AFX CNP240041LSNPWH User Manual
CENTRE LED PENDANTS
Models:
CNP2400 Series
Safety Precautions
Read all safety precautions and installation instructions carefully before
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
INSTRUCTIONS
Preparing for installation
Disconnect electrical power
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box.
power wires for damage or scrapes. If
wires are within three inches of
90C (194F).
Most dwellings built before 1985 have supply wire rated to
60C. Consult a qualified electr
screws (3) and r
plate
(supplied)
Mark two mounting holes locations on the ceiling
bar plate as a template. Remove the gem bar plate and drill two
)
install the gem bar plate (1) by securing it with two
(2) on the junction box and two screws
connections
Connect the green wire
in the gem bar
The black wire from the fixture is connected to the black
The white wire from the fixture is connected to the white
(neutral) wire from power source.
Tuck all connections neatly into junction box.
at fuse or circuit breaker box before installing or servicing any part of this
power supply
, use wire
shifting th
on box by securing it
by using gem
appropriate wire. Secure
from the fixture and power source to
LED Pendant Fixtures
-
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
this fixture and the ground connection of your main power
This fixture is intended to be used for general
as shown in figure
installing or servicing
120VAC / 60Hz
This fixture is designed for use in a 110
Do not use on a dimming circuit.
120VAC, 60Hz fused circuit.
property damage.
It is re
electrical codes.
ASSEMBLY
1.
A.
fixture.
B.
2. WiringCaution:
Check
suitable for at least
Note:
A. Loosen four
fixture along the slot.
B. Pre-Install gem bar
with two screws (2)
C.
electrician perform all wiring. This
wet or damp surface or in water.
the
the ballast power supply
ician before installing.
emove gem bar (1) by
(1) on the juncti
.
accomplish proper
contact
between
supply panel.
locations.
indoor lighting in wet
e
holes for the anchors (13
D. Re-
(supplied). Install the anchors.
screws
(14) on the ceiling.
C. Make all wires
to the
with
wire nuts (supplied).
D.
the green screw
E.
s
.
wire
from power source.
F.
G.
1 of 2
8060744 R0
CENTRE LED PENDANTS
Models:
CNP2400 Series
AFX Lighting warrants this fixture is free from defects in materials and workmanship when installed and used under normal ope
all component parts and extends only to replacement of defective fixture or components; it does not cover failure due to impr
installation, misuse, mishandling or damage incurred in transit
not shown)
cables (6)
the same length. If any length adjustment is needed,
fixture so the balance will be free hanging on the cables.
in the direction of the arrow
pulled by the weight of the balance (5) until they
Align the canopy (4) open slots with four gem bar screws (3
Install the fixture by inserting
and
Thread in the glass shade (9) metal insert into the lamp holder (7) and tighten it.
Restore power at fuse or circuit breaker box.
D Module.
Remove Diffuser (9) by turning it counter clockwise
and turn LED module (6) counter clockwise to remove it.
Insert new LED lamp into the lamp socket
(5) and turn it clockwise until
attached glass diffuser.
between the canopy (4) and the
Push the
ble length. The cables are
all the same length.
located in the
LED Pendant Fixtures
rating conditions for a period of 3 years from
3. Mounting
A. (drivers are
Make sure all six
balance (5) are all
knob (11)
.
B.
screws thru the
canopy (4) open slots
Tighten the screws.
4. Shade Installation.
A.
5.
6. Replacement of LE
A.
B. Hold the housing (7)
C.
housing
place.
D. Re-
:
for each light
to even the ca
are
the heads of the
shifting it until it stops.
the lamp snaps in
120VAC / 60Hz
hold the
adjustment
).
.
Limited Factory Warranty
date of purchase. This warranty covers
2 of 2
oper
8060744 R0
Loading...