AFX CZP226QSNMV-WHWH User Manual

CZP Series Fluorescent Pendants

FIG 1

FIG 2

Models 218MV / 218SCT / 226MV / 226SCT

Safety Precautions

Read all safety precautions and installation instructions carefully
before installing or servicing this fixture. Failure to comply with
these instructions could result in potentially fatal electric shock
and/or property damage.

It is recommended that a qualified electrician perform all wiring. This
fixture must be wired in accordance with all national and local
electrical codes.

Do not handle any energized fixture or attempt to energize any
fixture with wet hands or while standing on a wet or damp surface or
in water.

Make sure that the power source conforms to the requirements of the
fixture. (See labels on fixture housing).

Assembly Instructions

1. Preparing for installation

A. Disconnect electrical power before installing or servicing any part of this fixture.
B. Unpack and lay out all fixture components to verify everything is included to fully assemble the

fixture.

C. Affix all aircraft cables with supplied connector adapters to prevent cables from coming undone when

assembled.

2. Fixture assembly – fixture is partially assembled (Fig 2)

A. Canopy with Cord / Cable Assembly:

 Feed the two cables (11) through the connectors (8) that are mounted on the

canopy (7). Insert the cable by pressing the “Spring Pin” (8) upward and
holding until cable comes out at the other end. Repeat these steps for the
other cables. Note: Cable length adjustments might be needed again for the
correct cord length alignment.

B. Take the fixture power cord wires (12) and slide them through the canopy strain

relief assembly (10).

C. Cord Length Adjustments / Cutting / Stripping Wire Ends:

 Before cutting the cord, measure the desired cord length for pendant

mounting. Tighten the strain relief by threading tapered metal finial to
mechanically secure the cord.

 For wiring NEC (National Electrical Code) requirements, cut the cord about

7” from the canopy (7) as shown.

 Cut the cord outside jacket insulation about 3” from canopy (7) and then

strip 3/8” from the ends of the three wires (6) as shown in Fig 2.

3. Fixture mounting from Junction Box (Fig 1 & 2)

A. Install the short screws (1) with lock washers (3) and hex nuts (4) all provided

into the offset holes (2) of the round mounting bracket. Be sure the two screws
(1) line up with the holes on the canopy (7) and point away from junction box.

Note: These short screws (1) may require length adjustment to mount the
two thumb nuts (9) correctly.

B. Install and secure the round mounting bracket assembly to the junction box (not

provided) in ceiling with the longer screws (5) provided.

4. Wiring Canopy Cord Assembly to Junction Box (Fig 1 & 2)
Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for

damage or scrapes. If power supply wires are within three inches of ballast use wire
suitable for at least 90C (194F). Note: Most dwellings built before 1985 have supply
wire rated to 60C. Consult a qualified electrician before installing.

Page 1 of 2 8060722 R0

Models ending in “MV” can be supplied with 120-277VAC.
These units are NOT DIMMABLE.

Models ending in “SCT” must be powered with 120VAC ONLY.
The units can be used with an approved dimmer (contact AFX

Lighting Customer Service for dimming information).
To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper
grounding there must be a separate ground wire (green) or bare metal
contact (metal conduit) between this fixture and the ground
connection of your main power supply panel.

This fixture is intended for use as general lighting in dry or damp
locations.

CZP Series Fluorescent Pendants

Limited Factory Warranty
AFX Lighting, Inc. warrants this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions
for a period of 3 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

FIG 4

FIG 3

Models 218MV / 218SCT / 226MV / 226SCT

A. Attach the cord green (or clear) wire to the incoming supply ground wire.
B. Models ending in MV: Using luminaire disconnect adapter provided, insert white supply

wire into the hole across from white ballast lead. Insert black hot supply wire into hole
across from black ballast lead. Do not mix wires.

C. Models ending in SCT: Use wire connectors provided to connect incoming white supply

wire to cord white wire. Connect incoming black supply wire to cord black wire. Do not
mix wires.

D. Pull on each wire to make sure connections are secure. Make certain no bare wires are

exposed outside of wire connectors.

E. Line up the two holes in the canopy (7) with the two screws in the round mounting

bracket. Secure fixture to screws with the two cylindrical thumb nuts (9) provided.

5. Aircraft Cable Adjustments.

A. Adjust the aircraft cables up and down by pressing the “Spring Pin” (8) upward and

holding until the proper cable length is attained. Repeat the same steps to the other cable
assembly. Note: Extra cable length should be looped or tied inside the canopy.

6. Lamp Installation (lamps included on models ending with “SCT”).

A. For models ending in MV, use only 18W/26W (max) fluorescent, quad 4-pin lamps (21). To install, line up lamp pins with

the corresponding holes in the lamp socket (2 0) and push lamp into place until a click is heard. Repeat for each lamp.

B. Models ending in SCT use a GU24 base lamp (18W/26W max). To install, line up lamp pins with the corresponding holes in

lamp socket and turn clockwise until a click is heard (Fig 4). Repeat for each lamp.

NOTE: BE CAREFUL NOT TO ROTATE PENDANT DURING LAMP
INSTALLATION/REPLACEMENT

7. Inner and Outer Shades Installation (Fig 2 & 3)

A. Install the inner shade assembly (19) to the ballast / wire compartment assembly plate (17). Make sure

the flat head screws (15) are mechanically secure to the top of the plate.

B. Install the outer shade (13) by setting the wireform (14) on top of the perimeter of the inner shade (19)

as shown in Fig 3.

8. Diffuser Installation (Fig 2)

A. Install the plastic diffuser (22) by inserting at an angle and realign to set freely by gravity at the bottom

wireform of the inner shade (19).

Page 2 of 2 8060722 R0