Agilent E4402B Programming Commands

Download

Page 1

Programming Commands

Agilent Technologies

ESA-E Series Spectrum Analyzers

cdmaOne Measurement Personality

This manual provides documentation for the following instruments:

ESA-E Series

E4402B (9 kHz - 3.0 GHz) E4404B (9 kHz - 6.7 GHz) E4405B (9 kHz - 13.2 GHz) E4407B (9 kHz - 26.5 GHz)

Manufacturing Part Number: E4401-90142

Printed in USA

March 2000

Page 2

The information contained in this document is subject to change without notice.

Agilent Technologies, Inc. makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and ﬁtness for a particular purpose. Agilent Technologies, Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Page 3

Contents

1. Programming Commands Cross Reference

Functional Index to SCPI Subsection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

2. Language Reference

CALCulate Subsystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Code Domain—Estimated Rho Lower Limit Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Code Domain—Relative Phase Upper Limit Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Code Domain—Estimated Rho Lower Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Code Domain—Relative Phase Upper Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Code Domain—Relative Timing Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

Code Domain—Relative Timing Upper Limit Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Channel Power—Lower Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

Channel Power—Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

Channel Power—Lower Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

Channel Power—Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7

Test Current Results Against all Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

Spur Close—Limit Deﬁnition Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

Spur Close—Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

Spurs at Harmonics—Upper Absolute Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

Spurs at Harmonics—Upper Relative Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

Spurs at Harmonics—Upper Absolute Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11

Spurs at Harmonics—Upper Relative Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11

Occupied Bandwidth—Emissions Bandwidth Lower Limit . . . . . . . . . . . . . . . . . . . . . . .2-11

Occupied Bandwidth—Emissions Bandwidth Lower Limit Test . . . . . . . . . . . . . . . . . . .2-12

Occupied Bandwidth—Emissions Bandwidth Upper Limit . . . . . . . . . . . . . . . . . . . . . . .2-13

Occupied Bandwidth—Emissions Bandwidth Upper Limit Test . . . . . . . . . . . . . . . . . . .2-14

Occupied Bandwidth—Occupied Bandwidth Lower Limit . . . . . . . . . . . . . . . . . . . . . . . .2-14

Occupied Bandwidth—Occupied Bandwidth Lower Limit Test . . . . . . . . . . . . . . . . . . . .2-15

Occupied Bandwidth—Occupied Bandwidth Upper Limit . . . . . . . . . . . . . . . . . . . . . . . .2-15

Occupied Bandwidth—Occupied Bandwidth Upper Limit Test . . . . . . . . . . . . . . . . . . . .2-16

Out of Band Spurious—Upper Absolute Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

Out of Band Spurious—Upper Relative Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

Out of Band Spurious—Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

Receive Channel Power—Lower Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

Receive Channel Power—Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

Receive Channel Power—Lower Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19

Receive Channel Power—Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20

Rho—Carrier Feedthrough Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20

Rho—Error Vector Magnitude Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21

Rho—Frequency Error Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21

Rho—Modulation Magnitude Error Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21

Rho—Modulation Phase Error Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-22

Rho—Rho Lower Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-22

Rho—Carrier Feedthrough Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23

Rho—Error Vector Magnitude Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23

Rho—Frequency Error Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24

Rho—Modulation Magnitude Error Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-25

Rho—Modulation Phase Error Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-26

Rho—Rho Lower Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-27

iii

Page 4

Contents

Rho—Time Offset Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

Rho—Time Offset Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29

Receiver Spurious—Receive Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29

Receiver Spurious—Receive Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

Receiver Spurious—Transmit Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

Receiver Spurious—Transmit Upper Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31

CONFigure Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32

DISPlay Subsystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33

Trace Y-Axis Amplitude Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33

Trace Y-Axis Reference Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33

FETCh Subsystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34

INITiate Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35

Continuous or Single Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35

Pause the Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35

Restart the Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36

Resume the Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36

INSTrument Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37

Select Application by Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37

Select Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38

MEASure Group of Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39

Measure Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39

Conﬁgure Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40

Fetch Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

Read Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

Code Domain Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42

Channel Power Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45

Spur Close Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46

Monitor Band/Channel Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47

Occupied Bandwidth Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48

Out of Band Spurious Emissions Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49

Receive Channel Power Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50

Rho (Waveform Quality) Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-51

Receiver Spurious Response Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54

Spurs at Harmonics Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55

MMEMory Subsystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

Store a Measurement Results in a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

READ Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-57

SENSe Subsystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58

Code Domain Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58

Digital Demod PN Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62

RF Channel Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62

RF Channel Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-63

Channel Power Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64

Correction for Base Station RF Port External Attenuation . . . . . . . . . . . . . . . . . . . . . . . 2-69

RF Noise Correction Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-69

RF Gain Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70

Spur Close—Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-71

Demodulation Synchronization Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-76

Demodulation Trigger Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-76

Page 5

Contents

Preampliﬁer Dialog Box Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-77

Center Frequency Step Size Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-77

Center Frequency Step Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-78

Temporary Center Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-78

Spurs at Harmonics Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-79

Monitor Band/Channel Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-84

Occupied Bandwidth Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-94

Out of Band Spurious Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-99

Reference Oscillator External Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-105

Reference Oscillator Rear Panel Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-105

Reference Oscillator Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-105

Carrier Power State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-106

Carrier Detection Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-106

Minimum Level of Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-107

RF Port Input Attenuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-107

RF Port Power Range Auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-107

Channel Bandwidth for cdmaOne Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-108

Radio Device Under Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-108

Radio Standard Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-109

Receive Channel Power Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-110

Rho (Waveform Quality) Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-115

Receiver Spurious Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-119

STATus Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-124

Operation Condition Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-124

Operation Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-124

Operation Event Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

Operation Negative Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

Operation Positive Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

SYSTem Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-126

System Conﬁguration Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-126

TRIGger Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

Rear Panel External Trigger Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

Rear Panel External Trigger Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

Frame Trigger Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

Frame Trigger Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-128

RF Burst Trigger Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-128

RF Burst Trigger Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-129

Page 6

Commands

Alphabetical Listing

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:ERHO:LOWer

[:DATA] <value>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:ERHO:LOWer

[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:PHASe[:UPPer]

[:DATA] <angle>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:PHASe[:UPPer]

[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:TIMing[:UPPer]

[:DATA] <time>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:TIMing[:UPPer]

[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

:CALCulate:CDPower:LIMit:ERHO:LOWer:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . .2-2

:CALCulate:CDPower:LIMit:ERHO:LOWer:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

:CALCulate:CDPower:LIMit:PHASe[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . .2-2

:CALCulate:CDPower:LIMit:PHASe[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

:CALCulate:CDPower:LIMit:TIMing[:UPPer]:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . .2-5

:CALCulate:CDPower:LIMit:TIMing[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower:LOWer

[:DATA] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower:LOWer

[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower[:UPPer][:DATA] <power> . . . . . . . .2-7

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower[:UPPer][:DATA]? . . . . . . . . . . . . . . .2-7

:CALCulate:CHPower:LIMit:CHPower:LOWer:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . .2-6

:CALCulate:CHPower:LIMit:CHPower:LOWer:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

:CALCulate:CHPower:LIMit:CHPower[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . .2-6

:CALCulate:CHPower:LIMit:CHPower[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

:CALCulate:CLIMits:FAIL? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

:CALCulate:CSPur:LIMit:SOURce STANdard|FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

:CALCulate:CSPur:LIMit:SOURce STANdard|FILE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

:CALCulate:CSPur:LIMit:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

:CALCulate:CSPur:LIMit:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:ABSolute

vii

Page 7

Commands

Alphabetical Listing

[:UPPer][:DATA] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:ABSolute

[:UPPer][:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:RELative

[:UPPer][:DATA] <rel_power>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:RELative

[:UPPer][:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

:CALCulate:HARMonics:LIMit:ABSolute[:UPPer]:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . . 2-11

:CALCulate:HARMonics:LIMit:ABSolute[:UPPer]:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

:CALCulate:HARMonics:LIMit:RELative[:UPPer]:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . . 2-11

:CALCulate:HARMonics:LIMit:RELative[:UPPer]:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth:LOWer

[:DATA] <frequency>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth:LOWer

[:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth[:UPPer]

[:DATA] <frequency>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth[:UPPer]

[:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS

[:OBWidth]:LOWer[:DATA] <frequency> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS

[:OBWidth]:LOWer[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS

[:OBWidth][:UPPer][:DATA] <frequency> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS

[:OBWidth][:UPPer][:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15

:CALCulate:OBWidth:LIMit:EBWidth:LOWer:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . 2-12

:CALCulate:OBWidth:LIMit:EBWidth:LOWer:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

:CALCulate:OBWidth:LIMit:EBWidth[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . 2-14

:CALCulate:OBWidth:LIMit:EBWidth[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

:CALCulate:OBWidth:LIMit[:OBWidth]:LOWer:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . 2-15

:CALCulate:OBWidth:LIMit[:OBWidth]:LOWer:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

:CALCulate:OBWidth:LIMit[:OBWidth][:UPPer]:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . 2-16

:CALCulate:OBWidth:LIMit[:OBWidth][:UPPer]:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

viii

Page 8

Commands

Alphabetical Listing

:CALCulate:OOBSpur:LIMit:TABLe:ABSolute[:UPPer][:DATA] <power1,

power2, …, powerN>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

:CALCulate:OOBSpur:LIMit:TABLe:ABSolute[:UPPer][:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . .2-17

:CALCulate:OOBSpur:LIMit:TABLe:RELative[:UPPer][:DATA] <rel_power1,

rel_power2, …, rel_powerN> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

:CALCulate:OOBSpur:LIMit:TABLe:RELative[:UPPer][:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . .2-17

:CALCulate:OOBSpur:LIMit:TABLe:TYPE

<value1, value2, …, valueN> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

:CALCulate:OOBSpur:LIMit:TABLe:TYPE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower

:LOWer[:DATA] <value> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower

:LOWer[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower

:UPPer[:DATA] <value> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower

:UPPer[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20

:CALCulate:RCHPower:LIMit:RCHPower:LOWer:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . .2-18

:CALCulate:RCHPower:LIMit:RCHPower:LOWer:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

:CALCulate:RCHPower:LIMit:RCHPower[:UPPer]:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . .2-18

:CALCulate:RCHPower:LIMit:RCHPower[:UPPer]:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

:CALCulate:RHO:LIMit:<standard>:BS|BTS:CFTHrough:[UPPer[

[:DATA] <rel_power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23

:CALCulate:RHO:LIMit:<standard>:BS|BTS:CFTHrough:[UPPer[

[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23

:CALCulate:RHO:LIMit:<standard>:BS|BTS:EVM[:UPPer][:DATA] <percentage>. . . . . . . . . . .2-23

:CALCulate:RHO:LIMit:<standard>:BS|BTS:EVM[:UPPer][:DATA]?. . . . . . . . . . . . . . . . . . . . . .2-23

:CALCulate:RHO:LIMit:<standard>:BS|BTS:FERRor[:UPPer]

[:DATA] <frequency> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24

:CALCulate:RHO:LIMit:<standard>:BS|BTS:FERRor[:UPPer]

[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24

:CALCulate:RHO:LIMit:<standard>:BS|BTS:MAGNitude[:UPPer]

[:DATA] <percentage> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-25

:CALCulate:RHO:LIMit:<standard>:BS|BTS:MAGNitude[:UPPer]

[:DATA]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-25

:CALCulate:RHO:LIMit:<standard>:BS|BTS:PHASe[:UPPer]

Page 9

Commands

Alphabetical Listing

[:DATA] <angle>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-26

:CALCulate:RHO:LIMit:<standard>:BS|BTS:PHASe[:UPPer]

[:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26

:CALCulate:RHO:LIMit:<standard>:BS|BTS:RHO:LOWer[:DATA] <parameter> . . . . . . . . . . . 2-27

:CALCulate:RHO:LIMit:<standard>:BS|BTS:RHO:LOWer[:DATA]? . . . . . . . . . . . . . . . . . . . . . . 2-27

:CALCulate:RHO:LIMit:<standard>:BS|BTS:TOFFset[:UPPer]

[:DATA] <time> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

:CALCulate:RHO:LIMit:<standard>:BS|BTS:TOFFset[:UPPer]

[:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

:CALCulate:RHO:LIMit:CFTHrough[:UPPer[:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . 2-20

:CALCulate:RHO:LIMit:CFTHrough[:UPPer[:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

:CALCulate:RHO:LIMit:EVM[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

:CALCulate:RHO:LIMit:EVM[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

:CALCulate:RHO:LIMit:FERRor[:UPPer]:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

:CALCulate:RHO:LIMit:FERRor[:UPPer]:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

:CALCulate:RHO:LIMit:MAGNitude[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . 2-21

:CALCulate:RHO:LIMit:MAGNitude[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

:CALCulate:RHO:LIMit:PHASe[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

:CALCulate:RHO:LIMit:PHASe[:UPPer]:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

:CALCulate:RHO:LIMit:RHO:LOWer:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

:CALCulate:RHO:LIMit:RHO:LOWer:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

:CALCulate:RHO:LIMit:TOFFset[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . 2-29

:CALCulate:RHO:LIMit:TOFFset[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:RECeive[:UPPer]

[:DATA] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-29

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:RECeive[:UPPer]

[:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:TRANsmit[:UPPer]

[:DATA] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-30

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:TRANsmit[:UPPer]

[:DATA]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

:CALCulate:RSPur:LIMit:RECeive[:UPPer]:STATe OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . 2-30

:CALCulate:RSPur:LIMit:RECeive[:UPPer]:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-30

:CALCulate:RSPur:LIMit:TRANsmit[:UPPer]:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . 2-31

Page 10

Commands

Alphabetical Listing

:CALCulate:RSPur:LIMit:TRANsmit[:UPPer]:STATe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-31

:CONFigure:<measurement>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-32

:CONFigure:<measurement>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-40

:CONFigure:CDPower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-42

:CONFigure:CHPower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-45

:CONFigure:CSPur. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-46

:CONFigure:HARMonics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-55

:CONFigure:MONitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-47

:CONFigure:OBW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-48

:CONFigure:OOBSpur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-49

:CONFigure:RCHPower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-50

:CONFigure:RHO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-51

:CONFigure:RSPur. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-54

:DISPlay:WINDow:TRACe:Y[:SCALe]:PDIVision <rel_ampl> . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-33

:DISPlay:WINDow:TRACe:Y[:SCALe]:PDIVision?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-33

:DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVel <ampl>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-33

:DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVel?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-33

:FETCh:<measurement>[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-34

:FETCh:<measurement>[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-41

:FETCh:CDPower[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-42

:FETCh:CHPower[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-45

:FETCh:CSPur[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-46

:FETCh:HARMonics[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-55

:FETCh:MONitor[n] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-47

:FETCh:OBW[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-48

:FETCh:OOBSpur[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-49

:FETCh:RCHPower[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-50

:FETCh:RHO[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-51

:FETCh:RSPur[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-54

:INITiate:CONTinuous OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-35

:INITiate:CONTinuous?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-35

Page 11

Commands

Alphabetical Listing

:INITiate:PAUSe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35

:INITiate:RESTart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36

:INITiate:RESume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36

:INSTrument:NSELect <integer>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37

:INSTrument:NSELect?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37

:INSTrument[:SELect] ‘SA’|’CDMA’ (application speciﬁc mode) . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38

:INSTrument[:SELect]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38

:MEASure:<measurement>[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39

:MEASure:CDPower[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42

:MEASure:CHPower[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45

:MEASure:CSPur[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46

:MEASure:HARMonics[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55

:MEASure:MONitor[n]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47

:MEASure:OBW[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-48

:MEASure:OOBSpur[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49

:MEASure:RCHPower[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-50

:MEASure:RHO[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-51

:MEASure:RSPur[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54

:MMEMory:STORe:RESults ﬁlename.csv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

:READ:<measurement>[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

:READ:<measurement>[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-57

:READ:CDPower[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-42

:READ:CHPower[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45

:READ:CSPur[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46

:READ:HARMonics[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55

:READ:MONitor[n] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47

:READ:OBW[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48

:READ:OOBSpur[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49

:READ:RCHPower[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50

:READ:RHO[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-51

:READ:RSPur[n]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54

xii

Page 12

Commands

Alphabetical Listing

:STATus:OPERation:CONDition? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-124

:STATus:OPERation:ENABle <number> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-124

:STATus:OPERation:ENABle?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-124

:STATus:OPERation:NTRansition <number> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

:STATus:OPERation:NTRansition?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

:STATus:OPERation:PTRansition <number>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

:STATus:OPERation:PTRansition? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

:STATus:OPERation[:EVENt]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-125

:SYSTem:CONFigure:MODE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-126

:TRIGger:FRAMe:DELay <time> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

:TRIGger:FRAMe:DELay? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

:TRIGger[:SEQuence]:EXTernal:DELay <time> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

:TRIGger[:SEQuence]:EXTernal:DELay? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

:TRIGger[:SEQuence]:EXTernal:SLOPe POSitive|NEGative. . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

:TRIGger[:SEQuence]:EXTernal:SLOPe? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-127

:TRIGger[:SEQuence]:FRAMe:PERiod <time>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-128

:TRIGger[:SEQuence]:FRAMe:PERiod? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-128

:TRIGger[:SEQuence]:RFBurst:DELay <time> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-128

:TRIGger[:SEQuence]:RFBurst:DELay? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-128

:TRIGger[:SEQuence]:RFBurst:LEVel <percent>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-129

:TRIGger[:SEQuence]:RFBurst:LEVel?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-129

[:SENSe]:CDPower:ASET:THReshold <rel_power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-59

[:SENSe]:CDPower:ASET:THReshold? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-59

[:SENSe]:CDPower:AVERage:COUNt <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-58

[:SENSe]:CDPower:AVERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-58

[:SENSe]:CDPower:AVERage:TCONtrol EXPonential|REPeat . . . . . . . . . . . . . . . . . . . . . . . . . . .2-59

[:SENSe]:CDPower:AVERage:TCONtrol? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-59

[:SENSe]:CDPower:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-58

[:SENSe]:CDPower:AVERage[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-58

[:SENSe]:CDPower:METHod POWer|TPHase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-60

[:SENSe]:CDPower:METHod? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-60

xiii

Page 13

Commands

Alphabetical Listing

[:SENSe]:CDPower:MIXer:RANGe[:UPPer] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59

[:SENSe]:CDPower:MIXer:RANGe[:UPPer]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59

[:SENSe]:CDPower:SPECtrum NORMal|INVert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60

[:SENSe]:CDPower:SPECtrum? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60

[:SENSe]:CDPower:SWEep:TIME <time> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61

[:SENSe]:CDPower:SWEep:TIME?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61

[:SENSe]:CHANnel:PNOFfset <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62

[:SENSe]:CHANnel:PNOFfset?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62

[:SENSe]:CHANnel:RFCHannel:FREQuency <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62

[:SENSe]:CHANnel:RFCHannel:FREQuency? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62

[:SENSe]:CHANnel:RFCHannel[:NUMBer] <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-63

[:SENSe]:CHANnel:RFCHannel[:NUMBer]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-63

[:SENSe]:CHPower:AVERage:COUNt <integer>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64

[:SENSe]:CHPower:AVERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64

[:SENSe]:CHPower:AVERage:TCONtrol EXPonential|REPeat. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65

[:SENSe]:CHPower:AVERage:TCONtrol? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65

[:SENSe]:CHPower:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64

[:SENSe]:CHPower:AVERage[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64

[:SENSe]:CHPower:BANDwidth|BWIDth:INTegration <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65

[:SENSe]:CHPower:BANDwidth|BWIDth:INTegration? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65

[:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution] <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66

[:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution]:AUTO OFF|ON|0|1 . . . . . . . . . . . . . .2-66

[:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution]:AUTO? . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66

[:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66

[:SENSe]:CHPower:CORRection:NOISe[:AUTO] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67

[:SENSe]:CHPower:CORRection:NOISe[:AUTO]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67

[:SENSe]:CHPower:FREQuency:SPAN <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66

[:SENSe]:CHPower:FREQuency:SPAN?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66

[:SENSe]:CHPower:MIXer:RANGe[:UPPer] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67

[:SENSe]:CHPower:MIXer:RANGe[:UPPer]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67

[:SENSe]:CHPower:TRIGger:SOURce EXTernal|IMMediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-68

xiv

Page 14

Commands

Alphabetical Listing

[:SENSe]:CHPower:TRIGger:SOURce?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-68

[:SENSe]:CORRection:BS[:RF]:LOSS <rel_power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-69

[:SENSe]:CORRection:BS[:RF]:LOSS? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-69

[:SENSe]:CORRection:NOISe:THReshold <rel_power>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-69

[:SENSe]:CORRection:NOISe:THReshold?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-69

[:SENSe]:CORRection[:RF]:GAIN <rel_power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-70

[:SENSe]:CORRection[:RF]:GAIN? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-70

[:SENSe]:CSPur:AVERage:COUNt <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-71

[:SENSe]:CSPur:AVERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-71

[:SENSe]:CSPur:AVERage:TCONtrol EXPonential|REPeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-72

[:SENSe]:CSPur:AVERage:TCONtrol? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-72

[:SENSe]:CSPur:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-71

[:SENSe]:CSPur:AVERage[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-71

[:SENSe]:CSPur:BANDwidth|BWIDth:VIDeo <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-73

[:SENSe]:CSPur:BANDwidth|BWIDth:VIDeo? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-73

[:SENSe]:CSPur:BANDwidth|BWIDth[:RESolution] <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-73

[:SENSe]:CSPur:BANDwidth|BWIDth[:RESolution]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-73

[:SENSe]:CSPur:DETector[:FUNCtion] POSitive|NEGative|SAMPle . . . . . . . . . . . . . . . . . . . . .2-74

[:SENSe]:CSPur:DETector[:FUNCtion]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-74

[:SENSe]:CSPur:MIXer:RANGe[:UPPer] <power>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-74

[:SENSe]:CSPur:MIXer:RANGe[:UPPer]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-74

[:SENSe]:CSPur:TRIGger:SOURce EXTernal|IMMediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-75

[:SENSe]:CSPur:TRIGger:SOURce? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-75

[:SENSe]:CSPur:TYPE EXAMine|FULL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-72

[:SENSe]:CSPur:TYPE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-72

[:SENSe]:DEMod:SYNC ESEC|NONE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-76

[:SENSe]:DEMod:SYNC? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-76

[:SENSe]:DEMod:TRIGger:SOURce EXTernal|FRAMe|IMMediate|RFBurst. . . . . . . . . . . . . . .2-76

[:SENSe]:DEMod:TRIGger:SOURce? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-76

[:SENSe]:DIALog:PAMPliﬁer[:STATe] OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-77

[:SENSe]:DIALog:PAMPliﬁer[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-77

Page 15

Commands

Alphabetical Listing

[:SENSe]:FREQuency:CENTer:STEP:AUTO OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-77

[:SENSe]:FREQuency:CENTer:STEP:AUTO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-77

[:SENSe]:FREQuency:CENTer:STEP[:INCRement] <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-78

[:SENSe]:FREQuency:CENTer:STEP[:INCRement]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78

[:SENSe]:FREQuency:CENTer:TEMPorary <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78

[:SENSe]:FREQuency:CENTer:TEMPorary? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78

[:SENSe]:HARMonics:AVERage:COUNt <integer>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79

[:SENSe]:HARMonics:AVERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79

[:SENSe]:HARMonics:AVERage:TCONtrol EXPonential|REPeat. . . . . . . . . . . . . . . . . . . . . . . . . 2-79

[:SENSe]:HARMonics:AVERage:TCONtrol? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79

[:SENSe]:HARMonics:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79

[:SENSe]:HARMonics:AVERage[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79

[:SENSe]:HARMonics:BANDwidth|:BWIDth:RESolution <freq> . . . . . . . . . . . . . . . . . . . . . . . . . 2-80

[:SENSe]:HARMonics:BANDwidth|:BWIDth:RESolution? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80

[:SENSe]:HARMonics:BANDwidth|:BWIDth:VIDeo <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80

[:SENSe]:HARMonics:BANDwidth|:BWIDth:VIDeo?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80

[:SENSe]:HARMonics:BANDwidth|BWIDth:VIDeo:AUTO OFF|ON|0|1. . . . . . . . . . . . . . . . . . 2-81

[:SENSe]:HARMonics:BANDwidth|BWIDth:VIDeo:AUTO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-81

[:SENSe]:HARMonics:DETector POSitive|NEGative|SAMPle. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-81

[:SENSe]:HARMonics:DETector? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-81

[:SENSe]:HARMonics:MIXer:RANGe[:UPPer] <power>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82

[:SENSe]:HARMonics:MIXer:RANGe[:UPPer]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82

[:SENSe]:HARMonics:NUMBer <integer>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82

[:SENSe]:HARMonics:NUMBer?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82

[:SENSe]:HARMonics:SWEep:TIME <time> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82

[:SENSe]:HARMonics:SWEep:TIME?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82

[:SENSe]:HARMonics:TRIGger:SOURce EXTernal|IMMediate . . . . . . . . . . . . . . . . . . . . . . . . . . 2-83

[:SENSe]:HARMonics:TRIGger:SOURce? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-83

[:SENSe]:MONitor:AVERage:COUNt <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-84

[:SENSe]:MONitor:AVERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-84

[:SENSe]:MONitor:AVERage:TCONtrol EXPonential|REPeat . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-84

xvi

Page 16

Commands

Alphabetical Listing

[:SENSe]:MONitor:AVERage:TCONtrol? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-84

[:SENSe]:MONitor:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-84

[:SENSe]:MONitor:AVERage[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-84

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth:VIDeo <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . .2-86

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth:VIDeo:AUTO OFF|ON|0|1. . . . . . . . . . . . . . .2-86

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth:VIDeo:AUTO? . . . . . . . . . . . . . . . . . . . . . . . . . .2-86

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth:VIDeo? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-86

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth[:RESolution] <freq> . . . . . . . . . . . . . . . . . . . . .2-85

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth[:RESolution]:AUTO OFF|ON|0|1 . . . . . . . . .2-86

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth[:RESolution]:AUTO?. . . . . . . . . . . . . . . . . . . . .2-86

[:SENSe]:MONitor:BAND:BANDwidth|BWIDth[:RESolution]? . . . . . . . . . . . . . . . . . . . . . . . . . .2-85

[:SENSe]:MONitor:BAND:BLOCk <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-87

[:SENSe]:MONitor:BAND:BLOCk?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-87

[:SENSe]:MONitor:BAND:DETector POSitive|SAMPle|NEGative. . . . . . . . . . . . . . . . . . . . . . . .2-88

[:SENSe]:MONitor:BAND:DETector? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-88

[:SENSe]:MONitor:BAND:MAXHold[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-88

[:SENSe]:MONitor:BAND:MAXHold[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-88

[:SENSe]:MONitor:BAND:PRGain[:STATe] OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-89

[:SENSe]:MONitor:BAND:PRGain[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-89

[:SENSe]:MONitor:BAND:SPAN <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-89

[:SENSe]:MONitor:BAND:SPAN? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-89

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth:VIDeo <freq> . . . . . . . . . . . . . . . . . . . . . . . .2-91

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth:VIDeo

:AUTO OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-91

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth:VIDeo

:AUTO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-91

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth:VIDeo? . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-91

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth[:RESolution] <freq>. . . . . . . . . . . . . . . . . . .2-90

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth[:RESolution]

:AUTO OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-90

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth[:RESolution]

:AUTO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-90

xvii

Page 17

Commands

Alphabetical Listing

[:SENSe]:MONitor:CHANnel:BANDwidth|BWIDth[:RESolution]? . . . . . . . . . . . . . . . . . . . . . . . 2-90

[:SENSe]:MONitor:CHANnel:DETector POSitive|SAMPle|NEGative. . . . . . . . . . . . . . . . . . . . . 2-92

[:SENSe]:MONitor:CHANnel:DETector? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-92

[:SENSe]:MONitor:CHANnel:MAXHold[:STATe] OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . 2-92

[:SENSe]:MONitor:CHANnel:MAXHold[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-92

[:SENSe]:MONitor:CHANnel:PRGain[:STATe] OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-92

[:SENSe]:MONitor:CHANnel:PRGain[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-92

[:SENSe]:MONitor:CHANnel:SPAN <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93

[:SENSe]:MONitor:CHANnel:SPAN?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93

[:SENSe]:MONitor:FBAND TRANsmit|RECeive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-89

[:SENSe]:MONitor:FBAND? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-89

[:SENSe]:MONitor:METHod CHANnel|BAND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93

[:SENSe]:MONitor:METHod? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93

[:SENSe]:OBWidth:AVERage:COUNt <integer>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94

[:SENSe]:OBWidth:AVERage:COUNt?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94

[:SENSe]:OBWidth:AVERage:TCONtrol EXPonential|REPeat. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-95

[:SENSe]:OBWidth:AVERage:TCONtrol?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-95

[:SENSe]:OBWidth:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94

[:SENSe]:OBWidth:AVERage[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94

[:SENSe]:OBWidth:BANDwidth|BWIDth:VIDeo <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96

[:SENSe]:OBWidth:BANDwidth|BWIDth:VIDeo? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96

[:SENSe]:OBWidth:BANDwidth|BWIDth[:RESolution] <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-95

[:SENSe]:OBWidth:BANDwidth|BWIDth[:RESolution]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-95

[:SENSe]:OBWidth:DETector[:FUNCtion] POSitive|NEGative|SAMPle. . . . . . . . . . . . . . . . . . . 2-96

[:SENSe]:OBWidth:DETector[:FUNCtion]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96

[:SENSe]:OBWidth:EBWidth:XDB <rel_power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-96

[:SENSe]:OBWidth:EBWidth:XDB? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96

[:SENSe]:OBWidth:MAXHold[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-97

[:SENSe]:OBWidth:MAXHold[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-97

[:SENSe]:OBWidth:MIXer:RANGe[:UPPer] <power>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-97

[:SENSe]:OBWidth:MIXer:RANGe[:UPPer]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-97

xviii

Page 18

Commands

Alphabetical Listing

[:SENSe]:OBWidth:PERCent <number>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-98

[:SENSe]:OBWidth:PERCent?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-98

[:SENSe]:OBWidth:TRIGger:SOURce EXTernal|IMMediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-98

[:SENSe]:OBWidth:TRIGger:SOURce?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-98

[:SENSe]:OOBSpur:AVERage:COUNt <integer>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-99

[:SENSe]:OOBSpur:AVERage:COUNt?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-99

[:SENSe]:OOBSpur:AVERage:TCONtrol EXPonential|REPeat . . . . . . . . . . . . . . . . . . . . . . . . . .2-100

[:SENSe]:OOBSpur:AVERage:TCONtrol?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-100

[:SENSe]:OOBSpur:AVERage[:STATe] OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-99

[:SENSe]:OOBSpur:AVERage[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-99

[:SENSe]:OOBSpur:MIXer:RANGe[:UPPer] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-100

[:SENSe]:OOBSpur:MIXer:RANGe[:UPPer]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-100

[:SENSe]:OOBSpur:OVRSweep:FACTor <value>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-101

[:SENSe]:OOBSpur:OVRSweep:FACTor? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-101

[:SENSe]:OOBSpur:OVRSweep[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-100

[:SENSe]:OOBSpur:OVRSweep[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-100

[:SENSe]:OOBSpur:SPRange <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-101

[:SENSe]:OOBSpur:SPRange?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-101

[:SENSe]:OOBSpur:TABLe:BANDwidth|BWIDth:RESolution <bw1, bw2, …, bwN> . . . . . . . .2-101

[:SENSe]:OOBSpur:TABLe:BANDwidth|BWIDth:RESolution?. . . . . . . . . . . . . . . . . . . . . . . . . .2-101

[:SENSe]:OOBSpur:TABLe:BANDwidth|BWIDth:VIDeo <bw1, bw2, …, bwN>. . . . . . . . . . . . .2-102

[:SENSe]:OOBSpur:TABLe:BANDwidth|BWIDth:VIDeo?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-102

[:SENSe]:OOBSpur:TABLe:CFRequency <freq1, freq2, …, freqN> . . . . . . . . . . . . . . . . . . . . . . .2-102

[:SENSe]:OOBSpur:TABLe:CFRequency? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-102

[:SENSe]:OOBSpur:TABLe:DETector POSitive|SAMPle|NEGative. . . . . . . . . . . . . . . . . . . . . .2-103

[:SENSe]:OOBSpur:TABLe:DETector? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-103

[:SENSe]:OOBSpur:TABLe:FREQuency:SPAN <freq1, freq2, …, freqN> . . . . . . . . . . . . . . . . . .2-103

[:SENSe]:OOBSpur:TABLe:FREQuency:SPAN? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-103

[:SENSe]:OOBSpur:TRIGger:SOURce EXTernal|IMMediate. . . . . . . . . . . . . . . . . . . . . . . . . . . .2-103

[:SENSe]:OOBSpur:TRIGger:SOURce?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-103

[:SENSe]:OPTion:ROSCillator:EXTernal:FREQuency <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . . .2-105

xix

Page 19

Commands

Alphabetical Listing

[:SENSe]:OPTion:ROSCillator:EXTernal:FREQuency? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-105

[:SENSe]:OPTion:ROSCillator:OUTPut? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-105

[:SENSe]:OPTion:ROSCillator:OUTPut[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . 2-105

[:SENSe]:OPTion:ROSCillator:SOURce INTernal|EXTernal. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-105

[:SENSe]:OPTion:ROSCillator:SOURce? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-105

[:SENSe]:POWer:CARRier:STATe OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-106

[:SENSe]:POWer:CARRier:STATe?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-106

[:SENSe]:POWer:CTHReshold <power>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-106

[:SENSe]:POWer:CTHReshold?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-106

[:SENSe]:POWer:LEVel:MINimum <power>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-107

[:SENSe]:POWer:LEVel:MINimum?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-107

[:SENSe]:POWer[:RF]:ATTenuation <rel_power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-107

[:SENSe]:POWer[:RF]:ATTenuation? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-107

[:SENSe]:POWer[:RF]:RANGe:AUTO OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-107

[:SENSe]:POWer[:RF]:RANGe:AUTO?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-107

[:SENSe]:RADio:BANDwidth|BWIDth <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-108

[:SENSe]:RADio:BANDwidth|BWIDth? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-108

[:SENSe]:RADio:DEVice BS|MS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-108

[:SENSe]:RADio:DEVice? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-108

[:SENSe]:RADio:STANdard:BAND ARIBT53|C95B|C95C|CKOR|IS95A|JSTD8|

P95B|P95C|PKOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-109

[:SENSe]:RADio:STANdard:BAND?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-109

[:SENSe]:RCHPower:AVERage:COUNt <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-110

[:SENSe]:RCHPower:AVERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-110

[:SENSe]:RCHPower:AVERage:TCONtrol EXPonential|REPeat. . . . . . . . . . . . . . . . . . . . . . . . .2-110

[:SENSe]:RCHPower:AVERage:TCONtrol? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-110

[:SENSe]:RCHPower:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-110

[:SENSe]:RCHPower:AVERage[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-110

[:SENSe]:RCHPower:BANDwidth|BWIDth:INTegration <freq>. . . . . . . . . . . . . . . . . . . . . . . . . 2-111

[:SENSe]:RCHPower:BANDwidth|BWIDth:INTegration? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-111

[:SENSe]:RCHPower:BANDwidth|BWIDth[:RESolution] <freq> . . . . . . . . . . . . . . . . . . . . . . . . 2-111

Page 20

Commands

Alphabetical Listing

[:SENSe]:RCHPower:BANDwidth|BWIDth[:RESolution]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-111

[:SENSe]:RCHPower:CORRection:NOISe[:AUTO] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . .2-112

[:SENSe]:RCHPower:CORRection:NOISe[:AUTO]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-112

[:SENSe]:RCHPower:FREQuency:SPAN <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-112

[:SENSe]:RCHPower:FREQuency:SPAN?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-112

[:SENSe]:RCHPower:MIXer:RANGe[:UPPer] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-113

[:SENSe]:RCHPower:MIXer:RANGe[:UPPer]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-113

[:SENSe]:RCHPower:PRGain[:STATe] OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-113

[:SENSe]:RCHPower:PRGain[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-113

[:SENSe]:RCHPower:TRIGger:SOURce EXTernal|IMMediate . . . . . . . . . . . . . . . . . . . . . . . . . .2-113

[:SENSe]:RCHPower:TRIGger:SOURce? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-113

[:SENSe]:RHO:AVERage:COUNt <integer>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-115

[:SENSe]:RHO:AVERage:COUNt?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-115

[:SENSe]:RHO:AVERage:TCONtrol EXPonential|REPeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-115

[:SENSe]:RHO:AVERage:TCONtrol?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-116

[:SENSe]:RHO:AVERage[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-115

[:SENSe]:RHO:AVERage[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-115

[:SENSe]:RHO:DISPlay:DOTS OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-116

[:SENSe]:RHO:DISPlay:DOTS?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-116

[:SENSe]:RHO:DISPlay:LENGth <value> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-116

[:SENSe]:RHO:DISPlay:LENGth?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-116

[:SENSe]:RHO:MIXer:RANGe[:UPPer] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-117

[:SENSe]:RHO:MIXer:RANGe[:UPPer]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-117

[:SENSe]:RHO:NSPC ONE|TWO|FOUR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-117

[:SENSe]:RHO:NSPC? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-117

[:SENSe]:RHO:SPECtrum NORMal|INVert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-118

[:SENSe]:RHO:SPECtrum? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-118

[:SENSe]:RHO:SWEep:TIME <time> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-118

[:SENSe]:RHO:SWEep:TIME?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-118

[:SENSe]:RSPur:AVERage:COUNt <integer> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-119

[:SENSe]:RSPur:AVERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-119

xxi

Page 21

Commands

Alphabetical Listing

[:SENSe]:RSPur:AVERage:TCONtrol EXPonential|REPeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120

[:SENSe]:RSPur:AVERage:TCONtrol? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120

[:SENSe]:RSPur:AVERage[:STATe] OFF|ON|0|1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-119

[:SENSe]:RSPur:AVERage[:STATe]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-119

[:SENSe]:RSPur:BANDwidth|BWIDth:VIDeo <freq> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120

[:SENSe]:RSPur:BANDwidth|BWIDth:VIDeo?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-121

[:SENSe]:RSPur:BANDwidth|BWIDth[:RESolution] <freq>. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120

[:SENSe]:RSPur:BANDwidth|BWIDth[:RESolution]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120

[:SENSe]:RSPur:BLOCk <value> (Tuning Plan Dependent) . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-121

[:SENSe]:RSPur:BLOCk? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-121

[:SENSe]:RSPur:DETector[:FUNCtion] POSitive|NEGative|SAMPle. . . . . . . . . . . . . . . . . . . . 2-122

[:SENSe]:RSPur:DETector[:FUNCtion]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-122

[:SENSe]:RSPur:FBANd TRANsmit|RECeive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-121

[:SENSe]:RSPur:FBANd? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-121

[:SENSe]:RSPur:MIXer:RANGe[:UPPer] <power> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-122

[:SENSe]:RSPur:MIXer:RANGe[:UPPer]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-122

[:SENSe]:RSPur:PRGain[:STATe] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-123

[:SENSe]:RSPur:PRGain[:STATe]?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-123

[:SENSe]:RSPur:TRIGger:SOURce EXTernal|IMMediate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-123

[:SENSe]:RSPur:TRIGger:SOURce?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-123

xxii

Page 22

1 Programming Commands Cross

Reference

1-1

Page 23

Programming Commands Cross Reference Functional Index to SCPI Subsection

Functional Index to SCPI Subsection

The following table lists the SCPI subsystems or subsections associated with the instrument cdmaOne function categories. The commands listed are for cdmaOne speciﬁc functions. These commands are documented in Chapter 2 , “Language Reference.” If you require information on the commands for the Agilent ESA Spectrum Analyzers, refer to the Agilent ESA Spectrum Analyzers Programmer’s Guide.

Function Category

ATTENUATOR see function category: Internal Attenuation BANDWIDTH :CALCulate

CONFIGURATION and STATUS

CORRECTED MEASUREMENTS

LOAD or SAVE :MMEMory

SCPI Subsection or Subsystem

:SYSTem

[:SENSe]:CORRection

DEMODULATION [:SENSe]:DEMod DISPLAY :DISPlay:WINDow FREQUENCY [:SENSe]:OOBSpur:TABLe:CFRequency

[:SENSe]:OPTion:ROSCillator:EXTernal:FREQuency [:SENSe]:Frequency[:CENTer] [:SENSe]:CHANnel:FRCHannel:FREQuency

FREQUENCY SPAN

INTERNAL ATTENUATION

1-2 Chapter1

[:SENSe]:FREQuency [:SENSe]:CHPower:FREQuency:SPAN [:SENSe]:MONitor:BAND:FREQuency:SPAN [:SENSe]:MONitor:CHANnel:FREQuency:SPAN [:SENSe]:RCHPower:FREQuency:SPAN

[:SENSe]:POWer

Page 24

Programming Commands Cross Reference

Functional Index to SCPI Subsection

Function Category

LIMITS :CALCulate MEASURE :CONFigure

SWEEP [:SENSe]:CDPower:SWEep

TRACE :DISPlay TRIGGER [:SENSe]:<measurmenr>:TRIGger

SCPI Subsection or Subsystem

:FETCh :MEASure :READ [:SENSe]:CHPower [:SENSe]:CSPur [:SENSe]:HARMonics [:SENSe]:MONitor:BAND [:SENSe]:MONitor:CHANnel [:SENSe]:OBWidth [:SENSe]:OOBSpur [:SENSe]:RCHPower [:SENSe]:RSPur [:SENSe]:RHO

[:SENSe]:SWEep

Chapter 1 1-3

Page 25

Programming Commands Cross Reference Functional Index to SCPI Subsection

1-4 Chapter1

Page 26

2 Language Reference

These commands are only available when the cdmaOne mode has been selected using INSTrument:SELect or INSTrument:NSELect. If cdmaOne mode is selected, commands that are unique to another mode are not available.

2-1

Page 27

Language Reference

CALCulate Subsystem

This subsystem is used to perform post-acquisition data processing. In effect, the collection of new data triggers the CALCulate subsystem. In this instrument, the primary functions in this subsystem are markers and limits.

Code Domain—Estimated Rho Lower Limit Testing

:CALCulate:CDPower:LIMit:ERHO:LOWer:STATe OFF|ON|0|1 :CALCulate:CDPower:LIMit:ERHO:LOWer:STATe?

Turn the estimated rho lower pass/fail limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Code Domain—Relative Phase Upper Limit Testing

:CALCulate:CDPower:LIMit:PHASe[:UPPer]:STATe OFF|ON|0|1 :CALCulate:CDPower:LIMit:PHASe[:UPPer]:STATe?

Turn the relative phase upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

2-2 Chapter2

Page 28

Language Reference

CALCulate Subsystem

Code Domain—Estimated Rho Lower Limit

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:ERHO:LOWer [:DATA] <value>

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:ERHO:LOWer [:DATA]?

Set the lower limit for code-domain estimated rho pass/fail test.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 0.912—All standards

Range: 0 to 1.0 Default Unit: None Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Code Domain—Relative Phase Upper Limit

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:PHASe[:UPPer] [:DATA] <angle>

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:PHASe[:UPPer] [:DATA]?

Set the upper limit, in radians for code-domain relative phase testing. The absolute values of the relative phase measurement results are tested against this value.

Chapter 2 2-3

Page 29

Language Reference

CALCulate Subsystem

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST:

IS95A, JSTD8, CKOR, PKOR C95B, P95B, C95C, P95C, ARIB T53

0.05 mRad 0.15 mRad

Range: −3.1459 to 3.1459 Default Unit: Rad Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Code Domain—Relative Timing Upper Limit

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:TIMing[:UPPer] [:DATA] <time>

:CALCulate:CDPower:LIMit:<standard>:BS|BTS:TIMing[:UPPer] [:DATA]?

Set the upper limit, in seconds, for code-domain relative timing testing. The absolute values of the relative timing measurement results are tested against this value.

BS = Base Station

2-4 Chapter2

Page 30

BTS = Base Transceiver Station BS = BTS

Available Standards

Language Reference

CALCulate Subsystem

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 10 µs—All standards

Range: −26.7 ms to 26.7 ms Default Unit: sec Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Code Domain—Relative Timing Upper Limit Testing

:CALCulate:CDPower:LIMit:TIMing[:UPPer]:STATe OFF|ON|0|1 :CALCulate:CDPower:LIMit:TIMing[:UPPer]:STATe?

Turn relative timing upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Chapter 2 2-5

Meas Setup, More, Limits…

Page 31

Language Reference

CALCulate Subsystem

Channel Power—Lower Limit Test

:CALCulate:CHPower:LIMit:CHPower:LOWer:STATe OFF|ON|0|1 :CALCulate:CHPower:LIMit:CHPower:LOWer:STATe?

Turn channel power lower limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Channel Power—Upper Limit Test

:CALCulate:CHPower:LIMit:CHPower[:UPPer]:STATe OFF|ON|0|1 :CALCulate:CHPower:LIMit:CHPower[:UPPer]:STATe?

Turn channel power upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Channel Power—Lower Limit

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower:LOWer [:DATA] <power>

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower:LOWer [:DATA]?

Set the lower limit, in dBm, for channel power testing. This value should be lower than or equal to the upper limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

2-6 Chapter2

IS-95-A

Page 32

Language Reference

CALCulate Subsystem

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: −50 dBm—All standards

Range: −200 dBm to 50 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use :INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Channel Power—Upper Limit

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower[:UPPer] [:DATA] <power>

:CALCulate:CHPower:LIMit:<standard>:BS|BTS:CHPower[:UPPer] [:DATA]?

Set the upper limit, in dBm, for channel power testing. This value should be higher than or equal to the lower limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A JSTD8 ANSI J-STD-008

IS-95-A

C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell)

Chapter 2 2-7

Page 33

Language Reference

CALCulate Subsystem

PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 50 dBm–All standards

Range: −200 dBm to 50 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use :INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Test Current Results Against all Limits

:CALCulate:CLIMits:FAIL?

Queries the current status of the limit testing. Returns a 0 if the current measurement results pass when compared with the currently set limits for the measurement. Returns a 1 if the current measurement results fail any limit tests.

Spur Close—Limit Deﬁnition Source

:CALCulate:CSPur:LIMit:SOURce STANdard|FILE :CALCulate:CSPur:LIMit:SOURce STANdard|FILE?

Set the source for the limit values used in the limits test.

STANdard Deﬁned by the Standard selected using the

[:SENSe]:RADio:STANdard:BAND command.

FILE Deﬁned by a user entered ﬁle.

Factory Preset and *RST: Standard

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

2-8 Chapter2

Meas Setup, More, Limits…

Page 34

Language Reference

CALCulate Subsystem

Spur Close—Limit Test

:CALCulate:CSPur:LIMit:STATe OFF|ON|0|1 :CALCulate:CSPur:LIMit:STATe?

Turn upper limit test for close-in spurious signals on or off. Factory Preset

and *RST: On Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits & Offsets…

Spurs at Harmonics—Upper Absolute Limit

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:ABSolute [:UPPer][:DATA] <power>

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:ABSolute [:UPPer][:DATA]?

Set the upper absolute limits for harmonics measurement testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: −13 dBm

Range: −200 dBm to 50 dBm

Chapter 2 2-9

Page 35

Language Reference

CALCulate Subsystem

Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access: Meas Setup, Limits …

Spurs at Harmonics—Upper Relative Limit

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:RELative [:UPPer][:DATA] <rel_power>

:CALCulate:HARMonics:LIMit:<standard>:BS|BTS:RELative [:UPPer][:DATA]?

Set the upper relative limit for harmonics measurement testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: −30 dBc

Range: −200 dBc to 50 dBc Default Unit: dB Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

2-10 Chapter2

Meas Setup, More, Limits…

Page 36

Language Reference

CALCulate Subsystem

Spurs at Harmonics—Upper Absolute Limit Test

:CALCulate:HARMonics:LIMit:ABSolute[:UPPer]:STATe OFF|ON|0|1

:CALCulate:HARMonics:LIMit:ABSolute[:UPPer]:STATe?

Turn the harmonics absolute upper limit test on or off. Factory Preset

and *RST: On Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Spurs at Harmonics—Upper Relative Limit Test

:CALCulate:HARMonics:LIMit:RELative[:UPPer]:STATe OFF|ON|0|1

:CALCulate:HARMonics:LIMit:RELative[:UPPer]:STATe?

Turn the harmonics relative upper limit test on or off. Factory Preset

and *RST: On Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Occupied Bandwidth—Emissions Bandwidth Lower Limit

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth:LOWer [:DATA] <frequency>

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth:LOWer [:DATA]?

Set the lower limit for occupied bandwidth measurement emissions bandwidth testing. This value should be less than the upper limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Chapter 2 2-11

Page 37

Language Reference

CALCulate Subsystem

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 1.0 MHz—All standards

Range: 10 Hz to 50 MHz Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, Limits …

Occupied Bandwidth—Emissions Bandwidth Lower Limit Test

:CALCulate:OBWidth:LIMit:EBWidth:LOWer:STATe OFF|ON|0|1 :CALCulate:OBWidth:LIMit:EBWidth:LOWer:STATe?

Turn the emissions bandwidth lower limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

2-12 Chapter2

Page 38

Language Reference

CALCulate Subsystem

Occupied Bandwidth—Emissions Bandwidth Upper Limit

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth[:UPPer] [:DATA] <frequency>

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS:EBWidth[:UPPer] [:DATA]?

Set the upper limit for occupied bandwidth measurement emissions bandwidth testing. This value should be greater than the lower limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 1.5 MHz—All standards

Range: 10 Hz to 50 MHz Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Chapter 2 2-13

Page 39

Language Reference

CALCulate Subsystem

Occupied Bandwidth—Emissions Bandwidth Upper Limit Test

:CALCulate:OBWidth:LIMit:EBWidth[:UPPer]:STATe OFF|ON|0|1 :CALCulate:OBWidth:LIMit:EBWidth[:UPPer]:STATe?

Turn emissions bandwidth upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Occupied Bandwidth—Occupied Bandwidth Lower Limit

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS [:OBWidth]:LOWer[:DATA] <frequency>

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS [:OBWidth]:LOWer[:DATA]?

Set the lower limit for occupied bandwidth measurement testing. This value must be lower than the upper limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS)

IS-95-A

C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

2-14 Chapter2

Page 40

Language Reference

CALCulate Subsystem

Factory Preset and *RST: 1.0 MHz—All standards

Range: 10 Hz to 50 MHz Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Occupied Bandwidth—Occupied Bandwidth Lower Limit Test

:CALCulate:OBWidth:LIMit[:OBWidth]:LOWer:STATe OFF|ON|0|1 :CALCulate:OBWidth:LIMit[:OBWidth]:LOWer:STATe?

Turn occupied bandwidth lower limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Occupied Bandwidth—Occupied Bandwidth Upper Limit

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS [:OBWidth][:UPPer][:DATA] <frequency>

:CALCulate:OBWidth:LIMit:<standard>:BS|BTS [:OBWidth][:UPPer][:DATA]?

Set the upper limit for occupied bandwidth measurement testing. This value must be greater than the lower limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

Chapter 2 2-15

IS-95-A

Page 41

Language Reference

CALCulate Subsystem

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST:

IS95A, C95B, C95C, CKOR, JSTD8, P95B, P95C, PKOR ARIB T53

1.5 MHz 1.48 MHz

Range: 10 Hz to 50 MHz Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Occupied Bandwidth—Occupied Bandwidth Upper Limit Test

:CALCulate:OBWidth:LIMit[:OBWidth][:UPPer]:STATe OFF|ON|0|1 :CALCulate:OBWidth:LIMit[:OBWidth][:UPPer]:STATe?

Turn occupied bandwidth upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

2-16 Chapter2

Meas Setup, More, Limits…

Page 42

Language Reference

CALCulate Subsystem

Out of Band Spurious—Upper Absolute Limit

:CALCulate:OOBSpur:LIMit:TABLe:ABSolute[:UPPer][:DATA] <power1, power2, …, powerN>

:CALCulate:OOBSpur:LIMit:TABLe:ABSolute[:UPPer][:DATA]?

Set the upper absolute limits for each out of band spurious emissions measurement range.

Range: −170 dBm to 170 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, Edit Table …

Out of Band Spurious—Upper Relative Limit

:CALCulate:OOBSpur:LIMit:TABLe:RELative[:UPPer][:DATA] <rel_power1, rel_power2, …, rel_powerN>

:CALCulate:OOBSpur:LIMit:TABLe:RELative[:UPPer][:DATA]?

Set the upper relative limits for each out of band spurious emissions measurement range.

Range: −170 dBc to 170 dBc Default Unit: dBc Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, Edit Table …

Chapter 2 2-17

Page 43

Language Reference

CALCulate Subsystem

Out of Band Spurious—Limit Test

:CALCulate:OOBSpur:LIMit:TABLe:TYPE <value1, value2, …, valueN>

:CALCulate:OOBSpur:LIMit:TABLe:TYPE?

Set the pass fail logic criteria for each range of the out of band spurious measurement. Either the absolute or relative limit test can be turned on, both tests can be turned on together, or both tests can be turned off. If both limit tests are turned on, the pass fail logic can be set so the test is passed if both limit tests are passed or if either test is passed.

Factory Preset and *RST: Off

Range: OFF, ABS, REL, OR, and AND Remarks: The enumerated selection is passed as a list <value1,

value2, …, valueN>. You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, Edit Table

Receive Channel Power—Lower Limit Test

:CALCulate:RCHPower:LIMit:RCHPower:LOWer:STATe OFF|ON|0|1 :CALCulate:RCHPower:LIMit:RCHPower:LOWer:STATe?

Turn the receive channel power lower limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Receive Channel Power—Upper Limit Test

:CALCulate:RCHPower:LIMit:RCHPower[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RCHPower:LIMit:RCHPower[:UPPer]:STATe?

Turn receive channel power upper limit test on or off. Factory Preset

and *RST: Off

2-18 Chapter2

Page 44

Language Reference

CALCulate Subsystem

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Receive Channel Power—Lower Limit

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower :LOWer[:DATA] <value>

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower :LOWer[:DATA]?

Set the lower limit, in dBm, for receive channel power testing. This value should be less than or equal to the upper limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A IS-95-A JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: −50 dBm—All standards

Range: −200 dBm to 50 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use :INSTrument:SELect to set the mode.

Front Panel Access:

Chapter 2 2-19

Meas Setup, More, Limits…

Page 45

Language Reference

CALCulate Subsystem

Receive Channel Power—Upper Limit

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower :UPPer[:DATA] <value>

:CALCulate:RCHPower:LIMit:<standard>:BS|BTS:RCHPower :UPPer[:DATA]?

Set the upper limit, in dBm, for receive channel power testing. This value should be greater than or equal to the lower limit value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 50 dBm—All standards

Range: −200 dBm to 50 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use :INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Carrier Feedthrough Upper Limit Test

:CALCulate:RHO:LIMit:CFTHrough[:UPPer[:STATe OFF|ON|0|1 :CALCulate:RHO:LIMit:CFTHrough[:UPPer[:STATe?

Turn Rho carrier feedthrough upper limit test on or off.

2-20 Chapter2

Page 46

Language Reference

CALCulate Subsystem

Factory Preset and *RST: Off

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Error Vector Magnitude Upper Limit Test

:CALCulate:RHO:LIMit:EVM[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RHO:LIMit:EVM[:UPPer]:STATe?

Turn rho error vector magnitude upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Frequency Error Upper Limit Test

:CALCulate:RHO:LIMit:FERRor[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RHO:LIMit:FERRor[:UPPer]:STATe?

Turn the rho frequency error upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Modulation Magnitude Error Upper Limit Test

:CALCulate:RHO:LIMit:MAGNitude[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RHO:LIMit:MAGNitude[:UPPer]:STATe?

Turn rho modulation magnitude error upper limit test on or off.

Chapter 2 2-21

Page 47

Language Reference

CALCulate Subsystem

Factory Preset and *RST: Off

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Modulation Phase Error Upper Limit Test

:CALCulate:RHO:LIMit:PHASe[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RHO:LIMit:PHASe[:UPPer]:STATe?

Turn rho modulation phase error upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Rho Lower Limit Test

:CALCulate:RHO:LIMit:RHO:LOWer:STATe OFF|ON|0|1 :CALCulate:RHO:LIMit:RHO:LOWer:STATe?

Turn rho results lower limit test on or off. Factory Preset

and *RST: ON Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

2-22 Chapter2

Page 48

Language Reference

CALCulate Subsystem

Rho—Carrier Feedthrough Upper Limit

:CALCulate:RHO:LIMit:<standard>:BS|BTS:CFTHrough:[UPPer[ [:DATA] <rel_power>

:CALCulate:RHO:LIMit:<standard>:BS|BTS:CFTHrough:[UPPer[ [:DATA]?

Set the upper limit, in dB, for rho carrier feedthrough testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: −40 dBm—All standards

Range: −200 dB to 0 dB Default Unit: dB Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Error Vector Magnitude Upper Limit

:CALCulate:RHO:LIMit:<standard>:BS|BTS:EVM[:UPPer][:DATA] <percentage>

:CALCulate:RHO:LIMit:<standard>:BS|BTS:EVM[:UPPer][:DATA]?

Set the upper limit, in percent, for rho error vector magnitude testing.

Chapter 2 2-23

Page 49

Language Reference

CALCulate Subsystem

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 25%—All standards

Range: 0 to 100% Default Unit: % (percent) Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Frequency Error Upper Limit

:CALCulate:RHO:LIMit:<standard>:BS|BTS:FERRor[:UPPer] [:DATA] <frequency>

:CALCulate:RHO:LIMit:<standard>:BS|BTS:FERRor[:UPPer] [:DATA]?

Set the upper limit, in hertz, for rho frequency error testing. The absolute value of the frequency error results are tested against this value.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

2-24 Chapter2

Page 50

Language Reference

CALCulate Subsystem

Factory Preset and *RST:

IS95A, C95B, C95C, CKOR, ARIB T53 JSTD8, P95B, P95C PKOR

43.5 Hz 99.5 Hz 93.5 Hz

Range: −1.0 MHz to 1.0 MHz Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Modulation Magnitude Error Upper Limit

:CALCulate:RHO:LIMit:<standard>:BS|BTS:MAGNitude[:UPPer] [:DATA] <percentage>

:CALCulate:RHO:LIMit:<standard>:BS|BTS:MAGNitude[:UPPer] [:DATA]?

Set the upper limit, in percent, for rho modulation magnitude error testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008

Chapter 2 2-25

Page 51

Language Reference

CALCulate Subsystem

C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 25%

Range: 0 to 100% Default Unit: % (percent) Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Modulation Phase Error Upper Limit

:CALCulate:RHO:LIMit:<standard>:BS|BTS:PHASe[:UPPer] [:DATA] <angle>

:CALCulate:RHO:LIMit:<standard>:BS|BTS:PHASe[:UPPer] [:DATA]?

Set the upper limit, in degrees, for rho modulation phase error testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A JSTD8 ANSI J-STD-008

IS-95-A

C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell

2-26 Chapter2

Page 52

Language Reference

CALCulate Subsystem

P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 20 deg—All standards

Range: 0 to 360 Default Unit: degree Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Rho Lower Limit

:CALCulate:RHO:LIMit:<standard>:BS|BTS:RHO:LOWer[:DATA] <parameter>

:CALCulate:RHO:LIMit:<standard>:BS|BTS:RHO:LOWer[:DATA]?

Set the lower limit for rho results testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 0.912—All standards

Range: 0 to 1.0 Default Unit: None

Chapter 2 2-27

Page 53

Language Reference

CALCulate Subsystem

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Rho—Time Offset Upper Limit

:CALCulate:RHO:LIMit:<standard>:BS|BTS:TOFFset[:UPPer] [:DATA] <time>

:CALCulate:RHO:LIMit:<standard>:BS|BTS:TOFFset[:UPPer] [:DATA]?

Set the upper limit, in microseconds, for rho time offset testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: 10 µs

Range: −26.7 ms to 26.7 ms Default Unit: sec Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

2-28 Chapter2

Meas Setup, More, Limits…

Page 54

Language Reference

CALCulate Subsystem

Rho—Time Offset Upper Limit Test

:CALCulate:RHO:LIMit:TOFFset[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RHO:LIMit:TOFFset[:UPPer]:STATe?

Turn time offset upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Receiver Spurious—Receive Upper Limit

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:RECeive[:UPPer] [:DATA] <power>

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:RECeive[:UPPer] [:DATA]?

Set the upper limit, in dBm, for receiver spurious response receive band testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008 C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Chapter 2 2-29

Page 55

Language Reference

CALCulate Subsystem

Factory Preset and *RST: −80 dBm—All standards

Range: −200 dBm to 50 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Receiver Spurious—Receive Upper Limit Test

:CALCulate:RSPur:LIMit:RECeive[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RSPur:LIMit:RECeive[:UPPer]:STATe?

Turn receiver spurious response receive band upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Receiver Spurious—Transmit Upper Limit

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:TRANsmit[:UPPer] [:DATA] <power>

:CALCulate:RSPur:LIMit:<standard>:BS|BTS:TRANsmit[:UPPer] [:DATA]?

Set the upper limit, in dBm, or receive spurious response transmit band testing.

BS = Base Station BTS = Base Transceiver Station BS = BTS

Available Standards

IS95A

IS-95-A

JSTD8 ANSI J-STD-008

2-30 Chapter2

Page 56

Language Reference

CALCulate Subsystem

C95B TIA/EIA-95-B Cell P95B TIA/EIA-95-B PCS CKOR TTA.KO-06.0003 (Korea Cell) PKOR TTA.KO-06.0013 (Korea PCS) C95C TIA/EIA-95-C Cell P95C TIA/EIA-95-C PCS ARIB T53 ARIB-T53

Factory Preset and *RST: −60 dBm—All standards

Range: −200 dBm to 50 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Receiver Spurious—Transmit Upper Limit Test

:CALCulate:RSPur:LIMit:TRANsmit[:UPPer]:STATe OFF|ON|0|1 :CALCulate:RSPur:LIMit:TRANsmit[:UPPer]:STATe?

Turn receive spurious response transmit band upper limit test on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Limits…

Chapter 2 2-31

Page 57

Language Reference

CONFigure Subsystem

:CONFigure:<measurement>

The CONFigure commands are used with several other commands and are documented in the section on the “MEASure Group of Commands”

on page 39.

2-32 Chapter2

Page 58

Language Reference

DISPlay Subsystem

The DISPlay controls the selection and presentation of textual, graphical, and TRACe information. Within a DISPlay, information may be separated into individual WINDows.

Trace Y-Axis Amplitude Scaling

:DISPlay:WINDow:TRACe:Y[:SCALe]:PDIVision <rel_ampl> :DISPlay:WINDow:TRACe:Y[:SCALe]:PDIVision?

Sets the value for each division of the y-axis on the display when y-axis units are set to amplitude units.

Factory Preset and *RST: 10 dB

Range: 0.1 to 20.0 dB Default Unit: dB Front Panel

Access:

AMPLITUDE Y Scale, Scale/Div

Trace Y-Axis Reference Level

:DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVel <ampl> :DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVel?

Sets the reference level (maximum amplitude value on the display) of the y-axis.

Factory Preset and *RST: 0 dBm

Range: With reference level offset:

−327.6 to 55 dBm

−149.9 to 55 dBm with reference level offset and max mixer level = −10 dBm. In external mixing, the range is

−327.5 to −10 dBm at the mixer.

Default Unit: current active units Front Panel

Access:

Chapter 2 2-33

Amplitude Y Scale, Ref Level

Page 59

Language Reference

FETCh Subsystem

:FETCh:<measurement>[n]?

The FETCh? commands are used with several other commands and are documented in the section on the “MEASure Group of Commands” on

page 39.

2-34 Chapter2

Page 60

Language Reference

INITiate Subsystem

The INITiate subsystem is used to control the initiation of the trigger. Refer to the TRIGger and ABORt subsystems for related commands.

Continuous or Single Measurements

:INITiate:CONTinuous OFF|ON|0|1 :INITiate:CONTinuous?

Selects whether the trigger system is continuously initiated or not. This corresponds to continuous measurement or single measurement operation.

When set to ON, at the completion of each trigger cycle, the trigger system immediately initiates another trigger cycle.

When set to OFF, the trigger system remains in an “idle” state until CONTinuous is set to ON or an INITiate[:IMMediate] command is received. On receiving the INITiate{:IMMediate] command, it will go through a single trigger cycle, and then return to the “idle” state.

Factory Preset: ON *RST: ON (OFF recommended for remote operation) Front Panel

Access: Meas Control, Measure Single Cont

Pause the Measurement

:INITiate:PAUSe

Pauses the current measurement by changing the current measurement state from the “wait for trigger” state to the “paused” state. If the measurement is not in the “wait for trigger” state when the command is issued, the transition will be made the next time that state is entered as part of the trigger cycle. When in the pause state, the spectrum analyzer auto-align process stops. If the analyzer is paused for long a period of time, measurement accuracy may degrade.

Front Panel Access:

Meas Control, Pause

Chapter 2 2-35

Page 61

Language Reference

INITiate Subsystem

Restart the Measurement

:INITiate:RESTart

Restarts the current measurement regardless of its current operating state. It is equivalent to:

INITiate[:IMMediate] (for single measurement mode) ABort (for continuous measurement mode)

Front Panel Access:

Restart

Meas Control, Restart

Resume the Measurement

:INITiate:RESume

Resumes the current measurement by changing the current measurement state from the “paused state” back to the “wait for trigger” state. If the measurement is not in the “paused” state, when the command is issued, an error is reported.

Front Panel Access:

Meas Control, Resume

2-36 Chapter2

Page 62

Language Reference

INSTrument Subsystem

This subsystem includes commands for querying and selecting instrument measurement (personality option) modes.

Select Application by Number

:INSTrument:NSELect <integer> :INSTrument:NSELect?

Select the measurement application by its instrument number. The actual available choices depends upon which applications are installed in the instrument.

1 = SA 3 = GSM 4 = cdmaOne

NOTE If you are using the status bits and the analyzer mode is changed, the

status bits should be read, and any errors resolved, prior to switching modes. Error conditions that exist prior to switching modes cannot be detected using the condition registers after the mode change. This is true unless they recur after the mode change, although transitions of these conditions can be detected using the event registers.

Changing modes resets all SCPI status registers and mask registers to their power-on defaults. Hence, any event or condition register masks must be re-established after a mode change. Also note that the power up status bit is set by any mode change, since that is the default state after power up.

Factory Preset and *RST: Persistent state with factory default of 1

Range: 1 to x, where x depends upon which applications are

installed.

Front Panel Access:

Mode

Chapter 2 2-37

Page 63

Language Reference

INSTrument Subsystem

Select Application

:INSTrument[:SELect] ‘SA’|’CDMA’ (application specific mode)

:INSTrument[:SELect]?

Select the measurement application mode by enumerated choice. The actual available choices depends upon which applications (modes) are installed in the instrument.

Once the instrument mode is selected, only the commands that are valid for that mode can be executed. See the manual for installed options for the mode designator (if any) for that option.

NOTE If you are using the SCPI status registers and the analyzer mode is

changed, the status bits should be read, and any errors resolved, prior to switching modes.Error conditions that exist prior to switching modes cannot be detected using the condition registers after the mode change. This is true unless they recur after the mode change, although transitions of these conditions can be detected using the event registers.

Factory Preset and *RST: Persistent state with factory default of Spectrum

Analyzer

Front Panel Access:

Mode

2-38 Chapter2

Page 64

Language Reference

MEASure Group of Commands

This group includes commands used to make measurements and return results. The different commands can be used to provide ﬁne control of the overall measurement process. Most measurements should be done in single measurement mode, rather than doing the measurement continuously.

Each measurement sets the instrument state that is appropriate for that measurement. Other commands are available for each allow changing settings, view, limits, etc. Refer to:

SENSe:<measurement>, SENSe:CHANnel, SENSe:CORRection, SENSe:FREQuency, SENSe:POWer, SENSe:RADio, SENSe:SNYC CALCulate:<measurement>, CALCulate:CLIMits/DATA DISPlay:<measurement> TRIGger

Mode to

Measure Commands

:MEASure:<measurement>[n]?

This is a fast single-command way to make a measurement using the factory default instrument settings. These are the settings and units that conform to the Standard.

• Stops the current measurement and sets up the instrument for the speciﬁed measurement using the factory defaults

• Initiates the data acquisition for the measurement

• Blocks other SCPI communication, waiting until the measurement is complete before returning results.

• Turns the averaging function on and sets the number of averages to 10 for all measurements.

• After the data is valid it returns the scalar results, or the trace data, for the speciﬁed measurement.

Chapter 2 2-39

Page 65

Language Reference

MEASure Group of Commands

If you need to change some of the measurement parameters from the factory default settings you can set up the measurement with the CONFigure command. Use the commands in the SENSe:<measurement> and CALCulate:<measurement> subsystems to change the settings. Then you can use the READ? command, or the INITiate and FETCh? commands, to initiate the measurement and query the results. See Figure 2-1.

If you need to repeatedly make a given measurement with settings other than the factory defaults, you can use the commands in the SENSe:<measurement> and CALCulate:<measurement> subsystems to set up the measurement. Then use the READ? command or INITiate and FETCh? commands, to initiate the measurement and query results.

Measurement settings persist if you initiate a different measurement and then return to a previous one. Use READ:<measurement>? if you want to use those persistent settings. If you want to go back to the default settings, use MEASure:<measurement>?.

Figure 2-1 Measurement Group of Commands

Conﬁgure Commands

:CONFigure:<measurement>

This command stops the current measurement and sets up the instrument for the speciﬁed measurement using the factory default instrument settings. It does not initiate the taking of measurement data. This command also turns the averaging function on and sets the number of averages to 10 for all measurements.

The CONFigure? query returns the current measurement name.

2-40 Chapter2

Page 66

Language Reference

MEASure Group of Commands

Fetch Commands

:FETCh:<measurement>[n]?

This command puts valid data into the output buffer, but does not initiate data acquisition. Use the INITiate[:IMMediate] command to acquire data before you use the FETCh command. You can only fetch results from the measurement that is currently selected.

Read Commands

:READ:<measurement>[n]?

• Does not preset the measurement to the factory defaults. (The MEASure? and CONFigure? commands reset the parameters to the default values.) It uses the settings from the last measurement.

• Initiates the measurement and puts valid data into the output buffer. If a measurement other than the current one is speciﬁed, the instrument will switch to that measurement before it initiates the measurement and returns results.

• Blocks other SCPI communication, waiting until the measurement is complete before returning the results

If the optional [n] value is not included, or is set to 1, the scalar measurement results will be returned. If the [n] value is set to a value other than 1, the selected trace data results will be returned. See each command for details of what types of scalar results or trace data results are available. The binary data formats should be used when handling large blocks of data since they are smaller and faster then the ASCII format.

Chapter 2 2-41

Page 67

Language Reference

MEASure Group of Commands

Code Domain Measurement

This measures the power for each of the 64 Walsh codes/channels, relative to the total power in the pilot channel. You must be in the cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:CDPower commands for more measurement related commands.

:CONFigure:CDPower :FETCh:CDPower[n]? :READ:CDPower[n]? :MEASure:CDPower[n]?

Front Panel Access: Measure, Code Domain

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1

Returns the following comma-separated scalar results:

1. Time offset is a ﬂoating point number with units of seconds. This is the time delay of the even second clock with respect to the start of the short code PN sequences. Time offset takes into account the setting of the PN offset parameter. For example, with the PN offset to 2 the reported time offset would be the calculated time offset times 64 chip intervals (or 2 Χ 52.0833e−6).

2. Frequency error is a ﬂoating point number (in Hz) of the frequency error in the measured signal. This error is based on the linear best ﬁt of the uncorrected measured phase.

3. Carrier feedthrough is a ﬂoating point number (in dB) of the dc offset, of I and Q, from the origin.

4. Pilot power is a ﬂoating point number with units of dB.It is the relative power of the pilot channel (Walsh code 0) with respect to the carrier power.

5. Paging power is a ﬂoating point number with units of dB. It is the relative power of the paging channel (Walsh code 1) with respect to the carrier power.

Continued on next page

2-42 Chapter2

Page 68

Measurement Results Available

n Results Returned

Language Reference

MEASure Group of Commands

not speciﬁed or n=1

Returns the following comma-separated scalar results:

6. Sync power is a ﬂoating point number with units of dB.It is the relative power of the sync channel (Walsh code 32) with respect to the carrier power.

7. Average trafﬁc power is a ﬂoating point number with units of dB. It is the average relative power of the active trafﬁc channels with respect to the carrier power. Trafﬁc channels are deﬁned as all of the Walsh codes except Walsh 0,1,32. A trafﬁc channel is active if its coding power is greater than the active set threshold parameter which you have selected.

8. Maximum inactive trafﬁc power is a ﬂoating point number with units of dB. It is the maximum relative power of an inactive trafﬁc channel with respect to the carrier power.Trafﬁc channels are deﬁned as all of the Walsh codes except Walsh 0,1,32. A trafﬁc channel is inactive if its coding power is less than the active set threshold parameter which you have selected.

9. Average inactive trafﬁc power is a ﬂoating point number with units of dB.It is the average relative power of the inactive trafﬁc channels with respect to the carrier power. Trafﬁc channels are deﬁned as all of the Walsh codes except Walsh 0,1,32. A trafﬁc channel is inactive if its coding power is less than the active set threshold parameter which you have selected.

10.RHO (estimated) is a ﬂoating point number without units. This is an estimate of Rho based on the input signal as a pilot only signal. It is calculated by estimating the noise ﬂoor for the active code channels using the average of the noise in all of the inactive channels. The measured noise ﬂoor is subtracted from all active channels before they are summed together to get the total signal power. The ratio of total noise power to total power is the Rho (estimated).

2 Power trace - Returns comma-separated ﬂoating point numbers that are the

trace data of the code domain power trace for all 64 Walsh codes. This series of 64 numbers represent the relative power levels (in dB) of all 64 walsh codes, with respect to the carrier power.

3 Timing trace - Returns comma-separated ﬂoating point numbers that are

the trace data of the code domain timing trace for all 64 Walsh codes. This series of 64 numbers represent the relative timing estimations (in seconds) of the codes, relative to the pilot channel. Typical values are on the order of 1ns.

NOTE The default method is to measure the power only.

CONFIG and MEAS reset the method parameter to

Power.If you use this subopcode with the method left as

Power, invalid data will be returned. Set Method to

Timing/Phase for proper results.

Chapter 2 2-43

Page 69

Language Reference

MEASure Group of Commands

Measurement Results Available

n Results Returned

4 Phase trace - Returns comma-separated ﬂoating point numbers that are the

trace data of the code domain phase trace for all 64 Walsh codes. This series of 64 numbers represent the relative phase estimations (in radians) of the codes, relative to the pilot channel. Typical values are on the order of 1 mrad.

NOTE The default method is to measure the power only.

CONFIG and MEAS reset the method parameter to

Power.If you use this subopcode with the method left as

Power, invalid data will be returned. Set Method to

Timing/Phase for proper results.

2-44 Chapter2

Page 70

Language Reference

MEASure Group of Commands

Channel Power Measurement

This measures the total rms power in a speciﬁed integration bandwidth. You must be in the cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:CHPower commands for more measurement related commands.

:CONFigure:CHPower :FETCh:CHPower[n]? :READ:CHPower[n]? :MEASure:CHPower[n]?

Front Panel Access:

Measure, Channel Power

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1 Returns 2 comma-separated scalar results:

1. Channel Power is a ﬂoating point number representing the total channel power in the speciﬁed integration bandwidth.

2. Power Spectral Density is the power (in dBm/Hz) in the speciﬁed integration bandwidth.

Chapter 2 2-45

Page 71

Language Reference

MEASure Group of Commands

Spur Close Measurement

This measures the spurious emissions in the transmit band relative to the channel power in the selected channel. You must be in the cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:CSPur commands for more measurement related commands.

:CONFigure:CSPur :FETCh:CSPur[n]? :READ:CSPur[n]? :MEASure:CSPur[n]?

Front Panel Access:

Measure, Spur Close

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1 Returns 10 comma-separated scalar results. The 10 results represent,

ﬁrst, the channel power and then 3 spur values.The 3 values are composed of the spurious value from each of 3 measurement segments. The measurement segments are Lower, Center, and Upper. For each of the 3 spurs displayed, 3 values are returned:

1. The spur frequency difference from channel center frequency (in Hz)

2. The spur amplitude difference from the limit (in dB)

3. The spur amplitude difference from channel power (in dBc)

2 Returns trace of the segment containing the worst spur.

2-46 Chapter2

Page 72

Language Reference

MEASure Group of Commands

Monitor Band/Channel Measurement

This measurement has two measurement methods: monitor band and monitor channel. In monitor band, the cdmaOne frequency band is viewed. In monitor channel, the spectrum of a selected channel is viewed.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:PSTeps commands for more measurement related commands.

:CONFigure:MONitor :FETCh:MONitor[n] :READ:MONitor[n] :MEASure:MONitor[n]

Front Panel Access: Measure, Monitor Band/Channel

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1

No return value

Chapter 2 2-47

Page 73

Language Reference

MEASure Group of Commands

Occupied Bandwidth Measurement

This measures the bandwidth of the carrier signal. You must be in the cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:OBW commands for more measurement related commands.

:CONFigure:OBW :FETCh:OBW[n]? :READ:OBW[n]? :MEASure:OBW[n]?

Front Panel Access:

Measure, Occupied BW

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement results available

n Results Returned

not speciﬁed or n=1 Returns 3 comma-separated scalar results, in the following order:

1. Occupied bandwidth - Hz

2. Emissions bandwidth- Hz

3. Transmit frequency error - Hz

2-48 Chapter2

Page 74

Language Reference

MEASure Group of Commands

Out of Band Spurious Emissions Measurement

This measures the out of band spurious emissions relative to the receive channel power in the selected channel. You must be in the GSM or cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:OOBSpur commands for more measurement related commands.

:CONFigure:OOBSpur :FETCh:OOBSpur[n]? :READ:OOBSpur[n]? :MEASure:OOBSpur[n]?

Front Panel Access:. Measure, Out Of Band Spurious

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1 Returns the following two components:

First—the number of ranges that were measured (1 - 20) Second—the results for each range are returned. Each result is made up of

seven values for each of a maximum of 10 spurs for a total of 10 Χ N spurs and 70 Χ N return values. Where N = the number of ranges set. The return values for each spur are:

1. Range number

2. Spur number

3. Center frequency

4. Amplitude

5. Delta absolute limit

6. Delta relative limit

7. Pass/Fail results

Chapter 2 2-49

Page 75

Language Reference

MEASure Group of Commands

Receive Channel Power Measurement

This measures the total rms power in a speciﬁc bandwidth at the receive channel frequency. You must be in the cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:CHPower commands for more measurement related commands.

:CONFigure:RCHPower :FETCh:RCHPower[n]? :READ:RCHPower[n]? :MEASure:RCHPower[n]?

Front Panel Access:.

Measure, Rx Channel Power

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1 Returns 2 comma-separated scalar results:

1. Channel Power is a ﬂoating point number representing the total channel power in the speciﬁed integration bandwidth.

2. Power Spectral Density is the power (in dBm/Hz) in the speciﬁed integration bandwidth.

2-50 Chapter2

Page 76

Language Reference

MEASure Group of Commands

Rho (Waveform Quality) Measurement

This measures the modulation accuracy of the transmitter by checking the magnitude and phase error and the EVM (error vector magnitude). You must be in the cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:RHO commands for more measurement related commands.

:CONFigure:RHO :FETCh:RHO[n]? :READ:RHO[n]? :MEASure:RHO[n]?

Front Panel Access: Measure, Mod Accuracy (Rho)

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

0 Returns processed I/Q trace data, as a series of comma-separated trace

points. The I values are listed ﬁrst in each pair, using the 0 through even-indexed values. The Q values are the odd-indexed values.

The standard sample rate is 4.9152 MHz and the trace length is determined by the current measurement interval.

The number of trace points depends on the current measurement interval and points per chip settings.

The numbers are sent in the following order:

In-phase (I) sample, of symbol 0 decision point Quadrature-phase (Q) sample, of symbol 0 decision point

...

In-phase (I) sample, of symbol 1 decision point Quadrature-phase (Q) sample, of symbol 1 decision point

...

The trace can be interpolated to 1, 2, 4 points/chip selected with the display Points/Chip softkey or the NSPC remote command.

The Points/Chip soft key controls number of points between decision points in the trace, changing the number of I/Q pairs sent for each decision point.

1=only the decision points 2=the decision points with one point between them 4=the decision points with three points between them

Chapter 2 2-51

Page 77

Language Reference

MEASure Group of Commands

n Results Returned

not speciﬁed or n=1 Returns 7 comma-separated ﬂoating point numbers, in the following order:

1. Rho (no units) represents the correlation of the measured power compared to the ideal pilot channel. The calculation is performed after the complimentary ﬁlter, so it is IS95 compliant. It is performed at the decision points in the pilot waveform. If averaging is on, this is the average of the individual rms measurements.

2. Time offset (with units of seconds) is the time delay of the even second clock with respect to the start of the short code PN sequences, at offsets from the 15 zeros in the characteristic phase of the sequence.

3. Frequency error of the measured signal, with units of Hz. This is based on the linear best ﬁt of the uncorrected measured phase.

4. Carrier feedthrough has units of dB and is the dc error offset of I and Q, from the origin.

5. EVM has units of percent. The calculation is based on the composite of the phase error and magnitude error, between the measured signal and the ideal pilot channel. It is performed after the complimentary ﬁlter which removes the inter-symbol interference in the modulated data. If averaging is on, this is the average of the individual rms measurements.

6. Magnitude error (with units of percent) is the rms error between the measured (compensated) magnitude and the ideal magnitude. This is performed after the complimentary ﬁlter which removes the inter-symbolinterference in the modulated data. If averaging is on, this is the average of the individual rms measurements.

7. Phase error (with units in percent) is the rms phase error between the measured phase and the ideal phase. The calculation is performed after the complimentary ﬁlter which removes the inter-symbol interference in the modulated data. If averaging is on, this is the average of the individual rms measurements.

2 EVM Trace − returns error vector magnitude (EVM) data, as

comma-separated trace points in percent. The ﬁrst value is the chip 0 decision point. The trace is interpolated for the currently selected points/chips displayed on the front panel. The number of trace points depends on the current measurement interval setting.

3 Magnitude Error Trace − returns magnitude error data, as

comma-separated trace points, in percent. The ﬁrst value is the chip 0 decision point. The trace is interpolated for the currently selected points/chips displayed on the front panel. The number of trace points depends on the current measurement interval setting.

4 Phase Error Trace − returns phase error data as comma-separated trace

points, in degrees. The ﬁrst value is the chip 0 decision point. The trace is interpolated for the currently selected points/chip displayed on the front panel. The number of trace points depends on the current measurement interval setting.

2-52 Chapter2

Page 78

Language Reference

MEASure Group of Commands

n Results Returned

6 Reference IQ Data − returns a series of ﬂoating point numbers that

alternately represent I and Q pairs of the reference trace data. The number of trace points depends on the current measurement interval

and points per chip settings. The numbers are sent in the following order:

In-phase (I) sample, of symbol 0 decision point Quadrature-phase (Q) sample, of symbol 0 decision point

...

In-phase (I) sample, of symbol 1 decision point Quadrature-phase (Q) sample, of symbol 1 decision point

...

The trace can be interpolated to 1, 2, 4 points/chip selected with the display Points/Chip softkey or the NSPC remote command.

The Points/Chip soft key controls number of points between decision points in the trace, changing the number of I/Q pairs sent for each decision point.

1=only the decision points 2=the decision points with one point between them 4=the decision points with three points between them

Chapter 2 2-53

Page 79

Language Reference

MEASure Group of Commands

Receiver Spurious Response Measurement

This measures the spurious emissions in the receive band relative to the channel power in the selected channel. You must be in the cdmaOne mode to use these commands. Use INSTrument:SELect to set the mode.

The general functionality of CONFigure, FETCh, MEASure, and READ are described at the beginning of this section. See the SENSe:RSPur commands for more measurement related commands.

:CONFigure:RSPur :FETCh:RSPur[n]? :READ:RSPur[n]? :MEASure:RSPur[n]?

Front Panel Access:.

Measure, RX Spur

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1 Returns 9 comma-separated scalar results corresponding to the 3 worst

spurs in the band starting with the worst:

1. The worst spur’s frequency (in Hz)

2. The worst spur’s amplitude (in dBm)

3. The worst spur’s amplitude difference from the limit (in dB)

4. The second worst spur’s frequency (in MHz)

5. The second worst spur’s amplitude (in dBm)

6. The second worst spur’s amplitude difference from the limit (in dB)

7. The third worst spur’s frequency (in Hz)

8. The third worst spur’s amplitude (in dBm)

9. The third worst spur’s amplitude difference from the limit (in dB)

If no second or third spurs are found, a value of 999 is returned.

2-54 Chapter2

Page 80

Language Reference

MEASure Group of Commands

Spurs at Harmonics Measurement

Measures the power of the spurious emissions at the selected harmonic frequencies of the current channel frequency using the selected resolution bandwidth ﬁlter. You can set the number of spurs to be measured. For each harmonic, the reference level is set 40 dB above the largest amplitude limit with input attenuation held constant. The attenuation is set to limit the carrier (fundamental) power at the spectrum analyzer input mixer to the value determined by

Max Mixer Lvl. You must be in the cdmaOne mode to use these

commands. Use INSTrument:SELect to set the mode. The general functionality of CONFigure, FETCh, MEASure, and READ

are described at the beginning of this section. See the SENSe:HARMonics commands for more measurement related commands.

:CONFigure:HARMonics :FETCh:HARMonics[n]? :READ:HARMonics[n]? :MEASure:HARMonics[n]?

Front Panel Access:

Measure, Harmonics

After the measurement is selected, press Restore Meas

Defaults to restore factory defaults.

Measurement Results Available

n Results Returned

not speciﬁed or n=1 Returns 61 values. The channel power value and a 10 row by 6 column

array of values. Each row contains the following values:

1. Harmonic number

2. Frequency (MHz)

3. Absolute amplitude (dBm)

4. Delta from the absolute limit

5. Relative amplitude from the carrier (dBc)

6. Delta from the relative limit

Chapter 2 2-55

Page 81

Language Reference

MMEMory Subsystem

The purpose of the MMEMory subsystem is to provide access to mass storage devices such as internal or external disk drives. Any part of memory that is treated as a device will be in the MMEMory subsystem.

If mass storage is not speciﬁed in the ﬁlename, the default mass storage speciﬁed in the MSIS command will be used.

The forward slash / and the reverse slash \ are both acceptable delimiters for specifying a directory path.

Store a Measurement Results in a File

:MMEMory:STORe:RESults filename.csv

Saves the measurement results to a ﬁle in memory. The ﬁle name must have a ﬁle extension of .csv and will be in the CSV (comma-separated values) format.

Example: MMEM:STOR:RES ‘C:mymeas.csv’ Front Panel

Access: File, Save, Type, More, Measurement Results

2-56 Chapter2

Page 82

Language Reference

READ Subsystem

:READ:<measurement>[n]?

The READ? commands are used with several other commands and are documented in the section on the “MEASure Group of Commands” on

page 39.

Chapter 2 2-57

Page 83

Language Reference

SENSe Subsystem

Sets the instrument state parameters so that you can measure the input signal.

Code Domain Measurement

Commands for querying the code domain measurement results and for setting to the default values are found in the “MEASure Group of

Commands” on page 39. The equivalent front panel keys for the

parameters described in the following commands, are found under the

Meas Setup key, after the Code Domain measurement has been selected

from the

Code Domain—Average Count

[:SENSe]:CDPower:AVERage:COUNt <integer> [:SENSe]:CDPower:AVERage:COUNt?

MEASURE key menu.

Set the number of frames that will be averaged. After the speciﬁed number of frames (average counts) have been averaged, the averaging mode (termination control) setting determines the averaging action.

Factory Preset and *RST: 10

Range: 1 to 1000 Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Code Domain—Averaging State

[:SENSe]:CDPower:AVERage[:STATe] OFF|ON|0|1 [:SENSe]:CDPower:AVERage[:STATe]?

Turn code domain averaging on or off. Factory Preset

and *RST: Off Remarks: Trace data results are not averaged. Only scalar results

are averaged. You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

2-58 Chapter2

Page 84

Language Reference

SENSe Subsystem

Code Domain—Averaging Termination Control

[:SENSe]:CDPower:AVERage:TCONtrol EXPonential|REPeat [:SENSe]:CDPower:AVERage:TCONtrol?

Select the type of termination control used for averaging. This determines the averaging action after the speciﬁed number of frames (average count) is reached.

Exponential - Each successive data acquisition after the average count is reached, is exponentially weighted and combined with the existing average.

Repeat - After reaching the average count, the averaging is reset and a new average is started.

Factory Preset and *RST: Exponential

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Code Domain—Active Set Threshold

[:SENSe]:CDPower:ASET:THReshold <rel_power> [:SENSe]:CDPower:ASET:THReshold?

Set the active set threshold value. Walsh channels with power less than this value, will be treated as non-active (noise) channels.

Factory Preset and *RST: −20 dB

Range: −200 dB to 0 dB Default Unit: dB Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Code Domain—RF Mixer Input Maximum Power

[:SENSe]:CDPower:MIXer:RANGe[:UPPer] <power> [:SENSe]:CDPower:MIXer:RANGe[:UPPer]?

Speciﬁes the maximum power at the input mixer for the code domain measurement.

Factory Preset and *RST: −10 dBm

Range: −70 dBm to 30 dBm

Chapter 2 2-59

Page 85

Language Reference

SENSe Subsystem

Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use :INSTrument:SELect to set the mode.

Front Panel Access: Meas Setup, Advanced, Max Mixer Lvl

Code Domain—Method

[:SENSe]:CDPower:METHod POWer|TPHase [:SENSe]:CDPower:METHod?

Select the measurement method.

• Power - Measures the code domain power of all 64 Walsh Channels.

• Timing & Phase - Measures the code domain power, code domain timing, and code domain phase of all 64 Walsh channels.

Factory Preset and *RST: Power

Remarks You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Code Domain—Spectrum Normal/Invert

[:SENSe]:CDPower:SPECtrum NORMal|INVert [:SENSe]:CDPower:SPECtrum?

Select normal or inverted spectrum for demodulation.

Normal - normal spectrum is used. Invert - speciﬁes phase inversion where the sign of ‘Q’ is reversed.

Factory Preset and *RST: Normal

Remarks You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

2-60 Chapter2

Page 86

Language Reference

SENSe Subsystem

Code Domain (Measurement Interval)

[:SENSe]:CDPower:SWEep:TIME <time> [:SENSe]:CDPower:SWEep:TIME?

Set the length of the measurement interval that will be used. Factory Preset

and *RST: 1.250 ms Range: 500 µs to 26.7 ms Default Unit: seconds Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Chapter 2 2-61

Page 87

Language Reference

SENSe Subsystem

Digital Demod PN Offset

[:SENSe]:CHANnel:PNOFfset <integer> [:SENSe]:CHANnel:PNOFfset?

Set the PN offset number for the base station being tested. Factory Preset

and *RST: 0 Range: 0 to 511 Default Unit: None Remarks: Global to the current mode.

You must be in the cdmaOne mode to use this command. Use INSTrument:SELect to set the mode.

Front Panel Access:

FREQUENCY Channel, PN Offset

Mode Setup, Demod, Tab⇒

RF Channel Frequency

[:SENSe]:CHANnel:RFCHannel:FREQuency <freq> [:SENSe]:CHANnel:RFCHannel:FREQuency?

Set the RF channel frequency. Factory Preset

and *RST: The ﬁrst channel in the current tuning plan. Range: The same as the SA Range Default Unit: Hz Remarks: Global to the current mode.

To use this command, select the appropriate mode using INSTrument:SELect.

Front Panel Access:

FREQUENCY Channel, Channel Freq

2-62 Chapter2

Page 88

Language Reference

SENSe Subsystem

RF Channel Number

[:SENSe]:CHANnel:RFCHannel[:NUMBer] <integer> [:SENSe]:CHANnel:RFCHannel[:NUMBer]?

Set the analyzer to a frequency that corresponds to the RF channel number.

Factory Preset and *RST: 1

Range: IS-95A—1 to 799 and 991 to 1023

J-STD-008—1 to 1199 ARIB STD-T53—1 to 799, 801-1039, 1041-1199

TTA.KO-06.0003 (Korea Cell)—1 to 799 and 991 to 1023 TTA.KO-06.0013 (Korea PCS)—1 to 599

Default Unit: None Remarks: Global to the current mode.

You must be in the cdmaOne mode to use this command. Use INSTrument:SELect to set the mode.

Front Panel Access:

FREQUENCY Channel, RF Channel

Chapter 2 2-63

Page 89

Language Reference

SENSe Subsystem

Channel Power Measurement

Commands for querying the channel power measurement results and for setting to the default values are found in the “MEASure Group of

Commands” on page 39. The equivalent front panel keys for the

parameters described in the following commands, are found under the

Meas Setup key, after the Channel Power measurement has been selected

from the

Channel Power—Average Count

[:SENSe]:CHPower:AVERage:COUNt <integer> [:SENSe]:CHPower:AVERage:COUNt?

Set the number of data acquisitions that will be averaged. After the speciﬁed number of average counts, the averaging mode (terminal control) setting determines the averaging action.

Factory Preset and *RST: 10

MEASURE key menu.

Range: 1 to 1000 Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup

Channel Power—Averaging State

[:SENSe]:CHPower:AVERage[:STATe] OFF|ON|0|1 [:SENSe]:CHPower:AVERage[:STATe]?

Turn averaging on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup

2-64 Chapter2

Page 90

Language Reference

SENSe Subsystem

Channel Power—Averaging Termination Control

[:SENSe]:CHPower:AVERage:TCONtrol EXPonential|REPeat [:SENSe]:CHPower:AVERage:TCONtrol?

Select the type of termination control used for the averaging function. This determines the averaging action after the speciﬁed number of data acquisitions (average count) is reached.

Exponential - Each successive data acquisition after the average count is reached, is exponentially weighted and combined with the existing average.

Repeat - After reaching the average count, the averaging is reset and a new average is started.

Factory Preset and *RST: Repeat

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup

Channel Power—Integration BW

[:SENSe]:CHPower:BANDwidth|BWIDth:INTegration <freq> [:SENSe]:CHPower:BANDwidth|BWIDth:INTegration?

Set the Integration BW (IBW) that will be used. Factory Preset

and *RST: Channel bandwidth of the standard selected using the

[:SENSe]:RADio:STANdard:BAND command. Range: 1 kHz to ESA span maximum Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Front Panel

Access:

Meas Setup

Chapter 2 2-65

Page 91

Language Reference

SENSe Subsystem

Channel Power—Resolution Bandwidth

[:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution] <freq> [:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution]?

Set the resolution bandwidth that will be used. If span is set to a value greater than 5 MHz, minimum resolution bandwidth is limited to 1 kHz.

Factory Preset and *RST: 10 kHz

Range: Option 1DR—10 Hz to 5 MHz

non- Option 1DR—1 kHz to 5 MHz Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Front Panel

Access:

Meas Setup, More, Advanced, Resolution BW

Channel Power—Resolution Bandwidth State

[:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution]:AUTO OFF|ON|0|1

[:SENSe]:CHPower:BANDwidth|BWIDth[:RESolution]:AUTO?

Select auto (default value) or manual (user entered value) to set the resolution bandwidth.

Factory Preset and *RST: On

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Front Panel

Access:

Meas Setup, Advanced, Resolution BW

Channel Power—Span

[:SENSe]:CHPower:FREQuency:SPAN <freq> [:SENSe]:CHPower:FREQuency:SPAN?

Set the frequency span that will be used. If resolution bandwidth is set to a value less than 1 kHz, maximum span is limited to 5 MHz.

2-66 Chapter2

Page 92

Language Reference

SENSe Subsystem

Factory Preset and *RST: Coupled (to the integration BW at approximately 1.6

times the integration bandwidth)

Range: IBW to IBW

Χ 400

Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup

Channel Power—Noise Correction State

[:SENSe]:CHPower:CORRection:NOISe[:AUTO] OFF|ON|0|1 [:SENSe]:CHPower:CORRection:NOISe[:AUTO]?

Turn Noise Correction to off or auto. When set to auto, noise correction will be activated when the measurement is within less than the noise correction threshold from the computed SA noise ﬂoor. Noise correction Threshold may be set using the Properties Form under the Mode Setup and Properties… keys.

Factory Preset and *RST: Off

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access: Meas Setup

Channel Power—Maximum Mixer Power

[:SENSe]:CHPower:MIXer:RANGe[:UPPer] <power> [:SENSe]:CHPower:MIXer:RANGe[:UPPer]?

Speciﬁes the maximum power at the input mixer for the channel power measurement.

Factory Preset and *RST: −10 dBm

Range: –70 dBm to 10 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use :INSTrument:SELect to set the mode.

Chapter 2 2-67

Page 93

Language Reference

SENSe Subsystem

Front Panel Access:

Meas Setup, Advanced, Max Mixer Lvl

Channel Power—Trigger Source

[:SENSe]:CHPower:TRIGger:SOURce EXTernal|IMMediate [:SENSe]:CHPower:TRIGger:SOURce?

Select the trigger source used to control the data acquisitions. This is an Advanced control that normally does not need to be changed.

External - rear panel external trigger input Immediate - the next data acquisition is immediately taken (also

called Free Run).

Factory Preset and *RST: Immediate (Free Run)

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Front Panel

Access:

Meas Setup, Advanced, Trig Source

2-68 Chapter2

Page 94

Language Reference

SENSe Subsystem

Correction for Base Station RF Port External Attenuation

[:SENSe]:CORRection:BS[:RF]:LOSS <rel_power> [:SENSe]:CORRection:BS[:RF]:LOSS?

Set the correction equal to the external attenuation used when measuring base stations.

Factory Preset and *RST: 0 dB

Range: –50 to 100 dB Default Unit: dB Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Value is used by all measurements except Rx Spur and

Rx Channel Power.

Front Panel Access:

Input

Mode Setup, Input, Tab⇒

RF Noise Correction Threshold

[:SENSe]:CORRection:NOISe:THReshold <rel_power> [:SENSe]:CORRection:NOISe:THReshold?

Sets the signal level above the noise ﬂoor at which the noise correction factor is automatically applied.

Factory Preset and *RST: 15 dB

Range: 0 dB to 100 dB Default Unit: dB Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Chapter 2 2-69

Mode Setup, Properties

Page 95

Language Reference

SENSe Subsystem

RF Gain Correction [:SENSe]:CORRection[:RF]:GAIN

<rel_power> [:SENSe]:CORRection[:RF]:GAIN?

Sets the gain of the external preampliﬁer for mobile station measurements.

Factory Preset and *RST: 0 dB

Range: 0 dB to 100 dB Default Unit: dB Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Value is used the Rx Spur and Rx Channel Power

measurements. Front Panel

Access:

Input, Tab⇒

Mode Setup, Input, Tab⇒

2-70 Chapter2

Page 96

Language Reference

SENSe Subsystem

Spur Close—Measurement

Commands for querying the close spurs measurement results and for setting to the default values are found in the “MEASure Group of

Commands” on page 39. The equivalent front panel keys for the

parameters described in the following commands, are found under the

Meas Setup key, after the Spur Close measurement has been selected

from the

MEASURE key menu.

Spur Close—Average Count

[:SENSe]:CSPur:AVERage:COUNt <integer> [:SENSe]:CSPur:AVERage:COUNt?

Set the number of data acquisitions that will be averaged. After the speciﬁed number of average counts, the averaging mode (terminal control) setting determines the averaging action.

Factory Preset and *RST: 10

Range: 1 to 1,000 Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup

Spur Close—Averaging State

[:SENSe]:CSPur:AVERage[:STATe] OFF|ON|0|1 [:SENSe]:CSPur:AVERage[:STATe]?

Turn averaging on or off. Factory Preset

and *RST: Off Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup

Chapter 2 2-71

Page 97

Language Reference

SENSe Subsystem

Spur Close—Averaging Termination Control

[:SENSe]:CSPur:AVERage:TCONtrol EXPonential|REPeat [:SENSe]:CSPur:AVERage:TCONtrol?

Select the type of termination control used for the averaging function. This determines the averaging action after the speciﬁed number of data acquisitions (average count) is reached.

Exponential - Each successive data acquisition after the average count is reached, is exponentially weighted and combined with the existing average.

Repeat - After reaching the average count, the averaging is reset and a new average is started.

Factory Preset and *RST: Repeat

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Front Panel

Access:

Meas Setup

Spur Close—Type

[:SENSe]:CSPur:TYPE EXAMine|FULL [:SENSe]:CSPur:TYPE?

Select the measurement type. Examine In single sweep mode—measures spurs in the upper,

lower, and center segments and then displays the

segment with the highest power spur. You can select

other segments for display using the

In the continuous mode—measures spurs in the upper,

lower, and center segment. It then continuously

measures the segment with the highest power spur. You

can select other segments for display using the

key. The initial spur values are held and the marker

value is updated with the current spur value found on

each sweep.

measurement type

Segment All is not active when the

Examine is selected.

View key.

View

Full In single sweep mode—measures the spurs in the

upper, lower, and center segments and then displays

the segment with the highest power spur. You can

select other segments for display using the

2-72 Chapter2

View key.

Page 98

Language Reference

SENSe Subsystem

In continuous mode—measures spurs in the upper, lower, and center segment. It then continuously cycles through segments. Unlike

Examine, all results values

are updated with the current spur values found on each sweep.

Factory Preset and *RST: Full

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, Meas Setup

Spur Close—Resolution Bandwidth

[:SENSe]:CSPur:BANDwidth|BWIDth[:RESolution] <freq> [:SENSe]:CSPur:BANDwidth|BWIDth[:RESolution]?

Set the resolution bandwidth that will be used. If span is set to a value greater than 5 MHz, minimum resolution bandwidth is limited to 1 kHz.

Factory Preset and *RST: 30 kHz

Range: Option 1DR—10 Hz to 5 MHz

non- Option 1DR—1 kHz to 5 MHz Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Front Panel

Access:

Meas Setup, More, Advanced, Resolution BW

Spur Close—Video Bandwidth

[:SENSe]:CSPur:BANDwidth|BWIDth:VIDeo <freq> [:SENSe]:CSPur:BANDwidth|BWIDth:VIDeo?

Set the video bandwidth that will be used. Factory Preset

and *RST: 3 kHz Range: Option 1DR—30 Hz to 3 MHz

non- Option 1DR—1 kHz to 3 MHz

Chapter 2 2-73

Page 99

Language Reference

SENSe Subsystem

Default Unit: Hz Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access: Meas Setup, More, Advanced, Video BW

Spur Close—Detector Mode

[:SENSe]:CSPur:DETector[:FUNCtion] POSitive|NEGative|SAMPle [:SENSe]:CSPur:DETector[:FUNCtion]?

Set the detector mode type for the measurement. Factory Preset

and *RST: Sample Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Advanced, Detector

Spur Close—RF Mixer Input Maximum Power

[:SENSe]:CSPur:MIXer:RANGe[:UPPer] <power> [:SENSe]:CSPur:MIXer:RANGe[:UPPer]?

Speciﬁes the maximum power at the input mixer for the measurement. Factory Preset

and *RST: −10 dBm Range: −70 dBm to 10 dBm Default Unit: dBm Remarks: You must be in the cdmaOne mode to use this

command. Use :INSTrument:SELect to set the mode.

Front Panel Access:

Meas Setup, More, Advanced, Max Mixer Lvl

2-74 Chapter2

Page 100

Language Reference

SENSe Subsystem

Spur Close—Trigger Source

[:SENSe]:CSPur:TRIGger:SOURce EXTernal|IMMediate [:SENSe]:CSPur:TRIGger:SOURce?

Select the trigger source used to control the data acquisitions.

External – rear panel external trigger input. Immediate – the next data acquisition is immediately taken,

capturing the signal asynchronously (also called free run).

Factory Preset and *RST: Immediate

Remarks: You must be in the cdmaOne mode to use this

command. Use INSTrument:SELect to set the mode. Front Panel

Access:

Meas Setup, More, Advanced, Trig Source

Chapter 2 2-75

Agilent E4402B Programming Commands

Specifications and Main Features

Frequently Asked Questions

User Manual

Functional Index to SCPI Subsection

2 Language Reference

CALCulate Subsystem

Code Domain—Estimated Rho Lower Limit Testing

Code Domain—Relative Phase Upper Limit Testing

Code Domain—Estimated Rho Lower Limit

Code Domain—Relative Phase Upper Limit

Code Domain—Relative Timing Upper Limit

Code Domain—Relative Timing Upper Limit Testing

Channel Power—Lower Limit Test

Channel Power—Upper Limit Test

Channel Power—Lower Limit

Channel Power—Upper Limit

Test Current Results Against all Limits

Spur Close—Limit Test

Spurs at Harmonics—Upper Absolute Limit

Spurs at Harmonics—Upper Relative Limit

Spurs at Harmonics—Upper Absolute Limit Test

Spurs at Harmonics—Upper Relative Limit Test

Occupied Bandwidth—Emissions Bandwidth Lower Limit

Occupied Bandwidth—Emissions Bandwidth Lower Limit Test

Occupied Bandwidth—Emissions Bandwidth Upper Limit

Occupied Bandwidth—Emissions Bandwidth Upper Limit Test

Occupied Bandwidth—Occupied Bandwidth Lower Limit

Occupied Bandwidth—Occupied Bandwidth Lower Limit Test

Occupied Bandwidth—Occupied Bandwidth Upper Limit

Occupied Bandwidth—Occupied Bandwidth Upper Limit Test

Out of Band Spurious—Upper Absolute Limit

Out of Band Spurious—Upper Relative Limit

Out of Band Spurious—Limit Test

Receive Channel Power—Lower Limit Test

Receive Channel Power—Upper Limit Test

Receive Channel Power—Lower Limit

Receive Channel Power—Upper Limit

Rho—Carrier Feedthrough Upper Limit Test

Rho—Error Vector Magnitude Upper Limit Test

Rho—Frequency Error Upper Limit Test

Rho—Modulation Magnitude Error Upper Limit Test

Rho—Modulation Phase Error Upper Limit Test

Rho—Rho Lower Limit Test

Rho—Carrier Feedthrough Upper Limit

Rho—Error Vector Magnitude Upper Limit

Rho—Frequency Error Upper Limit

Rho—Modulation Magnitude Error Upper Limit

Rho—Modulation Phase Error Upper Limit

Rho—Rho Lower Limit

Rho—Time Offset Upper Limit

Rho—Time Offset Upper Limit Test

Receiver Spurious—Receive Upper Limit

Receiver Spurious—Receive Upper Limit Test

Receiver Spurious—Transmit Upper Limit

Receiver Spurious—Transmit Upper Limit Test

CONFigure Subsystem

DISPlay Subsystem

Trace Y-Axis Amplitude Scaling

Trace Y-Axis Reference Level

FETCh Subsystem

INITiate Subsystem

Continuous or Single Measurements

Pause the Measurement

Restart the Measurement

Resume the Measurement

INSTrument Subsystem

Select Application by Number

Select Application

MEASure Group of Commands

Measure Commands

Fetch Commands

Read Commands

Code Domain Measurement

Channel Power Measurement

Spur Close Measurement

Monitor Band/Channel Measurement

Occupied Bandwidth Measurement

Out of Band Spurious Emissions Measurement

Receive Channel Power Measurement