AFX CNP140027LSNPWH User Manual
CENTRE LED PENDANTS
Models:
CNP1400 Series
Safety Precautions
Read all safety precautions and installation instructions carefully before
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
INSTRUCTIONS
Preparing for installation
Disconnect electrical power
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside
Make sure power is off at fuse or circuit
eck power wires for damage or
power supply wires are within three
power supply
Most dwellings built before 1985 have supply
wire rated to 60C. Consult a qualified ele
pre
by turning
Install gem bar on the juncti
(supplied)
connections
(supplied
Connect the green wire
power source to the green screw
The black wire from the fixture is connected to the
black wire from power source.
the fixture is connected to the
white (neutral) wire from power source.
Tuck all connections neatly into junction box.
at fuse or circuit breaker box before installing or servicing any part of this
LED Pendant Fixtures
-
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
this fixture and the ground connection of your main power
This fixture is intended to be used for general
as shown in figure
installing or servicing
120VAC / 60Hz
This fixture is designed for use in a 110
Do not use on a dimming circuit.
120VAC, 60Hz fused circuit.
property damage.
It is re
electrical codes.
ASSEMBLY
1.
A.
fixture.
B.
2. WiringÂjunction box.
Caution:
breaker box. Ch
scrapes. If the
inches of the ballast
for at least 90C (194F).
Note:
before installing.
A. Loosen screws (3)
and remove gem bar
clockwise.
B.
with two screws (2)
C. Make all wires
Secure with wire nuts
D.
E.
F. The white wire from
G.
1 of 2
electrician perform all wiring. This
wet or damp surface or in water.
, use wire suitable
ctrician
-installed on the gem bar (1)
it counter
on box by securing it
.
to the appropriate wire.
).
s from the fixture and
in the gem bar.
between
supply panel.
locations.
accomplish proper
contact
indoor lighting in damp
8060743 R0
CENTRE LED PENDANTS
Models:
CNP1400 Series
AFX Lighting warrants this fixture is free from defects in materials and workmanship when installed and used under normal ope
date of purchase. This warranty covers all component pa
installation, misuse, mishandling or damage incurred in transit
pulley
f any length adjustment
free hanging on the cables. Push the
he cables are pulled by the weight of the balance (5) until the
Align the canopy (4) open slots with
Install the fixture by inserting
and turning canopy clockwise. Tighten
A. Thread in the glass shade (9)
conical shade style is shown, all shade style have the same thread.
Restore power at fuse or circuit breaker box.
of LED Module.
emove Diffuser (9) by turning it counter clockwise
and turn
counter clockwise to remove it.
Insert new LED lamp into the lamp socket
5) and turn it clockwise until
attached glass diffuser.
rts and extends only to replacement of defective fixture or components; it does not cover failure due to improper
between the canopy (4) and the
hold the fixture so the balance will be
(11)
gem bar screws (3)
the
screws
metal insert into the lamp holder (7) and tighten it.
located in the
pla
LED Pendant Fixtures
rating conditions for a period of 3 years from
3. Mounting
A. Make sure all six
the same length. I
even the cable length. T
all the same length.
B.
(4) open slots
cables (6)
is needed,
adjustment knob
two
the head of the screws thru
120VAC / 60Hz
balance (5) are all
in the direction of the arrow to
y are
.
canopy
the
.
4. Shade Installation.
5.
6. Replacement
A. R
B. Hold the housing (7)
C.
housing (
D. Re-
LED module (6)
the lamp snaps in
The
.
ce.
Limited Factory Warranty
2 of 2
8060743 R0
Loading...