Agilent 83751A User’s Guide

User’s Guide

HP 83751A/B and
HP 83752AlB
Synthesized Sweepers

HP part number:
Printed in USA

Serial Numbers.

83750-90004

March 1996

This manual applies directly to instruments with serial prefix

3610A

and

below.

This manual also applies to Ermware revision 2.0 and above. For Ermware
revisions below 2.0 contact your nearest Hewlett-Packard service center for a
Ermware upgrade.

Notice.

The information contained in this document is subject to change without
notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,
including but not limited to, the implied warranties of merchantability and
Etness for a particular purpose. Hewlett-Packard shall not be liable for errors
contained herein or for incidental or consequential damages in connection
with the furnishing, performance, or use of this material.

@Copyright Hewlett-Packard Company 1993, 1996
All Rights Reserved. Reproduction, adaptation, or translation without prior
written permission is prohibited, except as allowed under the copyright laws.

1400 Fountaingrove Parkway, Santa Rosa, CA 95403, USA

The HP 8375lA/B and HP
Synthesized Sweepers

83752A/B

The HP 83751AA and HP

“sweepers” throughout this manual) provide continuous analog or digital
stepped sweep capability. The HP
2 to 20
to 20
high power output (approximately + 17
sweepers are SCPI and
for drop-in replacement of an HP 8350 sweep oscillator. The sweepers are
designed for optimum use with HP 8757 scalar analyzers. For specillcation
and option information, refer to Chapter 17, “Specilkations and Options,” in
this manual.

This User’s Guide is written to provide operating information to the user who
is comfortable with the front panel layout and basic operation of the sweeper.
For installation and basic sweeper operation, refer to the HP

HP

provided with your shipment.

GHz,

while the HP

GHz.

The “B” versions of both the HP 83751 and HP 83752 provide

83752A/B

S~thesized Sweepers Installation and Quick Start Guide,

83752A/B

83752A/B

HP-II3

programmable, with HP 8350 HP-IB mnemonics

synthesized sweepers (referred to as

83751A/B

provides a frequency range of 10 MHz

provides a frequency range of

dBm

maximum leveled power). The

83751A/B

and

. . .

111

The Synthesized Sweeper at a Glance

The following Egure and accompanying text explain some features of the
sweeper.

iv

pg425ab

The Synthesized Sweeper

1. The

(m)

are used to save and subsequently recall
sweeper operating parameters from one of
nine nonvolatile register locations.

2. The line POWER switch turns the sweeper
to either on or standby.

3. The Marker keys allow selection of up to
ten markers to be set anywhere within the
current frequency range. Marker A
measurements are made using these keys as
well.

4. The Modulation keys allow selection of
pulse, AM, or FM modulation.

6. The SWEEP OUT BNC connector provides
voltage proportional to the sweep ranging
from 0 V et the start of a sweep
at the end of the sweep, regardless of sweep
width.

6. The Automatic

[AK INI

path to the sweeper when its RF output
power level is being leveled externally.

7. The Power keys allow selection of the RF
output power level of the sweeper, as well
as other power related functions, such as
Automatic Level Control

[ALC

MODE 0) key is used to select

the method used to regulate the sweeper
output power level. Either internal leveling or
external leveling [with a diode, power meter,
or source module] can be selected. Additional
equipment is required when external leveling
is used.

and

(m)

level

Control voltage input

connector is used as the feedback

IALCI.

keys

to’+10

The

V

6. The date entry keys are used to enter
and/or modify various sweeper parameters.
The @ key cancels all or part of an
erroneous parameter entry before it has been
terminated. The terminator keys
rightmost column of keys) are used to choose
the units for the entered parameter as well
as to terminate the oarameter entry. The

a, 0,

used to increase or decrease a parameter in
predetermined steps.

9. The
toggle the RF output power on and off.

and

(-SIZE)

(RF

ON/OFF) key is used to

[the

keys are

10. The RF OUTPUT connector mates with

a female

APC-3.5mm

standard instruments. The connector metes
with a type-N male connector on option
instruments. The RF OUTPUT connector will
be found on the rear panel of sweepers with
option

lE4.

precision connector on

1ED

11. The front panel knob is used to increase

or decrease active parameters under the
pointers, and is used in manual frequency and
power sweeps.

12. The displays show the current values of
sweeper parameters as well as the status of
many of the sweeper functions. The left-hand
display shows the current frequency status,
whether it be swept or CW. The right-hand
display shows current marker, modulation end
sweep status parameters when they are
selected, as well as the current output power
level. The annunciators that appear below
the parameters are only visible when their
associated function is active. For example, the

STEP annunciator will only be visible when

operating in stepped sweep mode.

13. The Frequency keys are used to set the

various frequency parameters for the sweeper.
Swept frequency selections include Start/Stop,

CWSpan

and Marker 1 + Marker 2
functions. Continuous Wave
also be selected for- outputting single
frequencies.

14. The

(w)

the instrument into a known state. There are
two preset modes: the factory mode, and a
user-defined mode.

15. The

(m)

of some of the kevs. When vou

(m)

the sweeper performs the function printed in

blue above the key.

key changes the function

key and then press

ICWl

mode may

key is used to put

mess

the

enother

key,

Sweeper rear panel features are depicted and described in detail in Chapter 7,

“Front/Rear Panel” in this manual.

V

In This Book

This book is divided into two sections: the task reference and the dictionary
reference. These sections are subdivided into chapters. The task reference

section (identified by light blue tabs) provides step-by-step instructions for
many of the tasks that you perform with your sweeper. The chapters in the
task reference section are as follows:

Chapter 1

Chapter 2

Chapter 3

“Performing the Operator’s Check, )) contains a procedure for

assuring you that your instrument is operating correctly.

“Externally Leveling the Sweeper, )) provides the
steps necessary to externally level your sweeper with
detectors/couplers/splitters, power meters, and source
modules.

“Generating a Stepped Sweep,” explains how to set up the
instrument to generate a stepped sweep.

Chapter 4 “Generating a Millimeter Signal,” illustrates the setups for

using a millimeter head with your option

Chapter 5

Chapter 6

The dictionary reference section (identified by dark blue tabs) provides
information about instrument features and functions. Information is divided
into chapters as follows:

Chapter 7

“Creating User Flatness Arrays,” explains how to create user
flatness correction arrays, which calibrate the power level at
a remote test port.

“Operating a Master/Slave Setup, ’ shows the steps necessary
to configure two sweepers for two-tone measurement
capabilities.

“Front/Rear Panel, ’ contains entries that explain different
aspects of the sweeper front and rear panel. (For example,
you turn to this chapter for information on the sweepers
various connectors).

1EE

sweeper.

Chapter 8

“Instrument State Keys,” explains the functions of the keys
in the Instrument State group.

Chapter 9 “Marker Keys,

Markers group.

vi

”

explains the functions of the keys in the

Chapter 10

“Modulation Keys,’ explains the functions of the keys in the

Mod group.

Chapter 11

Chapter 12

Chapter 13

Chapter 14

Chapter 15

Chapter 16

Chapter 17

Chapter 18

“Frequency Keys,” explains the functions of the keys in the

Frequency group.

“Sweep Keys,” explains the functions of the keys in the

Sweep group.

“Power Keys, ” explains the functions of the keys in the

Power group.

“Entry Keys,” explains the functions of the keys in the Entry

group.

“Special Functions,

explains the various selections in the

”

special functions menu, which is accessed by selecting

m

SPECIAL.

“Error Messages,” contains lists of the error messages that

might be generated during use of the instrument.

“Specifications and Options,” contains a list of the sweeper’s
warranted performance specifications and typical operating
parameters, as well as the various mechanical, electrical,
warranty, and documentation options that are available.

“Safety and Regulatory information, ’ contains required
regulatory and safety information that is not included
elsewhere in the instrument documentation.

Vii

Certification

Hewlett-Packard Company certihes that this product met its published
specifications at the time of shipment from the factory. Hewlett-Packard
further certifies that its calibration measurements are traceable to the United
States National Institute of Standards and Technology, to the extent allowed
by the Institute’s calibration facility, and to the calibration facilities of other
International Standards Organization members.

Regulatory

The “Safety and Regulatory Information” chapter contains regulatory
information.

Information.

Vlll

. . .

Warranty

This Hewlett-Packard instrument product is warranted against defects in
material and workmanship for a period of one year from date of shipment.
During the warranty period, Hewlett-Packard Company will, at its option,

either repair or replace products which prove to be defective.
For warranty service or repair, this product must be returned to a service

facility designated by Hewlett-Packard. Buyer shall prepay shipping charges
to Hewlett-Packard and Hewlett-Packard shall pay shipping charges to return
the product to Buyer. However, Buyer shall pay all shipping charges, duties,
and taxes for products returned to Hewlett-Packard from another country.

Hewlett-Packard warrants that its software and
Hewlett-Packard for use with an instrument will execute its programming
instructions when properly installed on that instrument. Hewlett-Packard
does not warrant that the operation of the instrument, or software, or
firmware will be uninterrupted or error-free.

LIMITATION OF WARRANTY

The foregoing warranty shall not apply to defects resulting from improper
or inadequate maintenance by Buyer, Buyer-supplied software or
interfacing, unauthorized modihcation or misuse, operation outside of the
environmental specifications for the product, or improper site preparation
or maintenance.

NO OTHER WARRANTY IS EXPRESSED OR IMPLIED. HEWLETT-PACKARD
SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

EXCLUSIVE REMEDIES

THE REMEDIES PROVIDED HEREIN ARE BUYER’S SOLE AND EXCLUSIVE
REMEDIES. HEWLETT-PACKARD SHALL NOT BE LIABLE FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER
LEGAL THEORY.

fumware

designated by

ix

Assistance

Product maintenance agreements and other customer assistance agreements
are available

Fbr

any assistance, contact your nearest

Ome.

Refer

for

Hewlett-Packard products.

Haolett-Packard

to the list of Sales and Service 0me.s

Sales and Service

on

the following page.

X

Hewlett-Packard Sales and Service Offices

IN THE UNITED STATES
California

Hewlett-Packard Co.
1421 South Manhattan Ave

PO.

Box 4230
Fullerton, CA 92631
17141 999-6700

Hewlett-Packard Co.
301 E. Evelyn
Mountain View, CA 94039
14151

694-2000

Colorado

iewlett-Packard

24 Inverness Place, East
Englewood, CO 80112

3031

Co.

649-5000

Georgia

iewlett-Packard
2000 South Park Place
?O.

Box 105005
Atlanta, GA 30339

Co.

4041 955-1500

:llinois

iewlett-Packard Co.

j201 Tollview
IoIling

3121

Drive
Meadows, IL 60008

255-9800

Yew Jersey

iewlett-Packard

120 W. Century Road

laramus,

201 I

Co.

NJ 07653

265-5000

rexas

hewlettPackard

130 E. Campbell Rd.

hchardson,

2141 231-6101

Co.

TX 75081

IN AUSTRALIA

Hewlett-Packard Australia Ltd.
31-41 Joseph Street
Blackburn, Victoria 3130
895-2895

IN CANADA

Hewlett-Packard

17500 South Service Road

Trans.Canada

Kirkland,
15141 697-4232

[Canada]

Highway

Quebec H9J 2X8

Ltd.

IN FRANCE

Hewlett-Packard France

F-91947 Les
Orsey
161 907-78-25

Ulis Cedex

IN GERMAN FEDERAL
REPUBLIC

Hewlett-Packard

Vertriebszentrale Frankfurt
Berner Strasse 117
Postfach 560 140

D-6000

Frankfurt 56

1061 II

GmbH

50-04-I

IN GREAT BRITAIN

Hewlett-Packard Ltd.
King Street Lane
Winnersh, Wokingham
Berkshire
0734 784774

RGll 5AR

IN OTHER EUROPEAN
COUNTRIES

Hewlett-Packard

Allmend

2

CH-8967

100411 57 31 21 11

[Schweizl

Widen [Zurich]

AG

IN JAPAN

Yokogawa-Hewlett-Packard Ltd.
29-21 Takaido-Higashi, 3 Chome
Suginami-ku Tokyo 168

1031 331-6111

IN PEOPLE’S REPUBLIC
OF CHINA

China Hewlett-Packard, Ltd.

PO. Box 9610, Beijing

4th Floor,

Main Bldg.
Shuang Yu Shu,
Beijing, PRC

256-6888

2nd

Watch Factory

Bei

San Huan Rd.

IN SINGAPORE

Hewlett-Packard Singapore

Pm.

Ltd.
1150 Depot Road
Singapore 0410
273 7388

Telex HPSGSO
Fax

1651

AS34209

2788990

IN TAIWAN

Hewlett-Packard Taiwan

8th Floor, Hewlett-Packard

Building
337 Fu Hsing North Road
Taipei

1021 712-0404

IN ALL OTHER LOCATIONS

Hewlett-Packard Inter-Americas
3495 Deer Creek Rd.
Palo Alto, California 94304

xi

Safety Notes

The following safety notes are used throughout this manual. Familiarize
yourself with each of the notes and its meaning before operating this
instrument.

CAUTION

WARNING

The caution note denotes a hazard. It calls attention to a procedure
if not correctly performed or adhered to, could result in damage to or
destruction of the instrument. Do not proceed beyond a caution note until
the indicated conditions are fully understood and met.

tihich,

The warning note denotes a hazard. It calls attention to a procedure
which, if not correctly performed or adhered to, could result in

iqiury

or

loss of life. Do not proceed beyond a warning note until the indicked
conditions are fully understood and met.

Instrument

Instruction

Manual

!

A

The

CE93

Markings.

The instruction manual symbol. The product is marked with this symbol when it is necessary
for the user to refer to the instructions in the manual.

mark shows compliance with European Community 1993 standards.

The CSA mark is the Canadian Standards Association safety mark.

The

&Ml-A

mark stands for Industrial Scientific and Medical Group 1. Class A.

xii

General Safety Considerations

WARNING

WARNING

WARNING

CAUTION

CAUTION

Before this

instrummt

is

switched on, make sure it has been properly

grounded through the protective conductor of the ac power cable to a

socket outlet provided with protective earth contact.

This is a Safety Class I product (provided with a protective earthing
ground incorporated in the power cord). Any interruption of the
protective (grounding) conductor, inside or outside the instrument, or

disconnection of the protective earth terminal can result in personal

injury.
No operator serviceable parts inside the instrument. Refer servicing to

qualified personnel. To prevent electrical shock, do not remove covers.
Any adjustments or service procedures that require operation of the
instrument with protective covers removed should be performed only by
trained service personnel.

For continued protection against fire hazard, replace line fuse only
with the same type and rating (F

6.3A/250V).

The use of other fuses or

material is prohibited.

If this instrument is used in a manner not specihed by Hewlett-Packard Co.,
the protection provided by the instrument may be unpaired.

Always use the three-pronged ac power cord supplied with this instrument.
Failure to ensure adequate earth grounding by using this cord may cause
instrument damage.

CAUTION

This instrument has automatic selection input. Be sure the supply voltage is
within the speciEed range.

Xlll

. . .

How to Use This Guide

This guide uses the following conventions.

(FRONT-PANEL

SHIFT FUNCTION

ANNUNCIATOR

KEY_)

This represents a key physically located on the
instrument.

This represents a shift function (blue text above
front panel keys).

Text in this font represents FREQUENCY,
MARKER/SWEEP/STATUS, and POWER displays.

Text in this font represents the annunciators that
are displayed in the lower portion of the sweeper
display.

Contents

1.

Performing

To run the
To run peak power-tracking
To

check

To

check

If

you

If the self-test
If the maximum leveled power

2. Externally Leveling the Sweeper

Leveling

External leveling with the option 1El
See

Leveling

See

Leveling with millimeter-wave source modules

(option

See

the Operator’s Check

full

self-test

the maximum leveled power
the output

have

a

problem

fails

with detectors/couplers/splitters

also

also

also

.....................

with

a

.....................

1EE

.....................

power meter

only)

................

power

.................

.................

................

..............

..............

check fails

..............

.........

step

.......

.......

attenuator

l-3

1-5
1-6

l-8

l-10
l-10
l-11

2-3

.

2-6

2-6
2-7
2-8

2-9

2-11

3.

Generating a
Generating a

4.

Using
Using

Creating

5.

Creating

Creating a user flatness array for use in a scalar analysis

millimeter heads with “B” model

(high power) sweepers ................

millimeter heads with “A” model

(standard power) sweepers

See also

To

set up the sweeper ...............

To

set up the power meter

To

start the user flatness cal

measurement

To

set up

Stepped Sweep
Millimeter Signal

..............

.....................

User Flatness Arrays

a

user flatness array

..................

the sweeper

.............

.............

............

...............

4-3
4-5

4-6

5-3
5-4
5-5
5-5

5-6
5-7

Contents-l

To

To set

To start the user flatness cal
To reactivate the

6.

Operating a

To

set up

To

set up

See

set up

also

the analyzer

up

the power meter

HP

Master/Slave

the master sweeper
the

slave

sweeper

......................

...............

..........

...............

8757 system interface

Setup

.............

..............

......

5-7

5-8

5-8

5-9

6-4
6-6
6-7

Front/Rear

7.

Connectors

BNC

Panel

.....................

Connectors

Multi-pin Connectors

AUXILIARY
HP-IB

.....................

SOURCE MODULE INTERFACE (Option

RF Output Connector

Display

......................

Frequency Display
Marker/Sweep/Status and Power
Annunciators

HP-IB Lang/Address Switch

See

Knob

Also

.....................

.......................

Equivalent SCPI Commands

Line

POWER Switch

Power

Cables

Instrument

....................

State

.....................

.....................

.....................

.....................

.....................

.....................

.................

...............

INTERFACE

...............

.................

...................

................

Keys

............

Display

.............

............

.......

1EE

Only)

7-3
7-5
7-8

7-8
7-10
7-13
7-15
7-16
7-17
7-18

7-19

7-23
7-25
7-26
7-26
7-27

7-29

8-3

8-4

8-6

8-8

B-10

8-11

Contents-2

9.

Marker

(iziG)

........................

m
(MKRa_l

.......................

10.

Modulation Keys

(PULSE MODE

(AMMODEU

(FM MODE

Keys

........................

8)

...................

....................

$1.

....................

11.

...............

...................

...................

...................

...................

...................

12.

Sweep Keys

ITIME) . . .

(TRIG MODE
[SINGLE/TRIG)

13.

Power Keys

(POWER LEVEL]

@OWER/SWEEP)
[ALC

MODE 3) . . . . . . . . . . . . . . . . . . . .

(FLTNEss ON/OFF_) . . . . . . . . . . . . . . . . . . .

....................

....................

Q)

....................

....................

...................

9-4
9-7
9-8

10-4

10-6

10-7

....

.

11-4
11-6
11-8

11-9
11-10
11-12

12-4

12-7

12-10

13-3

13-5
13-7

13-10

14.

Entry

Q)a
@EEiz)

......................

Number Pad Keys
Unit

Keys

(j-ON/OFF)

......................

*+.
ENTRY OFF

PEgK

Keys

.......................

.....................

......................

.....................

.......................

..................

14-3
14-4
14-5
14-6
14-7

14-8
14-9

14-10

Contents-3

15.

Special

Functions

l- CWCFAUTO . . . . . . .

2 - CW PEAKNG . . . . . . . .

3 - SWPTIME AUTO . . . . .

4 - STEP SWPTIME . . . . ,

5 - SWPTIME

LLIM . . . .

6 - ATT COUPLING . . . . .

7 - ATT SETTING . . . . . .

8 -

ROSC

9 -

ROSC

10 - V/GHz

AUTO

SOURCE : : : : : :

SCALE . . . . .

11- V/GHz OFFSET . . . . .

12-PWRMETERTY

13-PWRMETERAD

14 -

FM

SENSITIVITY . . . .

15 - LANGUAGE . . . . . . .

16 - FW REVISION . . . . . .

17 -

*SECURITY

18 - DP DEFIN : : : ‘. ‘. ‘. ‘. ’ .

19 - CONTROL MODE . . . .

21-

FULL

SELFTST . . . . .

. . .
. . .

...........

...........

...........

...........

.

...........

...........

...........

...........

...........

.

...........

...........

.

...........

.

...........

...........

...........

...........

...........

............

...........

...........

15-6

15-7

15-8

15-9
15-10

15-11
15-12
15-13
15-14
15-15
15-16
15-17
15-18
15-19
15-20
15-21

15-22

15-26
15-27
15-28

16. Error

The Error/Event Queue
Error numbers

Error
SCPI Error

Contents-4

Messages

................

....................

Messages List

Messages

Command Error
Execution Error
Device-specific Error
Query Error

Instrument
Block
Bus
Parsing and Compatibility Errors
Diagnostics and
Internal Hardware Errors

Hardware Configuration Errors

Calibration Routine Errors
Loops
Miscellaneous Hardware Dependent Errors

Specific

Transfer Errors

Control Errors

Unlocked Errors

.................

................

...................

..................

................

....................

Error

................

Self-test

Messages

...............

Errors

..............

.............

...............

.........

..........

...........

...........

......

16-3

16-4

16-5
16-7

16-7

16-13

16-19

16-21

16-23
16-23
16-24
16-25
16-28
16-32
16-32
16-33
16-35
16-36

17.

Specifications and

Specifications
Frequency

Range
Timebase Stability

CW
Stepped
Ramp (Analog)
Bandswitch Points

RF Output

Maximum
Minimum Settable
Resolution
Accuracy and Flatness

Power Sweep
Power Slope

External

User

Source Match

Spectral Purity

Harmonics (at max leveled power)

Subharmonics

Non-harmonic Spurious

Residual

Modulation

Pulse

AM

FM

General

Compatibility : : : :

Programming

Master/Slave (two-tone) Measurements

Environmental

Warmup Time

Power

Dimensions

Weight

Options

Electrical Options

Option 1El - Add Output
Option lE4 - Rear Panel RF Output

Options

....................

.....................

......................

Mode

Flatness

.......................

.......................

....................

Sweep Mode

Sweep

.....................

Leveled

Power

....................

...................

...................

Leveling

(Level)

...................

...................

...............

FM (0.05 to 15 kHz

.....................

......................

................

...................

..................

..................

Requirements

....................

......................

......................

.................

...............

Mode

.................

Power (25 f5

..............

...............

.................

Correction

..............

bandwidth)

...............

................

.................

Step

............

“C)

..........

..........

Attenuator

.........

........

.......

.......

17-3
17-4
17-4
17-4
17-4
17-5
17-5
17-5
17-7
17-7
17-8
17-8
17-8
17-9
17-9
17-9

17-9
17-10
17-11
17-11

....

....

.

17-11
17-11
17-12
17-13
17-13
17-13
17-14
17-15
17-15

17-15
17-15

17-16

17-16
17-17
17-17
17-18
17-19
17-19
17-19
17-19

Contents-5

Option lE5 - Add

Option

Option

Mechanical Options

Option 1CM ­Option
Option

Warranty Options

Option

Option
Option

Option

Documentation Options

Option OB2 - Extra Operating Documentation

Option

Certification Options

Option 1BN - Certification

Option

18.

Safety and

Regulations and Licensing

Notice

Safety

Statement
Environmental Conditions

Ventilation Requirements

Cleaning Instructions

1ED

1EE - Source

Cable

1CP - Rack
AX2 -

W30 - Two

Service

W50 ­ W52 -

Service

W54 -

OB3 - Service

1BP -

Regulatory

for

Information

of

High

.

Type-N RF

....................

Rack

Portable Handle and Front-panel

.................

...................

Five
Five

...................

Five

Certification with Data

Germany:

..................

Compliance

Stability Timebase

Output

Module Connector and Extension

................

Mount Kit without Handles

Mount Kit with Handles

Additional Rears Return-to-HP

Year
Year

Year MIL-STD

..............

Documentation

................

Information

..............

Noise

..............

..............

...............

Connector

Return to
Return-to-HP Calibration

............

Declaration

.............

HP

Repair

Calibration

.......

.......

........

.....

......

. .

....

Cover

Service

Service

...

17-19

17-19

17-20
17-20
17-20
17-20
17-20
17-21

17-21
17-21

17-21
17-21
17-22
17-22
17-22
17-22
17-22
17-22

18-3

18-3
18-8
18-8
18-8
18-9
18-9

Index

Contents-6

Figures

l-l. The UNLEV Annunciator Location ............. l-7

l-2. Connections for Checking Output Power ..........

2-l.

ALC Circuit Externally Leveled ..............

2-2. Typical Diode Detector Response at 25

2-3. Leveling with a Power Meter ...............

2-4. Millimeter-wave Source Module Leveling ..........

2-5. Millimeter-wave Source Module Leveling Using a Microwave

Ampliher ......................

4-1. Millimeter-wave Source Module Leveling ..........

4-2. Millimeter-wave Source Module Leveling Using a Microwave

Amplifier ......................

5-1. Creating a User Flatness Array ......... .....

5-2. Scalar Measurement System Setup ............

6-l.

Master/Slave Setup ...................

7-l.

Sweeper Connectors - Front Panel .............

7-2. Sweeper Connectors - Rear Panel .............

7-3. Auxiliary Interface Connector ...............

7-4. HP-B Connector and Cable ................

7-5. Interface Signals of the Source Module Connector ......

7-6. Sweeper Display ............... .....

7-7. Sweeper Display and LED Annunciators ..........

7-8. HP-B Address Switch Settings ..............

7-9. Instrument Language Switch Settings ...........

7-10. Clear Register Contents Settings .............

7-l 1. The Sweeper Line POWER Switch .............

7-12. Power Cable and Line (Mains) Plug Part Numbers ......

8-l.

Instrument State Group .................

9-l.

The Markers Group ...................

10-l. The Modulation Group ...................

11-l. The Frequency Group ..................

12-1. The Sweep Group ....................

13-1. The Power Group ....................

14-1. The Entry Group ....................

15-1. The Instrument Group ..................

17-l. Typical Swept Frequency Accuracy (100 ms sweep, ramp

mode) .......................

17-2. Typical Maximum Available Power ............

“C

.........

l-8

2-3
2-5
2-7
2-9

2-10

4-4

4-6

5-3
5-6

6-3

7-3

7-4

7-8

7-10

7-13

7-16

7-19

7-23

7-24
7-24

7-27

7-30

8-2

9-2
10-2
11-2
12-2
13-2
14-2
15-2

17-6

17-7

Contents-7

Contents

17-3. Typical Phase Noise (10
17-4. Dimensions

.......................

GHz

Carrier)

...........

17-12
17-17

Contents-8

l%bles

7-l.

Pin Description of the Auxiliary Interface

8-l.

Factory Preset Conditions

14-1. Step Sizes

15-1. Special Functions for the HP 83750 Series Sweepers
15-2. FM Sensitivity When Using Source Modules

.......................

................

.........

........

....

7-9

8-4

14-3

15-4

15-19

Contents-9

1

Performing the Operator’s
Check

Performing the Operator’s Check

The operator’s check consists of a series of tasks that, when completed, will
either assure you that your instrument is operating correctly, or will help
to point to problem areas if it is not. The operator’s check
performance to specifications.

The operator’s check should be performed on a weekly basis, or whenever
the integrity of the sweeper is in question.

To perform the operator’s check, the following tasks should be performed, in
order:

1. Run the full self-test.

2. Run peak power-tracking.

3. Check the maximum leveled power.

4. Check the output power.

does

not ensure

l-2

To run the full self-test

Attention!

All external cables [including HP-IB and BNC cables) must be disconnected from the sweeper prior to
running the full self-test. Failure to do so may cause self-test failures or lock-ups.

1. Disconnect all external cables prior to running the self-test.

2. Activate the FULL SELFTST special function by pressing the following
keys on the sweeper:

The message that appears in the MARKER/SWEEP/STATUS display is
one of the following:

Full self-test has not been performed
since the last time the line power was
turned on.

Full self-test has been performed and
passed all tests.

Full self-test has been performed, and
test XXXXXX was either the only test
that failed, or was the most significant
failure.

3. Press the

While the self-test
appear in the MARKER/SWEEP/STATUS display.

(jj)

key again to initiate the self-test routine.

routine is running, a

M++I,,I.~ i t. ++s+

message

wfll

l-3

Performing the Operator’s Check

To run the full self-test

4. When the self-test routine is

mushed,

a message will appear in the

MARKER/SWEEP/STATUS display. If the message does not say

“Ful 1

Ted PHASED,”

refer to the section entitled “If You Have a

Problem” at the end of this chapter.

The full self-test is actually a series of tests performed to check different
instrument functions. If the sweeper fails just one test, the display shows the
title of the failed test. If the instrument fails more than one test, the test title
shown is the most signilicant failure.

1-4

lb run peak power-tracking

1. Before running peak power-tracking, make sure the RF OUTPUT is either
connected in a 50 0 system, or has a load on it, such as a power sensor or
attenuator.

CAUTION

For optimum power at all frequencies, do not run peak power-tracking with a
millimeter head connected to the sweeper.

2.

Press (PRESET)

Cm)

P&W .

The MARKER/SWEEP/STATUS display shows the progression of the sweep
as the instrument adjusts the power-tracking.

When you run peak power-tracking (or autotracking), the instrument
optimizes its output power over the sweeper’s full frequency range by
tracking the output

NOTE

Peak power tracking takes approximately 1 to 3 minutes to complete, and can be aborted by pressing

(EEFi],

if necessary.

titer

with the RF source output.

1-5

lb check the maximum leveled power

1. Before checking maximum leveled power, make sure the RF OUTPUT is
either connected in a 50 61 system, or has a load on it, such as a power
sensor or attenuator.

2. Press [PRESET).

3. Press [POWER LEVEL) and enter the specified maximum leveled power for
your instrument. (For an HP
< 2

GHz.)

HP
HP 837518”
HP

< 2

>

83751N33752A

837528”

2

GHz

83752B,

GHz

set the power to the

+lO dBm
+17 dBm

+16 dBm
+17 dBm

specikation

for

*

Option

1El

[step attenuatorl, reduce by 1

dB.

4. Make sure the UNLEV annunciator is not lit at any time. The UNLEV
annunciator is located in the POWER display area. (See Figure l-l.)

5. Press

m

@

cm)

to change the sweep time to 2 seconds.

6. Press [SINGLE TRIG] and make sure the UNLEV annunciator does not come
on at any point during the sweep. (If the annunciator comes on, it

indicates the instrument is unleveled.) The UNLEV annunciator is located

in the POWER display area. (See Figure l-l.)

1-6

Performing the Operator’s Check

To check the maximum leveled power

\

000 0 000 0 00000

00

00

:a::

For HP

The HP

7. Press the following keys to set a sweep range of 2
power level of 17

(START_) 0 @iqGqLq)

[POWER

0 0 000 0 00000
0 0 000 0 00000

-*

0

0

0’0

Figure l-l. The UNLEV Annunciator location

83752B

83752B

Instruments Only.

sweepers have a power specification that is split at 2

dBm

mm) 117)

(or

000000

(or 16

dBm

for instruments with option

[16)) [GHz/dB(mL)

0

0

0

GHz

’

to 20

UNLEV
ANNUNCLATOR

tiEARS

pg426ob

GHz.

GHz

and a

1El):

8. Press @NGLE

TRIG_)

and make sure the UNLEV annunciator does not come

on at any point during the sweep. (If the annunciator comes on, it
indicates the instrument is unleveled.) The UNLEV annunciator is located
in the POWER display area. (See Figure l-l.)

l-7

To check the output power

1. Connect the equipment as shown.

POWER METER

SENSOR

SYNTHESIZED SWEEPER

RF OUTPUl

I

POWER SENSOR ADAPTER

Figure 1-2. Connections for Checking Output Power

2.

Press (PRESET_).

3. Press ccw)

4. Press

you set. Refer to the following table. Terminate the power level entry by
pressing

(ZiJ CGHz/dB(mL).

POWER

LEVEL) and enter the specified power for the CW frequency

(GHz/dB(mZ).

Instrument

Maximum leveled

Power Specification

pg427ob

l-8

HP

83751Ml3752A”

HP 837518”

HP 837528”

< 2

1

2

1 *

Option

+I0 dBm
+I7 dBm

GHz

GHz

IEI

lstep attenuetorl, reduce by 1

+I6 dBm
+I7 dBm

dB.1

Performing the Operator’s Check

To check the output power

5. Set the power meter calibration factor to the value listed on the power
sensor that corresponds to the frequency you set.

6. Verify that the measured output power meets the instrument specification.

l If the measured value is less than the specihed power, turn the front

panel knob until the value measured is at least the speciEed power level.

l Make sure that the UNLEV annunciator doesn’t light. (If the annunciator

does light, this indicates an unleveled condition.)

7. Repeat steps 3 through 6 for the following setting(s):

2.5

GHz

1.5

GHz -

for HP

83752AA

instruments only

50 MHz - for HP

83752A/B

instruments only

l-9

If you have a problem

If you have a problem while performing the operator’s check, check the
following list of commonly encountered problems. If the problem you have
encountered is not here, contact the nearest Hewlett-Packard office for
assistance.

If the self-test fails

The self-test has failed if the message that appears when it is done, is
anything except

q Make sure all external cables are disconnected from the sweeper and run

the self-test again.

Full Test.

PHSSED.

q If the test still fails, send the instrument to an HP service center for repair,

including a description of the failed test and any other error messages.

NOTE
If you need to ship your sweeper, remove the front handles (if so equipped) and use the original

packaging (or comparable).

l-10

Performing the Operator’s Check

If the maximum leveled power check fails

q Make sure that the RF OUTPUT connector was terminated before the peak

power-tracking sequence was run, and before the maximum leveled power
check.

q Make sure the power you entered in steps 2 and 5 of the maximum leveled

power check procedure are correct for your particular instrument.

q

If

the measured value of power in step 6 of “To check the output power” is

mo?-e

than the specified power, turn the front panel knob counterclockwise
until the value measured equals the specified power. Note the sweeper’s
front panel reading and use this value to repeat the maximum leveled
power check.

q If the check still fails, contact the nearest Hewlett-Packard office for

assistance.

NOTE

If you need to ship your sweeper, remove the front handles
packaging (or comparablel.

(if

so equipped) and use the original

l-11

2

Externally Leveling the Sweeper

Externally Leveling the Sweeper

In externally leveled operations, the output power from the sweeper is

detected by an external sensor. The output of this detector is returned to the

leveling circuitry, and the output power is automatically adjusted to keep

power constant at the point of detection.

2-2

Leveling with detectors/couplers/splitters

1. Connect the equipment as shown in Figure 2-1.

SYNTHESIZED SWEEPER

DIRECTIONAL COUPLER

OR POWER

SPLITTER)

pg417ab

Figure 2-1. ALC Circuit Externally leveled

2. Press

shows

[ALC

MODE

8)

repeatedly until the MARKER/SWEEP/STATUS display

HLC=

Diode. Note that the EXT ALC annunciator is lit.

3. Enter the coupling factor by selecting
the desired number.

m

LEVELED

OUTPUT

EXT CAL and then entering

2-3

Externally Leveling the Sweeper

leveling with detectorslcouplerslsplitters

NOTE

The coupling factor (in

leveled power (P

locations of P lev and P det. After the coupling factor has been entered, the front panel knob
may be used to fine tune the displayed power to equal the actual leveled output power (P levl.

Figure

2-l

illustrates a typical setup for external leveling. When externally

dB)

is defined by the equation

lev) -

detected power (P

det).

Refer to Figure ‘2-1 for

leveled, the power level feedback is taken from the external negative detector

input rather than the internal detector. This feedback voltage controls the
ALC system to set the desired RF output.

Figure 2-2 shows the input power versus output voltage characteristics for

typical HP diode detectors. From the chart, the leveled power at the diode
detector input resulting from any external level voltage setting may be
determined. The ALC feedback voltage present at the output of the detector
must be between -0.2 mV and -0.5 V. For a typical

corresponds to a detector input of approximately -35

HF’

diode detector, this

dE%m

to +5

dBm.

(See

Figure 2-2.)

2-4

Externally Leveling the Sweeper

leveling with detectors/couplers/splitters

10 v

1.0

100 mv

10

mv

1 mv

+20

dBV

+lO

dBV

+6

dBV

v

0 dBV

-10

dBV

-20

dBV

-30

dBV

-40

dBV

-50

dBV

-60

dBV

-66

dBV

-70 di3V

.I mv

-40 -30

-

DETECTOR INPUT POWER,

0

+10 +20 f30

Figure 2-2. Typical Diode Detector Response at 25

dBM

-80

dBV

pg431ob

‘C

2-5

Externally leveling the Sweeper

leveling with detectors/couplers/splitters

External leveling with the option 1El step attenuator

Some external leveling applications require low output power from the
sweeper. The sweeper automatically uncouples the attenuator from the ALC

system for

the UNCPLD annunciator is lit.

For example, leveling the output of a 30 dB gain amplifier to a level of

-

10
leveled. At some frequencies this level is beyond the range of the ALC
modulator alone. If so, the UNLEV warning message is displayed. Inserting 40

dB

of attenuation results in an ALC level (power level + attenuator value) of

0

dBm,

AM or other functions that vary the power level.

all

external leveling points. Note that in external leveling modes,

dBm

requires the output of the sweeper to be around -40

which is well within the range of the ALC. This gives a margin for

dBm

when

The ALC level should be greater than or equal to -10
sweepers (standard power), and -5
power). Adjust the attenuator so that the ALC level is within the specified
power range of your sweeper. For an “A” model sweeper, this is achieved by
using attenuation equal to the tens digit of output power. Example: for a
desired sweeper output power of -43

1.

Press

2. Set the attenuator to 40

CSHIFT)

SPECIAL

(YJ

dB:

press

dBm

for “B” model sweepers (high

dBm;

do the following:

c40) [GHz/dB(mL)

dBm

for “A” model

See also

To obtain flatness corrected power refer to the chapter entitled “Creating User

Flatness Correction Arrays, n later in this manual.

2-6

Leveling with a power meter

Leveling with a power meter is similar to leveling with a diode detector.

1. Set up the equipment as shown in Figure 2-3. Be sure to set the power
meter to the correct manual range mode for the output power setting at
which you are leveling.

POWER
METER

=j-$g;pLER

POWER SENSOR

I

Figure 2-3. leveling with a Power Meter

2. Press

3. Select

shows

(ALC

MODE $J repeatedly until the MARKER/SWEEP/STATUS display

ALC= Pcllwr Met.w-.

m

EXT CAL @

Note that the EXT ALC annunciator is lit.

CGHz/dB(mL).

enter the coupling factor of the coupler.)

LEVELED

OUTPUT

pg418ab

(If a directional coupler is used,

2-7

Externally leveling the Sweeper

leveling with a power meter

NOTE

The coupling factor is defined by the equation

leveled power (P

locations of P lev and P det. After the coupling factor has been entered, the front panel knob
may be used to fine tune the displayed power to equal the actual leveled output power fP lev).

lev) -

detected power (P

det).

Refer to Figure 2-1 for

4. If the power meter and the sweeper power setting don’t agree, set the
coupling factor step size to 10 dR and then use the a Q) keys to adjust
the coupling factor up or down until the power meter and the sweeper
power setting agree.

5. Select the sweep tune by pressing

I‘TIME)

and then entering the desired

sweep rate.

NOTE

Due to the settling time required by power meters, it is recommended to use a 40 second sweep rate.

Unlike detector leveling, power meter leveling provides calibrated power out
of the leveled RF port.

See also

To obtain flatness corrected power refer to “Creating User Flatness Correction
Arrays, n later in this manual.

2-8

Leveling with millimeter-wave source modules (option 1EE only)

Millimeter-wave source module leveling is similar to power meter leveling,
except that a slow sweep time is not required. Figure 2-4 and Figure 2-5
illustrate the setups for leveling with a mm-wave source module.

Figure 2-4 illustrates the setup that is used with the HP
HP

83752B

(high power models). No external amplifier is required to obtain

maximum specified power. The interface extender cable

83751B

(HP

part number

5062-7202) allows the source module to be positioned in front of the sweeper.

SOURCE MODULE
I NTERFACE

RF

OUTPUT

ADAPTER

( IF

REQUI

RED)

MM-WAVE SOURCE

RF IN

MODULE

b LEVELED

OUTPUT

and

Figure 2-4. Millimeter-wave Source Module leveling

pg420ob

2-9

Externally leveling the Sweeper

Figure 2-5 illustrates the setup that is used with the HP
HP

83752A

(standard power models). An external amplifier is required to

obtain maximum specified power.

SOURCE MODULE
I NSERFACE

RF OUTPUT

I

INTERFACE
EXTENDER
CABLE

I

ADAPTER

(IF REQUIRED)

MICROWAVE

AMPLIFIER

\

-cxJ@

0

0

RF IN

C

RF OUT

W-WAVE SOURCE

MODULE

83751A

and

LEVELED
OUTPUT

Figure 2-5. Millimeter-wave Source Module leveling Using a Microwave Amplifier

1.

Turn the sweeper line power off.

2. Set up the equipment as shown in Figure 2-4 or Figure 2-5.

3. Turn the sweeper line power on and press

4. When the

c-j

key is pressed, the sweeper configures itself for source

C-1.

module operation, and all of the ALC data necessary to communicate
properly with the sweeper is exchanged via the rear panel SOURCE
MODULE INTERFACE. Note that the EXT ALC annunciator is lit, and that

the POWER display shows the millimeter head output power.

2-10

Externally leveling the Sweeper

See also

To obtain flatness corrected power refer to “Creating User Flatness Correction
Arrays, )) later in this manual.

2-11

3

Generating a Stepped Sweep

Generating a Stepped Sweep

To generate a stepped sweep, perform the following steps:

1. Press (PRESET).

2.

Select the desired

3.

Select the desired number of points by pressing

entering the desired number.

4.

Press

m

SWEEP MODE $ .

5. Press the @J key. The MARKER/SWEEP/STATUS display should read

Sweep=

St>eF’

6. The instrument is now running in stepped sweep mode.

NOTE

The stepped sweep time is calculated by the following formula:

SteppedSweep

stepped sweep time can be changed in one of two ways:

(START_)

Iknt

Time = Dwell Time *Number of Points. Therefore the

and IsTopl frequencies.

(=I

and the STEP annunciator should be lit.

POINTS and

l By changing the dwell time. (Press
l By changing the number of points. (Press

3-2

CTIME)

while in stepped sweep

(GiiFF~ PDINTS .)

mode.1

4

Generating a Millimeter Signal

Generating a Millimeter Signal

If your sweeper was ordered with Option lEE, you have the capability of
using HP 83550 series millimeter head source modules with the sweeper. The
interface extender cable (HP part number 5062-7202) that is provided with all

option

sweeper.
After a source module is connected to the sweeper via the SOURCE MODULE

INTERFACE connector, the sweep will automatically configure itself for source
module operation when the line power is cycled, when the sweeper is preset,
or when a register is recalled.

1EE

sweepers allows the source module to be positioned in front of the

4-2

Using millimeter heads with “B” model
(high power) sweepers

Figure
HP

1.

2. Turn the sweeper on, and press

3. The sweeper automatically configures itself for source module operation

4-l

shows the equipment setup for using a millimeter head with your

83751B

Turn the sweeper line power off, and connect the equipment as shown in

Figure 4-

when the

or HP

1.

@EE]

83752B.

fjPRESET).

key is pressed.

4-3

Generating a Millimeter Signal

Using millimeter heads with “B” model

SOURCE MODULE

I NTERFACE

I NTERFACE
EXTENDER
CABLE

RF

OUTPUT

ADAPTER

(IF REQUIRED)

MM-WAVE SOURCE

MODULE

(high power) sweepers

Figure

4-l. Millimeter.wave

LEVELED

OUTPUT

pg420ab

Source Module leveling

4-4

Using millimeter heads with “A” model

(standard power) sweepers

Figure 4-2 shows the equipment setup for using a millimeter head with
your HP

maximum specihed power.

1. Turn the sweeper line power off, connect the equipment as shown in

83751A

Figure 4-1.

or HP

83752A.

An external amplifier is required to obtain

2. Turn the sweeper on, and press

3. The sweeper automatically configures itself for source module operation
when the (PRESET_) key is pressed.

(EE’EQ.

4-5

Generating a Millimeter Signal

SOURCE MODULE
INTERFACE

RF OUTPUT

I

ADAPTER

(IF REQUIRED)

NTERFACE

:XTENDER
:ABLE

MICROWAVE

AMPLIFIER

RF IN

Wd-WAVE

SOURCE

MODULE

b

LEVELED

OUTPUT

Figure 4-2. Millimeter-wave Source Module leveling Using a Microwave Amplifier

See also

To obtain flatness corrected power refer to “Creating User Flatness Correction

Arrays,” later in this section.

4-6

5

Creating User Flatness Arrays

Creating User Flatness Arrays

This chapter explains how to create user flatness correction arrays, which
calibrate the power level at a remote test port. Two examples are provided:

l The first example shows the basic setup and steps to create a user flatness

array.

l The second example shows how to set up a scalar analysis measurement

using a user flatness correction array.

5-2

Creating a user flatness array

In this example an HP
the interface bus

(HP-IB)

437B

power meter controlled by the sweeper through

is used to enter the correction data into a flatness

array.
Figure 5-l shows a typical system setup. The setup shown assumes that if

the setup has an external leveling configuration, that the steps necessary to
correctly level have been taken. Refer to Chapter 2, “Externally Leveling the
Sweeper, )) for information on external leveling.

1

CAmEs

DO/ICES

IFLATNESS

CORRECTED

,OUTPUT

i .-----,--,

OUTPUT

INPUT
PORT

I

,

I

;

TEST PORT

POWER SENSOR

-0-uq-J-N

“l%tE”E::

TEST

;ALC

INIRF

I

1

--------.

I

I

;

I

I

----d

AND OTHER

i

*- - - -,-- --’

----------

Figure

5.1.

Creating a User Flatness Array

5-3

Creating User Flatness Arrays

Creating a user flatness array

To set up the sweeper

Connect the equipment as shown in Figure 5-l. Do not connect the power

1.
sensor to the system yet. Press

If a frequency range other than the full range of the instrument is desired,

2.
use the

If external cables and/or devices are used between the sweeper leveling

3.

CSTART)

and

m

point (the RF OUTPUT if internally leveled, or the coupler/splitter output
if externally leveled) and the remote test port, the nominal (average) loss

of these components should be entered as an offset. To enter the power

offset, press

nominal loss from the leveling point of the sweeper to the test port. (For

(SHIFT)

OFFSET (in the POWER key group) and then enter the

example, if there is a 6 dB loss from the leveling point to the remote test
port, enter a power offset of +6

(PRESET)

on the sweeper.

keys to input the desired frequency range.

dB.)

Set the power level to the level desired at the test

4.

[POWER LEVEL) and entering the desired number.

5.

Select

[ml

SPECIAL

112) (jj).

Use the @j @J keys to select

the type of power meter you will be using.

6.

Select (SHIFT) SPECIAL

113) (w’.

Enter the HP-IB address of the

(437B

purt

by pressing,

for this example.)

power meter you will be using for the calibration. (Thirteen is the default
address for power meters.)

7.

Press

[%iW)

a. Select whether to calibrate over

FLTNESS

CAL

S?.at-:~t,op

(correction points will be

linearly spaced over the selected Start/Stop frequency range, or Fu 11

Bard (correction points will be linearly spaced over the full frequency

range of the instrument). Use the m Q) keys to make your selection,
then press [Hz/s/ENTER).

b. Select the number of correction points, using the keypad for your entry

(valid entries range from 2 to Sol), then press

I-1.

c. The MARKER/SWEEP/STATUS display should now read:

Conned.

437B PM

--

EHTER.

5-4

Creating User Flatness Arrays

Creating a user flatness array

To set up the power meter

l Zero and calibrate the power meter/sensor.
l Enter the appropriate power sensor calibration factors into the power

meter.

l Enable the power meter/sensor

on the HP

l Connect the power sensor to the point where corrected

437B

power meter refer to its operating and service manual.

cal

factor array. For operating information

power

is desired.

(See Figure 5- 1.)

To start the user flatness cal

l

The MARKER/SWEEP/STATUS display should still read:

C:onnect. 437B

l Press

(Hz/s/ENTEji)

correction point’s frequency and power as it is measured.

l When the calibration is finished, the flatness correction is automatically

turned on, and the FLTNESS ON LED annunciator is lit on the front panel

of the sweeper. Power correction will be linearly interpolated between the
measured correction points. The POWER display will
port power.

PM -- ENTER.

to start the calibration. The display will show each

now.show

the test

Attention!

Before doing anything else, save this calibration in one of the instrument’s registers. If the calibration

has not been saved, and the instrument is preset, a register is recalled, or the power offset is
changed, the calibration will be lost. To save the calibration, press
of the instrument register you wish to save it in.

ISAVE)

and then enter the number

5-5

Creating User Flatness Arrays

Creating a user flatness array for use in a scalar analysis measurement

To set up the sweeper

1. Connect equipment as shown in Figure 5-2. Do not connect the power
sensor to the system yet.

2. Press (PRESET) on the scalar analyzer (HP 8757).

3. If a frequency range other than the full range of the instrument is desired,
use the

frequency range.

4. If external cables and/or devices are used between the sweeper leveling
point (the RF OUTPUT if interrmlly leveled, or the coupler/splitter output
if externally leveled) and the remote test port, the nominal (average) loss

of these components should be entered as an offset. To enter the power

offset, press
nominal loss from the leveling point of the sweeper to the test port. (For

example, if there is a 6 dB loss from the leveling point to the remote test

port, enter a power offset of +6

m

and

@iYWj

CsTopl

keys on the sweeper to input the desired

OFFSET (in the POWER key group) and then enter the

dB.)

5. Set the power level to the level desired at the tat port by pressing

(POWER LEVEL] and entering the desired number.

6.

Select

7.

Select (SHIFT)

@iiF]

SPECIAL (12)

(HZ/S/ENTER_).

Use the

the type of power meter you will be using.

SPECfAL @

(Hz/s/ENTER_). Enter the

Q) @Jj

(437B

for this example.)

HP-R3

keys to select

address of the
power meter you will be using for the calibration. (Thirteen is the default
address for power meters.)

To set up the analyzer

1. On the analyzer, set up the appropriate measurement (i.e. gain for an
amplifier). Calibrate the measurement (thru and short/open calibration).
Press

m

(iJ on the analyzer to store the analyzer configuration and

sweeper parameters in storage register 1.

5-7

Creating User Flatness Arrays

Creating a user flatness array for use in a scalar analysis measurement

Attention!

Do not proceed until the HP 8757 system interface is turned off by pressing
pressing softkeys, MORE,

SWEZP

MODE, and

SYSIElTF

ON

@FiiZ].

OFF

on the analyzer.

Then by

To set up the power meter

1. Zero and calibrate the power meter/sensor.

2. Enter the appropriate power sensor calibration factors into the power
meter.

3. Enable the power meter/sensor cal factor array. For operating information

on the HP

4. Connect the power sensor to the point where corrected power is desired.
(See Figure 5-2.)

437B

power meter refer to its operating and service manual.

I

To start the user flatness cal

1. On the sweeper, press
a. Select whether to calibrate over St>arSt.op (correction points will be

linearly spaced over the selected Start/Stop frequency range, or

Band

(correction points will be linearly spaced over the full frequency

range of the instrument). Use the @)

then press (Hz/s/ENTER).

5-8

m

FLTMESS

CAL

(JJ

keys to make your selection,

FIJ

11

Creating User Flatness Arrays

b. Select the number of correction points, using the keypad for your entry.

Valid entries range from 2 to 801, then press

CH+./ENTER).

c. The MARKER/SWEEP/STATUS display should now read:

Connel:t.

437E:

PM --

Et,ITER.

2. Press

CHZ/S/ENTER)

to start the calibration. The display will show each

correction point’s frequency and power as it is measured.

3. When the calibration is finished, the flatness correction is automatically
turned on, and the FLTNESS ON LED annunciator is lit on the front panel
of the sweeper. Power correction will be linearly interpolated between the

measured correction points.

4. Save the calibration by pressing

Attention!

If the calibration is not saved in an instrument register, and the sweeper or analyzer is preset, a

register is recalled, or the power offset is changed, the calibration will be lost. Reactivating the
SYSINTF on the analyzer will also cause a preset and loss of the calibration. Be sure to save the
calibration as described in the previous step before continuing.

CsAVEJ

(iJ on the sweeper.

To reactivate the HP 8757 system interface

1.

Press the softkey SYSINTF OH OFF on the analyzer and the sweeper will

preset.

2. Press

3. Devices can now be tested.

(RECALL_)

(iJ to pull up the calibration.

5-9

6

Operating a Master/Slave

Setup

Operating a Master/Slave Setup

Two HP 83750 series sweepers can be configured for two-tone measurement
capabilities. Two synchronously tracking sweepers can be configured as a

“master/slave” pair for mixer characterization or inter-modulation distortion

measurements. The swept frequency accuracy allows control of the sweepers

at Exed- or swept-frequency offsets.
To implement master/slave operation, configure the sweepers as shown in

Figure 6-l. The master sweeper generates the 10 MHz frequency reference
for both sources. The source synchronization cable (HP part no. 83750-60059)

must be connected between the auxiliary interface connectors on the rear

panels of the sweepers.

When conEguring a two-tone measurement system, the slave does not need
to interface with any instruments other than the master. The master should
interface with the display device (scalar analyzer or oscilloscope, for example)

as if it were a stand-alone sweeper.

6-2

SOURCE
SYNCHRO­NIZATION
CABLE

AUXILIARY

INTERFACE

:

I
I

Operating a Master/Slave Setup

-----------.e---

10 MHz
REF OUT

pg424ab

Figure

“SLAVE”

SYNTHESIZED

SWEEPER

6-l.

Master/Slave Setup

AUXILIARY

INTERFACE

10 MHz
REF IN

6-3

Tb set up the master sweeper

1. Press

2. Activate the master mode by pressing

(jPRESETJ.

If the display does not read

[M)

13-A rlMsde=MHSTER,

(SPECIAL)

then press the

(19) C-1.

m

once to set the control mode to master.

3. Set the desired frequencies by using the

(CJV(SPAN)

NOTE

It is recommended that the master and slave sweepers frequencies not differ more than 5
point in the sweep. If this requirement is not met, it is possible for unlocks to occur. If frequency
offsets greater than 5
unlocks.

keys, or the

GHz

are required, it may be necessary to reduce the sweep speeds to eliminate

Icw]

key.

CSTARTY(STOP_)

keys, the

GHz

4. Set the desired power level using the (POWER LEVEL] key.

For swept measurements.

5. Set the desired sweep time using the (TIME) key. (The recommended
minimum sweep time for master/slave mode is 100 ms.)

key

at any

NOTE

The master and slave sweepers must have identical sweep times. Therefore, the value entered here

must also be entered into the slave sweeper.

6-4

Operating a Master/Slave Setup

To set up the master sweeper

For stepped measurements.

6.

Set the sweep mode to stepped by pressing

then pressing the @) key until the display reads:

7.

Set the number of points by pressing

@iE)

(GiF]

SWEEP MODE $ , and

Si>Jeep= St. ep lzt:tr,t.

POINTS and entering the

desired number of points.

NOTE

The master and slave sweepers must have identical sweep mode, number of points, and sweep time

settings. Therefore, the values entered here must also be entered into the slave sweeper.

.

6-5

31 set up the slave sweeper

1. Press (PRESET).

2. Activate the slave mode by pressing (SHIFT)
Press the @) key until the display reads

3. Set the desired frequencies by using the

(EEiK] 119) (-1.

Cnt.

t- 1

Mode=SLHVE.

(START)/0

keys, the

@J(SPAN) keys, or the ccw) key.

NOTE

It is recommended that the master and slave sweepers frequencies not differ more than 5
point in the sweep. If this requirement is not met, it is possible for unlocks to occur. If frequency
offsets greater than 5
unlocks.

4. Set the desired power level using the

For

swept measurements.

GHz

are required, it may be necessary to reduce the sweep speeds to eliminate

POWER

LEVEL] key.

GHz

at any

5. Set the sweep time to the same value as the master sweeper using the

m

key. (The recommended minimum sweep time for master/slave

mode is 100 ms.)

For stepped measurements.

6.

Set the sweep mode to stepped by pressing (SHIFT)

then pressing the @) key until the display reads:

SWEEP

MODE $ , and

Sweep= St. ep

C:ont..

7. Set the number of points to the same value as the master sweeper by
pressing

6-6

(SHIFTI)

POINTS and entering the number of points.

See also

For a

pinout

description of the source synchronization cable, see the

“Multi-pin Connectors” section of Chapter 7, “Front/Rear Panel.”

6-7

7

I

-

-

Front/Rear Panel

Front/Rear Panel

This chapter contains detailed information on various aspects of the sweeper

front and rear panel. Information on the following can be found in this

chapter:

0

Connectors

l Display
l HP-B Lang/Address Switch
l Knob
l Line Power Switch
l Power Cables

7-2

Connectors

pg412ab

00
00
00

.-I
0 ::

0
0

a

0 0

-

LJLJ 00 00 00 0 0 0

@

@@”

I \

SWEEP OUT

Figure 7-1. Sweeper Connectors - Front Panel

ALC IN

‘El0000

00000

moooo

l30000

Cl

0

0

la

Q @I

L

RF

,

\

\/

OUTPUT

7-3

(OPT

RF

OUTPUT

(OPT lE4 ONLY)

Front/Rear Panel

Connectors

SOURCE MODULE

I NTERFACE

1EE

ONLY)

I

SWEEP

OUTPUT

Z AXIS

BLANK/MKRS

I

STOP

SWEEP

PULSE

I N/OUT

FM INPUT

AUX

I NTE

I

LIARY

DIARY

:RFACE:RFACE

HP-IB

HPllB

VOLTi/GHz

VOLTS/GHz

7-4

A’M

AM

OUTPUTOUTPUT

INPUTINPUT

TRIGGER TRIGGERTRIGGER TRIGGER

OUTPUTOUTPUT

Figure 7-2. Sweeper Connectors - Rear Panel

INPUTINPUT

1OilHz

1OMHz

REF

REF

OUT

OUT

1OivlHz

1OMHz

REF

REF

IN

IN

pg413ab

BNC Connectors

Front/Rear Panel

Connectors

10 MHz REF IN

10 MHz REF

OUT

ALC IN

AM INPUT

FM

INPUT

This rear panel female BNC connector accepts a -5 to + 10

dBm

signal from an external time base reference which is
within
MHz. The nominal input impedance is 50
detects when a valid reference signal is connected to it and
automatically switches from internal to external reference
operation.

This rear panel female BNC connector provides a nominal

signal level of 0
accuracy is determined by the tune base used.

This front panel female BNC connector is used for external
power meter leveling or external negative detector leveling.
The damage level is

This rear panel female BNC connector accepts the amplitude
modulating signal input when External AM is enabled. The
nominal input impedance is 3.5

f15

This rear panel female BNC connector accepts the frequency
modulating signal input when DC or AC FM is enabled. The
nominal input impedance is 1

f15

100

kQ.

v.

v.

510

ppm of 10 MHz or any sub-multiple down to 1

61.

This connector

dBm,

and output impedance of 50 0. The

f15 V.

The nominal input impedance is

kQ.

The damage level is

k62.

The damage level is

PULSE IN/OUT

This rear panel female BNC connector can be used as
either an external pulse input or output for internal pulse
modulation. In either case, it is TTL level compatible and
has a nominal impedance of 5

2 +lOVor< -5V.

A TTL high level (> +2 V) enables the selected power level
to be at the RF OUTPUT connector, while a TTL low level
turns the RF off.

khl.

The damage level is

7-5

Front/Rear Panel

Connectors

STOP SWEEP

SWEEP OUT

TRIGGER
INPUT

This rear panel female BNC connector causes a sweep to be
stopped when this input is pulled low. Retrace does not

occur, and the sweep resumes when this input is pulled
high. The open circuit voltage is TTL high and is internally
pulled low when the instrument stops its sweep. The
damage level is 2 + 10 V or 5 -4

V.

These front and rear panel female BNC connectors provide
a voltage range of 0 to + 10 V. When the instrument is
sweeping, the SWEEP OUT ranges from 0 V at the beginning
of the sweep and + 10 V at the end of the sweep regardless
of the sweep width. In CW mode, the SWEEP OUT ranges
from 0 V at the sweeper minimum frequency to + 10 V
at the specifled maximum frequency, with a proportional
voltage for frequencies between the specified minimum and

maximum. When the sweeper is in manual sweep operation,

the SWEEP OUT voltage is a percentage of the span. The
nominal output impedance is 100

f0.05%, f5 mV

When used with the HP

into a high impedance load.

8757D

61.

The typical accuracy is

scalar analyzer in

ramp-sweep mode, the rear panel output is a series of 0 to

+ 10 V pulses similar to the Trigger Output.

This rear panel female BNC input is activated on a TTL

rising edge. It is used to externally initiate an analog sweep

or to advance to the next point in stepped sweep mode. The

damage level is 2 + 10 V or 2 -4

V.

TRIGGER
OUTPUT

VOLTS/GHz

OUTPUT

7-6

This rear panel female BNC connector outputs a 1

,ns

wide

negative-going TTL pulse at 1601 points evenly spaced

across an analog sweep, or at each point in stepped sweep

mode. When used with the HP

8757D

scalar analyzers, the
number of pulses per sweep (in analog sweep mode) is
determined by the number of HP 8757 trace points.

This rear panel female BNC connector supplies a voltage
that is proportional to the RF output frequency, which can
be configured to any desired sensitivity and offset within

a

f12

V range. The default setting is 0.5

minimum load impedance is 2

3~0.1% f10

mV

kbl.

The typical accuracy is

V/GHz.

The

Z

AXIS

BLANK/MKRS

Front/Rear Panel

Connectors

This rear panel female BNC connector supplies a positive

rectangular pulse (approximately +5 V into 2

kfl)

during

the retrace and band switch of the RF output when the

instrument is sweeping. This output also supplies a -5

V pulse when the RF output is coincident with a marker

frequency.

7-7

Front/Rear Panel

Connectors

Multi-pin Connectors

AUXILIARY INTERFACE This connector provides special control signals used in master/slave interface

operation with another source, and in other special-purpose applications. This

connector is a

25-pin

D-subminiature receptacle located on the rear panel.

AUXILIARY INTERFACE

SOURCE SYNCHRONIZATION

(HP P.N. 8375040059)

Figure 7-3. Auxiliary Interface Connector

CABLE

7-8

Table 7-1. Pin Description of the Auxiliary Interface

Pin

#

1

2 Z-Axis Blanking/Markers out

3
4
5
6

1

8
9
10 Rear Panel Control 1
11
12
13
14 Low Marker out
15
16
17 Rear Panel Control 2
18
19 Digital Ground
20 No Connection
21
22 No Connection
23 low Source Settled
24
25

*

Or 0 to 10 V pulses when used with a HP 87570 scalar analyzer.

Alternate Sweep Out out

Spare
Rear Panel Control 3
low Stop Sweep

+5.2

v out
Digital Ground
Low Divider-Sync
External Trigger

Rear Panel Control 0

low

Retrace

Alternate Sweep In

Low

Clualified

Stop Sweep

Rear Panel Control 4

Sweep Output

No Connection

low Source Settled

Spare

Function

In/Out Signal

In

I/O TTL
I/O

TTL

I/O TTL

In

I/O TTL
I/O TTL
I/O

TTL

In

out
out TTL

I/O

TTL

out

In TTL
out
out

Front/Rear Panel

level

TTL

Blank- +5 V
Marker- -5 V

f12

v

+5.2

v

Gnd

TTL

TTL
TTL
rr!

0

to 10 V ramp”

Gnd

TTL
f12

v

Connectors

7-9

Front/Rear Panel

Connectors

HP-II

This connector allows the sweeper to be connected to other instruments or
devices on the interface bus. Details of this cable are shown in Figure 7-4.

HP

table following the figure.

HP-IE

SHl

AH1

TE

LELo4
SRl

RL 1

PPO

DC1

COl-3, 28

DC1

El

part numbers for various HPIB cables that are available are shown in the

-07

24 :: 12

::
::
::
::

13 ::

4

1

0

pg415ob

Figure 7-4. HP-IB Connector and Cable

HP-IB Interface Cables Available

7-10

Front/Rear Panel

Connectors

As many as 14 HP-B instruments can be connected to the sweeper (15
total instruments in the system). The cables can be interconnected in a star
pattern (one central instrument with the

HP-lB

cables emanating from that
instrument like spokes on a wheel), or in a linear pattern (like boxcars on a
train), or a combination of the two. There are certain restrictions that must
be followed when interconnecting instruments:

l Each instrument must have a unique HP-B address, ranging from 0 to 30

(decimal). Refer to

“BDDRESS ’

in the “Instrument State Keys” chapter for information on

“HP-IB

Lang/Address Switch” later in this chapter, or

setting the sweeper HP-B address.

l In a two-instrument system that uses just one HP-B cable, the cable length

must not exceed 4 meters (13.2

l When more than two instruments are connected on the bus, the cable

ft).

length to each instrument must not exceed two meters (6.6 ft).

l The total cable length between all instruments must not exceed 20 meters

(65 ft).

Hewlett-Packard manufactures HPIB extender instruments (Models HP

37201A

and HP

37204AiB)

that overcome the range limitations unposed by
the cabling rules. These extenders allow twin pair cable operation up to 1 km
(3,280
service offices can provide additional information on the

ft),

and telephone modem operation over any distance. HP sales and

HP-IB

extenders.

7-11

Front/Rear Panel

Connectors

The codes next to the
the HP-IB electrical capabilities of the synthesizer, using IEEE Std. 488-1978
mnemonics (HP-IB, GP-IB,

equivalent). Briefly, the mnemonics translate as follows:

SHl Source Handshake, complete capability.
AH1
T6:

TEO

L4

LEO

SRl Service Request, complete capability.
RLl

PPO
DC1
DTl

CO, 1, 2, 3, 28

HP-II3

connector, illustrated in Figure 7-4, describe

IEEE-488,

Acceptor Handshake, complete capability.
Talker; capable of basic talker, serial poll, and unaddress if

MLA.

l%Iker,

Extended address; no capability.

Listener, capable of basic listener, and unaddress if MTA.

Listener, Extended address; no capability.

Remote Local, complete capability.
Parallel Poll, no capability.
Device Clear, complete capability.
Device Trigger, complete capability.

Controller capability options; CO, no capabilities; Cl, system
controller;

C28,

C2,

send I. F. messages.

and RX-625 are all electrically

send IFC and take charge;

C3,

send REN;

El
These codes are described completely in the IEEE Standard 488 (1978)

IEEE Standard Digital Interface

identical ANSI Standard MCl. 1.

7-12

Electrical specihcation indicating open collector outputs.

for

Programmable Instrumentation

or the

Front/Rear Panel

Connectors

SOURCE MOOULE This connector sends and receives digital and analog signals to and from an
INTERFACE
Only)

(Option 1EE

HP 83550Series millimeter-wave source module. With the source module
connected, the sweeper assumes the characteristics of the source module.

MOD

MOD

MOD Cl

DIG GND

Dl

f5V

EXT LVL (COAX)

RESERVED5

-15v

V/GHz

Figure 7-5. Interface Signals of the Source Module Connector

The codes indicated in Figure 7-5 translate as follows:
MOD DO

Source module data line zero. Signals MOD DO through
MOD D3 are the millimeter source module data bus lines
(bidirectional).

MOD

Dl

Data line one.

RTN

SENSE

RESERVED

pg416ot

MOD D2
MOD D3
MOD CO

MOD Cl

Data line two.
Data line three.

Source module control line zero. Signals MOD CO and MOD

Cl are the control lines for the read/write to and from the
millimeter source module.

Control line one.

7-13

Front/Rear Panel

Connectors

MOD SENSE

Source module sense. A 1 mA current is injected on this line

by the millimeter source module to indicate its presence.

This signal always equals 0 V.
L MOD RF OFF
EXT

LVL

RET

EXT LVL

Low = RF off. Source module RF is turned off.

Source module external leveling return.

Source module external leveling input, from the millimeter

source module.

0.5V/GHz

-15v

Internal
Power supply. Range is -14.25 to -15.45 V.

0.5V/GHz

to the millimeter source module.

(See note below.)

+15v

Power supply. Range is + 14.25 to + 15.45 V.
(See note below.)

+8V

+5v

NOTE
The values for the four power supplies above are valid when a millimeter head is connected. With no

load on the connector, the values would be:

Power supply. Range is +7.50 to +8.45 V. (See note below.)
Power supply. Range is

+4.75

to +5.40 V. (See note below.)

-

15 v supply:
+ 15 v supply:
+ 8 v supply:
+ 5 v supply:

DIG GND

.5

V/GHz

RTN 0.5

ANLG GND
RET

7-14

-14.4 to -15.45 v

+14.4

v to

+15.45

v

+7.75

v to

+a.45

v

+4.75

v to

+5.40

v

Digital ground.

V/GHz

return.

Analog ground return.

Front/Rear Panel

Connectors

RF Output Connector

The standard front panel RF OUTPUT connector is a precision 3.5 mm male
connector. When Option
ruggedized Type-N connector. The nominal source impedance is 50

When making connections to this connector, carefully align the center
conductor elements, then rotate the knurled barrel while mating components
remain still. Tighten the barrel until Iirm contact is made.

lkke

care when working with this connector. If the connector is mechanically

degraded in any way, high frequency losses can occur. Refer to application
note 326, Coaxial
number

5954-

Sz/stems -

1566) for more information.

1ED

is installed, this front panel connector is a

Principles of Microwave Connector Care

61.

(HP

part

7-15

Display

The sweeper front panel display contains two areas (Frequency, and
Marker/Sweep/Status and Power) for displaying the current operating
parameters of the sweeper. Front panel annunciators show the status of
several of the sweeper functions and settings.

FREQUENCY DISPLAY

MARKER/SWEEP/STATUS

DISPLAY

Figure 7-6. Sweeper Display

POWER DISPLAY

pg410pb

7-16

Front/Rear Panel

Display

Frequency Display

The left-hand display is labelled FREQUENCY and is used exclusively to
show information about frequencies being generated. (Information about
markers is not pertinent to generated frequencies and is not displayed here.)

In Start/Stop and CF/Span sweep modes, the left display has two separate
fields of 11 characters each, whose contents depend on the instrument mode.
Two blank spaces separate the two fields. Frequencies are displayed using
eight signihcant digits, followed by a three-character frequency unit
MHz, or

GHz).

The decimal multiplier is changed automatically to keep the
number being displayed in the range of 1 to 999.99999, and digits below 1

kHz

resolution are not shown. Leading zeros are suppressed.

In CW mode, there is one 24-character field. Frequencies are displayed using
up to 11 significant digits, followed by a three-character frequency unit
MHz, or

GHz).

The decimal multiplier is changed automatically to keep the
number being displayed in the range of 1 to 999.99999, and digits below 1 Hz
resolution are not shown. Leading zeros are suppressed.

(kHz,

@Hz,

NOTE

The decimal separator (either .
to the “Special Functions” chapter for more information.

or , I can be changed by selecting Special function number 18. Refer

7-17

Front/Rear Panel

Display

Marker/Sweep/Status and Power Display

The right-hand display is divided into two fields, although there is no physical
separation between them. (Normally, one blank space is inserted between

the left and right Eelds. When some features are accessed, however, all 24

characters of the right display can be used.)

The left Eeld is labelled MARKER/SWEEP/STATUS, and is used to show a
variety of information including marker frequencies, sweep time, and general
instrument status. Sixteen characters are reserved for this Eeld, including any
units displayed.

The right Eeld is labelled POWER, and displays the power level in

dBm.

seven character cells wide. Exed format.

NOTE

When operating the sweeper in a secure environment, the display can be blanked so that the sweeper

parameters and status cannot be viewed. For more information, refer to the “Special Functions”
chapter of this manual.

It is

I

7-18

Annunciators

DISPLAY

ANNUNCIATORS

Front/Rear Panel

Display

LED

ANNUNCIATORS

Figure 7-7. Sweeper Display and LED Annunciators

The front panel annunciators show the status of several of the sweeper

functions and settings. Refer to Figure 7-7. Notice that there are two types of

annunciators: display and LED.

A display annunciator is not visible if its associated function is not active or
selected. For example, if external pulse modulation is currently selected, the

EXTMOD annunciator will be lit, otherwise, it will not be visible.

The display annunciators that will appear in the left-hand (frequency)
display are SHIFT, START, CF, CW, MAN, SWEEP, EXT REF, ALT, STOP,

SPAN, MULT, and OFFSET. The display annunciators that will appear in

the right-hand (marker/sweep/status and power) display are MSG, MKRS,

EXTMOD, INTMOD, UNLOCK, STEP, UNCPLD, EXT ALC, PWR SWP,

SLOPE, UNLEV, and RF OFF.

7-19

Front/Rear Panel

Display

The front panel LED annunciators (R, L, T, S, MKR A, Ml-+M2 SWP,
UNLOCKED FM, and FLTNESS ON) will be lit to show you that an
associated condition exists.

An explanation of each annunciator follows.

Display

Annunciators

SHIFT

This annunciator appears when
goes off when any other key is pressed (or when

(ml

is pressed, and

m

pressed again).

is

START

CF

cw

MAN

SWEEP

EXT REF

ALT

STOP

SPAN

This annunciator appears when
and goes off when Icw),

This annunciator appears when
and turns off when Icw),

This annunciator appears when
off when a,

@Gi), (START),

(START)

ICF),

or

(ZJ

(START),

or

or [STOP) is pressed,

m

is pressed.

or

m

is pressed,

or

ISTOP)

is pressed.

Icw_l

is pressed, and turns

ISTOP)

is pressed.

This annunciator indicates that manual sweep mode has
been selected.

This annunciator indicates that the instrument is performing
a sweep. This annunciator appears only while the
instrument actually sweeps, not while it waits for a trigger
signal (even though it is in sweep mode). In continuous
sweep mode, the annunciator will blink with slow sweeps,

but remain on with fast sweeps.

This annunciator indicates that an external frequency
reference is in use.

This annunciator indicates that the alternate sweep mode is
active.

This annunciator appears when
and turns off when Icw), a, or

This annunciator appears when
turns off when Icw], (START), or

(VZ??i]

ISPAN)

LCF)

or

m

or

~

is pressed.

m

is pressed and

is pressed.

is pressed

MLJLT

7-20

This annunciator indicates that the displayed frequency is a
multiple of the actual RF output frequency.

Front/Rear Panel

Display

OFFSET

MSG

MKRS

EXTMOD

INTMOD

UNLOCK

STEP

UNCPLD

This annunciator indicates that the displayed frequency is
offset from the actual RF output frequency.

This annunciator indicates that the sweeper has a new
message that has not been displayed, such as an error
message or instrument failure message. Messages are viewed
by pressing the front panel

CMsGl

key.

This annunciator appears when any of the markers (0 to 9)

are on.

This annunciator appears under any of the following

conditions:

l AM Mode = External

l FM Mode = AC/Locked

l Pulse Mode = External

or

DC/Unlocked

This annunciator appears if Pulse Mode is set to Internal,

Scalar, or 1

kHz

square-wave.

This annunciator appears when any of the internal
synthesizer loops are unlocked.

This annunciator indicates that the Sweep Mode is set to

Stepped Sweep.
This annunciator indicates that automatic coupling between

the attenuator and the ALC reference level is turned off in
the Special area. (For Option

1El

instruments only). This
mode is automatically selected whenever the ALC mode is
not in internal mode or unleveled mode.

EXT ALC

PWR SWP

SLOPE

UNLEV

RF OFF

This annunciator indicates that the ALC mode is set to
either Diode or Power meter.

This annunciator indicates that the Power Sweep function is

active.

This annunciator indicates that the Power Slope function is
active.

This annunciator indicates that the source is unable to
maintain the correct output power level for the current

output frequency, or that the ALC is turned off.

This annunciator indicates that the RF output is turned off.

7-21

Front/Rear Panel

Display

LED
Annunciators

R

This LED annunciator is lit when the sweeper is in remote

HP-II3

operation.

L

This LED annunciator is lit when the sweeper is receiving
information or commands over HP-IB.

T

This LED annunciator is lit when the sweeper is transmitting
information over HP-IB.

S

MKR A

Ml-M2 SWF’

This LED annunciator is lit when the sweeper is receiving

an

SRQ over HP-IB.
This LED annunciator is lit if the marker delta mode is on.
This LED annunciator is lit when

(MI+MP

SWEEP) is pressed.

UNLOCKED FM This LED annunciator is lit if the FM mode is set to

DC/Unlocked.

FLTNESS ON

This LED annunciator is lit if a power flatness correction
array is enabled.

7-22

HP-IB Lang/Address Switch

The HP-IR switch on the rear panel is used to select the sweeper language
and

HP-II!

address when you apply AC power. These parameters can also be

selected via front panel operation.
Refer to Figure 7-8 for a pictorial explanation of the various switch settings

for the HP-IB address of the sweeper. The selected address depicted in this
figure represents an HP-IR address of 19.

When the HP-IR portion of the switch (switch positions 1 through 5) are all
set to 1, any address changes made from the front panel are retained through
a power cycle of the instrument. If you want your sweeper to default to a
particular address at power up, set the switch to the desired. address; you can
still make changes from the front panel, but they won’t be retained through a

power cycle.

Refer to Figure 7-9 for a pictorial explanation of the switch settings for
instrument language.

Refer to Figure 7-10 for a pictorial explanation of how to set the switch for
clearing the register contents at power on.

SELECTED

POSITION

ADDRESS

ADDRESS-

ADDS 1 TO ADDRESS IF SELECTED POSITION =
ADDS 2 TO ADDRESS IF SELECTED POSITION =
ADDS 4 TO ADDRESS IF SELECTED POSITION =
ADDS 8 TO ADDRESS IF SELECTED POSITION =
ADDS 16 TO ADDRESS IF SELECTED POSITION =

Figure 7-8. HP-IB Address Switch Settings

1
1
1
1

1

7-23

Front/Rear Panel

HP-18

Lang/Address Switch

= SCPI

1

I I=!

0

1

0

Figure 7-9. Instrument language Switch Settings

=

Register Contents Are

Through An AC Power Cycle.

1

1 I=!

0

(111;

1

=

Register Contents Are Cleared

Through An AC Power Cycle.

Saved

7-24

Figure

7-l

0. Clear Register Contents Settings

See Also

Front/Rear Panel

HP-IB Lang/Address Switch

“Instrument

State Keys” panel of the sweeper.

“

Special

Functions”

For information on setting the

For information on setting the language from the front panel
of the sweeper.

HP-IB

address from the front

7-25

Knob

The front panel knob is used to increase or decrease parameter values.
Pointers ( WV ) over a parameter or numeric value in the display indicate
that the function is active and its value will be increased or decreased when
knob is rotated.

The front panel knob is used to give an analog feel to the setting of the
values. Any of the values that can be set through the numeric entry pad, or
the step keys, can also be set using the knob. However, the rate at which the
active parameter varies, for a given amount of knob rotation, is dependent on
the parameter that is being controlled.

If ENTRY OFF
disappear from the display and rotating the knob will have no affect on the
sweeper parameters until another function key is pressed.

(m

[H

Z/S/ENTER

)

has been enabled, the pointers will

Equivalent SCPI Commands

The equivalent SCPI commands for knob rotation are SYST : KEY 6 1 which
simulates clockwise knob rotation, and SYST:KEY 62 which simulates
counterclockwise knob rotation.

7-26

Line POWER Switch

P

INSTRUMENT STATE

7m

SHIFT

PRESET MODE

1

/

PRESETI

II

I--

II I

c

c

STANDBY LINE POWER SWITCH

pg49ab

Figure

7-l

1. The Sweeper line POWER Switch

The line POWER switch turns power to the sweeper to either on or standby.
The sweeper line POWER switch is located at the bottom left corner of the

front panel. Pressing the switch so that the button locks in the “in” position
turns the sweeper on and pressing the switch again so that it is in the “out”
position turns it to standby. When set to standby, most of the sweeper
circuitry is powered off, however, power to the internal timebase (Option

lE5) is not disconnected.

When the sweeper is on, the green LED indicator will be illuminated. When
the sweeper is in standby, the amber LED indicator will be illuminated.

7-27

Front/Rear Panel

line POWER Switch

WARNING

Before turning the sweeper on, make sure that it is grounded through
the protective conductor of the power cable to a mains power receptacle
provided with protective earth contact. Any interruption of the
protective grounding conductor inside or outside of the sweeper or
disconnection of the protective earth terminal can result in personal

injury.

7-28

Power Cables

The line power cable is supplied in one of several configurations, depending
on the destination of the original shipment.

Each instrument is equipped with a three-wire power cable. When connected

to an appropriate AC power receptacle, this cable grounds the instrument

chassis. The type of power cable shipped with each instrument depends on
the country of destination. See Figure 7-12, “Power Cable and Line (Mains)
Plug Part Numbers”, for the part numbers of these power cables. Cables
are available in different lengths and some with right-angle plugs to the
instrument. Check with your nearest Hewlett-Packard service center for
descriptions and part numbers for these cables.

NOTE

There is no line voltage selector switch on the instrument. The line module will automatically switch
between 110 and 220 Vat as needed.

7-29

FrontlRear Panel

PLUG TYPE * *

250V

250V

25DV

125V

250V

$;AT

NUMBER

8120-1351

8120-1703 90’

8120-1369

8 120-0696

8120-1689
8120-1692

8120-1348 Straight*

8120-1538

8120-1378

8120-4753 Straight

8120-1521

8120-4754 90’

8120-5182

8120-5181

90’

DESCRIPTION LENGTH COLOR

Straight*

Straight*

90-

Straight*

90’

Straight”

90’

Straight*

90’

PLUG

BS1363A

NZSS196/ASC112

CEE7-Yll

NEMAS-15P

NEMAS-15P

NEMA5-15P

CABLE

ct.4 (INCHES)

229 (90) Mint Gray
229 (90) Mint Gray Cyprus, Nigeria

201 (79)

221 (87)

201 (79)

201 (79) Mint Gray

203 (80) Block
203

(80)

203 (80)
230 (90)
203 (80)

230 (90)

200 (78)

200 (78)

CABLE

Gray

Gray

Mint Gray

Black

Jade Gray 200 v), Bra2 II,

Jade Gray

Jade Gray
Jade

Gray

Jade

Gray

Jade Gray

FOR USE

IN COUNTRY

Great Britain.

Singapore,

Zimbabwe

Argentina,
Australia.
New Zealand,

Mainland China

East and West

Europe’

African Republic
United Arab
Republic

(unpclorized

many nat
United States

Canada,

Japan (100 V or

Colombia,

Philippines,

Saudia Arabia.

Taiwan

Central

Ions)

Israel

in

Mexico

*

Part number for plug 1s industry identifier for plug only. Number shown for cable

HP Part Number for complete cable.

**

E = Earth Ground; L = Line; N = Neutral.

lncludlng

plug.

Figure 7-12. Power Cable and line (Mains) Plug Part Numbers

7-30

i

8

Instrument State Keys