq corr off (no corresponding status bit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Freq Count: Reduce Span/RBW ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Freq Count: Reduce Span/RBW ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Instrument Messages

Freq outside cal range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Freq range of ext src exceeded, PSA setting adjustments required. . . . . . . . . . . . . . . . . . . . . . . . . . 93

FreqRefUnlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Frequency crossing Conducted and Radiated Band is not supported . . . . . . . . . . . . . . . . . . . . . . . . 97

Frequency Hopping enabled, waiting for valid burst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Frequency Reference Error (Freq Ref Unlocked) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Gate option not installed. Results may not be accurate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Gate option not installed. Results may not be accurate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

GET not allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

GSM burst out of limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Page 16

Instrument Messages

Alphabetical Listing

GSM Hopping enabled, waiting for valid burst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

GSM Pwr Meas requires trig delay < −50 µs. Delay set to −50 µs . . . . . . . . . . . . . . . . . . . . . . . . . . .81

GSM RF sync delay is out of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Hardkeys are disabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Hardware missing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Hardware missing; no such SIO address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Hardware upgrade required. Option 215 disabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

Header separator error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Header suffix out of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

HW Average . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Instrument Messages

HW Diag is OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

IF Align Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

IF BW is clipped to its limit because of IF Path change.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

IF Gain fixed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

IF over range req. RF re-range: Meas Restarted. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

IF Overload (IF/ADC Over Range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

Illegal MSDOS name given . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

Illegal parameter value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Illegal write access of Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

In <command>: bad data count (<numeric_value>): expected multiple of <numeric_value> . . . . . .56

In <filename>, line <nnn>: separator missing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

In <filename>, line <numeric_value>: <xxx> is not numeric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

In <filename>, line <numeric_value>: error parsing tokens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

In <filename>, line <numeric_value>: line too long. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

In <filename>: [DATA] header missing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

In <filename>: bad amplitude unit <unit> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

In <filename>: error reading file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Incompatible Hardware (Third Converter) for E4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Incompatible Hardware found for E4447A: Third Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

Inconsistent sync word . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Incorrect filename, allowable extension ENR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Page 17

Instrument Messages

Alphabetical Listing

Incorrect filename, allowable extension is .sta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Incorrect filename, allowable extension LOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Incorrect filename, allowable extension LST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Incorrect filename, allowable extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Incorrect filename, allowable extensions are .gif or .wmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Incorrect filename, allowable extensions are .gif or .wmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Incorrect filename, allowable extensions are .trc or .csv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Incorrect filename, allowable extensions are .trc or .csv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Incorrect filename, allowable extensions LIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Incorrect RBW for demod - change RBW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Incorrect trigger holdoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Input is internal (no corresponding status bit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Input overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Input overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Input power too low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Input power too low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Input power too low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Instrument mode requested is not supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Instrument state may be corrupt, state has been reset to initial values. . . . . . . . . . . . . . . . . . . . . . 57

Instrument state set to initial values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Insufficient pre-Trig for demod - decrease Trig Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Instrument Messages

Interpolation error: cannot compute log of <negative_frequency_value> . . . . . . . . . . . . . . . . . . . . . 57

Invalid Baud Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Invalid block data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Invalid character data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Invalid character in number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Invalid character. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Invalid EDGE burst timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Invalid expression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Invalid format: CSV files are not supported by this measurement. . . . . . . . . . . . . . . . . . . . . . . . . 100

Invalid format: CSV files are not supported by this measurement. . . . . . . . . . . . . . . . . . . . . . . . . . 78

Page 18

Instrument Messages

Alphabetical Listing

Invalid frequency list for measurement mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Invalid GSM burst timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Invalid instrument mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

INVALID ITEM, <offending item> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Invalid Marker Trace. Marker moved to Raw Trace.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Invalid option, unable to uninstall package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Invalid printer response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

INVALID SAVE REG, <invalid register> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Invalid separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Invalid State Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Instrument Messages

Invalid string data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Invalid suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

INVALID TRACE, <trace> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Level is low, results may degrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

License conflict: Options X and Y can not be licensed at same time. . . . . . . . . . . . . . . . . . . . . . . . . .50

Linear scale unavailable with Normalize on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Linear units unavailable with Normalize on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

LO – Stop freq must be >= min system input freq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

LO Align Failure (status bit only, no message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

LO Out Unlevel (LO Out Unleveled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

LO Unlevel (LO Unleveled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

LO Unlock (Synth Unlocked). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Log Corr Off (no corresponding status bit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

LOG FILE CLEARED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

LOG FILE FULL, CLEAR FOR FURTHER ERROR LOGGING . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Log Frequency Interpolation not Implemented . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Lost trigger, aborting measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Lower Custom Mask is Invalid! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Lower Custom Mask is Invalid! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Marker Count:Widen Res BW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Marker Freq Count HW Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Page 19

Instrument Messages

Alphabetical Listing

Marker X value not adjusted when right of Rise&Fall mark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Mask unavailable for current Span - increase to display mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Mass storage error; EEPROM write timeout on EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Mass storage error; EEPROM write timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Meas Interval is clipped to its upper limit because of points/symbol change. . . . . . . . . . . . . . . . . . 92

Meas Offset exceeds valid burst length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Meas Type changed to Examine for Exp Avg Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Meas Type changed to Examine for Exp Avg Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Meas Type changed to Full for Repeat Avg Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Meas Type changed to Full for Repeat Avg Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Meas Uncal (Oversweep) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Meas Uncal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Measurement does not support the current radio standard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Measurement failed for unknown reasons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Measurement halted. Press a measurement key to continue. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Measurement Input Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Measurement not defined for Out of Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Measurement outside Internal Preamp range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Measurement partially outside Internal Preamp range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Measurement suspended until carrier is turned off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Measurement uncalibrated, symbol rate exceeds +/-10% nominal. . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Instrument Messages

Measurement uncalibrated, wideband calibration required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Measuring Channel Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Measuring Offset A Positive Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Measuring Offset B Positive Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Measuring Offset C Positive Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Measuring Offset D Negative Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Measuring Offset D Positive Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Measuring Offset E Negative Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Measuring Offset E Positive Segment... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Media is corrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Page 20

Instrument Messages

Alphabetical Listing

Media is not writable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Media is not writable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Media is not writable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

Media is protected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Media is protected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

Memory limit caused Data Acquisition to be truncated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Memory shortage occurred; consider decreasing Capture Intvl . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Missing parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Missing Parameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Instrument Messages

Mode Setup Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Neg. Trig Delay unavailable in Swept Mode, zero delay used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

No Active slot is found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

No cal factor for power sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

No entries in ENR table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

No entries in frequency list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

No entries in Limit Line table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

No entries in loss table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

No error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

No Fast ADC hardware installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

No Fast ADC hardware installed. Meas unavailable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

No Fast ADC hardware installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

No Fundamental > 0 Hz found in given span. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

No Fundamental > -50 dBm found in given span. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

No Idle slot is found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

No peak found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

No Peak Found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

No power at carrier frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

No ranges are defined. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

No spurs have been found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Page 21

Instrument Messages

Alphabetical Listing

No trigger before timeout; auto-triggered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Noise Figure DLP requires Noise Source Control Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Not enough frequency range to measure harmonics for channel. . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Not enough memory. Decrease Capture Interval. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Numeric data error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Numeric data error; VGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Numeric data not allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

…Averaging unavailable when Sig ID is on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

…Cannot center unpreselected external mixer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

…Command incompatible with band pair marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

…External mixing unavailable when preamp on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

…FFT unavailable when Sig ID is on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

One or more harmonics beyond freq limit: number decreased. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

One or more harmonics past freq limit: number decreased . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Only one marker is available on Demod Bits trace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Open/Short CAL not possible, freq band crossing detected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Opt 106 demod hardware required. Meas unavailable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Opt 106 hardware required. Preamble sync unavailable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Opt 229 DSP algorithm code file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Opt 229 DSP algorithm coef. file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Opt 231 DSP algorithm code file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Instrument Messages

Opt 231 DSP algorithm coef. file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Opt 252 DSP algorithm code file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Opt 252 DSP algorithm coef. file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Opt AYX hardware required. Meas unavailable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Opt B7D bootrom requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Opt B7E RF hardware required. RF Burst unavailable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Opt BAH DSP algorithm code file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Opt BAH DSP algorithm coef. file requires upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Opt BAH DSP algorithm files failed to load, aborting measure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Opt BAH DSP algorithm files not installed. Meas unavailable. Contact your Service Center. . . . . 63

Page 22

Instrument Messages

Alphabetical Listing

Opt Freq Ref setting does not match external reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Option activated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Option B7D or AYX FADC hardware required. Meas unavailable. . . . . . . . . . . . . . . . . . . . . . . . . . .71

Option not installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Option not licensed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Options B7D & B7E hardware required. Meas unavailable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

…Settings Conflict, Preamp unavailable in external mixing mode . . . . . . . . . . . . . . . . . . . . . . . . . .41

…Sig ID requires EXTERNAL mixing mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

…Sig ID unavailable in Manual:FFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

…Sig ID unavailable when Averaging is on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Instrument Messages

…Sig ID unavailable when Signal Track is on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

…Signal ID unavailable with Presel Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

…Signal Track unavailable when Sig ID is on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Out of memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110

Overload: Reduce Signal and press <ESC> (Input Overload Tripped) . . . . . . . . . . . . . . . . . . . . . . .107

PARAMETER ERROR, <name of offending parameter> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Parameter not allowed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Parameter unavailable in demod measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Payload data pattern ‘10101010’ not present. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Peaking Signal (no corresponding status bit). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

Please set RF input range (INPUT menu) to manual first.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Point Quantities Limited . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

Points/Symbol changed to an even number because of demod format . . . . . . . . . . . . . . . . . . . . . . . .91

POW:GAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Power meter calibration failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Power meter calibration required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Power meter connection failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

Power meter connection time-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

Power meter model is not supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Power meter reading not available. Retrying to connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Page 23

Instrument Messages

Alphabetical Listing

Power meter zero and calibration required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Power meter zero failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Power meter zero required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Power sensor hardware is missing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Preferred resolution bandwidth not available. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Preferred resolution bandwidth not available. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Preselector cannot be bypassed in this mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Preselector centering failed - inadequate peak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Preselector centering failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Preselector is not available at this frequency.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Preselector unavailable while in external mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Pretrigger too long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Print failed; Can’t open print file desc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Print failed; DisplayExport can’t create print file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Print failed; DisplayExport illegal print language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Print failed; DisplayExport insufficient RAM space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Print failed; DisplayExport undetermined error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Print failed; Error transferring image to printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Print failed; Printer ioctl failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Print failed; Unknown printer response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Printer interface error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Instrument Messages

Printer not responding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Printer not responding; ioctl ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Printer out of paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Printer Type is None. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Program mnemonic too long. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Query DEADLOCKED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Query Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Query INTERRUPTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Query UNTERMINATED after indefinite response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Query UNTERMINATED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Page 24

Instrument Messages

Alphabetical Listing

Radio standard is not supported by the current measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

RBW limited to 1 kHz when Span > 5 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Requested timeslot number not present . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Require 4 Signals > PEAK EXCURSION above Threshold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Required Input attenuation not calibrated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Required payload data pattern ‘10101010’ not present. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Required payload data pattern ‘11110000’ not present.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Resolution BW < 300kHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Resolution BW <300 kHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Restoration of NVRAM data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Instrument Messages

Restoration of NVRAM data” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

RF Align Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

RF Board could not detect any bursts in signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

RF Board LO Unlocked. Contact service center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

RF Board RF Osc Unlocked. Contact service center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

RF Board SR Osc Unlocked. Contact service center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

RF frequency is beyond frequency range of cal factor table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

RF Presel conducted and radiated paths need to be aligned. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF Presel conducted paths needs to be aligned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF Presel input is overloaded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF Presel model is not supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF Presel radiated paths need to be aligned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF Preselector alignment terminated by user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF Preselector conducted band alignment fails. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF Preselector radiated band alignment fails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

RF re-range required: Meas Restarted. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

RF Signal not found. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

RS-232 Interface Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Sample Clock Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Sampling Oscillator Unlock; Failure acquiring SO frequency lock. . . . . . . . . . . . . . . . . . . . . . . . . . .46

SCPI marker query not available in GSM Rise&Fall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Page 25

Instrument Messages

Alphabetical Listing

Search Length is clipped to the lower value as allowed by current IF Band Width. . . . . . . . . . . . . 92

Search Length is clipped to the upper value according to the dependency of IF Band Width . . . . . 92

Select a valid Radio Standard/Measurement combination to enable. . . . . . . . . . . . . . . . . . . . . . . . . 67

Self-test failed; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Settings conflict; parameter currently disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Settings conflict;… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Shutdown in process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Signal exceeds maximum allowable power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Signal Ident On, Amptd Uncal (Signal Ident On). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Signal level is low.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Signal too noisy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Signal too noisy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Signal too noisy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Signal too noisy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Signal too noisy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Signal Tracking disabled when measuring DANL Floor (Removal). . . . . . . . . . . . . . . . . . . . . . . . . . 79

Signal Tracking is not available when Noise Correction is on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Signals do not fit expected Intermod (TOI) pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Slot format auto-detection not supported by slot power meas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Instrument Messages

Source LO Unlock (Source Synth Unlocked) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Source model is not supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Source Unlevel (Source Unleveled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Span limited to 5 MHz when RBW < 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Span Limited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Start – LO freq must be >= min system input freq. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Start freq must be greater than fixed LO freq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Start freq must be greater than start RF freq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Start Marker must be at least 1% < Stop Marker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Stop freq must be less than fixed LO freq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Page 26

Instrument Messages

Alphabetical Listing

Stop freq must be less than stop RF freq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108

Stop IF freq must be less than fixed LO freq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108

Stop Marker must be at least 1% > Start Marker.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Store Ref trace before turning on Normalize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Stored data length too short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

String data error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

String data not allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Suffix error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Suffix not allowed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Suffix too long. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Instrument Messages

Sweep Point/Span ratio below minimum - results may be inaccurate.. . . . . . . . . . . . . . . . . . . . . . . .68

Sweep Time too fast (<2 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Symbol Rate is clipped to its limit because of IF Path change.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

Sync is RF Ampl (not Training Seq). Bits not accurate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Sync not found on AM and PM path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Sync not found on AM path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Sync not found on PM path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Sync offset value not valid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Sync Pattern includes non-hex characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Sync Word Length changed to new upper limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Sync word not found in frame (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Sync word not found in frame (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Sync word not found in frame (Ref Burst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Sync word not found in frame (Ref Burst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Sync word not found in frame (TSC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Sync word not found in specified timeslot (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Sync word not found in specified timeslot (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Sync word not found in specified timeslot (TSC).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Sync word not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Sync word not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Sync word not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Page 27

Instrument Messages

Alphabetical Listing

Sync word not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Sync word not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Synchronization failed, check signal format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Syntax error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

System Alignments, Align Now, All Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

System error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

System error; Pretune DAC Cal failed midpoint verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

System error; Pretune DAC Calibration failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

System input frequency out of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

System, Alignments, Align All Now Needed (Align Needed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

System, Alignments, Align All Now, Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SYSTem:ERRor? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

T hot must be greater than T cold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Table could not be loaded. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Table could not be saved. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Table loaded successfully. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Table saved successfully. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

TG Align Failure (status bit only, no message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

TG Frequency Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

TG start freq is less than 1/2 res bw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

TG start freq is less than 9 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Instrument Messages

The Cable Fault Measurement is active. Mode Setup is disabled. . . . . . . . . . . . . . . . . . . . . . . . . . . 66

The calibration data is invalid, and has been cleared. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

The calibration data is invalid, and has been cleared. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

The file containing the list of cable types has been updated.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

The file containing the list of cable types has been updated.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

The regression portion failed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

There are no spurs to inspect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

There is no valid result to hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

This measurement does not support the *.CSV file format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

This measurement does not support the *.CSV file format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Page 28

Instrument Messages

Alphabetical Listing

This operation requires a measurement to be active. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

This operation requires a measurement to be active. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

This operation requires a measurement to be active. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Time resolution is low, reduce Meas Time or increase Trace Points. . . . . . . . . . . . . . . . . . . . . . . . .102

Too many data values at <freq_or_time_value>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Too many digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Too much data; not all points entered. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Trace file contains no compatible traces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Trace file saved successfully. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Trace file was created by incompatible version of Opt. 226. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Instrument Messages

Trace Menu is unavailable when Sig Ident is ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Trace smoothing: VBW filt or Average Detector; cannot use both . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Tracking Generator hardware is not present. Meas unavailable.. . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Tracking Peak Needed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

Trigger Offset unavailable in swept spans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Turn on Multi Channel Estimator to measure Timing and Phase.. . . . . . . . . . . . . . . . . . . . . . . . . .101

Two entries already exist at frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Tx Band Spur measurement does not support this frequency band . . . . . . . . . . . . . . . . . . . . . . . . . .82

Tx Band Spur measurement not defined for mobiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Unable to Calculate Result using Current Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Unable to demodulate signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Unable to format drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Unable to initialize flatness data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Unable to load file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Unable to load file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Unable to load state from file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Unable to load state from register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Unable to load state saved from firmware Rev A.xx.xx; Restore Sys\nDefaults . . . . . . . . . . . . . . . .58

Unable to load state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Unable to load user state, factory preset was done . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Unable to load user state, required instrument mode is not installed . . . . . . . . . . . . . . . . . . . . . . . .59

Page 29

Instrument Messages

Alphabetical Listing

Unable to query state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Unable to retrieve signal (remote). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Unable to save file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Unable to save file, invalid path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Unable to save state to file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Unable to save state to register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Unable to save user state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Unable to set state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Unable to store flatness data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Unable to store reference trace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Unable to uninstall personality, file not deletable.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Uncal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Undefined header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Unexpected carrier frequency (BMT only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Unknown demod status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Unknown printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Unlevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Unpreselected external mixing - no preselector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Unsupported printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Upper Custom Mask is Invalid! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Instrument Messages

Upper Custom Mask is Invalid! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Use trigger delay to align bit p0 center on marker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Use View/Trace menu when loading or saving logarithmic traces. . . . . . . . . . . . . . . . . . . . . . . . . . . 78

User cal invalidated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Valid 1xEV burst not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Valid Bluetooth burst not found. (Check Packet Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Valid burst not found in frame (Burst Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Valid burst not found in specified timeslot (Burst Type).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Valid burst not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Valid burst not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Page 30

Instrument Messages

Alphabetical Listing

Valid burst not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Valid burst not found, extend search length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

Valid burst not found. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Valid EDGE burst not found in frame (Burst Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Valid EDGE burst not found in frame (Ref Burst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Valid EDGE burst not found in specified timeslot (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Valid GSM burst not found for selected timeslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Valid GSM burst not found in frame (Burst Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Valid GSM burst not found in frame (Burst Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Valid GSM burst not found in frame (Ref Burst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Instrument Messages

Valid GSM burst not found in frame (Ref Burst). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Valid GSM burst not found in specified timeslot (Burst Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Valid GSM burst not found in specified timeslot (Burst Type).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Valid GSM burst not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Valid NADC burst not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Valid PDC burst not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Valid PRACH burst not found. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Valid signal not found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Valid signal not found. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Video bandwidth fixed at 50MHz by Option 215 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

Video shift off (no corresponding status bit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109

Video Trigger cannot be active with Average Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Video Trigger cannot be used with Mkr Func due to Average Detector . . . . . . . . . . . . . . . . . . . . . . .60

Volume <name> formatted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

Waiting for end of data acquisition to access floppy disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

WARNING: You are about to delete all of the contents of directory “x:\xxxxx\”. Press Delete Now

again to proceed or any other key to abort. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

WARNING: You are about to delete all of the contents of directory xxxxxx. Press Delete Now again

to proceed or any other key to abort. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

WBIF ADC Image Calibration Failed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

WBIF Firmware Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

WBIF Power On Test Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Page 31

Instrument Messages

Alphabetical Listing

WBIF Self Test Failed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Wideband calibration not valid until Align Now, All performed.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Wrong density floppy inserted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Instrument Messages

Page 32

Instrument Messages

Alphabetical Listing

Instrument Messages

Page 33

1 Instrument Messages

Instrument Messages

Page 34

Instrument Messages

Instrument Messages Introduction

The analyzer can generate various messages that appear on the display during operation. There are four types of messages.

This chapter describes the following types of messages displayed on the analyzer:

User Error

Messages

Informational Messages

Status Messages

Pop-up Messages

Instrument Messages

Beginning on page 38, User Error Messages appear when an attempt has been made to set a parameter incorrectly or an operation has failed (such as saving a file). These messages are often generated during remote operation when an invalid programming command has been entered. These messages appear in the status line at the bottom of the display. If you are using the default display colors, the message will appear in yellow. The message will remain until you preset the analyzer, press line.

Beginning on page 97, Informational Messages provide information that requires intervention. These messages appear on the status line at the bottom of the display. If you are using the default display colors, the message will appear in green (ESA) or yellow (PSA). The message will remain until you preset the analyzer, press line. The information provided in brackets, for example <filename> or <directory>, is a variable that represents a specific input provided previously.

Beginning on page 102, Status Messages appear on the right side of the analyzer display and/or set status bits in the SCPI Status Register system. These messages indicate a condition that may result in erroneous data being displayed. Most messages will only be displayed until the error condition is corrected. Multiple messages can be displayed and will be listed in the display area. In each case the name of the corresponding status bit is indicated in parenthesis. It will be noted if only a status bit is used (no message).

These messages indicate a condition that may require intervention. They appear in the middle of the display in a framed box. The message will remain until the appropriate intervention has taken place or the condition has been corrected.

ESC, or another message is displayed on the status

34 Chapter 1

Page 35

Instrument Messages

Instrument Messages Introduction

Error Queues

There are two types of error queues, front panel and remote interface. These two queues are viewed and managed separately. Refer to Table 1-1. for more information on the characteristics of the Error Queue.

Front panel A summary of the last 11 error messages preceded by an error number

may be viewed in the Error Queue by pressing, When a remote interface initiates activity that generates an error, the messages are output to the remote bus. When output to the remote interface, they are preceded by an error number.

Remote interface (SCPI) When a user error condition occurs in the analyzer as a result of SCPI

(remote interface) activity, it is reported to both the front panel display error queue and the SCPI error queue. If it is a result of front panel activity, it reports to the front panel display error queue, and depending on the error, may also report to the SCPI error queue.

Table 1-1. Characteristics of the Error Queue

System then Show Errors.

Characteristic

Capacity (number of errors)

Overflow Handling

Viewing Entries

Clearing the Queue

Front-Panel Display

Error Queue

11 30

Circular (rotating). Drops oldest error as new error comes in.

Press:

System, Show Errors, Clear Error Queue

System, Show Errors

SCPI Remote Interface

Error Queue

Linear, first-in/first-out. Replaces newest error with:

−350, Queue overflow

Use SCPI query

SYSTem:ERRor?

Power up. Send a *CLS command. Read last item in the queue.

a. Error history includes the date and time an error last occurred, the error number,

the error message, and the number of times the error occurred.

Instrument Messages

Chapter 1 35

Page 36

Instrument Messages

Instrument Messages Introduction

Error Message Format

The system–defined error numbers are chosen on an enumerated (“1 of N”) basis. The error messages are listed in numerical order according to the error message number. Status and Informational messages without numbers will be listed in alphabetical order following the numerical listing.

In this chapter, an explanation is included with each error to further clarify its meaning. The last error described in each class (for example, –400, –300, –200, –100) is a “generic” error. There are also references to the IEEE Standard 488.2-1992, IEEE Standard Codes, Formats, Protocols and Common Commands for Use with ANSI/IEEE Std 488.1-1987. New York, NY, 1992.

Error messages are displayed at the bottom of the screen in the status line. If you are using the default display colors, the message will appear in green (ESA) or yellow (PSA). The error number is available through the remote interface and the show errors screen; it is not displayed in the status line.

Figure 1-1. Error Message Example

Instrument Messages

36 Chapter 1

Page 37

Instrument Messages

Instrument Messages Introduction

Error Message Types

Events do not generate more than one type of error. For example, an event that generates a query error will not generate a device-specific, execution, or command error.

-499 to -400: Query Errors

-399 to -300: Device-Specific Errors

-299 to -200: Execution Errors

-199 to -100: Command Errors

These errors indicate that the analyzer output queue control has detected a problem with the message exchange protocol described in IEEE 488.2, Chapter 6. Errors in this class set the query error bit (bit 2) in the event status register (IEEE 488.2, section 11.5.1). These errors correspond to message exchange protocol errors described in IEEE 488.2, 6.5. In this case:

• Either an attempt is being made to read data from the output queue when no output is either present or pending, or

• Data in the output queue has been lost.

An error number in the range –399 to –300 indicates that the analyzer has detected an error where some device operations did not properly complete, possibly due to an abnormal hardware or firmware condition. This is not a error in response to a SCPI query or command, or command execution. The occurrence of any error in this class will cause the device-specific error bit (bit 3) in the event status register to be set.

These errors indicate that an error has been detected during analyzer execution.

These errors indicate that the analyzer parser detected an IEEE 488.2 syntax error. Errors in this class set the command error bit (bit 5) in the event status register (IEEE 488.2, section 11.5.1). In this case:

• Either an IEEE 488.2 syntax error has been detected by the parser (a control-to-device message was received that is in violation of the IEEE

488.2 standard. Possible violations include a data element which violates device listening formats or whose type is unacceptable to the device.), or

Instrument Messages

64 to 799: Device-Specific Errors

Greater than 10000: Measurement Applications Errors

• An unrecognized header was received. These include incorrect device-specific headers and incorrect or unimplemented IEEE 488.2 common commands.

These errors indicate that a device operation did not properly complete, possibly due to an abnormal hardware or firmware condition. These codes are also used for self-test response errors. Errors in this class set the device-specific error bit (bit 3) in the event status register (IEEE 488.2, section 11.5.1).

The <error_message> string for a positive error is not part of the SCPI standard. A positive error indicates that the analyzer detected an error within the GPIB system, within the analyzer firmware or hardware, during the transfer of block data, or during calibration.

These errors indicate that an error has been detected while executing measurements requiring a personality option such as the GSM Measurement Personality or those measurements found under the key in SA mode.

Chapter 1 37

MEASURE front-panel

Page 38

Instrument Messages

Error Messages

NOTE Error numbers are displayed in the error queue, not on the display.

To see an error number, press System, Show Errors.

0: No Error

0 No error

The queue is empty. Either every error in the queue has been read, or the queue was cleared by power-on or *CLS.

−499 to −400: Query Errors

NOTE Error numbers are displayed in the error queue, not on the display.

To see an error number, press System, Show Errors.

–440 Query UNTERMINATED after indefinite response

Indicates that a query was received in the same program message after a query requesting an indefinite response was executed (see IEEE 488.2,

6.3.7.5).

–430 Query DEADLOCKED

Indicates that a condition causing a DEADLOCKED query error occurred

Instrument Messages

–420 Query UNTERMINATED

(see IEEE 488.2, 6.3.1.7). For example, both the input buffer and the output buffer are full and the analyzer cannot continue. The analyzer automatically discards output to correct the deadlock.

Indicates that a condition causing an UNTERMINATED query error occurred (see IEEE 488.2, 6.3.2.2). For example, the device was addressed to talk and an incomplete program message was received.

–410 Query INTERRUPTED

Indicates that a condition causing an INTERRUPTED query error occurred (see IEEE 488.2, 6.3.2.7). For example, a query was followed by DAB or GET before a response was completely sent.

38 Chapter 1

Page 39

Instrument Messages

−400 Query Error

This is a generic query error for devices that cannot detect more specific errors. The code indicates only that a query error as defined in IEEE

488.2, 11.5.1.1.7 and 6.3 has occurred.

−399 to −300: Device-Specific Errors

NOTE Error numbers are displayed in the error queue, not on the display.

To see an error number, press System, Show Errors.

−340 Calibration failed

The instrument requires an pressing

System, Alignments, Align All Now.

Align All Now. Restore the alignment by

−330 Self-test failed; EEPROM checksum for <card>

The card identification header for a hardware card is incorrect. If the card is not properly identified, the instrument is likely to be non-functional. Report this error to the nearest Agilent Technologies sales or service office.

−330 Self-test failed; Incompatible Hardware (Third Converter) for E4

(E4447A only) The instrument has detected an incompatible Third Converter board. The upper-most frequency will be limited to 26.5 GHz, but the instrument will otherwise continue to function normally.

−321 Out of memory

An internal operation needed more memory than was available. Report this error to the nearest Agilent Technologies sales or service office.

−310 System error; Pretune DAC Calibration failed

System error; Pretune DAC Cal failed midpoint verification

System error

Instrument Messages

An internal system problem was detected. Report this error to the nearest Agilent Technologies sales or service office.

−300 Device-specific error

This is a generic device-dependent error for devices that cannot detect more specific errors. The code indicates only that a device-dependent error as defined in IEEE 488.2, 11.5.1.1.6 has occurred. Report this error to the nearest Agilent Technologies sales or service office.

Chapter 1 39

Page 40

Instrument Messages

−299 to −200: Execution Errors

NOTE Error numbers are displayed in the error queue, not on the display.

To see an error number, press System, Show Errors.

−253 Corrupt media

A removable media was found to be bad or incorrectly formatted. Any existing data on the media may have been lost.

−250 Mass storage error; EEPROM write timeout on EEPROM

Failure to initialize EEPROM. Report this error to the nearest Agilent Technologies sales or service office.

−241 Hardware missing

Hardware missing; no such SIO address

Missing device hardware. For example, an option is not installed.

−230 Data corrupt or stale

Data corrupt or stale; EEPROM copy of <file>

Data corrupt or stale; NRAM copy of <file>

Possibly invalid data. A new measurement was started but not completed.

−224 Illegal parameter value

You have sent a parameter for this command that is not allowed. See the Function Reference.

−223 Too much data; not all points entered

Too much data; <description of the type of data exceeded>

Indicates that a legal program data element of block, expression, or string

Instrument Messages

type was received that contained more data than the device could handle due to memory or related device-specific requirements.

−222 Data out of range

A legal program data element was parsed but could not be executed because the interpreted value was outside the legal range defined by the device (see IEEE 488.2 11.5.1.1.5). The displayed results may be clipped.

40 Chapter 1

Page 41

−221 Settings conflict;…

…Averaging unavailable when Sig ID is on

When in external mixing, with signal identification on, Averaging Mode is not available as a selection.

…Cannot center unpreselected external mixer

Mixer type is Unpreselected. Preselector centering is not available for unpreselected mixers.

…Command incompatible with band pair marker

Using remote commands, you have tried to adjust the start or stop frequency of a span pair marker. You can adjust only the center and span.

…External mixing unavailable when preamp on

Internal preamp is on and you tried to select external mixing, which is not available.

Instrument Messages

…FFT unavailable when Sig ID is on

When in external mixing, with signal identification on, the Manual FFT function is not available as a selection

…Settings Conflict, Preamp unavailable in external mixing

mode

With external mixing selected, you cannot use the internal preamp.

…Sig ID requires EXTERNAL mixing mode

The Input Mixer setting is set in internal and you tried to select signal identification which is not valid.

…Sig ID unavailable in Manual:FFT

When in external mixing, with FFT on, signal identification is not available as a selection.

…Sig ID unavailable when Averaging is on

When in external mixing, with Averaging Mode on, signal identification is not available as a selection.

…Sig ID unavailable when Signal Track is on

When in external mixing with signal tracking on, signal identification is not available as a selection.

Instrument Messages

Chapter 1 41

Page 42

Instrument Messages

…Signal ID unavailable with Presel Mixer

Signal identification is not available with the preselected mixer selected.

…Signal Track unavailable when Sig ID is on

Signal tracking is not available as a selection when using external mixing with signal identification on.

Settings conflict; parameter currently disabled

This parameter is grayed out (unavailable) in the current context. Check the individual parameter help/documentation for more information.

−200 Execution Error

For devices that cannot detect more specific errors, this code indicates only that an execution error as defined in IEEE 488.2, 11.5.1.1.5 has occurred.

−199 to −100: Command Errors

NOTE Error numbers are displayed in the error queue, not on the display.

To see an error number, press System, Show Errors.

–178 Expression data not allowed

A legal expression data was encountered, but was not allowed by the device at this point in parsing.

–171 Invalid expression

The expression data element was invalid (see IEEE 488.2, 7.7.7.2). For example, unmatched parentheses or an illegal character.

–170 Expression data error

This error, as well as errors –171 through –179, is generated when parsing

Instrument Messages

an expression data element. This particular error message is used if the device cannot detect a more specific error.

–168 Block data not allowed

A legal block data element was encountered, but not allowed by the device at this point in the parsing.

–161 Invalid block data

A block data element was expected, but was invalid (see IEEE 488.2,

7.7.6.2). For example, an END message was received before the end length was satisfied.

42 Chapter 1

Page 43

–160 Block data error

This error, as well as errors –161 through –169, is generated when parsing a block data element. This particular error message is used if the device cannot detect a more specific error.

–158 String data not allowed

A string data element was encountered, but not allowed by the device at this point in the parsing.

–151 Invalid string data

A string data element was expected, but was invalid (see IEEE 488.2,

7.7.5.2). For example, an END message was received before the terminal quote character.

–150 String data error

This error, as well as errors –151 through –159, is generated when parsing a string data element. This particular error message is used if the device cannot detect a more specific error.

Instrument Messages

–148 Character data not allowed

A legal character data element was encountered where prohibited by the device.

–144 Character data too long

The character data element contains more than twelve characters (see IEEE 488.2, 7.7.1.4).

–141 Invalid character data

Either the character data element contains an invalid character or the particular element received is not valid for the header.

–140 Character data error

This error, as well as errors –141 through –149, is generated when parsing a character data element. This particular error message is used if the device cannot detect a more specific error.

–138 Suffix not allowed

A suffix was encountered after a numeric element which does not allow suffixes.

–134 Suffix too long

Instrument Messages

The suffix contained more than twelve characters (see IEEE 488.2,

7.7.3.4).

Chapter 1 43

Page 44

Instrument Messages

–131 Invalid suffix

Attempt to send a SCPI command with a suffix that does not match the current units for the function.

The suffix does not follow the syntax described in IEEE 488.2, 7.7.3.2, or the suffix is inappropriate for this device.

–130 Suffix error

This error, as well as errors –131 through –139, is generated when parsing a suffix. This particular error message is used if the device cannot detect a more specific error.

–128 Numeric data not allowed

A legal numeric data element was received, but the device does not accept one in this position for the header.

–124 Too many digits

The mantissa of a decimal-numeric data element contained more than 255 digits excluding leading zeros (see IEEE 488.2, 7.7.2.4.1).

–123 Exponent too large

The magnitude of an exponent was greater than 32000 (see IEEE 488.2,

7.7.2.4.1).

–121 Invalid character in number

An invalid character for the data type being parsed was encountered. For example, an alpha in a decimal numeric or a “9” in octal data.

−120 Numeric data error; VGR

Numeric data error

This error, and errors −121 through −129, is generated when parsing a data element that appears to be numeric, including non-decimal numeric

Instrument Messages

types. This message is used if the device cannot detect a more specific error.

–114 Header suffix out of range

The value of a header suffix attached to a program mnemonic makes the header invalid.

–113 Undefined header

The header is syntactically correct, but it is undefined for this specific device. For example, *XYZ is not defined for any device.

–112 Program mnemonic too long

The header contains more than twelve characters (see IEEE 488.2,

7.6.1.4.1).

44 Chapter 1

Page 45

–111 Header separator error

A character which is not a legal header separator was encountered while parsing the header.

–110 Command header error

An error was detected in the header. This message is used when the device cannot detect the more specific errors described for errors –111 through –119.

–109 Missing parameter

Fewer parameters were received than required for the header. For example, the *ESE common command requires one parameter, so receiving *ESE is not allowed.

–108 Parameter not allowed

More parameters were received than expected for the header. For example, the *ESE common command only accepts one parameter, so receiving *ESE 0,1 is not allowed.

Instrument Messages

–105 GET not allowed

A Group Execute Trigger was received within a program message (see IEEE 488.2, 7.7). Correct the GPIB controller program so that the GET does not occur within a line of GPIB program code.

–104 Data type error

The parser recognized a data element that is not allowed. For example, numeric or string data was expected, but block data was encountered.

–103 Invalid separator

The parser was expecting a separator and encountered an illegal character. For example, the semicolon was omitted after a program message unit.

–102 Syntax error

An unrecognized command or data type was encountered. For example, a string was received when the device does not accept strings.

–101 Invalid character

A syntactic command contains a character which is invalid for that type. For example, a header containing an ampersand, such as “SETUP&”. This error might be used in place of error numbers –114, –121, –141, and some others.

Instrument Messages

Chapter 1 45

Page 46

Instrument Messages

−100 Command error

This is a generic syntax error for devices that cannot detect more specific errors. The code indicates only that a command error as defined in IEEE 488.2, 11.5.1.1.4 has occurred.

64 to 799: Device-Specific Errors

64 System, Alignments, Align All Now, Needed

102 Excessive 50 MHz RF input power is preventing internal

alignments.

There is too much 50 MHz energy at the RF port for alignments to run. Reduce input power to less than 0 dBm and run alignments again.

103 Sampling Oscillator Unlock; Failure acquiring SO frequency

lock

Report this error to the nearest Agilent Technologies sales or service office.

104 1st LO Unlock; Failure acquiring FracN LO frequency lock

1st LO Unlock; Failure acquiring single loop FracN LO lock

The first LO on has lost phase lock. Report this error to the nearest Agilent Technologies sales or service office.

105 2nd LO Unlock

The second LO has lost phase lock. Report this error to the nearest Agilent Technologies sales or service office.

106 4th LO Unlock

The fourth LO has lost phase lock. Report this error to the nearest Agilent Technologies sales or service office.

Instrument Messages

107 Sample Clock Unlock

Report this error to the nearest Agilent Technologies sales or service office.

108 ESA Cal Oscillator Unlock

Report this error to the nearest Agilent Technologies sales or service office.

108 PSA Parameter not allowed

This error appears when POW:GAIN? is issued with parameters. The POW:GAIN? command to query the state of the preamplifier does not accept parameters.

109 Missing Parameter

A necessary parameter was not provided in the command that was sent.

46 Chapter 1

Page 47

Instrument Messages

129 Meas Uncal

The measurement is uncalibrated, usually due to sweeping a narrow RBW filter too quickly. Check the sweep time, span, and bandwidth settings, or

Auto Couple.

press

143 Final IF Overload

Either increase input attenuation or decrease the input signal level.

163 Freq Count: Reduce Span/RBW ratio

The span is too wide for the current resolution bandwidth. Either reduce the span or increase the RBW.

177 Diagnostic override of Firmware Control; :DIAGnostic:ABUS

Diagnostic override of Firmware Control; :DIAGnostic:AMP

Diagnostic override of Firmware Control; :DIAGnostic:LATCh

Diagnostic override of Firmware Control; :DIAGnostic:MLATCh

Diagnostic override of Firmware Control; :DIAGnostic:REGister:VALue

Diagnostic override of Firmware Control; :DIAGnostic:SBUS

Diagnostic override of Firmware Control; :DIAGnostic:SBUS:DBD

Diagnostic override of Firmware Control; :DIAGnostic:SIO:PARallel

Diagnostic override of Firmware Control; :DIAGnostic:SIO:SERial

187 Directory already exists

190 Unable to save file, invalid path

191 File Operation Status; directory <name> created

File Operation Status; <name> directory deleted

File Operation Status; <name> directory renamed to <name>

File Operation Status; <name> file copied

File Operation Status; <name> file deleted

File Operation Status; <name> file loaded

File Operation Status; <name> file renamed to <name>

File Operation Status; <name> file saved

Instrument Messages

File Operation Status; Volume <name> formatted

196 Can’t Auto-Couple Sweep Time in Zero Span

Chapter 1 47

Page 48

Instrument Messages

197 Marker Freq Count HW Failure

201 Option not installed

The desired operation cannot be performed because a required option is not installed. For example, pressing installed in the ESA analyzer, or issuing a POW:GAIN command without Option 1DS or 110 installed in the PSA analyzer will generate this error.

202 No peak found

Source with no tracking generator

No signal peak was found that meets the criteria under

Search Param Criteria.

Peak Search,

204 ESA only TG Frequency Limit

The tracking generator has reached the limit of its allowable frequency range.

205 Ext Ref

205 Command not recognized

Indicates that the command sent from the remote interface was not recognized. Check the programming guide for correct syntax.

206 Unable to initialize flatness data

A failure occurred in setting the flatness data in the internal EEROM. Get in touch with your local Agilent Technologies sales and service office.

207 Unable to store flatness data

A failure occurred in setting the flatness data in the internal EEROM. Get in touch with your local Agilent Technologies sales and service office.

208 Preselector is not available at this frequency.

A preselector is available, but the marker is at a frequency which does not support preselection (~<3 GHz). Preselector centering can be performed

Instrument Messages

only for frequencies above 3.025 GHz.

209 Preselector centering failed

An attempt to center the preselector failed. You tried to center the preselector with the analyzer span too wide. Preselector centering can be performed only for spans below 1.123 GHz.

211 RBW limited to 1 kHz when Span > 5 MHz

In spans greater than 5 MHz, narrow (digital) resolution bandwidths, below 1 kHz, are not available.

213 Span limited to 5 MHz when RBW < 1 kHz

In narrow (digital) resolution bandwidths, below 1 kHz, spans greater than 5 MHz are not available.

48 Chapter 1

Page 49

214 ESA only TG start freq is less than 9 kHz

Tracking generator uncalibrated below 9 kHz.

215 ESA only TG start freq is less than 1/2 res bw

Tracking generator uncalibrated at start frequencies below 1/2 the current resolution bandwidth.

216 Invalid Baud Rate

Attempt to use invalid baud rate. Refer to the programming language chapter of Agilent Technologies ESA Series Spectrum Analyzer Programmer’s Guide for more information.

217 RS-232 Interface Error

An error occurred on the serial interface.

219 Command not valid in this model

Indicates that the command sent from the remote interface does not apply to this analyzer model number. For example, attempting to center the preselector in an analyzer without a preselector will generate this error.

Instrument Messages

220 Trace Menu is unavailable when Sig Ident is ON

221 Invalid option, unable to uninstall package

You have attempted to remove a personality that is not currently installed. Verify command was entered correctly.

222 Command not valid when no measurement is active

Indicates that the command sent from the remote interface must be issued while a measurement is running in the analyzer.

223 Neg. Trig Delay unavailable in Swept Mode, zero delay used.

Trigger Offset unavailable in swept spans

Trigger Offset is only available in Zero Span. Refer to “Trig” in your Agilent Spectrum Analyzer User’s Guide for a description of this function.

224 Option not licensed.

The selected option requires a license. Refer to the installation procedures in the user guide provided for this particular option.

226 Actual Trig Delay = Remote Trig Delay + Remote Trig Offset

228 Preselector centering failed - inadequate peak

Instrument Messages

The signal on which the marker is placed is not a high enough level peak for centering the preselector. This can be the result of pressing

Center

without first turning off the marker. You may have left the marker

Presel

on and placed below the signal peak or in the noise.

Chapter 1 49

Page 50

Instrument Messages

229 3 − 26.5 GHz preselector bypassed, can’t adjust

The microwave preselector has been bypassed so it cannot be centered or adjusted. Pressing the key or send the SCPI commands for

Presel Adjust will result in this error.

Presel Center or

230 Unpreselected external mixing - no preselector

If you are using an unpreselected mixer while doing external mixing then there is no preselector to center or adjust. Pressing the key or sending the SCPI commands for

Presel Center or Presel Adjust will result in this error.

231 Preselector unavailable while in external mixing

The internal preselectors cannot be used while in external mixing.

232 External mixing is off, can’t adjust external preselector

External mixing is turned off so the external mixer preselector is not available.

235 PSA 26.5 - 50 GHz preselector bypassed, can’t adjust

The millimeter wave preselector has been bypassed so it cannot be centered or adjusted. Pressing the key or send the SCPI commands for

Presel Center or Presel Adjust will result in this error.

236 PSA License conflict: Options X and Y can not be licensed at same

time

This error is generated if you attempt to license two incompatible options together in the analyzer. For example, Options 115 and 117 are incompatible and will generate this error if both are licensed. The “X” and “Y” in this message are replaced with the actual options.

238 Trace smoothing: VBW filt or Average Detector; cannot use both

239 HW Diag is OFF

249 AC Coupled

Instrument Messages

332 Average Type incompatible for scale.

Amplitude Scale command should be sent prior to the Average Type command.

601 PSA only 612 ESA only File not found

The analyzer could not find the specified file.

601 Floppy disk full

The floppy disk is full. Clear some space by deleting unwanted files.

50 Chapter 1

Page 51

602 PSA only 605 ESA only Media is protected

A save was attempted to a write-protected device.

602 Floppy disk error

An unknown error has occurred while accessing the floppy disk.

603 PSA only 615 ESA only File is corrupt

Corrupted file

The file that you were trying to load is corrupt.

604 PSA only 607 ESA only File name error

File name error; Directory does not have a default file type

File name error; Directory does not support extenders

File name error; Empty filename

Instrument Messages

File name error; Illegal extender

File name error; Illegal filename character

File name error; Only one: is allowed

File name error; Only one extender character allowed

An invalid file name was specified. Use filenames with a maximum of 8 characters (letters and digits only), and use a 3-character extension. File names are not case-sensitive. This error also occurs if you try to delete a nonexistent file.

615 PSA only 604 ESA only File exists

File already exists

You attempted to save to a file that already exists. Either delete or rename the existing file or select a new name, then try again.

602 PSA only 605 ESA only Media is protected

A save was attempted to a write-protected device.

Instrument Messages

Chapter 1 51

Page 52

Instrument Messages

605 Data corrupt or stale; EEPROM copy of <file>

WAR NING: Contact the factory if you see this error.

This error indicates that a file stored in EEPROM has become corrupt and the Hamming codes are unable to repair the data.

When the EEPROM file has been corrupted, the system will store default values into both the Non-Volatile RAM and EEPROM copies of the file. If this error occurs often, it may indicate that there is a problem with the physical memory.

Data corrupt or stale; RAM copy of <file>

This error indicates that a file stored in Non-Volatile RAM has become corrupt and the Hamming codes are unable to repair the data.

When a Non-Volatile file has this error, the system will first try to verify the state of the data in EEPROM and if valid it will copy the data in EEPROM into the Non-Volatile ram copy of the file. When this happens, the system will remain calibrated. If this error occurs often, it may indicate that there is a problem with the physical memory.

606 Data questionable; EEPROM copy of <file>

EEPROM error occurred. The EEPROM copy of an internal file is either corrupt or otherwise unusable. The system automatically updates the non-volatile RAM copy of the EEPROM copy using a default initialization. The actual EEPROM file is left as it is. Report this error to the nearest Agilent Technologies sales or service office.

606 Media is corrupt

A save was attempted to a corrupt device.

604 PSA only 607 ESA only File name error

File name error; Directory does not have a default file type

Instrument Messages

File name error; Directory does not support extenders

File name error; Empty filename

File name error; Illegal extender

File name error; Illegal filename character

File name error; Only one: is allowed

File name error; Only one extender character allowed

608 Mass storage error; EEPROM write timeout

52 Chapter 1

Page 53

609 Restoration of NVRAM data

This error indicates that a file stored in Non-Volatile RAM has been corrected based on the Hamming codes stored with the file. After the correction, the file will contain the same data as when the instrument was shut off. If this error continues to occur on successive power cycles, it may indicate that there is a problem with the physical memory.

627 PSA only 609 ESA only Media is not writable

A save was attempted to a read-only device or device that could not be written to. Try a known-good disk.

610 File access is denied

The file is protected or hidden and cannot be accessed.

611 File access IO busy;

duplicate :SERVice[:PRODuction]:CALibrate:BEGin

File access IO busy; :SERVice[:PRODuction]:CALibrate:END without a BEGin

Instrument Messages

601 PSA only 612 ESA only File not found

The analyzer could not find the specified file.

613 Flash memory is full

The internal flash memory is full. Clear some space by deleting unwanted files. If your analyzer has a serial number less than US41440000 or MY41440000 and Option B72 has not been installed, you may also increase the flash memory size by purchasing Option B72.

763 PSA only 614 ESA only Bad, missing, or unformatted disk

Bad or missing floppy disk

The floppy disk is not inserted properly, is not formatted, or the directory cannot be read. Insert a known good disk and try again.

615 PSA only 604 ESA only File already exists

File exists

You attempted to save to a file that already exists. Either delete or rename the existing file or select a new name, then try again.

Instrument Messages

Chapter 1 53

Page 54

Instrument Messages

603 PSA only 615 ESA only File is corrupt

Corrupted file

The file that you were trying to load is corrupt.

617 Wrong density floppy inserted

The floppy disk has the wrong density. It should be 1.44 MB.

618 Illegal write access of Flash memory

Attempt to write to an unavailable area of internal flash memory.

619 Can’t Auto-Couple RBW in Zero Span

You sent a remote command to set the RBW into auto while in zero span.

620 Can’t Auto-Couple Sweep Time in Zero Span

You sent a remote command to set the sweep time to auto while in zero span.

622 External reference missing or out of range

The external frequency reference signal is missing, has too low an amplitude, or does not match the frequency value that you previously entered into instrument memory.

623 Printer not responding

Printer not responding; ioctl ERROR

Check the printer. It may not be connected properly or turned on.

625 Printer out of paper

Load paper in printer.

626 Print failed; Can’t open print file desc

Instrument Messages

Print failed; DisplayExport can’t create print file

Print failed; DisplayExport illegal print language

Print failed; DisplayExport insufficient RAM space

Print failed; DisplayExport undetermined error

Print failed; Error transferring image to printer

Print failed; Printer ioctl failed

Print failed; Unknown printer response

54 Chapter 1

Page 55

Instrument Messages

627 PSA only 609 ESA only Media is not writable

A save was attempted to a read-only device or device that could not be written to. Try a known-good disk.

ERROR/NUMBER “609 Restoration of NVRAM data” IS ALREADY USED FOR HAPPENING ./storage/directory/NRAM_Directory.cc HAP_nramDataCorrected

651 Connect RF OUT to INPUT

Attempt to align the tracking generator without its output connected. Connect the tracking generator RF OUT to the analyzer

INPUT.

652 Connect Amptd Ref Output to Input

For Agilent Technologies E4402B, E4403B, E4404B, E4405B, E4407B, and E4408B only: you must connect the

INPUT with the appropriate cable.

AMPTD REF OUTPUT to the analyzer

653 Auto Align not available when using Calibration Defaults

The Auto Alignment system cannot be used until an executed by pressing

System, Alignments, Align Now, All. On all Agilent

Technologies ESA spectrum analyzer models except Agilent Technologies E4401B and E4411B, you must connect the with the appropriate cable to perform this alignment. For Agilent Technologies E4401B and E4411B only: disconnect any signals from the

INPUT prior to performing this procedure.

701 Invalid printer response

In attempting to identify the printer an invalid response was received. Check that you are using a supported printer. Be sure you are using the proper cable and that it is securely fastened.

702 Unsupported printer

A printer which is recognized, but known to be unsupported was identified. This printer cannot be used with the analyzer. For example, a printer only supported by Microsoft Windows will generate this error.

703 Unknown printer

In attempting to identify the printer, a valid response was received but the printer is not known to the analyzer. Use the

Print Setup to configure the printer.

Align Now All is

AMPTD REF OUT to the INPUT

Instrument Messages

Custom printer menu under

704 Printer interface error

An error occurred while trying to print. Make sure the printer is turned on and properly connected.

Chapter 1 55

Page 56

Instrument Messages

705 Printer Type is None

The current printer type is set to Change the type in the

Print Setup menu and try again.

None, so no print operations are possible.

727 In <filename>: [DATA] header missing

This message indicates that the data section of a file did not begin with the token [

DATA].

728 In <filename>, line <nnn>: separator missing

The [HEADER] section of a file contains entries requiring an equal (=) sign, such as <keyword> = <value>. This message appears if the equal sign does not appear on the line.

729 In <filename>: error reading file

Appears when loading data from a limit line or corrections disk file and a failure to the file occurs.

730 In <filename>, line <numeric_value>: line too long

When loading data from a limit line or corrections disk file, this message will appear if the length of any line in the file exceeds 255 characters.

731 In <command>: bad data count (<numeric_value>): expected

multiple of <numeric_value>

This message indicates that the data sent to a corrections or limit table via the

DATA or MERGE commands does not have the expected length for the

table. For example, this message would appear if an attempt were made to merge 7 numeric values into a limit table, since each logical entry requires 3 values (frequency, amplitude, and connected).

732 In <filename>, line <numeric_value>: error parsing tokens

This message may appear when loading data from a limit line or corrections disk file. It indicates a problem in the attempt to break a string

Instrument Messages

of text into tokens. There may be too few tokens in the string. In other words, the file content must match the expected format. This typically happens when there are too few numeric values in the [

DATA] section of a

limit or corrections file.

733 In <filename>, line <numeric_value>: <xxx> is not numeric

This message may appear when loading data from a limit line or corrections disk file. It indicates that a non-numeric token <xxx> was found where a numeric token was expected. In other words, the file content must match the expected format.

56 Chapter 1

Page 57

734 Interpolation error: cannot compute log of

<negative_frequency_value>

Occurs when the frequency interpolation of a limit line is set to log and the start frequency of the instrument is negative. The <negative_frequency_value> is limited to – 80 MHz, so it may not match the frequency that caused the error.

735 In <filename>: bad amplitude unit <unit>

This message indicates that unit <unit> is not recognized or supported.

736 Too many data values at <freq_or_time_value>

This message may appear when data is sent to a corrections or limit table using the

DATA or MERGE commands. These tables limit the number of

amplitudes associated with a frequency or time to 2 or less. This message will appear if an attempt is made to attach 3 or more values to a frequency or time.

751 Instrument state set to initial values

Instrument state may be corrupt, state has been reset to initial values

Instrument Messages

While trying to load a trace or state, the state information was found to be in error. This may be because the state had been stored on a later revision of analyzer firmware. A default set of state variables was loaded instead. There is nothing wrong with the analyzer.

An error in the internal instrument state has been detected. The state has been reset to a default value.

752 Unable to load state from file

Attempt to load a state from a file failed.

753 Unable to save state to file

Attempt to save a state to a file failed. See the associated error messages for the cause (press

System, Show Errors).

For PSA: If this error occurs after a mode switch that takes longer then normal, you may need to free up some instrument memory. When you switch to a different measurement mode, the analyzer must temporarily store instrument state data. If you have less then 500 kB of available memory, the switching process can take over 1 minute and result in this error. Use the File key menu to delete any unnecessary files from instrument memory.

755 Unable to load state from register

Instrument Messages

Attempt to load a state from an internal state register failed.

Chapter 1 57

Page 58

Instrument Messages

756 Unable to save state to register

Attempt to save a state to an internal state register failed. See the associated error messages for the cause (press

System, Show Errors).

757 Unable to load user state, factory preset was done

A user preset failed, so the factory preset values were used. Save a valid state into user preset and try again.

758 Unable to save user state

Attempt to save a user preset state failed. See the associated error messages for the cause (press

System, Show Errors).

759 Unable to load state saved from firmware Rev A.xx.xx; Restore

Sys\nDefaults

Unable to load state

A saved state file from a newer firmware revision was attempted to be loaded into an older instrument.

760 ESA only Unable to query state

Query of state over the remote interface was unsuccessful.

761 ESA only Unable to set state

Attempt to set the state over the remote interface was unsuccessful.

762 ESA only Incorrect filename, allowable extensions are .trc or .csv

Attempt to save a trace to a file with an incorrect extension.

762 ESA only Unable to load file

A failure occurred while loading a file; the file was not loaded.

763 PSA only 614 ESA only Bad, missing, or unformatted disk

Instrument Messages

Bad or missing floppy disk

The floppy disk is not inserted properly, is not formatted, or the directory cannot be read. Insert a known good disk and try again.

763 ESA only Incorrect filename, allowable extensions are .gif or .wmf

Attempt to save a screen image to a file with an incorrect extension.

764 Unable to save file

Attempt to save a file failed; the file was not saved. See the associated error messages for the cause (press

58 Chapter 1

System, Show Errors).

Page 59

Instrument Messages

765 Unable to load file

Attempt to load a file failed; the file was not loaded.

766 Unable to format drive

767 Failed to Initialize ISTATE regions. Fatal LDS error

Attempt to initialize the instrument state has failed. Cycle instrument power. If this fails to correct the problem, contact your nearest Agilent Technologies service center.

768 Unable to load user state, required instrument mode is not

installed

Attempt to load a state failed, because the state was saved with a measurement personality that is not currently loaded. Load the appropriate personality and try again.

769 ESA only Invalid instrument mode

You have attempted to switch to an instrument mode that is currently not installed. Confirm that the mode name (for INST:SEL) or number (for INST:NSEL) was entered correctly and that the requested personality is actually installed in the instrument.

770 Incorrect filename, allowable extensions are .gif or .wmf

You sent a remote command to save a screen file but did not specify a valid extension.

Incorrect filename, allowable extension is .sta

You sent a remote command to save a state file but did not specify a valid extension.

Incorrect filename, allowable extensions are .trc or .csv

You sent a remote command to save a trace file but did not specify a valid extension.

770 Instrument mode requested is not supported

Instrument mode specified with: INST command is not valid. Refer to programming information.

771 Store Ref trace before turning on Normalize

Attempt to turn on Normalize with trace 3 being at the noise floor (PSA). A reference trace must be available for the Normalize function to be activated. Refer to “View/Trace” in the Agilent ESA Spectrum Analyzer User’s Guide where the

Normalize key function is explained in detail.

Instrument Messages

Chapter 1 59

Page 60

Instrument Messages

772 Cannot load a directory

Cannot load a directory, please choose a file

You have selected a directory instead of a file when attempting to perform the Load function under the

File front-panel key.

773 Linear units unavailable with Normalize on

Attempt to change amplitude units to an absolute unit which is not allowed with Normalize.

774 Linear scale unavailable with Normalize on

Attempt to change Scale Type to LIN which is not allowed with Normalize.

780 No Peak Found

No signal peak was found that meets the criteria under

Search Param Criteria.

Peak Search,

781 Video Trigger cannot be active with Average Detector

You sent a remote command to do one of the following:

• Turn on video trigger while the Average Detector or a Marker Function is active.

• Turn on the Average Detector or a Marker Function while Video Trigger is active.

782 Video Trigger cannot be used with Mkr Func due to Average

Detector

783 Allowable span for current center frequency exceeded

When rotating the knob or step up/down keys to change the Span, the value of the Center frequency is kept constant. Therefor, the span is limited by the frequency range of the instrument.

Instrument Messages

784 Allowable CF for current span exceeded

When rotating the knob or step up/down keys to change the Center frequency, the value of the Span is kept constant. Therefor, the center frequency is limited by the frequency range of the instrument.

786 Cal file not initialized correctly, <filenumber>

This indicates that an older LO board is loaded in, with uninitialized values for the milli-meter band edges in it's EEPROM band edge cal file. This happening is will therefore only be visible in the service mode.

60 Chapter 1

Page 61

787 WBIF Self Test Failed

Option 122 or 140 performs a loop-back self-test on power up. It does an ADC image calibration, then stores a sine wave in RAM and plays it out the DAC. It then measures the carrier power, image rejection and signal-to-noise ratio. If this test fails, the wideband digitizer hardware is either incorrectly installed or has a hardware failure. Call your Agilent Service representative.

There is diagnostic information available. The self test can be run with DIAG:WBIF:TEST? This command returns 4 values: passed, carrier power, image rejection and signal to noise ratio.

First look at the carrier power. If it is below –50, the LVDS cable is probably missing or faulty. If the carrier power is above 0 dBm, image rejection less than 40 but SNR more than 50, there is probably a bad ADC.

788 WBIF ADC Image Calibration Failed

The wideband digitizer hardware uses two ADC's that must be kept in perfect synchronization to avoid unwanted images appearing in the spectrum. The instrument will occasionally perform an ADC Image Calibration (formerly known as Step Cal) to resynchronize the ADC's. This calibration is only known to fail if there is a hardware problem.

Instrument Messages

789 WBIF Firmware Reset

The wideband digitizer hardware has a local microprocessor controlling the hardware trigger. If this microprocessor resets, it will automatically restart and begin taking data again, and will send this error message. While this should never happen, it is a self-recovering error that requires no action on the part of the user. If, however, it starts to occur frequently, contact your Agilent service representative to find out if there is a firmware upgrade to solve the problem.

791 Acquiring Data...

WBIF Power On Test Failed

An error occurred when the wide bandwidth IF hardware (Option 122 or

140) was tested during the power on process.

795 No trigger before timeout; auto-triggered

797 Awaiting Trigger, no AUTO Trig

801 Memory limit caused Data Acquisition to be truncated

805 doing Alignment...

838 Log Frequency Interpolation not Implemented

Instrument Messages

This error message is displayed when you try to load a correction file that is using logarithmic frequency interpolation.

Chapter 1 61

Page 62

Instrument Messages

Greater than 10000: Measurement Applications Errors

NOTE Error numbers are displayed in the error queue, not on the display.

To see an error number, press System, Show Errors.

10008 to 10522: Power Suite Error Messages An error number in this range indicates the instrument has detected an error relating to the Power Suite functionality.

10008 Preferred resolution bandwidth not available.

The calculated required resolution bandwidth for this measurement is not available.

10010 One or more harmonics past freq limit: number decreased.

Highest harmonic was past the frequency limit of the analyzer, so the number of measured harmonics was decreased.

10011 First harmonic is past analyzer frequency limit.

First harmonic was past the frequency limit, so no harmonics can be measured. The analyzer will simply measure the fundamental. If you have an Option AYZ it allows the use of Agilent 11970 Series, and Agilent 11974 external mixers to extend the frequency range to 110 GHz. Operation to 325 GHz is also possible with non-Agilent mixers.

10012 No Fundamental > 0 Hz found in given span.

There were no frequencies greater than 0 Hz in the starting span, so the centre frequency at measurement entry will be used as the fundamental.

10013 No Fundamental > -50 dBm found in given span.

There was no fundamental found, so the centre frequency at measurement entry will be used as the fundamental.

Instrument Messages

10020 Signal Tracking is not available when Noise Correction is on.

If signal tracking is turned on while noise correction is on, it will be turned off. To use the signal tracking function, first turn noise correction off.

10138 Valid GSM burst not found in frame (Burst Type)

No active GSM bursts that match the selected burst type have been detected in the RF input signal. Search was performed over a complete GSM frame.

10139 Valid GSM burst not found in specified timeslot (Burst Type)

No active GSM bursts that match the selected burst type have been detected in the RF input signal. Search was performed over the specified timeslot.

62 Chapter 1

Page 63

Instrument Messages

10140 Valid GSM burst not found in frame (Ref Burst)

No active GSM bursts that match the selected burst type have been detected in the RF input signal. Search was performed over the specified complete GSM frame using the Ref Burst type setting.

10141 Sync word not found in frame (Burst Type)

One or more active GSM bursts that match the selected burst type have been detected in the RF input signal, but none contain the selected Training Sequence Code (TSC). The search was performed over the complete GSM frame.

10142 Sync word not found in specified timeslot (Burst Type)

10143 Sync word not found in frame (Ref Burst)

10144 Unknown demod status

Demodulation is in an unknown state. Press

Preset. If the error persists,

get in touch with your service center.

10145 Opt AYX hardware required. Meas unavailable.

Option AYX must be installed for this measurement to be enabled.

10146 Options B7D & B7E hardware required. Meas unavailable.

The RF Communications Hardware (Option B7E) and Digital Signal Fast ADC (Option B7D) cards required to perform the demodulation are not present in the analyzer.

10147 Opt B7D bootrom requires upgrade.

The (Option B7D) bootrom revision is not supported by the currently loaded personality version. Refer to the user’s guide for the personality in use.

10148 Opt BAH DSP algorithm files not installed. Meas unavailable.

Contact your Service Center.

The Digital Signal Processor algorithm files required to perform the demodulation are not present in the analyzer.

Instrument Messages

Chapter 1 63

Page 64

Instrument Messages

10148 B7D DSP Code Fail. Reload Opt BAH. Contact your Service

Center.

The Digital Signal Processor algorithm files required to perform the demodulation are not present in the IDSP: drive.

10149 Opt BAH DSP algorithm code file requires upgrade.

The Digital Signal Processing algorithm code file revision is not supported by the currently loaded personality version. Refer to the user guide for the personality in use for more information on installation/upgrade.

10150 Opt BAH DSP algorithm coef. file requires upgrade.

The Digital Signal Processor algorithm coefficient file revision is not supported by the currently loaded personality version. Refer to the user guide for the personality in use.

10151 Opt BAH DSP algorithm files failed to load, aborting measure.

The Digital Signal Processor algorithm files required to perform the demodulation are corrupt and cannot be loaded properly. Reinstall measurement personality.

10151 B7D DSP Code Fail. Reload Opt BAH. Contact your Service

Center.

The Digital Signal Processor algorithm files required to perform the demodulation are present in the IDSP: drive and cannot be loaded properly into DSP RAM. Reinstall measurement personality.

10152 Lost trigger, aborting measurement.

The selected trigger source was present at the start of the measurement, but timed out before the measurement completed.

10153 DSP algorithm timeout, aborting measurement

The Digital Signal Processor demodulation algorithm timed-out for an

Instrument Messages

unknown reason. This message normally indicates a problem with the modulated signal.

10154 Measurement not defined for Out of Band.

You have changed to an out-of-band frequency range. The band measurement only operates in the selected band.

10155 No Fast ADC hardware installed. Meas unavailable.

The analyzer cannot use sweep times of less than 5 msec when Option B7D or Option AYX is not installed. Therefore, the measurement will not be executed.

64 Chapter 1

Page 65

Instrument Messages

10156 No Fast ADC hardware installed.

The analyzer cannot use sweep times of less than 5 msec when Option B7D or Option AYX is not installed resulting in all the radio standards not being supported.

10156 The calibration data is invalid, and has been cleared.

10157 Tracking Generator hardware is not present. Meas unavailable.

The measurement requires a built-in tracking generator.

10158 This operation requires a measurement to be active.

10159 Entire trace is below threshold level

The measurement cannot operate properly because the trace has completely fallen below the threshold level. Change the threshold level to view trace.

10160 Valid burst not found

Cannot find a valid burst, either because it is not fully on the display, or the level is too low to be detected properly.

10160 Upper Custom Mask is Invalid!

The user-specified upper custom mask cannot be resolved into a limit line. The format may be bad.

10161 No Fast ADC hardware installed.

Cannot use sweep times less than 5 ms, due to the lack of a fadc, therefore the meas will be severely restricted.

10161 Lower Custom Mask is Invalid!

The user-specified lower custom mask cannot be resolved into a limit line. The format may be bad.

10162 Resolution BW <300 kHz.

This error message is a warning that the resolution bandwidth has been set below 300 kHz. The test results will not meet GSM specifications.

10163 Cannot find the Power vs Time Limits File.

The limit line definition file for the GSM standards has been deleted. This message is displayed while the

Measure key is grayed out. Reinstall the

GSM measurement personality.

10164 Band Measurement not defined for Out of Band.

Instrument Messages

You are attempting to monitor the band but have set the frequency outside the band. Reset the band for the particular standard for which you are testing or use the channel setting which does not require a frequency to be set. (

Meas Setup, Method (Channel)).

Chapter 1 65

Page 66

Instrument Messages

10165 Carrier Not Present.

10166 Cannot update the list of cable types.

The cable file may have been moved or deleted accidentally. Reinstall the measurement personality. This message is applicable to the GSM (Option BAH) and Distance to Fault (Option 225) measurement personality options.

10166 Cannot locate the file that contains the list of cable types.

10167 The file containing the list of cable types has been updated.

10168 Cannot update the list of cable types on drive C:

The file update failed.

10170 The Cable Fault Measurement is active. Mode Setup is disabled.

Mode setup is not available in the cable fault utility.

10172 Sweep Time too fast (<2 sec)

The sweep time must be set to 2 seconds or longer for the results to be valid.

10173 Carrier Not Present.

10177 There are no spurs to inspect.

You have attempted to switch the

Inspect Spur menu key to the On position

after the measurement has finished, but found no spurs.

10178 Carrier Not Present.

10179 Carrier Present. Test Stopped!

Instrument Messages

A carrier was found in the transmit band. Either disable the carrier or insert a bandpass filter for the receive bandwidth.

10180 Gate option not installed. Results may not be accurate.

This measurement method requires the use of the time-gate (option 1D6) in order to gate the spectrum during the 50-90% part of the burst. If the gate option is not installed, the measurement will still run although this warning will be displayed.

10181 Upper Custom Mask is Invalid!

The user-specified upper custom mask cannot be resolved into a limit line. The format may be bad.

66 Chapter 1

Page 67

Instrument Messages

10182 Lower Custom Mask is Invalid!

The user-specified lower custom mask cannot be resolved into a limit line. The format may be bad.

10183 Resolution BW < 300kHz.

The test will not meet EDGE specifications because the resolution BW has fallen below 300 kHz.

10184 Cannot find the Power vs Time Limits File.

Cannot find the limit line definition file for the EDGE standards. This message is displayed while the

Measure key is grayed out.

10185 Gate option not installed. Results may not be accurate.

10186 Measurement does not support the current radio standard.

The measurement you have chosen is currently greyed out. Select a radio standard which is supported or configure this measurement manually (

Mode Setup, Radio Std. None).

10186 EDGE EVM only supports EDGE TCH burst type (Burst Type)

10187 Radio standard is not supported by the current measurement.

The standard you have chosen is currently greyed out. Select a radio standard which is supported by the current measurement or configure this measurement manually (

Mode Setup, Radio Std. None).

10187 EDGE ORFS only supports EDGE TCH burst type (Burst Type)

10188 EDGE PVT only supports EDGE TCH burst type (Burst Type)

10189 EDGE PVT only supports EDGE TCH burst type (Ref Burst)

10190 Select a valid Radio Standard/Measurement combination to

enable.

The Enable All Measurements menu key was pressed when it was disabled. To enable select a radio standard that is supported by the current measurement or a measurement that supports the current radio standard.

10190 EDGE ORFS only supports EDGE TCH burst type (Ref Burst)

10191 Mask unavailable for current Span - increase to display mask.

The current span setting is either narrower than the mask width or so wide that there are too few display points to allow the mask to be drawn. Increase or decrease the span to display the mask.

Instrument Messages

10191 EDGE EVM only supports EDGE TCH burst type (Ref Burst)

Chapter 1 67

Page 68

Instrument Messages

10192 Sweep Point/Span ratio below minimum - results may be

inaccurate.

The sweep point to span ratio is below the minimum required to ensure the bucket ratio is large enough to test DVB-T masks

10218 Hardkeys are disabled.

Some of the forms (for example Receiver Spurious in GSM) do not allow you to close the form without either formally accepting or cancelling the form settings. For this reason, all of the hardkeys are disabled until you terminate the form.

10219 Awaiting trigger

The measurement requires a trigger to be present. If the trigger does not occur or is delayed, this message will be displayed. Check your trigger settings.

10220 Preselector cannot be bypassed in this mode.

The Option 123 allows the microwave preselector to be bypassed. This functionality is not available from within either the Phase Noise or Noise Figure application modes. If the preselector is set to off, it will immediately be forced back to On.

10227 Measurement suspended until carrier is turned off.

The receive channel power and the receive spur measurements are specified with the attenuation set to 0 dB. To prevent overload, the frequency spectrum of interest is monitored for signal levels which exceed a specified threshold before setting the attenuator to 0 dB. If a carrier is found, this message is displayed and the completion of the measurement will not occur until the carrier is removed. The carrier check may be turned off using the properties form under the front-panel

Mode Setup key.

You may also change the signal threshold which determines a carrier on the properties form.

Instrument Messages

10228 Cannot correlate to input signal.

This error is normally generated because of one of the following reasons:

1. There is no carrier signal.

2. Walsh channels other than the pilot are active.

3. There is some other modulation problem that will prevent the

measurement from being made. This problem must be corrected before the measurement can continue.

10229 The regression portion failed.

This message occurs when (Option B7D) is not functioning properly. Demodulation measurements (modulation accuracy and code domain) might fail as a result of this error.

68 Chapter 1

Page 69

10230 DSP timed out, resetting DSP.

Digital Signal Processor was unable to finish the selected measurement within the given period of time. Restart the measurement.

10231 Measurement failed for unknown reasons.

Check instrument settings and restart measurement.

10232 RF Signal not found.

This message is generated if there is no signal at the center frequency that is greater than 10 dB above the displayed average noise level.

10233 Level is low, results may degrade.

The signal being measured is of low power. The results may not be as accurate as they would be if the signal level was higher.

10237 RF Board LO Unlocked. Contact service center.

This message occurs if the local oscillator on the (Option B7E) is in an unlocked state. This indicates broken hardware.

Instrument Messages

10238 RF Board SR Osc Unlocked. Contact service center.

This message occurs if the sample rate (SR) oscillator on Option B7E is in an unlocked state. This indicates broken hardware.

10239 Opt Freq Ref setting does not match external reference.

This message is generated if Source is set to External on the properties form under the front-panel

Mode Setup key and the frequency on the same

form is set to a frequency that does not match the frequency of the signal being used as the external reference.

10240 RF Board RF Osc Unlocked. Contact service center.

This message occurs if the reference oscillator on the (Option B7E) is in an unlocked state. This indicates broken hardware.

10241 RF Board could not detect any bursts in signal.

This message is generated when the trigger is set to RF Burst and (Option B7E) cannot detect a burst.

10245 Error reading file: SPCLIMIT.CSV. Cannot use custom limits.

The file could be missing or corrupt. Create a new limits file. Alternatively, the actual limits defined in the file might not allow the measurement to be executed. Redefine the limits or use the default limits. Restart the measurement.

Instrument Messages

10246 Error reading file: CDMASTUN.CSV. Please reinstall cdmaOne.

The file is missing or corrupt. Please reinstall the cdmaOne personality.

Chapter 1 69

Page 70

Instrument Messages

10247 Error reading file: CDPDMDA. Please reinstall cdmaOne.

The file is missing or corrupt. Please reinstall the cdmaOne personality.

10248 Error reading file: CDPPMCO. Please reinstall cdmaOne.

The file is missing or corrupt. Please reinstall the cdmaOne personality.

10249 Error reading file: CDPPMDA. Please reinstall cdmaOne.

The file is missing or corrupt. Please reinstall the cdmaOne personality.

10250 Error reading file: RHODMDA. Please reinstall cdmaOne.

The file is missing or corrupt. Please reinstall the cdmaOne personality.

10251 Error reading file: RHOPMCO. Please reinstall cdmaOne.

The file is missing or corrupt. Please reinstall the cdmaOne personality.

10256 Error reading file: OOBSTAB.CSV. Use Edit Table | Save Table.

This error is generated when you try to load a table (using the

Load Table

key on page 2 of the edit table form menu) before a table has been saved. You must first save a table using the table using the

Load Table key.

Save Table key before trying to load a

10259 Table could not be saved.

This message occurs if the C: drive is full or corrupt. Check the amount of space left on the drive.

10260 Table could not be loaded.

When trying to load a table, the previous table has been somehow corrupted. Use the

Save Table key to save a valid table. Then edit the valid

table, save it, and try to load it again.

10264 Emission bandwidth not found. Consider increasing span.

This error is normally generated when attempting occupied bandwidth

Instrument Messages

measurements. The “X dB” value you entered (

Meas Setup, X dB) to

calculate the emission bandwidth is the difference between the highest point on the trace and the point “X dB” down on either side of the maximum. If the actual difference is less than the value entered, the emission bandwidth cannot be computed. Some responses to this situation are as follows:

1. Connect a signal to the input. (If there is no signal present, the difference between the trace minimum and maximum will generally be less than “X dB”.)

2. Increase the span. (If the signal is wide, the shoulders of the signal might not be present on the screen, and again, the difference between the trace minimum and maximum will be less than “X dB”.)

70 Chapter 1

Page 71

Instrument Messages

3. Center the signal. (There must be a point on the trace that is “X dB” down from the maximum on both sides of that maximum.)

10286 Burst not found.

Either the signal being analyzed has insufficient power, the rising or falling edges cannot be detected, or the burst is less than 126 microseconds.

10287 Valid Bluetooth burst not found. (Check Packet Type)

The burst that has been found does not correspond to the currently selected Bluetooth packet type (the burst length may be too short).

10288 Option B7D or AYX FADC hardware required. Meas unavailable.

The measurement you are attempting requires either the DSP and Fast ADC (Option B7D) or the Fast ADC (Option AYX) card to perform the demodulation, but neither are present in the analyzer.

10289 Opt 106 demod hardware required. Meas unavailable.

A demod measurement was attempted with no Bluetooth FM demod card present (Option 106).

10290 Parameter unavailable in demod measurements.

You have selected (by remote SCPI command) either RF Amplitude sync or Video trigger while running one of the demod measurements.

10291 Opt B7E RF hardware required. RF Burst unavailable.

You have selected (by remote SCPI command) RF Burst Trigger with no digital demodulation RF card present (RF Communications Hardware (Option B7E)).

10320 Opt 106 hardware required. Preamble sync unavailable.

You have selected (by remote SCPI command) preamble sync with no Bluetooth FM demodulation card present (Option 106).

10321 Start Marker must be at least 1% < Stop Marker.

You have attempted to input a start marker value that will result in the difference between the start and stop markers being less than 1%.

10322 Stop Marker must be at least 1% > Start Marker.

You have attempted to input a stop marker value that will result in the difference between the start and stop markers being less than 1%.

Instrument Messages

10323 Unable to Calculate Result using Current Setup.

You have changed the setup parameters such that the marker lines used to measure the power cannot be displayed therefore accurate measurements cannot be made.

Chapter 1 71

Page 72

Instrument Messages

10340 ’10101010’ pattern not detected - results may be inaccurate.

This message is displayed if the measurement cannot detect the ‘10101010’ pattern in the payload. The measurement will continue and carry out the calculations on the payload data supplied, but may not be correct.

10350 Payload data pattern ‘10101010’ not present.

This message is displayed when the “Payload Data” parameter is set to Auto and the measurement has not detected either of the required patterns in the payload.

10351 Required payload data pattern ‘10101010’ not present.

This message is displayed after successfully measuring and holding the ‘11110000’ pattern if the measurement is restarted and the ‘10101010’ data pattern is not detected.

10352 Required payload data pattern ‘11110000’ not present.

This message is displayed after successfully measuring and holding the ‘10101010’ pattern if the measurement is restarted and the ‘11110000’ data pattern is not detected.

10353 There is no valid result to hold.

You have attempted to hold either ∆ f1 or ∆f2 before it has been measured.

10360 Can’t compute result - not enough transitions.

This message is displayed when the measurement cannot find either a 111, 000, 101 or 010 pattern and is therefore unable to calculate the low or high frequency deviations.

10389 Valid EDGE burst not found in frame (Burst Type)

No active EDGE bursts that match the selected burst type have been detected in the RF input signal. Search was performed over the complete

Instrument Messages

EDGE frame.

10390 Valid EDGE burst not found in specified timeslot (Burst Type)

No active EDGE bursts that match the selected burst type have been detected in the RF input signal. Search was performed over the specified timeslot.

10391 Valid EDGE burst not found in frame (Ref Burst)

No active EDGE bursts that match the selected burst type have been detected in the RF input signal. Search was performed over the specified complete EDGE frame using the Ref Burst setting.

72 Chapter 1

Page 73

Instrument Messages

10392 B7D DSP Code Fail. Reload Opt. 202. Contact your Service

Center

The DSP algorithm files required to perform the demodulation are not present in the instrument ISDP: drive.

10393 Opt 252 DSP algorithm code file requires upgrade.

10394 Opt 252 DSP algorithm coef. file requires upgrade.

10395 B7D DSP Code Fail. Reload Opt. 202. Contact your Service

Center.

The DSP algorithm files required to perform the demodulation are present in the instrument ISDP: drive, but cannot be loaded properly into DSP RAM.

10396 EDGE Upgrade (252) unlicensed. Please contact your Agilent

Sales Rep.

10400 Valid signal not found.

This error is normally generated because of one of the following reasons:

1. There is no carrier signal.

2. The carrier signal power has changed during the measurement, causing

ADC to over/under range.

3. There is some other modulation problem that will prevent the

measurement from being made. This problem must be corrected before the measurement can continue.

10401 Valid burst not found in frame (Burst Type).

No active bursts that match the Burst Type have been detected in the RF input signal. The search was performed over the complete frame.

10402 Valid burst not found in specified timeslot (Burst Type).

No active bursts that match the Burst Type have been detected in the RF input signal. The search was only performed over the specified timeslot setting.

10403 Sync word not found in frame (TSC).

One or more active EDGE bursts that match the Normal Burst Type have been detected in the RF Input signal, but none contain the selected Training Sequence Code (TSC). The search was performed over the complete EDGE frame.

10404 Sync word not found in specified timeslot (TSC).

Instrument Messages

Chapter 1 73

Page 74

Instrument Messages

10409 Wideband calibration not valid until Align Now, All performed.

Wideband calibration corrections cannot be applied to current demodulation results. Results will not meet specified demodulation performance levels until an Align Now, All has been performed.

10410 Measurement uncalibrated, wideband calibration required.

Wideband calibration corrections cannot be applied to the current demodulation results. Results will not meet specified demodulation performance levels until

Wideband Cal has been selected and successfully

performed.

10411 Measurement uncalibrated, symbol rate exceeds +/-10% nominal.

Wideband calibration corrections cannot be applied to current demodulation results, due to the

Symbol Rate setting exceeding +/-10% of

the nominal value. Results may not meet specified demodulation performance levels.

10412 Cal Data corrupt. Wideband cal failed. Using previous data.

Wideband calibration procedure failed for an unknown reason. New calibration data was not saved. Previous wideband calibration data is being used, if available. However, it is not acceptable. Before re-attempting Wideband Cal, ensure connection between the

INPUT 50 Ω is in place. If the error persists, get in touch with your service

AMPTD REF OUT and the

center.

10413 B7D DSP Code Install Fail Opt.229. Contact your Service

Center.

The Digital Signal Processor algorithm files required to perform the demodulation are not present in the analyzer. Reinstall the measurement personality and contact your service center.

10414 Opt 229 DSP algorithm code file requires upgrade.

Instrument Messages

10415 Opt 229 DSP algorithm coef. file requires upgrade.

The Digital Signal Processor algorithm coefficient file revision is not supported by the currently loaded personality version. Refer to the user guide for the personality in use for more information on installation/upgrade.

10416 B7D DSP Code Reload Fail Opt.229. Contact your Service Center.

The Digital Signal Processor algorithm files required to perform the demodulation are corrupt and cannot be loaded properly. Reinstall the measurement personality and contact your service center.

74 Chapter 1

Page 75

Instrument Messages

10417 This operation requires a measurement to be active.

The analyzer cannot perform this operation, because it requires a measurement to be running and no measurement is running.

10418 Demod Format setting does not allow this value for

Points/Symbol.

Invalid Points/Symbol selection attempted for the given Demod Format setting.

10419 Carrier Not Present.

A carrier signal/burst is expected at the analyzer input. This signal cannot be found; however, the measurement will still run. Check input signal connection.

10420 Valid burst not found.

This error only occurs when

RF Amptd is selected for Burst Sync. It

indicates that a valid burst envelope which meets the specified Burst Search Threshold was not found within the specified Burst Search Length. Note that the demodulation measurement will proceed by attempting to demodulate the signal without Burst Sync alignment. Possible causes may be:

1. Carrier signal is not actually bursted.

2. Burst Search Threshold and/or Burst Search Length may need to be adjusted.

10421 Cannot lock to carrier.

This error only occurs when attempting to demodulate OFFSET QPSK signals. It indicates that the demodulation algorithm is unable to lock to your signal. Possible causes may be:

1. There is no carrier signal.

2. Carrier signal is present, but Demod settings do not match the modulation format of the OFFSET QPSK signal being measured.

3. OFFSET QPSK signal is too noisy to achieve carrier lock.

10425 B7D DSP Code Install Fail Opt.231. Contact your Service

Center.

Instrument Messages

The Digital Signal Processor algorithm files required to for the 89600 VSA SW are not present in the analyzer. Reinstall the measurement personality and contact your service center.

10426 Opt 231 DSP algorithm code file requires upgrade.

Chapter 1 75

Page 76

Instrument Messages

10427 Opt 231 DSP algorithm coef. file requires upgrade.

installation/upgrade.

10428 B7D DSP Code Reload Fail. Opt.231. Contact your Service

Center.

The Digital Signal Processor algorithm files required for the 89600 VSA SW are corrupt and cannot be loaded properly. Reinstall the measurement personality and contact your service center.

10450 Avg Mode changed to Repeat for Full Meas Type.

Meas Type has been changed to Full. Exponential Average Mode is not available for Full Meas Type therefore Average Mode has been changed to Repeat.

10451 Avg Mode changed to Exp for Examine Meas Type.

Meas Type has been changed to Examine. Repeat Average Mode is not available for Examine Meas Type therefore Average Mode has been changed to Exponential.

10452 Meas Type changed to Examine for Exp Avg Mode.

Average Mode has been changed to Exponential. Full Meas Type is not available for Exponential Average Mode therefore Meas Type has been changed to Examine.

10453 Meas Type changed to Full for Repeat Avg Mode.

Average Mode has been changed to Repeat. Examine Meas Type is not available for Repeat Average Mode therefore Meas Type has been changed to Full.

Instrument Messages

10454 Valid burst not found.

Cannot find a valid burst, either because it is not fully on the display, or the level is too low to be detected properly.

10509 Did not find 4 signals > Peak Excursion.

Require 4 Signals > PEAK EXCURSION above Threshold.

Using the current instrument settings, the measurement cannot locate four signals with enough energy or resolution to perform an accurate measurement.

76 Chapter 1

Page 77

Instrument Messages

10510 Signals do not fit expected Intermod (TOI) pattern.

Based on the current analyzer settings, the measurement cannot find two signals of high enough amplitude that can be resolved in such a manner that the third order products would lie within the measured span. You need to widen the span to include TOI products.

10511 100 spurs found. Additional spurs ignored.

There are too many spurs for the table (the limit is 100), and any additional spurs that are found will be ignored

10512 No spurs have been found.

You have started a measurement in examine meas type, in single or continual sweep mode, or full meas type in single sweep mode, but no spurs were found.

10513 No ranges are defined.

There are no active ranges in the range table. You will need to activate at least one range.

10514 Avg Mode changed to Repeat for Full Meas Type

Meas Type has been changed to Full. Exponential Average Mode is not available for Full Meas Type therefore Average Mode has been changed to Repeat.

10515 Avg Mode changed to Exp for Examine Meas Type

Meas Type has been changed to Examine. Repeat Average Mode is not available for Examine Meas Type therefore Average Mode has been changed to Exponential.

10516 Meas Type changed to Examine for Exp Avg Mode

Average Mode has been changed to Exponential. Full Meas Type is not available for Exponential Average Mode therefore Meas Type has been changed to Examine.

10517 Meas Type changed to Full for Repeat Avg Mode

Average Mode has been changed to Repeat. Examine Meas Type is not available for Repeat Average Mode therefore Meas Type has been changed to Full.

10518 Invalid State Register

There are only a limited number of instrument state registers/locations available.

Instrument Messages

10520 Command not supported

Command my not be supported configuration or with the current settings of other related functions.

Chapter 1 77

Page 78

Instrument Messages

10524 to 10561: Phase Noise Error Messages (Option 226) An error number in this range indicates the instrument has detected an error relating to the Phase Noise personality.

10524 This measurement does not support the *.CSV file format.

You cannot load or save base instrument traces, as this is not supported by the Log Plot measurement.

10525 Invalid format: CSV files are not supported by this

measurement.

You cannot load or save base instrument traces, as this is not supported by the Log Plot measurement.

10525 Use View/Trace menu when loading or saving logarithmic traces.

You cannot load CSV format trace files or save traces in the CSV format in the Log Plot measurement of the Phase Noise Measurement Personality.

10526 Cannot display Ref Trace because it has no data.

Reference trace cannot be displayed, as there is currently no data assigned to it - use the functions under the Store Ref Trace menu, or load a trace to assign some data.

10527 Invalid Marker Trace. Marker moved to Raw Trace.

Cannot place markers on the reference trace, because the reference trace is currently turned off or has no data.

10529 Failed to Load trace. Bad file format.

The load trace operation could not be completed, as the input file was not in the expected format. You can only load traces that were previously saved using the 'Save Trace' feature.

10530 Trace file contains no compatible traces.

The trace file may have been created by another version of the Phase Noise

Instrument Messages

personality, which uses a different trace format that is incompatible with the version you are running. Please check you are running the most up to date version of the personality.

10531 Trace file was created by incompatible version of Opt. 226

The trace file may have been created by another version of the Phase Noise personality, which uses a different trace format that is incompatible with the version you are running. Please check you are running the most up to date version of the personality.

10532 Cannot open trace file for writing. Save Failed.

Cannot write the trace file to the destination filename. This could be because the disk is full, or possibly due to a filename error. If using a floppy disk, check there is a formatted disk in the drive.

78 Chapter 1

Page 79

Instrument Messages

10533 Cannot save Trace because it contains no data.

Cannot save Ref Trace because it contains no data.

Check the Ref Trace is turned on, and contains some valid trace data.

10534 Trace file saved successfully.

The trace saving operation was successful.

10535 Carrier Not Present

No Carrier > -50 dBm found at the analyzer input within the search span. Solution: Modify center frequency to be closer to actual carrier, or alternatively apply carrier of sufficient amplitude at the current center frequency.

10535 Cancellation trace is not set to Reference or has no data.

When performing phase noise cancellation, you need to supply a reference trace that will be used to cancel out the background noise of the analyzer. The reference trace must be in Reference (View) mode, and selected by the Ref Trace parameter under the Cancellation menu.

10536 Cancellation disabled while measuring DANL Floor.

Phase Noise cancellation does not make sense when measuring the DANL Floor, so for this reason it has been disabled.

10537 10537 Cancellation trace has different X-Scale to Smoothed

trace.

When performing phase noise cancellation, you need to supply a reference trace that will be used to cancel out the background noise of the analyzer. The reference trace must have been measured over the same range of offsets, and on the same instrument as the current measurement being performed.

10560 Carrier Not Present. Verify frequency and amplitude settings.

No Carrier > –50 dBm found at the analyzer input within the search span. Solution: Modify center frequency to be closer to actual carrier, or alternatively apply carrier of sufficient amplitude at the current center frequency.

10561 Signal Tracking disabled when measuring DANL Floor (Removal).

Measuring the DANL Floor with DANL Method set to Removal requires that you remove the signal and attach a load to the analyzer RF Input. Signal Tracking requires that the carrier be measured many times per measurement, so the two are inherently incompatible.

Instrument Messages

Chapter 1 79

Page 80

Instrument Messages

10601 to 10700: GSM and EDGE Error Messages (Options BAH and 202) An error number in this range indicates the instrument has detected an error relating to the GSM or EDGE personality.

10602 Sync word not found

An attempt to position a GSM trace into the mask, when not enough data was present. Try using the

Restart key to clear the problem. This can be

caused by a bad GSM burst, or the RF Sync Delay set too far.

10604 GSM burst out of limits

The GSM signal did not fit into the mask in the Power vs. Time measurement.

10606 Insufficient pre-Trig for demod - decrease Trig Delay

10608 Incorrect RBW for demod - change RBW

10610 GSM Hopping enabled, waiting for valid burst

10612 Invalid GSM burst timing

A GSM-like burst was acquired, but its timing is not valid. Ensure the correct

Burst Type has been selected.

10614 Valid GSM burst not found

In a GSM measurement, data was acquired but a GSM burst was not found, with the timeslot mode disabled.

10138 Valid GSM burst not found in frame (Burst Type).

No active GSM bursts that match the selected Burst Type have been detected in the RF input signal. The search was performed over the complete GSM frame.

10139 Valid GSM burst not found in specified timeslot (Burst Type).

No active GSM bursts that match the selected Burst Type have been

Instrument Messages

detected in the RF input signal. The search was only performed over the specified timeslot setting.

10140 Valid GSM burst not found in frame (Ref Burst).

No active GSM bursts that match the selected Burst Type have been detected in the RF input signal. The search was performed using the Ref Burst type setting over the complete GSM frame.

10616 Cannot synchronize frame trigger

Cannot synchronize the frame trigger to the even second clock.

10618 Dynamic range not optimum

10620 Cannot synchronize to RF amplitude (burst error)

80 Chapter 1

Page 81

Instrument Messages

10622 GSM RF sync delay is out of range

Change RF Sync Delay.

10624 Sync word not found

In a GSM measurement using demodulation, the training sequence code (sync word) could not be found.

10141 Sync word not found in frame (Burst Type)

One or more active GSM bursts that match the selected Burst Type have been detected in the RF Input signal, but none contain the selected Training Sequence Code (TSC). The search was performed over the complete GSM frame.

10142 Sync word not found in specified timeslot (Burst Type)

10143 Sync word not found in frame (Ref Burst)

10626 Signal too noisy

In a GSM measurement, indicates that a burst could not be found in a signal that appears noisy.

10628 Sync is RF Ampl (not Training Seq). Bits not accurate

10630 Marker X value not adjusted when right of Rise&Fall mark

10632 Incorrect trigger holdoff

10634 Break freq > FFT filter edge

10636 SCPI marker query not available in GSM Rise&Fall

10638 GSM Pwr Meas requires trig delay < −50 µs. Delay set to −50 µs

10640 Carrier frequency outside device’s transmit band

The entered channel/carrier frequency is not within the range of your current mode setup selection of standard and device.

Instrument Messages

10642 ADC overload -- Carrier not at expected frequency

The carrier frequency of the signal may not match the instruments channel frequency setting.

Chapter 1 81

Page 82

Instrument Messages

10644 Requested timeslot number not present

The selected timeslot is not on. (Timeslot is referenced to the trigger point.)

10646 Tx Band Spur measurement not defined for mobiles

Only base station testing is available.

10648 Carrier power too low for optimum dynamic range

For better dynamic range, transmit band spur measurements require >10 dBm signal power at the RF input port.

10650 Unexpected carrier frequency (BMT only)

The transmit band spur measurement only allows bottom (B), middle (M), and top (T) channel frequencies for each supported frequency band. The carrier frequency must be set to the bottom, middle or top frequency of the current frequency band.

10652 EVM Measurement only supports EDGE TCH burst type

10654 Unable to demodulate signal

10655 Input overload

Excessive input power has been detected which will cause the ADC to clip the signal. Reduce the signal level, change the attenuator setting (under

Input menu), or press Restart if the RF Input Range is Auto.

10656 Tx Band Spur measurement does not support this frequency band

The transmit band spur measurement does not support all of the commercially available frequency bands. You need to change your selection under

Mode Setup, Radio, Band to one of the supported bands.

10657 Pretrigger too long

10658 Valid GSM burst not found for selected timeslot

Instrument Messages

In a GSM measurement, data was acquired but a GSM burst was not found, with the timeslot mode enabled.

10659 Sync not found on AM path

The instrument failed to find the training sequence on the AM path.

10660 Sync not found on PM path

The instrument failed to find the training sequence on the PM path.

10661 Sync not found on AM and PM path

The instrument failed to find the training sequence on both the AM and the PM paths.

82 Chapter 1

Page 83

Instrument Messages

10662 Inconsistent sync word

The instrument detected the training sequence, but the training sequence number is inconsistent between the AM path and the PM path.

10701 to 10800: W-CDMA Error Messages (Option BAF) An error number in this range indicates the instrument has detected an error relating to the W-CDMA personality.

10702 Signal too noisy

10704 Input power too low

The instrument only identifies a channel as active if it meets the default threshold criteria that it is within 20 dB of the highest power code channel. The threshold can be changed using the Active Set Threshold function in the Meas Setup menu.

10768 Cannot correlate to input signal

Cannot correlate to the input signal and no active channel is found. (from the composite EVM measurement) An active channel must meet the default threshold criteria that it is within 20 dB of the highest power code channel. The threshold can be changed using the active set threshold function in the Meas Setup menu.

10772 Burst not found.

Either the signal being analyzed has insufficient power, the rising or falling edges cannot be detected, or the burst is less than 126 microseconds.

10776 PSA Cannot sync DPCCH pilot.

Cannot synchronize measurement with DPCCH pilot for Power Control measurement, because the pilot signal cannot be found. Make sure DPCCH is present in the W-CDMA uplink signal, and that the slot format and scramble code are set correctly.

10778 PSA Valid PRACH burst not found.

Cannot synchronize measurement with PRACH channel for Power Control measurement, because the signal cannot be found. Make sure PRACH is present in the W-CDMA uplink signal, and that the preamble signature and scramble code are set correctly.

10780 Critical memory shortage occurred.

This error message appears when a critical memory shortage occurs, and the current measurement is aborted. To continue, restart the measurement by pressing the

Preset key, or by exiting and then

re-entering the current mode or the current measurement, or cycle the power.

Instrument Messages

Chapter 1 83

Page 84

Instrument Messages

10788 Stored data length too short

Stored acquisition data length is too short. You need to perform one or more of the following actions:

• Use the same

Sync Type setting that was used when the data was

acquired.

• Use the same

Start Sync Slot setting that was used when the data was

acquired.

• Reduce the

Capture Interval setting.

10790 Slot format auto-detection not supported by slot power meas

The slot format auto-detection (AUTO selected) is not supported by

Power

measurement type. It is supported only by Slot Phase measurement

Slot

type.

10792 Not enough memory. Decrease Capture Interval.

Not enough memory left and the measurement cannot continue. You need to reduce the

Capture Interval setting and then restart the measurement to

recover from this situation.

10801 to 10900: cdma2000 Error Messages (Option B78) An error number in this range indicates the instrument has detected an error relating to the cdma2000 personality.

10824 Signal too noisy

10826 Input power too low

10868 Can not get long code phase (RS-232)

Instrument Messages

For MS (mobile station) measurements, the long code phase information could not be obtained from the signal at the RS-232 port (from code domain power measurement or composite EVM measurement).

10872 Cannot correlate to input signal

Cannot correlate to the input signal and no active channel is found. (from composite EVM measurement) An active channel must meet the default threshold criteria that it is within 20 dB of the highest power code channel. The threshold can be changed using the active set threshold function in the Meas Setup menu.

84 Chapter 1

Page 85

Instrument Messages

10901 to 10925: NADC Error Messages (Option BAE) An error number in this range indicates the instrument has detected an error relating to the NADC personality.

10902 Sync word not found

In an EVM measurement, the sync word is not found and the synchronization cannot be established when

Burst Sync menu.

Sync Word is selected in the

10904 Valid NADC burst not found

A valid NADC burst is not found when the

Device is MS.

10906 Signal too noisy

The valid EVM measurement cannot be performed, because the input signal is too noisy.

10908 Burst Delay out of limit for EVM (2 ms)

In an EVM measurement, the

Burst Delay value must be less than 2 ms.

10926 to 10950: PDC Error Messages (Option BAE) An error number in this range indicates the instrument has detected an error relating to the PDC personality.

10926 Sync word not found

In an EVM measurement, the sync word is not found and the synchronization cannot be established when

Burst Sync menu.

Sync Word is selected in the

10928 Valid PDC burst not found

A valid PDC burst is not found when the

Device is MS.

10930 Signal too noisy

Instrument Messages

The valid EVM measurement cannot be performed, because the input signal is too noisy.

10932 Burst Delay out of limit for EVM (2 ms)

In an EVM measurement, the

Burst Delay value must be less than 2 ms.

10951 to 10975: cdmaOne Error Messages (Option BAC) An error number in this range indicates the instrument has detected an error relating to the cdmaOne personality.

10952 Signal exceeds maximum allowable power

10954 Input overload

Excessive input power has been detected which will cause the ADC to clip the signal. Reduce the signal level, change the attenuator/max total power setting (under

Chapter 1 85

Input menu), or press Restart if the RF Input Range is Auto.

Page 86

Instrument Messages

10956 Channel center frequency outside device’s transmit band.

10960 No power at carrier frequency

No power was detected as a CW or a modulated signal.

10962 Cannot correlate to input signal

A correlation failure with the pilot CDMA channel occurred during synchronous demodulation.

10976 to 11000: Programming Code Compatibility Messages (Option 266) An error number in this range indicates the instrument has detected an error relating to the Programming Code Compatibility Suite.

10976 CMD ERR, <name of offending command>

When a command or command argument is not recognized by the parser a command error is generated.

10977 PARAMETER ERROR, <name of offending parameter>

When an illegal parameter is sent following a command. For example, when the “GRAT” or “ANNOT” 8566 series commands are used with arguments other than ON, OFF, 1 or 0.

10978 INVALID ITEM, <offending item>

The invalid item message appears when a value that is not part of the commands list of enumerated arguments is entered.

10979 INVALID SAVE REG, <invalid register>

When the RCLS or RC commands are used to recall a state register that wasn’t previously saved with the SAVES or SV commands.

10980 INVALID TRACE, <trace>

Instrument Messages

When the argument to a trace command is not part of the predefined trace enumeration (TRA, TRB or TRC).

10981 CMD NOT SUPPORTED, <command>

Command not supported errors are generated when a valid 8566 command that is not supported by Chameleon is executed.

10982 LOG FILE FULL, CLEAR FOR FURTHER ERROR LOGGING

10983 LOG FILE CLEARED

86 Chapter 1

Page 87

Instrument Messages

12000 to 12999: Noise Figure Error Messages (Option 219) An error number in this range indicates the instrument has detected an error relating to the Noise Figure personality.

12116 Two entries already exist at frequency.

When specifying limit line point, if there are more than two points at the same frequency, the new limit point is discarded and the existing limit is used.

12219 Command not valid in this mode.

Indicates that the command sent from the Remote interface does not apply for this DLP.

12303 User cal invalidated

The existing user cal has been invalidated because of one of the following reasons:

•Meas mode changed

• Freq outside cal range

•Fixed LO changed

• Sideband changed

12304 Alignment Failed

Calibration failed because an error was encountered at some point during the calibration (for example gain < 0)

12305 Mode Setup Error

A mode setup error occurred because of one of the following:

• System input frequency out of range

• External LO frequency out of range

• Stop freq must be less than fixed LO freq

• Start freq must be greater than start IF freq

• LO – Stop freq must be >= min system input freq

• Start freq must be greater than fixed LO freq

• Stop IF freq must be less than fixed LO freq

• Start – LO freq must be >= min system input freq

• Stop freq must be less than stop RF freq

• Start freq must be greater than start RF freq

12307 Required Input attenuation not calibrated

Corrected measurements have been requested and the required RF front-end setting of x dB has not been calibrated.

12308 Invalid frequency list for measurement mode

Instrument Messages

A frequency within the frequency list cannot be used to make a measurement in the current mode.

Chapter 1 87

Page 88

Instrument Messages

12309 No entries in frequency list

A measurement was attempted with List frequency mode or a SCPI query of the frequency list table was made and the frequency list table is empty.

12310 No entries in ENR table

A measurement was attempted or a SCPI query of an ENR table was made and there were no entries in the relevant ENR table (Common, Meas or Cal).

12311 No entries in Limit Line table

An attempt is made to either display or test against a limit line table which has no entries.

12312 RF re-range required: Meas Restarted.

During a continuous measurement, a change of RF front-end attenuation was required. To do this the measurement needs to be restarted.

12313 IF over range req. RF re-range: Meas Restarted.

During a continuous measurement, an IF section over range condition occurred, requiring a change of RF front-end attenuation. To do this, the measurement needs to be restarted.

12314 No entries in loss table

A measurement is attempted or a SCPI query of a before or after loss table is made and there are no entries in the relevant loss table

12316 T hot must be greater than T cold

A spot T hot has been specified which is not greater than T cold.

12603 Illegal MSDOS name given

An invalid filename has been specified. Use filenames with a maximum of 8 characters (letters and digits only) and use a 3 character extension. Note

Instrument Messages

that lowercase and uppercase are perceived as the same.

12604 File already exists

Attempt to store a file that already exists. Delete or rename the old file and try again

12605 Media is protected

A store was attempted to a write-protected device.

12606 Media is not writable

A store was attempted to a read-only device.

12612 File does not exist

The file you were trying to recall could not be found.

88 Chapter 1

Page 89

12762 Incorrect filename, allowable extension CSV

Attempt to load/store table data with an incorrect extension.

12768 Failed to load ENR data

A problem occurred when trying to load or store table data.

12769 Failed to store ENR data

A problem occurred when trying to load or store table data.

12770 Incorrect filename, allowable extension ENR

Attempted to load/store table data with an incorrect extension.

12771 Failed to load Frequency List

A problem occurred when trying to load or store table data.

12772 Failed to store Frequency List

Attempt to load/store table data with an incorrect extension.

12773 Incorrect filename, allowable extension LST

Instrument Messages

Attempt to load/store table data with an incorrect extension.

12774 Failed to load Limit line

Attempt to load/store table data with an incorrect extension.

12775 Failed to store Limit line

Attempt to load/store table data with an incorrect extension.

12776 Incorrect filename, allowable extensions LIM

Attempt to load/store table data with an incorrect extension.

12778 Failed to store Trace

A problem occurred when trying to load or store table data.

12779 Failed to load Loss data

A problem occurred when trying to load or store table data.

12780 Failed to store Loss data

A problem occurred when trying to load or store table data.

12781 Incorrect filename, allowable extension LOS

Attempt to load/store table data with an incorrect extension.

Instrument Messages

12995 Noise Figure DLP requires Noise Source Control Hardware

You have attempted to initiate the Noise Figure mode with the Noise Source Control hardware installed in your instrument. You must install the Noise Source Control hardware before running the Noise Figure mode.

Chapter 1 89

Page 90

Instrument Messages

13214 Frequency Hopping enabled, waiting for valid burst

The demodulated burst type has not been found in the originally demodulated slot location within the frame.

13001 to 13100: 1xEV-DO Error Messages (Option 204) An error number in this range indicates the instrument has detected an error relating to the 1xEV personality.

13024 Signal too noisy

13026 Input power too low

Meas Setup menu.

13070 Cannot correlate to input signal

Meas Setup menu.

13074 Valid 1xEV burst not found

In a 1xEV measurement, data was acquired but a 1xEV burst was not found, with the timeslot mode disabled.

13076 Critical memory shortage occurred

This error message appears when a critical memory shortage occurs, and the current measurement is aborted. To continue, restart the measurement by pressing the

Preset key, or by exiting and then

re-entering the current mode or current measurement, or cycle the power.

Instrument Messages

13080 PSA No Active slot is found

Occurs when

Meas Slot Type is Active and the Active slot is not found

during the capture interval. Synchronization occurs and the pilot is found but no results are included in peak/average calculation.

13082 PSA No Idle slot is found

Occurs when

Meas Slot Type is Idle and the Idle slot is not found during the

capture interval. Synchronization occurs and the pilot is found but no results are included in peak/average calculation.

90 Chapter 1

Page 91

Instrument Messages

13086 PSA Memory shortage occurred; consider decreasing Capture Intvl

This error message appears when memory shortage, related to long capture interval, occurs. The current measurement is aborted and all the results returned are invalid values. Decrease

Capture Intvl and restart the

measurement.

13101 to 13200: Flexible Digital Modulation Analysis Error Messages (Option

241) An error number in this range indicates the instrument has detected an error

relating to the Flexible Digital Modulation Analysis personality.

13102 Valid signal not found

The input signal cannot be demodulated because of inappropriate parameter settings or incorrect signal

13104 Valid burst not found

The burst signal cannot be detected because of inappropriate parameter settings or incorrect signal.

13106 Sync word not found

The sync word cannot be detected because of inappropriate parameter settings or incorrect signal.

13108 Points/Symbol changed to an even number because of demod

format

Offset QPSK allows only even values for points/symbol. The demod format was changed to OQPSK while the points/symbol was set to an odd value. Therefore, the points/symbol was re-set to an even number.

13110 Sync Pattern includes non-hex characters

The sync pattern should only consist of hex characters. Invalid characters are converted to 0.

13112 Sync Word Length changed to new upper limit

The upper limit of Sync word bits is 128. If the code word length (sync word length) exceeds this value, then the sync word length is cut off. This warning may happen only when the demod format is changed.

13114 Sync offset value not valid

The sync offset value is too far off from a value that would be reasonable to measure valid portion of data. So the measurement gives up trying to apply the offset value.

Instrument Messages

Chapter 1 91

Page 92

Instrument Messages

13116 Search Length is clipped to the upper value according to the

dependency of IF Band Width

Search length upper limits: IF Band Width <= 1 MHz, Limit = 0.1 sec 1MHz < IF Band Width <= 10MHz, Limit = 0.05 sec 10MHz < IF Band Width <= 20MHz, Limit = 0.025 sec 20MHz < IF Band Width <= 40MHz, Limit = 0.013 sec 40MHz < IF Band Width, Limit = 0.007sec

13118 Search Length is clipped to the lower value as allowed by

current IF Band Width.

Search length lower limits: IF Band Width <= 10MHz, Limit = 0.001 sec; 10MHz < IF Band Width Limit = 0.1 µsec

13120 Symbol Rate is clipped to its limit because of IF Path change.

Upper limit of Symbol Rate is 10 MHz when IF Path is Narrow.

13122 IF BW is clipped to its limit because of IF Path change.

Limit of IF BW depends on IF Path selection. If the value exceeds the limit, it is clipped to the limit. This message will not appear when IF BW is set to AUTO.

13124 Meas Interval is clipped to its upper limit because of

points/symbol change.

Upper limit of Meas Interval depends on points/symbol setting.

13126 Only one marker is available on Demod Bits trace.

Only one marker is available on Demod Bits trace.

13201 to 13300: Stimulus-Response Measurements Error Messages (Option 215)

Instrument Messages

An error number in this range indicates the instrument has detected an error relating to the Stimulus Response measurement personality.

13226 Connection could not be established with specified IP Address.

A communication connection could not be established at the specified IP Address. Check that the IP address entered is correct and that the signal generator and PSA are both connected to the LAN or are connected to one another using a LAN cross-over cable. If you are using a LAN cross-over cable the IP address of both instruments must start with the same first two integers. For example, if the analyzer IP address is 156.121.102.33 then the source IP address must be 156.121.xxx.xxx.

92 Chapter 1

Page 93

Instrument Messages

13227 Freq range of ext src exceeded, PSA setting adjustments

required.

The calculated external source start or stop frequency exceeds the frequency range of the external source. You need to adjust the PSA settings so that the required source frequency is within it’s available range. You may need to adjust the PSA start frequency, the PSA stop frequency, the harmonic number (if on) and/or the frequency offset (if on). The sweep will start again once the required frequency range is in the range available to the source. See the Option 215 documentation for more information about making these settings adjustments.

13228 Unable to store reference trace.

Unable to copy the data from trace 1 to trace 3. There is no data in trace 1.

13230 Hardware upgrade required. Option 215 disabled.

Option 215 requires the gated sweep hardware. It has not been detected, so an update is required. You should contact the local sales engineer and order E444xAU Option 426.

13231 Freq band crossing not supported by Option 215

Option 215 does not support sweeping across a spectrum analyzer hardware frequency band edge. For detailed frequency band information, refer to the “Getting Started” information in the Option 215 guide.

13232 Video bandwidth fixed at 50MHz by Option 215

Option 215 forces the video bandwidth to be set to 50MHz when the external source control state is set to ON

13233 Agilent PSG-A Series Signal Generators not supported.

Option 215 does not support the PSG-A signal generators. This includes model number E8241A, E8242A, E8251A and E8254A.

13234 Open/Short CAL not possible, freq band crossing detected

You cannot perform a calibration if your PSA span includes frequencies in more then one frequency band. Please adjust either the PSA start frequency or its stop frequency to stay within a single frequency band. The frequency band ranges are listed in the external source control guide “Getting Started” chapter.

Instrument Messages

Chapter 1 93

Page 94

Instrument Messages

13301 to 13400: WLAN Error Messages (Option 217) An error number in this range indicates the instrument has detected an error relating to the WLAN measurement personality.

13338 Valid burst not found, extend search length

The instrument cannot find a valid WLAN burst. You may need to extend the search length.

13340 Synchronization failed, check signal format

The instrument cannot synchronize the signal. Make sure the signal format is correct

13342 Data is too short to measure

There is not enough data for proper analysis.

13382 Measurement Input Overload

The analyzer’s ADC input is overdriven. You need to reduce the signal power at the input by using an external attenuator, or by increasing the internal input attenuation of the analyzer.

13384 Point Quantities Limited

The capture point size exceeds the limit.

13386 Span Limited

The span exceeds the limit.

13388 Meas Offset exceeds valid burst length

The measurement offset exceeds the burst length detected. Default values are returned.

13401 to 13500: Measuring Receiver Error Messages (Option 233) An error number

Instrument Messages

in this range indicates the instrument has detected an error relating to the Measuring Receiver measurement personality.

13436 PSA Power meter connection failure

Attempt to connect to the power meter has failed. Please make sure that the power meter is connected to the PSA and the connection settings are correct.

13438 PSA Power meter connection time-out

A time-out occurred while the instrument was attempting to establish a connection with the power meter.

13440 PSA No cal factor for power sensor

This message occurs when the power sensor model name is “NONE” or the calibration factor table is empty.

94 Chapter 1

Page 95

Instrument Messages

13442 PSA Power meter zero and calibration required

The power meter requires zeroing and calibration.

13444 PSA Power meter zero required

The power meter requires zeroing.

13446 PSA Power meter calibration required

The power meter requires calibration.

13448 PSA Power meter zero failure

The power meter zero function has failed.

13450 PSA Power meter calibration failure

The power meter calibration has failed.

13456 PSA Power meter reading not available. Retrying to connect.

The Tuned RF Level measurement cannot read the power meter. The instrument is attempting to establish a connection.

13458 PSA Power meter model is not supported

The power meter model used is not supported by this version of the firmware.

13460 PSA Power sensor hardware is missing

There is no power sensor connected to the input of the power meter.

13462 PSA RF frequency is beyond frequency range of cal factor table

The frequency of the input signal is either higher than the highest, or lower than the lowest frequency in the cal factor table of the power sensor.

13464 PSA Audio level is out of range

Audio Range is not properly set. The input level is beyond the range.

The

13466 PSA Audio data acquisition failure

Audio measurement failed to acquire data due to I/O error. Data was lost or DMA (direct memory access) aborted.

13727 to 13753: EMC Analyzer Error Messages (Option 239) An error number in this range indicates the instrument has detected an error relating to the EMC Analyzer personality.

Instrument Messages

13727 PSA EMC Analyzer

This message occurs when the PSA spectrum analyzer is placed in the EMC Analyzer mode.

Chapter 1 95

Page 96

Instrument Messages

13729 PSA Connection with the Presel could not be established at the IP

A communication connection could not be established at the RF preselector IP Address. Check to make sure that the IP Address that was entered is correct. Also make sure that the RF preselector and PSA are both connected to the LAN.

13731 PSA RF Presel model is not supported

The connected RF preselector model is not supported.

13733 PSA Connection with Source could not be established at the IP

A communication connection could not be established at the source IP Address. Check to make sure that the IP Address that was entered is correct. Also make sure that the source and PSA are both connected to the LAN.

13735 PSA Connection with Source could not be established at the IP/GPIB

13737 PSA Source model is not supported

The connected source model is not supported.

13739 PSA RF Presel conducted and radiated paths need to be aligned

The RF preselector conducted and radiated paths need to be aligned.

13741 PSA RF Presel conducted paths needs to be aligned

The RF preselector conducted paths need to be aligned.

13743 PSA RF Presel radiated paths need to be aligned

The RF preselector radiated paths need to be aligned.

Instrument Messages

13745 PSA RF Presel input is overloaded

The RF preselector input is overloaded.

13747 PSA RF Preselector alignment terminated by user

You have terminated the RF preselector alignment

13749 PSA RF Preselector conducted band alignment fails

The RF preselector conducted band is failing.

13751 PSA RF Preselector radiated band alignment fails

The RF preselector radiated band is failing.

96 Chapter 1

Page 97

Instrument Messages

13753 PSA Frequency crossing Conducted and Radiated Band is not

supported

Option 239 does not support sweeping across Conducted and Radiated Bands. Refer to the “EMC Analyzer Guide” for further details.

Instrument Messages Without Numbers

Error Messages Without Numbers

Error Attempt to change signal data failed.

EMC message, NOT USED

Error Awaiting valid signal.

This indicates that software enhanced triggering is ON and 5 successive failures have been detected within a demod measurement

Error Unable to retrieve signal (remote).

EMC message NOT USED

Error Unable to uninstall personality, file not deletable.

This message occurs when you try to delete a personality which has been marked as non-deletable. The personality is marked non-deletable at the factory. Get in touch with your nearest service center for further assistance.

Informational Messages

These messages simply provide information; you are not required to do anything. Information in brackets (such as <directoryname>), is a previously-provided input.

Informational messages appear at the bottom of the screen in the status line.

Informational <directoryname> directory deleted

The directory indicated has been successfully deleted.

Informational <name1> directory renamed to <name2>

<directoryname1> directory renamed to <directoryname2>

Directory name1 has been successfully renamed to directory name2.

Instrument Messages

Informational <filename> file copied

The filename indicated has been successfully copied.

Informational <filename> file deleted

The filename indicated has been successfully deleted.

Chapter 1 97

Page 98

Instrument Messages

Informational <filename> file loaded

The filename indicated has been successfully loaded.

Informational <filename> file saved

The filename indicated has been successfully saved.

Informational <filename> too many data entries

This message may appear when loading data from a limit line or amplitude correction file. The [DATA] section of such a file can contain at most 200 lines of data. This message is displayed if that limit is exceeded.

Informational <filename1> file renamed to <filename2>

<name1> file renamed to <name2>

File name1 has been successfully renamed to file name2.

Informational Atten auto set to 15 dB

Indicates that an input signal has been detected which is of sufficient level to damage the input circuitry and the input attenuator has been automatically set to 15 dB. If the signal level is reduced, the attenuator will stay at 15 dB. This overload protection occurs at an input power level of 13 dBm (68 dBmV for Option 1DP) ± 7 dB when the input attenuation is auto coupled and set to <15 dB. To return to the original measurement setup, reduce the input signal level and press

Attenuation (Auto).

Amplitude. Then press

Overload protection is only available in the Agilent Technologies E4401B and E4411B.

Informational Auto ranging...

Displayed during autoranging.

Informational B7D and/or B7E not found. Code Domain not available.

Instrument Messages

Digital Signal Processing and Fast Analog to Digital Converter (Option B7D) and/or RF Communications Hardware (Option B7E) are not installed options on your analyzer. Code domain is therefore not available.

Informational B7D and/or B7E not found. Mod Acc not available.

Digital Signal Processing and Fast Analog to Digital Converter (B7D) and/or RF Communications Hardware (B7E) are not installed options on your analyzer. Modulation accuracy is therefore not available.

Informational Carrier Not Present.

A carrier signal/burst is expected at the analyzer input. This signal cannot be found; however, the measurement will still run. Check input signal connection.

98 Chapter 1

Page 99

Informational Channel frequency outside device’s transmit band.

Reset channel number or frequency.

Informational Default spur table values loaded.

No spur table has been previously saved when the Out-of-Band Spurious measurement begins. Press ranges of interest and press

Meas Setup, Edit Table to enter the frequency

Save Table to save that information. This

saved table will be loaded the next time the measurement is run.

Informational Device = Mobile. Code Domain not available.

Code Domain measurement is grayed out when the device is set to mobile under the

Mode Setup front-panel key. Code Domain measurement is only

accessible when the device is set to base and RF Communications Hardware (Option B7E) or Enhanced Memory Upgrade (Option B72) are installed.

Informational Directory already exists

Each directory and file must have a unique name. The directory name you have entered is currently being used on the selected drive. You may either enter a new name or rename the directory currently existent.

Instrument Messages

Informational Device = Mobile. Mod Acc not available.

Modulation accuracy measurement is grayed out when the device is set to mobile under

Mode Setup, front-panel key. Modulation accuracy is only

accessible when the device is set to base and RF Communications Hardware (Option B7E) or Enhanced Memory Upgrade (Option B72) are installed.

Informational Directory already exists

Informational ENR table will be extrapolated

One or more calibration or measurement frequency points exceeds the currently loaded Cal or Meas ENR Table frequency ranges. The corresponding ENR tables lowest frequency ENR value will be re-used for frequencies less than the table range, and the highest frequency ENR value will be re-used for frequencies greater than the table range.

Informational HW Average

For Option 122 or 140 only. If frame triggering is on, this message shows if you turn on the hardware time averaging.

Instrument Messages

Chapter 1 99

Page 100

Instrument Messages

Informational Entire trace is below the threshold level.

The measurement cannot operate properly because the trace has fallen completely below the threshold level. Change the threshold level to view signal.

Informational Invalid format: CSV files are not supported by this

measurement.

When utilizing the Phase Noise Personality: Option 226, the *.CSV file format is not available.

Informational Invalid EDGE burst timing.

The burst has manually been positioned off the display.

Informational Measurement halted. Press a measurement key to continue.

This error occurs after you choose

Cancel to refrain from setting the

attenuator to 0 dB during the Receive Channel Power and Receive Spur measurements.

Informational No Fast ADC hardware installed. Meas unavailable.

The analyzer cannot use sweep times of less than 5 milliseconds when Option B7D or Option AYX is not installed. Therefore the measurement will not be executed.

Informational Not enough frequency range to measure harmonics for channel.

Selected harmonics are above the frequency range of the analyzer.

Informational One or more harmonics beyond freq limit: number decreased.

The highest harmonic was beyond the frequency limit of the analyzer, so the number of measured harmonics was decreased.

Informational Option activated

This message is displayed after entering the selected option’s License Key.

Instrument Messages

Informational Please set RF input range (INPUT menu) to manual first.

In order to manually set the reference level and/or the attenuation under

Amplitude front-panel key, the RF Input Range menu under the Input

the front-panel key must be set to

Man (manual).

Informational Shutdown in process.

The analyzer is responding to the the shutdown procedure.

100 Chapter 1

Standby key selection, and is executing

Agilent E4445A Instrument Messages and Functional Tests

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

1 Instrument Messages

Instrument Messages Introduction

Error Queues

Error Message Format

Error Message Types

Instrument Messages

Error Messages

Instrument Messages Without Numbers