AFX HZP620SNSCTD User Manual

HZP Series Fluorescent Pendant

Models 413/613

Safety Precautions

Read all safety precautions and installation instructions carefully
before installing or servicing this fixture. Failure to comply with
these instructions could result in potentially fatal electric shock
and/or property damage.

It is recommended that a qualified electrician perform all wiring. This
fixture must be wired in accordance with all national and local
electrical codes.

Do not handle any energized fixture or attempt to energize any
fixture with wet hands or while standing on a wet or damp surface or
in water.

Make sure that the power source conforms to the requirements of the
fixture. (See labels on fixture housing).

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing any part of this fixture.
B. Unpack and lay out all fixture components to verify everything is included to fully assemble the fixture.
C. Please affix all stems with supplied thread locker to prevent stems from coming undone when assembled.

2. Fixture assembly - Lighting fixture is partially assembled

A. Take the fixture power wires (black and white) and feed them

through the 1-½” stem assembly (10). Thread the stem assembly
into the fitting on top of the ballast/lamp tray until secure.

B. Slide diffuser support (11-only found on 6-lamp unit) over 1

½” stem assembly and allow it to rest on top of the ballast/lamp
mounting tray. NOTE: Verify Step 2C is completed prior to
moving on for the 6-lamp unit only.

C. Feed wires through the ½” nipple (8B) and stem (9) and screw

the stem into nipple on top of the 1-½” stem (10).

NOTE: Two 6” and two 12” stems included for

desired height between 1-½” stem and canopy.

D. Slide wires through ½” threaded nipple (8A) and screw nipple

¼” into stem (9) and swivel assembly (6). Slide wires through
swivel (6) and canopy (5) assembly and tighten.

3. Fixture mounting.

A. Install short screws (2) provided into threaded holes near ends

of gem bar (3). Be sure these screws line up with holes in
canopy.

B. Insert 1 ½” (4) screws through slots in gem bar (3) and

secure to junction box in ceiling (not provided). Be sure short
screws (2) in gem bar (3) pointing down. Slide supply wires
through center hole of mounting bracket.

4. Wiring.
Caution: Make sure power is off at fuse or circuit breaker box. Check

power wires for damage or scrapes. If power supply wires are within
three inches of ballast use wire suitable for at least 90C (194F). Note:
Most dwellings built before 1985 have supply wire rated to 60C.
Consult a qualified electrician before installing.

*MV model shown with 4-pin CFL’s

Models ending in MV power source 120-277V Non-dimmable

Models ending in SCTD power source 120V (Self Ballasted
dimmable CFL) Usable on a dimming circuit with dimmable lamps

To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding there must be a separate ground wire (green) or bare metal
contact (metal conduit) between this fixture and the ground
connection of your main power supply panel.

This fixture is intended for use as general lighting in dry or damp
locations.

Page 1 of 2 8060464 Rev. 8

HZP Series Fluorescent Pendant

Models 413/ 613

A. This unit will not operate properly unless connected to a “grounded” electrical circuit. Electrical shock, over

heating, low or no light output, and shortened lamp life can result if proper is not properly grounded. Securely
attach green (or green and yellow) wire to ground.

B. Using wire connectors (1) provided, connect white supply wire to white ballast lead. Connect black hot supply

wire to black ballast lead. Do not mix wires. Pull on each wire to make sure connections are secure. Make certain
no bare wires are exposed outside of wire connectors.

C. Line-up the two holes in the canopy (5) with the two screws in the mounting bracket. Secure fixture to screws

with the thumb nuts (7) provided.

5. Lamp Installation (Lamps included on models ending with “SCTD”).

A. For model ending in MV, use only 13 watt fluorescent, quad 4-pin lamps (12). To install,

line-up lamp pins with the corresponding holes in the lamp socket (13) and push lamp into
place until a click is heard. Repeat for each lamp.

B. For models ending in SCTD (See Detail B) usable on a dimming circuit with dimmable

GU24 base lamps, use only GU24 base lamps (26W max.). To install, line up lamp pins
with the corresponding holes in lamp socket and turn clockwise until a click is heard. Repeat
for each lamp.

NOTE: BE CAREFUL NOT TO ROTATE PENDANT DURING LAMP
INSTALLATION/REPLACEMENT

6. Diffuser Installation

A. On the 6-lamp unit, line up the diffuser support (11) with the tabs (15) on the inside of the

diffuser (16); they should rest under each tab.

B. Thread long nipple with cap (14) into fitting in bottom of ballast housing assembly

approximately ¼”. Line up center hole in diffuser (16) with cap, center hole in cap to nipple and secure with finial
(17).

C. For the 4-lamp unit (see Detail C), there is a hang straight (D) for the diffuser. Thread the long nipple (C) into the

coupling (G) on hub (A) and use hexnut (B) to keep the stem from rotating. Next, thread the hang straight (D)
onto the nipple (C). Place the diffuser collar (E) into the center hole on the diffuser (F) and place them into the
threaded part of the hang straight and tighten with finial (F). Use a level to adjust the diffuser from the top side.

DETAIL C

DETAIL B

Limited Factory Warranty
American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under
normal operating conditions for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement
of defective fixture or components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

Page 2 of 2 8060464 Rev. 8