Installation and Operating Instructions
Aga Bottom Mount Refrigerators
Aga-Heartland 1050 Fountain St. North, Cambridge, ON, N3H 4R7
Phone 877-650-5775 Fax 877-650-3773
Model:
AFHR-36
36” Bottom Mount Refrigerator
Save these instructions
for future use
Keep sales receipt and/or cancelled check as proof of purchase. If service is required, have complete model and serial
number identification of your refrigerator. This is located on a data plate inside the refrigerator compartment, on the upper
left side. Record these numbers below for easy access :
Model Number __________________________________ Serial Number____________________________________
Date of Purchase________________________________
In our continuing effort to improve the quality and performance
of our appliances, it may be necessary to make changes to the
appliance without revising this guide.
Note: Please read these instructions thoroughly before attempting to instsall this unit.
ATTENTION INSTALLER: Leave this manual with appliance#37311.090707
Important Safety Instruction.............................................................................................3
What You Need to Know About Safety Instructions..................................................3
Recognize Safety Symbols, Words, Labels..............................................................3
Power Cord...............................................................................................................3
Installation..........................................................................................................................5
Measuring the Opening.............................................................................................5
Leveling (all models)..........................................................................................................6
Transporting Your Refrigerator.........................................................................................7
Connecting the Water Supply...........................................................................................7
Materials Needed......................................................................................................7
Touch Temperature Controls............................................................................................8
Fresh Food Features..........................................................................................................9
Shelves......................................................................................................................9
Dairy Center..............................................................................................................9
Door Buckets.............................................................................................................9
Full-width Door Shelf.................................................................................................9
Model Diagrams ..............................................................................................................10
Beverage Chiller™..................................................................................................11
Crisper Drawer.........................................................................................................11
Temperature-Controlled Drawer..............................................................................11
Grip Pads................................................................................................................12
Beverage Organizer™............................................................................................12
Freezer Features..............................................................................................................13
Lower Wire Basket..................................................................................................13
Upper Wire Basket..................................................................................................13
Ice and Water..........................................................................................................13
Automatic Ice Maker................................................................................................13
Water Dispenser .....................................................................................................14
Water Filter .............................................................................................................15
Food Storage Tips............................................................................................................16
Fresh Food Storage................................................................................................16
Frozen Food Storage..............................................................................................16
Food Storage Chart ................................................................................................17
Care and Cleaning............................................................................................................19
Cleaning the Outside...............................................................................................20
Removing Odors From Refrigerator........................................................................20
Replacing Light Bulbs..............................................................................................20
Preparing for Vacation.............................................................................................21
Puri Clean II......................................................................................................................23
State of California Water Certificate...............................................................................24
Operating Sounds............................................................................................................25
Troubleshooting...............................................................................................................26
Ice Maker.................................................................................................................28
Warranty........................................................................................................29
If You Need Service ................................................................................................30
Contents
Use & Care Guide
3
Important Safety Instructions
What You Need to Know
About Safety Instructions
Warning and Important Safety Instructions
appearing in this guide are not meant to cover all
possible conditions and situations that may
occur.
Common sense, caution and care must be exercised when installing, maintaining or operating
appliance.
Always contact the manufacturer about problems
or conditions you do not understand.
Recognize Safety Symbols,
Words, Labels
DANGER – Immediate hazards which WILL
result in severe personal injury or death.
WARNING – Hazards or unsafe practices which
COULD result in severe personal injury or death.
CAUTION – Hazards or unsafe practices which
COULD result in minor personal injury or proper-
ty damage.
Power Cord
This appliance is equipped with a 5 ft. (1.5 m)
power cord with three-prong grounding plug for
your protection against possible electrical shock
hazards.
It must be plugged into a 115 Volts 60Hz 10 amp
grounding receptacle.
Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced
with a properly grounded three-prong wall receptacle.
Do not under any circumstances, cut or remove
the third (ground) prong from the power cord.
Do not use an adapter plug.
To reduce risk of injury or death, follow basic
precautions, including the following:
IMPORTANT: Child entrapment and suffocation are not problems of
the past. Abandoned refrigerators are dangerous – even if they sit
out for “just a few days”.
If you are disposing of your old refrigerator, please follow the instructions below to help prevent accidents.
Before you throw away your old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so children may not easily climb inside.
Use & Care Guide
4
Important Safety Instructions
To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic precautions, including the following:
1) Read all instructions before using the refrigerator.
2) Observe all local codes and ordinances.
3) Be sure to follow grounding instructions.
4) Check with a qualified electrician if you are not
sure this appliance is properly grounded.
5) Do not ground to a gas line.
6) Do not ground to a cold-water pipe.
7) Refrigerator is designed to operate on a separate
115 volt, 15 amp, 60 cycle line.
8) Do not modify plug on power cord. If plug does
not fit electrical outlet, have proper outlet installed by a
qualified electrician.
9) Do not use a two-prong adapter, extension cord or
power strip.
10) Do not remove warning tag from power cord.
11) Do not tamper with refrigerator controls.
12) Do not service or replace any part of refrigerator unless specifically recommended in Use & Care
Guide or published user-repair instructions. Do not
attempt service if instructions are not understood or if
they are beyond personal skill level.
13) Always disconnect refrigerator from electrical
supply before attempting any service. Disconnect
power cord by grasping the plug, not the cord.
14) Install refrigerator according to Installation
Instructions. All connections for water, electrical power
and grounding must comply with local codes and be
made by licensed personnel when required.
15) Keep your refrigerator in good condition.
Bumping or dropping refrigerator can damage refrigerator or cause refrigerator to malfunction or leak. If
damage occurs, have refrigerator checked by qualified
service technician.
16) Replace worn power cords and/or loose plugs.
17) Always read and follow manufacturer’s storage
and ideal environment instructions for items being
stored in refrigerator.
18) Your refrigerator should not be operated in the
presence of explosive fumes.
19) Children should not climb, hang or stand on
any part of the refrigerator.
20) Clean up spills or water leakage associated
with water installation.
21) Ensure that the anti-tip bracket is installed as
per installation instructions.
SAVE THESE INSTRUCTIONS
Use & Care Guide
5
Installation
Your refrigerator has been packed carefully for
shipment. Remove and discard shelf packaging
and tape. Do not remove the serial plate.
The following pages contain “Measuring and
Opening” instructions particular to each of the
models and sizes. Ensure you choose the correct
instructions for your model.
• If refrigerator is installed beside a cooking appliance, (not recommended) it is important that there
be at least 5" (13 cm) between the refrigerator and
range for proper air circulation.
• Do not install refrigerator near a radiator or other
heat source. If not possible, shield refrigerator with
cabinet material.
• Do not install where temperature falls below 55°
F (13° C) or rises above 110° F (43° C).
Malfunction may occur at this temperature.
• Refrigerator is designed for indoor household
application only.
Measuring the Opening
(see page 10 diagram)
If refrigerator is to be installed into a recess verify
and use the following dimensions
1.) Cut out height for refrigerator, where the top of
the refrigerator is completely covered: 70” (177.8
cm) - space provides the necessary gap above
the refrigerator for tool access to fasten anti-tip
bracket (see details below)
2.) Cut out width for refrigerator’s main body: 36½"
(93 cm)
3.) Max. cut-out depth: 24 1/2” (62 cm)
When installing your refrigerator, measure
carefully. Allow ½" space at top and ½" space
behind the machine compartment cover (located in the rear) for proper air circulation.
AntiTip Bracket: Every refrigerator includes
an anti-tip bracket which must be properly
installed to prevent the refrigerator from tipping
forward should downward pressure be applied
with both doors
open. To fasten bracket to the wall, distance
from floor to underside of bracket will be 68-3/4
(174.6 cm) min to 69-1/4 (176 cm) max. Mark
wall where studs are located. Fasten anti-tip
bracket to the wall
Subflooring or floor coverings (ie carpet, tile,
wood floors, rugs) may make your opening
smaller than anticipated.
Some clearance may be gained by using the
leveling procedure under Leveling.
IMPORTANT! Corner Installations: To allow
door to open 90 degrees, corner installations
must allow 4” (10 cm) space between wall and
refrigerator on hinge side. Filler wood strip recommended for aesthetics.
Use & Care Guide
6
To protect property and refrigerator from damage, observe the following:
• Protect vinyl or other flooring with cardboard, rugs, or other protective material.
• Do not use power tools when performing levelling procedure
To enhance the appearance and maintain performance, the refrigerator should be level.
Materials Needed
• 3/8” hex head driver.
• Carpenter’s level.
Slide unit into opening, remove toe grill and
bracket covers.
Once unit is in place, adjust both front stabilizing legs (B) securely against floor.
1. Remove toe grille:
• Grasp firmly and pull
outward to unclip.
2. Remove bottom bracket cover(s).
• Place the eraser end of a pencil or similar blunt tool in the cover notch.
• Use slight pressure to pry the cover
loose.
• Continue to maintain
downward pressure to the
notched side of the cover
while swinging it off.
3. Using hex head driver, turn the front adjustment screws (A) on each side clockwise to raise or
counter-clockwise to lower the front of the refrigerator. (ensure the back of the unit is firmly under the
anti-tip bracket.)
4. There are rear adjustment screws (B). Using
the hex head driver, turn each of these adjustment
screws
(B) to raise or lower the rear of the refrigerator.
(ensure the back of the unit is firmly under the antitip bracket.)
5. Using the carpenter’s level, make sure front
of refrigerator is 1/4" (6 mm) or 1/2 bubble higher
than back of refrigerator and that the refrigerator is
level from side to side.
6. Turn stabilizing legs (C) clockwise until firmly
against floor.
7. Turn adjustment screws (A) counter clock
wise to allow the full weight of the refrigerator to rest
on the stabilizing legs.
8. Replace bracket cover(s):
• Position cover into the outer edge of the
hinge.
• Swing the cover toward the cabinet and snap
it into place.
9. Replace the toe grill.
Note:
• For proper reinstallation, ensure the “top”
marking on the interior of the toe grill is oriented correctly.
• Align the toe grill mounting clips with the
lower cabinet slots.
• Push the toe grill firmly until it snaps into
place.
Leveling
Connecting the Water Supply
To reduce the risk of injury or death, follow
basic precautions, including the following:
• Read all instructions before installing ice maker.
• Do not attempt installation if instructions are not under-
stood or if they are beyond personal skill level.
• Observe all local codes and ordinances.
• Do not service ice maker unless specifically recommended in Use & Care Guide or published user-repair
instructions.
• Disconnect power to refrigerator before installing ice
maker.
• Water damage due to an improper water connection
may cause mould/mildew growth. Clean up spills or leakage immediately
Use & Care Guide
7
Transporting Your Refrigerator
• NEVER transport refrigerator on its side. If an upright
position is not possible, lay refrigerator on its back. Allow
refrigerator to sit upright for approximately 30 minutes
before plugging it in to ensure oil returns to the compressor.
Plugging the refrigerator in immediately may cause damage
to internal parts.
• Use an appliance dolly when moving refrigerator.
ALWAYS truck refrigerator from its side or back–NEVER
from its front.
• Protect outside finish of refrigerator during transport by
wrapping cabinet in blankets or inserting padding between
the refrigerator and dolly.
• Secure refrigerator to dolly firmly with straps or bungee
cords. Thread straps through handles when possible. Do
not overtighten. Overtightening restraints may dent or damage outside finish.
To avoid property damage or possible injury,
follow basic precautions, including the following:
• Consult a plumber to connect 1/4” O.D. copper tubing
to household plumbing to assure compliance with local
codes and ordinances.
• Confirm water pressure to water valve is between 35
and 100 pounds per square inch, 20 pounds per square
inch if there is not a water filter.
• Do not use a self-piercing, or 3/16" saddle valve. Both
reduce water flow and can become clogged over time;
and may cause leaks if repair is attempted.
• Tighten nuts by hand to prevent cross threading.
Finish tightening nuts with pliers and wrenches. Do not
overtighten.
• Wait 2-3 hours before placing refrigerator into final
position to check and correct any water leaks. Recheck for
leaks after 24 hours.
• Verify the copper tubing under the sleeve is smooth,
cut square and free from defects. Do not reuse an old
sleeve.
Materials Needed
• 1/4" outer diameter flexible copper
tubing.
• Shut-off valve (requires a 1/4" hole
to be drilled into water supply line before
valve attachment).
• Adjustable wrench • 1/4" hex nut
driver.
• In-line water filter must be installed in
an accessible location to prevent damage to refrigerator’s water solenoid.
Note:
• Add 8' to tubing length needed to reach
water supply for creation of service loop.
1. Create service loop with copper tubing
(minimum 2’ diameter) Avoid kinks in the
copper tubing when bending it into a service
loop.
Use & Care Guide
8
• Set the freezer control on 4.
• Set the refrigerator control on 4.
• Let the refrigerator run at least 8 to 12 hours before
adding food.
Warm Cabinet Surfaces
At times, the front of the refrigerator cabinet may be
warm to the touch. This is a normal occurrence that
helps prevent moisture from condensing on the cabinet.
This condition will be more noticeable when you first
start the refrigerator, during hot weather and after excessive or lengthy door openings.
Adjusting the Controls
• 24 hours after adding food, you may decide that one
or both compartments should be colder or warmer. If so,
adjust the control(s) as indicated in the Temperature
Control Guide table below. See page 17 for instructions
on checking compartment temperature.
• Except when starting the refrigerator, do not change
either control more than one number at a time.
• Allow 24 hours for temperatures to stabilize
.
Temperature Control Guide
2. Remove plastic cap from water valve inlet
port.
3. Place brass nut (A) and sleeve (B) on copper
tube end as illustrated. Reminder: Do not use
an old sleeve.
4. Place end of copper tubing into water valve
inlet port. Shape tubing slightly. Do not kink –
so that tubing feeds straight into inlet port.
5. Slide brass nut over sleeve and screw nut
into inlet port. Tighten nut with wrench.
IMPORTANT: Do not overtighten. Cross
threading may occur.
6. Pull on tubing to confirm connection is secure. Connect
tubing to frame with water tubing clamp (C) and turn on
water supply. Check for leaks and correct if necessary.
Continue to observe the water supply connection for two to
three hours prior to moving the refrigerator to its permanent
location.
7. Monitor water connection for 24 hours. Correct leaks, if
necessary.
Touch Temperature Controls
The controls are located at the top front of the refrigerator
compartment.
Control
Initial Control Settings
After plugging the refrigerator in, set the controls as follows:
• Pressing the or pads adjusts the controls to
the desired setting.
• The temperature control range for both compartments is
1 through 7 (coldest).
Turn refrigerator OFF
Set the refrigerator control
to next higher number by
pressing the pad.
Set the refrigerator control
to next lower number by
pressing the pad.
Set the freezer control to
next higher number by
pressing the pad.
Set the freezer to next
lower number by pressing
the pad.
Press the refrigerator or
freezer pad until a
dash (-) appears on the display.
Refrigerator too warm
Refrigerator too cold
Freezer too warm
Freezer to cold
Use & Care Guide
9
Fresh Food Features
Shelves
To avoid personal injury or property damage, observe
the following:
• Never attempt to adjust a shelf that is
loaded with food.
• Confirm shelf is secure before placing
items on shelf .
• Handle tempered glass shelves carefully.
Shelves may break suddenly if nicked,
scratched, or exposed to sudden temper
ature change.
Your refrigerator has either Spillsaver™. The
Spillsaver™ shelves have a spill retainer edge which
allows for easier clean up and some are equipped with
the EasyGlide™ slide out feature. To slide out, grasp the
front of the shelf and pull forward. Push in the shelf to
return to the original position.
To Remove a Shelf:
• Slightly tilt up the front and lift up the
rear of the shelf, then pull the
shelf straight out.
To Lock the Shelf Into Another
Position:
• Tilt up the front edge of the shelf.
• Insert the hooks into the desired frame
openings and let the shelf settle into place.
• Be sure the shelf is securely locked at the rear.
The Crisper Top serves as the lower fresh food shelf .
To Remove the Crisper Top:
• Remove crisper drawers as indicated on
pages 10 and 11.
• Place hand under the frame to push up the
glass. Lift glass out.
• Lift frame from refrigerator liner rails.
• To install, repeat above instructions in
reverse order.
Dairy Center
The Dairy Center provides convenient door storage for
spreadable items such as butter and margarine.
This compartment can be moved to different locations to
accommodate storage needs.
To use the dairy center, raise the cover.
To Remove:
• Raise the cover, pull upward and tilt
out.
To Install:
• Reverse above procedure.
Door Buckets
Door Buckets can be moved to meet storage needs.
To Remove:
• Slide bucket up and pull straight out.
To Install:
• Slide bucket in and down until firmly
seated in the door liner.
Full-width Door Shelf
Full-width Door Shelf removes for easy cleaning.
To Remove:
• Slide shelf up and pull straight out.
To Install:
• Reverse above procedure.
Use & Care Guide
10
Rough In
Measurements
Dimensions
Use & Care Guide
11
Beverage Chiller™
The Beverage Chiller™ keeps bever-
ages and other items cooler than the
rest of the fresh food section. A cold air
inlet allows air from the freezer section
to pass into the beverage chiller. The
Beverage Chiller™ control is located
on the left wall of the fresh food compartment. The control adjusts the
amount of cold air allowed into the beverage chiller. For a cooler temperature
in the Beverage Chiller™ slide the control down.
To Remove:
• First remove the pick off
shelf to the left of the
Beverage Chiller™.
• Firmly hold each side of
beverage chiller, lift up and
away from door liner.
To Install:
• Reverse above procedure.
Note
• Cold air diverted into the Beverage Chiller™
can decrease the main refrigerator tempera
ture Refrigerator control may need to be
adjusted.
Crisper Drawers
The Crisper Drawers provide a higher
humidity environment for fresh fruit and vegetable storage.
Controls
The Crisper Controls regulate the amount
of humidity in the crisper drawer.
Slide the control toward the low setting for
produce with outer skins. Slide the control
toward the high setting for leafy produce.
To Remove:
• Pull drawer out to full extension Tilt up
front of drawer and pull straight out.
• Insert drawer into frame rails and push
back into place.
Note
• For best results, keep the crisper
drawers tightly closed.
Use & Care Guide
12
Temperature-Controlled Drawer
The Chef’s Pantry™ drawer is a full-width
drawer with adjustable temperature control. This
drawer can be used for large party trays, deli
items, beverages or other miscellaneous items.
There is a temperature control which adjusts the
amount of cold air allowed into the Chef’s
Pantry™. On the 36” the control is located on
the right side of the drawer under the lid.
Set the control to cold or to provide a normal
refrigerator temperature. Set the drawer on the
coldest or setting when a temperature colder
than the main refrigerator compartment is
desired. Use the coldest setting when storing
meats.
Notes
• Cold air directed to the Chef’s Pantry™
can decrease refrigerator temperature.
Refrigerator control may need to be adjusted.
• Do not place leafy vegetables in the
Chef’s Pantry™ drawer. Colder temperatures
could damage leafy produce.
To Remove:
• Lift lid. Pull drawer out to full extension.
Tilt up front of pantry and pull straight out.
To Install:
• Push metal glide rails to the back of the
refrigerator. Place drawer onto rails and slide
drawer back until it falls into place.
A divider is included to organize the Chef’s
Pantry™ into sections:
To Remove:
• Pull drawer completely out and raise the
front of the divider to unhook it from the rear
wall of the pantry and lift it out.
To Install:
• Hook back of divider over rear wall of
pantry and lower into place.
Accessories
Wine Trivet/Can Rack
The Wine Trivet/Can Rack
accessory fits in the Chef’s
Pantry™ or on a shelf.
Bottles or cans can be laid crosswise, or a single bottle may be
laid in the center depression.
Grip Pads
The Grip Pads prevent objects
from sliding in the door buckets.
Grip Pads are removable and are
top-rack dishwasher safe for easy
cleaning.
Use & Care Guide
13
Freezer Features
To prevent accidental child entrapment or
suffocation risk, do not remove the divider in
the top freezer basket.
Lower Wire Basket
To Remove:
• Pull open the freezer door to full extension and lift up
and out of the door rail to remove.
To Install:
• Lower into door rail. Make sure that the basket sits
flush into place. To prevent accidental child entrapment or
suffocation risk, do not remove the divider in the freezer
basket.
Upper Wire Basket
To Remove:
• Pull upper basket out to full extension and lift out to
remove.
To Install:
• Slide upper basket into freezer. Make sure that rear of
basket hooks behind rail catch. To prevent accidental child
entrapment or suffocation risk, do not remove the divider
in the top freezer basket.
Ice and Water
Automatic Ice Maker
Note
• Energy rating guides that are posted on
the refrigerator at the time of purchase do
not include optional ice maker energy
usage.
Only 36” models come equipped with an automatic ice
maker.
Connect the ice maker to the water supply as instructed
on page 7. Proper water flow and a level refrigerator
are essential for optimal ice maker performance.
Operating Instructions
• Confirm ice bin is in place and ice maker arm is
down.
• After freezer section reaches approximately 0° F (-18°
C), ice maker fills with water and begins operating.
You will have a complete harvest of ice approximately
every three hours.
• Allow approximately 24 hours after installation to
receive first harvest of ice.
• Discard ice created within first 12 hours of operation
to assure system is flushed of impurities.
• Stop ice production by raising ice maker arm until
click is heard.
• Ice maker will remain in the off position until arm is
pushed down.
• The first one or two batches will probably contain
undersized and irregular cubes because of air in the
supply line.
• When the ice cubes are ejected it is normal for sever
al cubes to be joined together at the ends. They can
easily be broken apart. The ice maker will continue to
make ice until the supply of ice cubes raises the sen
sor arm, shutting the ice maker off .
• If bucket is not positioned properly it may prevent
automatic shut-off as ice cubes may not accumulate
to raise the sensor arm.
Use & Care Guide
14
• Certain sounds may accompany the various cycles of
the ice maker. The motor may have a slight hum, the
cubes will rattle as they fall into an empty storage pan and
the water valve may click or “buzz” occasionally.
• If the ice is not used frequently, the ice cubes will
become cloudy, shrink, stick together and taste stale.
Empty the ice storage bin periodically
and wash it in lukewarm water. Be
sure to dry the bin thoroughly before
replacing it .
• Beverages and foods should not
be placed in the ice storage bin for
quick chilling. These items can block
the sensor arm, causing the ice maker to malfunction.
• Turn off (arm up) the ice maker when the water supply is to be shut off for several hours.
To Remove the Ice Bin:
• Pull it forward, away from the ice maker. To avoid the
ice maker dumping ice while the bin is removed, turn the
ice maker off by raising the sensor arm.
To Install the Ice Bin:
• Reverse the above procedure. Turn the ice maker on
by lowering the sensor arm.
To avoid personal injury or property damage,
observe the following:
• Do not place fingers or hands on the
automatic ice making mechanism while the
refrigerator is plugged in. This will help pro
tect you from possible injury. It will also pre
vent interference with moving parts of the
ejector mechanism and the heating element
that releases the cubes.
• Under certain rare circumstances, ice cubes
may be discolored, usually appearing with a
green-bluish hue. The cause of this unusual
discoloration can be a combination of factors
such as certain characteristics of local waters,
household plumbing and the accumulation of
copper salts in an inactive water supply line
which feeds the ice maker. Continued
consumption of such discolored ice cubes
may be injurious to health. If such
discoloration is observed, discard the ice
cubes and contact your dealer to purchase
and install a water line filter.
• Water damage due to improper water
connection may cause mold/mildew growth.
• Clean up water and ice spills to avoid person
al injury and to prevent mold/mildew growth.
Ice and Water
Water Dispenser
The Water Dispenser is located on the left side wall of
the fresh food section. This design is
for cold water dispensing only.
To Dispense Water:
• Hold container under spout and
press dispenser pad.
Use & Care Guide
15
Water Filter
To avoid serious illness or death, do not use
refrigerator where water is unsafe or of unknown
quality without adequate disinfection before or
after use of filter.
After installing a new water filter, always dispense
water for two minutes before removing the filter
for any reason.
• The bypass cap does not filter water. Be sure to
have replacement cartridge available when filter
change is required.
• If water filtration system has been allowed to
freeze, replace filter cartridge.
• If system has not been used for a short period of
time, and water has an unpleasant taste or odor,
flush system by dispensing two to three glasses
of water. If unpleasant taste or odor persists,
change filter cartridge. If system has not been
used for three months or more, replace water filter
cartridge (see page 26).
Initial Installation
The water filter is located in the upper right hand corner of
the fresh food compartment:
1. Remove blue bypass cap and retain
for later use.
2. Remove sealing label from end of fil
ter and insert into filter head.
3. Rotate gently clockwise until filter
stops. Snap filter cover closed.
4. Reduce water spurts by flushing air from system. Run
water continuously for two minutes through dispenser
until water runs steady. During initial use, allow about
a one- to two-minute delay in water
dispersal to allow internal water
tank to fill.
• Additional flushing may be required
in some house holds where water
is of poor quality.
Replacing Water Filter
IMPORTANT: Air trapped in system may cause
water and cartridge to eject. Always dispense
water for two minutes before removing the filter for
any reason. Use caution when removing.
1. Turn filter counter clockwise until it releases from filter
head.
2. Drain water from filter into sink, and dispose in normal
household trash.
3. Wipe up excess water in filter cover and continue with
Initial Installation, steps 2 and 4. The filter should be
changed at least every 12 months.
IMPORTANT: Condition of water and amount used determines life span of water filter cartridge.
If water use is high, or if water is of poor quality, replacement may need to take place more often.
To purchase a replacement water filter cartridge, contact
your dealer or call 1-877-650-5775 EXT 2362 and ask for
#31104 Clean n’ Clear water filter.
The dispenser feature may be used without a water filter
cartridge. If you choose this option, replace filter with blue
bypass cap.
Use & Care Guide
16
Food Storage Tips
Fresh Food Storage
• The fresh food compartment of a refrigerator should
be kept between 34° and 40° F (1° and 4° C) with an optimum temperature of 37° F (3° C), To check the temperature, place an appliance thermometer in a glass of water
and place in the centre of the refrigerator. Check after 24
hours. If the temperature is above 40° F (4° C) adjust the
controls as explained on page 8.
• Avoid overcrowding the refrigerator shelves. This
reduces the circulation of air around the food and results
in uneven cooling .
Fruits and Vegetables
• The crisper drawers trap humidity to help preserve the
fruit and vegetable quality for longer time periods (see
page 11).
• Sort fruits and vegetables before storage and use
bruised or soft items first. Discard those showing signs of
decay.
• Always wrap odorous foods such as onions and cabbage so the odor does not transfer to other foods.
• While vegetables need a certain amount of humidity
to remain fresh, too much humidity can shorten storage
times (especially leafy vegetables). Drain vegetables well
before storing.
• Wait to wash fresh produce until right before use.
Meat and Cheese
• Raw meat and poultry should be wrapped securely so
leakage and contamination of other foods or surfaces
does not occur.
• Occasionally mold will develop on the surface of hard
cheeses (Swiss, Cheddar, Parmesan). Cut off at least an
inch around and below the mouldy area. Keep your knife
or instrument out of the mold itself. Do not try to save individual cheese slices, soft cheese, cottage cheese, cream,
sour cream or yogurt when mold appears.
Dairy Food
• Most dairy foods such as milk, yogurt, sour cream
and cottage cheese have freshness dates on their cartons
for appropriate length of storage. Store these foods in the
original carton and refrigerate immediately after purchasing and after each use.
Frozen Food Storage
• The freezer compartment of a refrigerator should be
kept at approximately 0° F (-18° C). To check the temperature, place an appliance thermometer between the
frozen packages and check after 24 hours. If the temperature is above 0° F (-18° C), adjust the control as
described on page 8.
• A freezer operates more efficiently when it is at least
two-thirds full .
Packaging Foods for Freezing
• To minimize dehydration and quality deterioration use
aluminium foil, freezer wrap, freezer bags or airtight containers. Force as much air out of the packages as possible and be sure they are tightly sealed. Trapped air can
cause the food to dry out, change colour and develop an
off-flavour (freezer burn).
• Overwrap fresh meats and poultry with suitable freez-
er wrap prior to freezing.
• Do not refreeze meat that has completely thawed.
Loading the Freezer
• Avoid adding too much warm food to the freezer at
one time. This overloads the freezer, slows the rate of
freezing and can raise the temperature of frozen foods.
• Leave space between the packages so cold air can
circulate freely, allowing food to freeze as quickly as possible.
• Avoid storing hard-to-freeze foods such as ice cream
and orange juice on the freezer door shelves. These
foods are best stored in the freezer interior where the
temperature varies less with door openings.
Refer to the Food Storage Chart on pages 18 and 19 for
approximate storage times.
Use & Care Guide
17
Food Storage Chart
Storage times are approximate and may vary depending on type of packaging, storage temperature, and the quality of
the food when purchased.
Use & Care Guide
18
Sources: United States Department of Agriculture; Food Marketing Institute; Cooperative Extension Service, Iowa State
University.
Use & Care Guide
19
To avoid electrical shock which can
cause severe personal injury or death,
disconnect power to refrigerator before
cleaning.
After cleaning, reconnect power.
To avoid personal injury or property damage, observe the following:
• Read and follow manufacturer’s direc
tions for all cleaning products.
• Do not place buckets, shelves or acces
sories in dishwasher. Cracking or
warping of accessories may result.
Use & Care Guide
20
Care and Cleaning
To avoid electrical shock which can cause
severe personal injury or death, discon
nect power to refrigerator before clean
ing. After cleaning, reconnect power.
Cleaning the Outside
Circuit breakers must be shut off before
cleaning. Using a damp cloth and mild dish-
washing detergent, wipe surface lightly. Dry and
polish with a clean, soft cloth. Do not wipe panel
with a soiled dishcloth or wet towel, these may
leave residue that can erode the paint. Do not
use scouring pads, powdered cleaners, or
bleach because these products can scratch,
and/or weaken the paint. Wring excess water
from sponge or cloth to avoid excess moisture,
especially when cleaning in vicinity of switches,
lights or controls.
Removing Odors From
Refrigerator
1. Remove all food and turn the refrigerator
OFF.
2. Disconnect power to the refrigerator.
3. Clean the walls, floor, ceiling of cabinet inte-
rior, drawers, shelves and gaskets according to
the instructions on page 20 and 21.
• Clean condenser coils as indicated in the
cleaning instructions every three months. This
will increase energy efficiency and cooling performance.
Replacing Light Bulbs
To avoid electrical shock which can
cause severe personal injury or death,
disconnect power to refrigerator before
replacing light bulb. After replacing light
bulb, reconnect power.
To avoid personal injury or property dam
age, observe the following:
• Allow light bulb to cool.
• Wear gloves when replacing light bulb.
Fresh Food Section
(style of light shield varies)
1. Slide clear light shield toward back of com
partment to release from light assembly.
2. Remove light bulbs.
3. Replace with appliance bulbs no greater
than 40 watts.
4. Replace light bulb cover by inserting tabs on
light shield into liner holes on each side of
light assembly. Slide shield toward front of
refrigerator until it locks into place. Do not
force shield beyond locking point. Doing so
may damage light shield.
Use & Care Guide
21
Freezer (style of light shield varies)
1. Reach behind the light cover.
2. With firm pressure, press forward
on the notches at the back of the
cover and pull down the cover will
open from the back.
3. Remove the cover.
4. Remove light bulb.
5. Replace bulb with appliance bulb
no greater than 40 watts.
6. Insert front tabs of light cover into
slots in freezer liner and snap rear
portion over light assembly until
rear tab engages.
Preparing for Vacation
If your refrigerator has a dispenser and there is
any possibility that the temperature can drop
below freezing where the refrigerator is located,
the water supply system (including the water tank
and the water valve) must be drained by a quali
fied servicer.
For short vacations or absences (three months or
less):
1. Remove all perishables.
2. If no one will be checking in on the refrigerator
during your absence, remove all frozen items also.
3. Automatic ice maker:
• Shut off the water supply to the ice
maker at least one day ahead of time.
• After the last load of ice cubes drop, raise the wire
shut off arm to the OFF position.
• Empty the ice bin.
4. If the room temperature will drop below 55°F(13° C),
follow the instructions for longer absences.
For long vacations, absences (more than three
months) OR if the room temperature will drop below
55º F (13° C):
1. Remove food.
2. Ice maker:
• Shut off the water supply to the ice maker at least
one day ahead of time.
• After the last load of ice drops, raise the wire shut off
arm to the OFF position.
• Empty the ice bin.
3. If your refrigerator has a dispenser system with water
filter, remove the water filter cartridge and install the
filter bypass. Dispose of the used cartridge.
4. Turn the freezer control to (OFF) with dial controls or
(—) with touch controls (see page 8).
5. Unplug the refrigerator.
6. Thoroughly clean the interior of both compartments
with a baking soda solution and a clean soft cloth
(four tablespoons of baking soda in one quart of warm
water).
7. Dry thoroughly.
8. Leave the doors open to prevent the formation of
mold and mildew.
Upon your return:
After a short vacation or absence:
Ice makers and dispenser:
• Reconnect the water supply and turn on supply valve
(see page 7).
• Monitor water connection for 24 hours and correct
leaks if necessary.
• Run 10-15 glasses of water from the dispenser to
flush out the system.
• Restart the ice maker.
• Discard at least the first three ice harvests.
After a long vacation or absence:
• If your refrigerator has an automatic ice maker, recon
nect the water supply and turn on supply valve (see
page 8).
• Plug the refrigerator back in and reset controls (see
page 8).
Use & Care Guide
22
After a long vacation or absence:
• If your refrigerator has an automatic ice
maker, reconnect the water supply and turn
on supply valve (see page 8).
• Plug the refrigerator back in and reset con
trols (see page 8).
• Monitor water connection for 24 hours and
correct leaks, if necessary. For dispenser
models, run water through the dispenser
for at least three minutes with the filter
bypass in place, then install water filter
(see pages 13/14).
• After installing the water filter, run water
through the dispenser continuously for at
least two minutes, or until water runs
steady. Initially you may notice a one-two
minute delay in water dispersal as the
internal tank fills.
• Restart the ice maker.
• Discard ice produced within the first 12
hours (at least the first three harvests).
Preparing to move:
• Follow the above instructions for long vaca
tions/absences, through step 7.
• Secure all loose items such as shelves and
drawers by taping them securely in place to
prevent damage.
• Tape the doors shut.
• Use an appliance dolly when moving the
refrigerator. Always truck the refridgeerator
from its side or back never from its front.
• Be sure the refrigerator stays in an upright
position during moving.
Use & Care Guide
23
System Specification and Performance Data Sheet
Refrigerator Water Filter Cartridge Model UKF8001AXX
Specifications
Service Flow Rate (Maximum) 0.78 GPM (2 9 L/min)
Rated Service Life UKF8001AXX-750 (Maximum) 750 gallons/2839 liters
Maximum Operating Temperature 100° F / 38° C
Minimum Pressure Requirement 35 psi /241 kPA
Minimum Operating Temperature 33° F/1° C
Maximum Operating Pressure 100 psi / 689 kPA
PentaPure Inc.
1000 Apollo Road
Eagan, Minnesota 55121-2240
651 450 4913
EPA EST #35917-MN-1
100834/B
* Tested using a flow rate of 0.78 gpm; pressure of 60 psig;
pH of 7.5 + 0.5; temp. of 68° + 5° F (20° + 3° C)
** Measurement in Particles /ml. Particles used were 0.5 -
1 microns
*** NTU - Nephelometric Turbidity Units
General Use Conditions
Read this Performance Data Sheet and compare the capabilities of this unit with your actual
water treatment needs.
DO NOT use this product where water is
microbiologically unsafe or of unknown
quality without adequate disinfection before
or after the system. System certified for cyst
reduction may be used on disinfected water
that may contain filterable cysts.
USE ONLY WITH COLD WATER SUPPLY.
CHECK FOR COMPLIANCE WITH THE
STATE AND LOCAL LAWS AND REGULATIONS.
Tested and certified by NSF International against ANSI/NSF Standards
42 & 53 in models UKF8001AXX-750 for the reduction of:
The PuriClean® II retractable water filtration system uses a
UKF8001AXX replacement cartridge. Timely replacement of filter
cartridge is essential for performance satisfaction from this filtration system.
Please refer to the applicable section of your Use & Care Guide
for general operation, maintenance requirements and troubleshooting.
This system has been tested according to ANSI/NSF 42 and 53
for reduction of the substance listed above. The concentration of
the indicated substances in water entering the system was
reduced to a concentration less than or equal to the permissible
limit for water leaving the system, as specified in ANSI/NSF 42
and 53.
Standard No. 42: Aesthetic Effects
Taste and Odor Reduction
Chlorine Taste & Odor
Mechanical Filtration Unit
Particulate Reduction Class 1
Standard No. 53: Health Effects
Chemical Reduction Unit
Lead, Atrazine, Lindane, Mercury &
Toxaphene Reduction
Mechanical Filtration Unit
Cyst, Turbidity and Asbestos
reduction
Use & Care Guide
24
State of California
Department of Health Services
Water Treatment Device
Certificate Number
03 - 1583
Date Issued:September 16,2003
Date Revised:April 22,2004
Trademark /Model Designation Replacement Elements
UKF8001AXX750 UKF8001AXX
469006-750 46 9006
67003523-750 67003523
Manufacturer: PentaPure Inc.
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants:
Microbiological Contaminants and Turbidity Inorganic/Radiological Contaminants
Cysts Asbestos
Turbidity Lead
Mercury
Organic Contaminants
Atrazine
Lindane
Benzene
Carbofuran
p-dichlorobenzene
Toxaphene
Rated Service Capacity: 750 gal. Rated Service Flow: 0.78 gpm
Conditions of Certification:
Do not use where water is microbiologically unsafe or with water of unknown quality, except that sys-
tems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Use & Care Guide
25
Operating Sounds
Improvements in refrigeration design may produce sounds in your new refrigerator that are different
or were not present in an older model. These improvements were made to create a refrigerator that
is better at preserving food, is more energy efficient, and is quieter overall. Because new refrigerators run quieter, sounds may be detected that were present in older refrigerators, but were masked
by higher sound levels.
Many of these sounds are normal. Please note that the surfaces adjacent to a refrigerator, such as
hard walls, floors and cabinetry may make these sounds seem even louder. The following are some
of the normal sounds that may be noticed in a new refrigerator.
Use & Care Guide
26
Troubleshooting
Use & Care Guide
27
Use & Care Guide
28
Ice
Warranty
REFRIGERATOR MODELS
AFHR-36-
Entire Product – Limited One Year Warranty
Aga-Heartland warrants that it will supply all necessary parts and labour to repair or replace in your home, any component
which proves to be defective in material or workmanship, with the exception of painted or porcelain enamel finish, or plated
surfaces. Subject to the conditions and exclusions stated below, for the period of one year from date of sale.
The warranty period against defects in the painted enamel finish, or plated surfaces, is 90 days from date of original purchase.
Limited Warranty - Major Refrigeration Components
Second Through Fifth Year - After the first year from the date of original purchase, through the fifth year, the manufactur-
er will repair or replace, at its option, free of charge for parts and labor only, any part of the sealed refrigeration system (consisting of the compressor, evaporator, condenser, drier and connecting tubing) and the cabinet liner (exclusive of the door
liner) which fail in normal home use. All other costs, including mileage, transportation, trip charge and diagnostic charge, if
required, shall be the responsibility of the owner.
Limited Warranty
30 days - From the original retail purchase date, any part of the water filter cartridge which fails due to a defect in workman-
ship or materials will be replaced free of charge.
What is not covered by this Warranty
1. Customer education or instructions on how to use the refrigerator/freezer.
2. Any food loss due to product failure. (Warrantor is not be liable for any incidental or consequential damage including
food loss)
3. Any expenses involved in making this appliance readily accessible for servicing.
4. Transportation, delivery, or subsequent damages.
5. Commercial, rental, or use other than normal household.
6. Improper installation, misuse, abuse, accident or alteration, use on wiring not conforming to electrical codes, low
voltage, failure to provide necessary maintenance or other unreasonable use.
7. Parts of service not supplied or designated by the factory.
8. Accident, fire, flood, acts of God.
9. Alteration, or the removal or defacing of the serial plate.
10. The original Bill of Sale, delivery date or serial number cannot be verified.
11. The product is moved from place of original installation, and reinstalled without reviewing installation procedures with
dealer or manufacturer.
12. Light bulbs
THE WARRANTIES, SET FORTH HEREIN ARE THE ONLY WARRANTIES EXTENDED BY AGA RANGES. ANY IMPLIED
WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE DURATION OF
THESE EXPRESS WARRANTIES. IN NO EVENT SHALL AGA RANGES BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES OF EXPENSES RESULTING FROM BREACH OF THESE OR ANY OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED. Some states do not allow the exclusion or limitation of consequential damages or
limitations on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. Warranty
applies to product only in the country in which it was purchased.
No person, firm or corporation is authorized to make any other warranty or assume any other obligation for Aga-Heartland.
To obtain performance of the warranty, report any defects to: Your Dealer or Aga Ranges Service Representative.
Aga-Heartland.
1050 Fountain St.
Cambridge, ON
N3H 4R7, Canada
Business 1-877-650-
5775
Fax 1-800-327-5609
PLACE OF PURCHASE_________________________________
DATE OF PURCHASE__________________________________
SERIAL NUMBER_____________________________________
MODEL NUMBER_____________________________________
Use & Care Guide
30
Warranty & Service
What is Not Covered By These
Warranties:
1. Conditions and damages resulting from any of the following:
a. improper installation, delivery, or maintenance.
b.Any repair, modification, alteration, or
adjustment not authorized by the manufacturer or an
authorized servicer.
c. Misuse, abuse, accidents, or unreasonable use.
d. Incorrect electric current, voltage, or supply.
e. Improper setting of any control.
f. damage caused by low water pressure (reverse osmosis
filter system)
2. Warranties are void if the original serial numbers have been
removed, altered or cannot be readily determined.
3. Light bulbs.
4. Products purchased for commercial or industrial use.
5. The cost of service or service call to:
a. Correct installation errors.
b. Instruct the user on the proper use of the
product.
c. Transport the appliance to the servicer.
6. Consequential or incidental damages sustained by any per
son as a result of any breach of these warranties.
Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not
apply.
If You Need Service
• Call the dealer from whom your appliance was purchased
or call Aga Ranges Customer Assistance locate an author
ized servicer.
• Be sure to retain proof of purchase to verify warranty status.
Refer to Warranty for further information on owner’s respon
sibilities for warranty service.
• If the dealer or service company cannot resolve the prob
lem, write to:
Aga-Heartland.
1050 Fountain St.
Cambridge, ON
N3H-4R7 Canada
or call:
Aga Ranges Customer Assistance,
Toll Free Phone 1-877-650-5775
• User’s guides, service manuals and parts information are
available from Aga Rranges Customer Assistance.
Note
• When writing or calling about a service problem, please
include the following information:
a. Your name, address and telephone number;
b. Model number and serial number;
c. Name and address of your dealer or servicer;
d. A clear description of the problem you are having;
e. Proof of purchase (sales receipt).
Note
The full warranty and the limited warranties apply only when the
refrigerator is located in the United States or Canada.
Refrigerators located elsewhere are not covered by this warranty. Warranty applies to product only in the country in which
it was purchased.
In our continuing effort to improve the quality and performance
of our appliances, it may be necessary to make changes to the
appliance without notice. Such revisions do not entitle purchaser
to corresponding changes, improvements, additions, or replacements for previously purchased equipment.
Loading...