Network Analyzer Accessories
Overview
Accessories for the HP 8753D, 8720D, and the
8510C series network analyzers include a variety
of calibration kits, verification kits, cables, and
adapters from dc to 110 GHz.
Calibration Kits
Error-correction procedures require that the
systematic errors in the measurement system be
characterized by measuring known devices (standards) on the system over the frequency range of
interest. HP offers two types of calibration kits:
mechanical and electronic.
Electronic Calibration (ECal) Kits
ECal kits consist of connector specific modules,
adapters for test ports and a torque wrench for
proper connection.
75
Mechanical Calibration Kits
All network analyzer mechanical calibration kits
contain precision standard devices to characterize
the systematic errors of the HP 8753 series,
8720 series or 8510C network analyzer system.
Each mechanical calibration kit also contains
adapters for test ports and a torque wrench for
proper connection.
Verification Kits
Measuring known devices, other than the calibration standards, is a straightforward way of verifying
that the network analyzer system is operating
properly. HP offers verification kits that include
precision airlines, mismatch airlines, and precision
fixed attenuators. Traceable measurement data is
shipped with each kit on disk. Verification kits may
be recertified by Hewlett-Packard. This recertification
includes a new measurement of all standards and
new data with uncertainties.
11
76
Network Analyzer Accessories
Electronic Calibration Kits
1
Frequency
HP Model Connector Range (GHz) Description
85060A 7 mm 1 to 18 One two-port ECal
module and collet
remover
Option 001 7 mm 0.045 to 2 Adds lowband
ECal module
85062A 3.5 mm (m-f) 1 to 26.5 One two-por t
ECal module and
m-m and f-f adapters
Option 001 3.5 mm (m-f) 0.045 to 2 Adds lowband
ECal module
Option 00F 3.5 mm (f-f) Changes
connectors to f-f
Option 00M 3.5 mm (m-m) Changes
connectors to m-m
85064A Type-N (m-f) 1 to 18 One two-port
ECal module
Option 001 Type-N (m-f) 0.045 to 2 Adds lowband
ECal module
Option 00F Type-N (f-f) Changes
connectors to f-f
Option 00M Type-N (m-m) Changes
connectors to m-m
1
Must have an HP 85060C control unit to perform electronic calibration.
Mechanical Calibration Kits
2,3,4,5
Frequency
HP Model Connector Range (GHz) Type
85036B Type-N (75 Ω) DC to 6 Economy
85039A Type-F (75 Ω) DC to 3 Economy
85031B 7 mm DC to 6 Economy
85050B 7 mm 0.045 to 18 Standard
85050C 7 mm 0.045 to 18 Precision
85050D 7 mm 0.045 to 18 Economy
85033D 3.5 mm DC to 6 Economy
85052B 3.5 mm 0.045 to 26.5 Standard
85052C 3.5 mm 0.045 to 26.5 Precision
85052D 3.5 mm 0.045 to 26.5 Economy
85032B Type-N DC to 6 Economy
85054B Type-N 0.045 to 18 Standard
85054D Type-N 0.045 to 18 Economy
85056A 2.4 mm 0.045 to 50 Standard
85056D 2.4 mm 0.045 to 50 Economy
6
85056K
2.92 mm 0.045 to 50 Economy
85058D 1.85 mm 0.045 to 65 Standard
X11644A WR-90 8.2 to 12.4 Precision
P11644A WR-62 12.4 to 18 Precision
K11644A WR-42 18 to 26.5 Precision
R11644A WR-28 26.5 to 40 Precision
Q11644A WR-22 33 to 50 Precision
U11644A WR-19 40 to 60 Precision
V11644A WR-15 50 to 75 Precision
W11644A WR-10 75 to 110 Precision
2
Unless stated otherwise, all calibration kits are 50 ohms.
3
Economy calibration kits contain fixed loads.
4
Standard calibration kits contain sliding loads.
5
Precision calibration kits contain TRL calibration standards.
6
Option 001 adds a sliding load.
Verification Kits
Verification Kit 85029B 85051B 85053B 85055A 85057B R11645A Q11645A U11645A V11645A W11645A
Connector Type 7 mm 7 mm 3.5 mm Type-N 2.4 mm WR-28 WR-22 WR-19 WR-15 WR-10
Frequency Range DC to 6 0.045 0.045 0.045 0.045 26.5 to 40 33 to 50 40 to 60 50
(GHz) to 18 to 26.5 to 18 to 50
to
75 75 to 110
Network Analyzer Accessories
Test Port Cables and Adapters
Test port cable and adapter sets are available for
various connector types. The cable/adapter configurations are described below. All cables are designed with
one end that connects directly to the special rugged
ports of the network analyzer test set, and one end
that connects to the device under test.
Special test port adapter sets are also available to
convert the rugged ports of the network analyzer
test set to the desired connector interface. Each kit
contains two adapters, one male and one female.
Cables and special adapters have a 3.5 mm or 2.4 mm
ruggedized female connector on one end which is
designed to connect to HP network analyzer two-port
test sets. This connector cannot be mated to standard 3.5 mm or 2.4 mm connectors. However, the
other end of the cable or adapter has a connector
that can be mated to standard 3.5 mm or 2.4 mm
connectors.
77
Test port cables are available for two test configurations as shown below. Configuration Autilizes a
single test port cable for use when the device under
test (DUT) is connected directly to the port on the
test set. Configuration B utilizes two test port cables.
It provides more flexibility since the DUT is connected between the test port cables. See next page
for recommended cables/adapters associated with
each configuration.
Configuration A
Network Analyzer
Network Analyzer
Test Set
Test Set
Test
Set Port
Device
Under
Test
Test
Port Saver
Single Cable
11
Configuration B
Network Analyzer
Test Set
Cable Set
Device
Under
Test
78
Network Analyzer Accessories
Configuration A
3.5 mm test set ports
DUT
Connector Cables/adapters
3.5 mm HP 85131C Semi-rigid Cable with a 3.5 mm (f) connector
HP 85131E Flexible Cable with a 3.5 mm (f) connector
HP 85130D Adapter Set with 3.5 mm (m,f) connectors
7 mm HP 85132C Semi-rigid Cable with 7 mm connector
HP 85132E Flexible Cable with a 7 mm connector
HP 85130B Adapter Set with 7 mm connectors
Type-N Use 7 mm cables and the 7 mm to Type-N adapters
included in the HP 85054B,D calibration kit.
Configuration A
2.4 mm test set ports
DUT
Connector Cables/adapters
2.4 mm HP 85133C Semi-r igid Cable with a 2.4 mm (f) connector
HP 85133E Flexible Cable with a 2.4 mm (f) connector
HP 85130G Adapter Set with 2.4 mm (m,f) connectors
3.5 mm HP 85134C Semi-r igid Cable with a 3.5 mm (f) connector
HP 85134E Flexible Cable with a 3.5 mm (f) connector
HP 85130F Adapter Set with 3.5 mm (m,f) connectors
7 mm HP 85135C Semi-rigid Cable with a 7 mm connector
HP 85135E Flexible Cable with a 7 mm connector
HP 85130E Adapter Set with 7 mm connectors
Configuration B
3.5 mm test set ports
DUT
Connector Cable set
3.5 mm HP 85131D Semi-rigid Cable Set with 3.5 mm (m,f) connectors
HP 85131F Flexible Cable Set with 3.5 mm (m,f) connectors
7 mm HP 85132D Semi-rigid Cable Set with 7 mm connector
HP 85132F Flexible Cable Set with 7 mm connector
Type-N Use 7 mm cables and the 7 mm to Type-N adapters
included in the HP 85054B,D calibration kit.
Configuration B
2.4 mm test set ports
DUT
Connector Cable set
2.4 mm
3.5 mm
7 mm HP 85135D Semi-rigid Cable Set with 7 mm connectors
HP 85133D Semi-rigid Cable Set with 2.4 mm (m,f) connectors
HP 85133F Flexible Cable Set with 2.4 mm (m,f) connectors
HP 85134D Semi-rigid Cable Set with 3.5 mm (m,f) connectors
HP 85134F Flexible Cable Set with 3.5 mm (m,f) connectors
HP 85135F Flexible Cable Set with 7 mm connectors
Accessories
HP 86211A 75 ohm type-N to type-F adapter kit
Adapter kit which provides type-N to type-F adapters
necessary when measuring type-F devices on a
network analyzer with 75 ohm type-N test ports.
HP 11742A Blocking Capacitor
The HP 11742A blocking capacitor blocks dc signals
below 45 MHz and passes signals up to 26.5 GHz.
Ideal for use with high frequency oscilloscopes or
in biased microwave circuits, the HP 11742A will
suppress low frequency signals that can damage
expensive measuring equipment or will affect the
accuracy of your RF and microwave measurements.
Loading...