AFX CNP340041LSNYWH User Manual

CENTRE LED PENDANTS

Models:

CNP3400 Series

Safety Precautions

Read all safety precautions and installation instructions carefully before

this fixture. Failure to comply with these

instructions could result in potentially fatal electric shock and/or

commended that a qualified

fixture must be wired in accordance with all national and local

Do not handle any energized fixture or attempt to energize any fixture

with wet hands or while standing on a

INSTRUCTIONS

Preparing for installation

Disconnect electrical power

Carefully remove the fixture from the carton, and check that all parts are included,

below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.

all wiring must take place inside junction box.

Make sure power is off at fuse or circuit breaker box. Chec

power wires for damage or scrapes. If

Most dwellings built before 1985 have supply wire rated to 60C.

rician before installing.

screws (3) and r

plate

Mark two mounting holes locations on the ceiling by us

plate as a template. Remove the gem bar plate and drill two holes for the

anchors (13) supplied. Install the anchors.

install the gem bar plate (1) by securing it with two screws (2) on the

junction box and two screws (14) on the ceiling.

connections

Connect the green wire

The black wire from the fixture is connected to the black wire fr

The white wire from the fixture is connected to the white (neutral) wire

Tuck all connections neatly into junction box.

at fuse or circuit breaker box before installing or servicing any part of this

power supply wires are within

, use wire suitable for at least

turning it counter

(1) on the junction box by securing it with two

appropriate wire. Secure

from the fixture and power source to the green

LED Pendant Fixtures

-

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To

grounding, there must be a separate ground wire (green)

this fixture and the ground connection of your main power

This fixture is intended to be used for general

as shown in figure

installing or servicing

120VAC / 60Hz

This fixture is designed for use in a 110
Do not use on a dimming circuit.

120VAC, 60Hz fused circuit.

property damage.
It is re

electrical codes.

ASSEMBLY

1.
A.

fixture.
B.

2. Wiring­ Caution:

three inches of the ballast
(194F).
Note:
Consult a qualified elect
A. Loosen four

clockwise.

B. Pre-Install gem bar
screws (2) (supplied).
C.

electrician perform all wiring. This

wet or damp surface or in water.

the

power supply

emove gem bar (1) by

between
supply panel.

locations.

k

90C

ing gem bar

accomplish proper

contact

indoor lighting in damp

D. Re-

C. Make all wires
nuts (supplied).
D.
screw in the gem bar.
E.
power source.
F.
from power source.
G.

1 of 2

to the

with wire

s

om

8060745 R0

CENTRE LED PENDANTS

Models:

CNP3400 Series

AFX Lighting warrants this fixture is free from defects in materials and workmanship when installed and used under normal ope

of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it

misuse, mishandling or damage incurred in transit

(driver are not shown):

cables (6)

the same length. If any length adjustment is needed,

the fixture so the balance will be free hanging on the cables. Push the

in the direction of the arrow

The cables are pulled by the weight of the balance (5) until they are all the

Align the canopy (4) open slots with three gem bar screws (3)

Install the fixture by inserting

and turning canopy clockwise.

A. Thread in the glass shade (9)

shade style have the same thread.

power at fuse or circuit breaker box.

of LED Module.

Remove Diffuser (9) by turning it counter clockwise

and turn LED module (6) counter clockwise to remove it.

Insert new LED lamp into the lamp socket

the lamp snaps in

attached glass diffuser

between the canopy (4) and the

to even the cable lengt

metal insert into the lamp

The conical shade style is shown, all

cated in the housing

LED Pendant Fixtures

rating conditions for a period

does not cover failure due to improper installation,

3. Mounting

A.
Make sure all six
balance (5) are all

adjustment knob (11)

same length.

B.

the canopy
(4) open slots
Tighten the screws.

for each light

the head of the screws thru

120VAC / 60Hz

hold

h.

.

4. Shade Installation.

holder (7) and tighten it.

5. Restore

6. Replacement
A.
B. Hold the housing (7)
C.

clockwise until
D. Re-

Limited Factory Warranty

.

lo

(5) and turn it

place.

of 3 years from date

2 of 2

8060745 R0