Aficio A292, A293, A292P, A293P Service Manual
(To be used in conjunction with A229 Service Manual)
RICOH GROUP COMPANIES
A292/A293
A292P/A293P
SERVICE MANUAL
000930MIU
®
®
A292/A293/A292P/A293P
SERVICE MANUAL
RICOH GROUP COMPANIES
A292/A293
A292P/A293P
SERVICE MANUAL
000930MIU
It is the reader's responsibility when discussing the information contained within this
document to maintain a level of confidentiality that is in the best interest of Ricoh
Corporation and its member companies.
NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY
FASHION AND DISTRIBUTED WITHOUT THE PRIOR
PERMISSION OF RICOH CORPORATION.
All product names, domain names or product illustrations, including desktop images,
used in this document are trademarks, registered trademarks or the property of their
respective companies.
They are used throughout this book in an informational or editorial fashion only and for
the benefit of such companies. No such use, or the use of any trade name, or web
site is intended to convey endorsement or other affiliation with Ricoh products.
2001 RICOH Corporation. All rights reserved.
WARNING
The Service Manual contains information
regarding service techniques, procedures,
processes and spare parts of office equipment
distributed by Ricoh Corporation. Users of this
manual should be either service trained or
certified by successfully completing a Ricoh
Technical Training Program.
Untrained and uncertified users utilizing
information contained in this service manual to
repair or modify Ricoh equipment risk personal
injury, damage to property or loss of warranty
protection.
Ricoh Corporation
LEGEND
PRODUCT CODE COMPANY
GESTETNER RICOH SAVIN
A292 3355 Aficio 551 2055DP
A293 3370 Aficio 700 2070DP
A292
w/G594 Controller
A293
w/G594 Controller
--
--
Aficio 551P
Aficio 700P
--
--
DOCUMENTATION HISTORY
REV. NO. DATE COMMENTS
* 5/2000 Original Printing
TABLE OF CONTENTS
COMPARISON BETWEEN A292/A293 AND A229
OVERALL INFORMATION
1. OVERALL MACHINE INFORMATION.........................................1-1
1.1 SPECIFICATIONS ....................................................................................1-1
1.1.1 COPIER ENGINE............................................................................. 1-1
1.1.2 ADF .................................................................................................. 1-4
1.2 MACHINE CONFIGURATION...................................................................1-5
1.3 MECHANICAL COMPONENT LAYOUT ...................................................1-6
1.3.1 COPIER ENGINE............................................................................. 1-6
1.3.2 ADF .................................................................................................. 1-8
1.4 PAPER PATH............................................................................................1-9
1.5 COPY PROCESS....................................................................................1-10
1.6 DRIVE LAYOUT ......................................................................................1-12
1.6.1 COPIER ENGINE........................................................................... 1-12
1.6.2 ADF ................................................................................................ 1-13
1.7 ELECTRICAL COMPONENT DESCRIPTION.........................................1-14
1.7.1 COPIER ENGINE........................................................................... 1-14
1.7.2 ADF ................................................................................................ 1-20
DETAILED DESCRIPTIONS
2. DETAILED DESCRIPTIONS........................................................2-1
2.1 DOCUMENT FEEDER .............................................................................. 2-1
2.1.1 PICK-UP ROLLER RELEASE ..........................................................2-1
2.1.2 BOTTOM PLATE LIFT .....................................................................2-2
2.1.3 PICK-UP AND SEPARATION ..........................................................2-3
2.1.4 ORIGINAL FEED.............................................................................. 2-4
2.1.5 ORIGINAL SIZE DETECTION..........................................................2-5
Original Length .....................................................................................2-5
Original Width ....................................................................................... 2-5
2.1.6 ORIGINAL TRANSPORT ................................................................. 2-6
2.1.7 ORIGINAL SKEW CORRECTION.................................................... 2-7
2.1.8 ORIGINAL INVERSION AND FEED-OUT........................................2-8
General Operation ................................................................................2-8
Original Inversion.................................................................................. 2-9
Original Exit (Single-Sided Original Mode) .........................................2-10
Original Exit (Double-Sided Original Mode) ........................................ 2-11
SM i A292/A293
2.1.9 JAM CONDITIONS.........................................................................2-12
Feed-in ...............................................................................................2-12
Feed-out .............................................................................................2-12
Inversion .............................................................................................2-12
2.2 SCANNING .............................................................................................2-13
2.2.1 OVERVIEW ....................................................................................2-13
2.2.2 SCANNER DRIVE.......................................................................... 2-14
2.2.3 ORIGINAL SIZE DETECTION IN BOOK MODE ............................2-15
2.3 IMAGE PROCESSING............................................................................ 2-16
2.3.1 OVERVIEW ....................................................................................2-16
2.3.2 SBU................................................................................................2-17
2.3.3 AUTO IMAGE DENSITY (ADS)...................................................... 2-18
2.3.4 IPU (IMAGE PROCESSING UNIT) ................................................2-19
2.3.5 IMAGE PROCESSING STEPS AND RELATED SP MODES ........ 2-20
2.3.6 AUTO SHADING ............................................................................ 2-25
Black Level Correction........................................................................2-25
White Level Correction .......................................................................2-25
2.3.7 BACKGROUND ERASE.................................................................2-26
2.3.8 INDEPENDENT DOT ERASE ........................................................2-27
2.3.9 FILTERING, MAIN SCAN MAGNIFICATION/REDUCTION ...........2-28
Overview............................................................................................. 2-28
Filtering............................................................................................... 2-28
Main Scan Magnification/Reduction....................................................2-29
Sub Scan Magnification...................................................................... 2-29
2.3.10 GAMMA (γ) CORRECTION.......................................................... 2-30
2.3.11 GRADATION PROCESSING .......................................................2-30
Three-graduation Processing ............................................................. 2-30
Four-graduation Processing ...............................................................2-31
Error Diffusion and Dithering ..............................................................2-31
2.3.12 LINE WIDTH CORRECTION........................................................ 2-31
2.4 LASER EXPOSURE................................................................................2-32
2.4.1 AUTO POWER CONTROL ............................................................2-32
2.4.2 DUAL BEAM WRITING .................................................................. 2-33
2.4.3 LASER BEAM PITCH CHANGE MECHANISM..............................2-34
2.4.4 LD SAFETY SWITCHES................................................................ 2-35
2.5 DRUM UNIT ............................................................................................2-36
2.5.1 PROCESS CONTROL ...................................................................2-36
Overview............................................................................................. 2-36
Drum potential sensor calibration .......................................................2-37
VSG adjustment..................................................................................2-37
VG Adjustment ...................................................................................2-38
LD power adjustment.......................................................................... 2-39
Toner Density Adjustment ..................................................................2-39
VREF Update .....................................................................................2-40
2.5.2 DRUM UNIT COMPONENTS......................................................... 2-41
2.5.3 DRUM CHARGE ............................................................................2-42
Overview............................................................................................. 2-42
Charge Corona Wire Cleaning Mechanism ........................................2-43
A292/A293 ii SM
2.5.4 DRUM CLEANING AND TONER RECYCLING..............................2-44
Overview............................................................................................. 2-44
Drive Mechanism................................................................................ 2-45
Cleaning Blade Pressure Mechanism and Side-to-Side Movement ...2-46
2.5.5 OTHERS ........................................................................................2-47
Air Flow Around the Drum .................................................................. 2-47
Pick-off Mechanism ............................................................................2-48
2.6 DEVELOPMENT AND TONER SUPPLY ................................................2-49
2.6.1 OVERVIEW ....................................................................................2-49
2.6.2 DEVELOPMENT MECHANISM......................................................2-50
2.6.3 DEVELOPMENT BIAS ................................................................... 2-51
2.6.4 TONER DENSITY CONTROL........................................................ 2-52
Overview............................................................................................. 2-52
Sensor control mode...........................................................................2-52
Image pixel count control.................................................................... 2-53
2.6.5 TONER END DETECTION............................................................. 2-54
Toner Near End .................................................................................. 2-54
Toner End........................................................................................... 2-54
2.6.6 TONER END RECOVERY .............................................................2-54
2.6.7 ABNORMAL TD AND ID SENSOR CONDITIONS ......................... 2-55
2.7 IMAGE TRANSFER AND PAPER SEPARATION................................... 2-56
2.7.1 IMAGE TRANSFER AND PAPER SEPARATION MECHANISM ... 2-56
2.7.2 TRANSFER BELT UNIT LIFT MECHANISM.................................. 2-57
2.7.3 TRANSFER BELT CLEANING MECHANISM................................ 2-58
2.8 PAPER FEED..........................................................................................2-59
2.8.1 OVERVIEW ....................................................................................2-59
2.8.2 DRIVE MECHANISM......................................................................2-60
2.8.3 TANDEM LCT – TRAY 1................................................................ 2-61
Overview............................................................................................. 2-61
Connecting the Left and Right Sides of the Tray ................................2-62
Paper Lift/Remaining Paper Detection................................................ 2-63
Fence Drive ........................................................................................2-65
Rear Fence Drive................................................................................2-66
Tray Positioning.................................................................................. 2-67
2.8.4 TRAY POSITIONING MECHANISM – TRAYS 1 TO 3...................2-68
2.8.5 PAPER LIFT MECHANISM - TRAYS 2 AND 3............................... 2-69
2.8.6 VERTICAL TRANSPORT MECHANISM........................................ 2-70
2.8.7 PAPER REGISTRATION ...............................................................2-71
2.8.8 PAPER SIZE DETECTION – TRAY 2 ............................................ 2-72
2.9 IMAGE FUSING ...................................................................................... 2-73
2.9.1 OVERVIEW ....................................................................................2-73
2.9.2 FUSING ENTRANCE GUIDE......................................................... 2-74
2.9.3 FUSING DRIVE MECHANISM .......................................................2-75
2.10 PAPER EXIT/DUPLEX..........................................................................2-76
2.10.1 OVERVIEW ..................................................................................2-76
2.10.2 INVERTER ...................................................................................2-77
Feed-in and Jogging........................................................................... 2-77
Feed-out .............................................................................................2-78
2.10.3 DUPLEX TRAY FEED MECHANISM ........................................... 2-79
SM iii A292/A293
Rev. 11/2000
2.10.4 BASIC DUPLEX FEED OPERATION...........................................2-80
Longer than A4 / Letter lengthwise .....................................................2-80
2.11 ENERGY SAVER MODES ....................................................................2-83
2.11.1 LOW POWER MODE ...................................................................2-83
Entering low power mode ...................................................................2-83
What happens in low power mode ......................................................2-83
Return to stand-by mode ....................................................................2-83
INSTALLATION
3. INSTALLATION PROCEDURE ................................................... 3-1
3.1 INSTALLATION REQUIREMENTS ...........................................................3-1
3.1.1 ENVIRONMENT ...............................................................................3-1
3.1.2 MACHINE LEVEL.............................................................................3-1
3.1.3 MINIMUM SPACE REQUIREMENTS...............................................3-2
3.1.4 POWER REQUIREMENTS ..............................................................3-2
3.2 COPIER (A229/A293)................................................................................3-3
3.1.1 ACCESSORY CHECK......................................................................3-3
3.1.2 INSTALLATION PROCEDURE ........................................................3-4
3.3 LCT (A698)..............................................................................................3-14
3.3.1 ACCESSORY CHECK....................................................................3-14
3.3.2 INSTALLATION PROCEDURE ......................................................3-15
3.4 3,000-SHEET FINISHER (B312).............................................................3-20
3.4.1 ACCESSORY CHECK....................................................................3-20
3.4.2 INSTALLATION PROCEDURE ......................................................3-21
3.5 PUNCH UNIT INSTALLATION (A812) FOR B312 FINISHER.................3-24
3.5.1 ACCESSORY CHECK....................................................................3-24
3.5.2 PUNCH UNIT INSTALLATION .......................................................3-25
3.6 FINISHER (B302) ....................................................................................3-28
3.6.1 INSTALLATION PROCEDURE ......................................................3-28
3.7 PUNCH UNIT INSTALLATION (A812) FOR B302 FINISHER.................3-31
3.7.1 ACCESSORY CHECK....................................................................3-31
3.1.2 PUNCH UNIT INSTALLATION .......................................................3-32
3.8 KEY COUNTER INSTALLATION ............................................................3-35
3.9 COPY CONNECTOR KIT INSTALLATION .............................................3-36
3.10 COPY TRAY TYPE 700 INSTALLATION ..............................................3-39
SERVICE TABLES
4. SERVICE TABLES...................................................................... 4-1
4.1 GENERAL CAUTIONS..............................................................................4-1
4.1.1 DRUM...............................................................................................4-1
4.1.2 DRUM UNIT......................................................................................4-1
4.1.3 TRANSFER BELT UNIT ...................................................................4-2
4.1.4 SCANNER UNIT...............................................................................4-2
4.1.5 LASER UNIT.....................................................................................4-2
4.1.6 CHARGE CORONA..........................................................................4-3
A292/A293 iv SM
4.1.7 DEVELOPMENT ..............................................................................4-3
4.1.8 CLEANING .......................................................................................4-4
4.1.9 FUSING UNIT...................................................................................4-4
4.1.10 PAPER FEED................................................................................. 4-4
4.1.11 USED TONER................................................................................ 4-4
4.2 SERVICE PROGRAM MODE ................................................................... 4-5
4.2.1 SERVICE PROGRAM MODE OPERATION .................................... 4-5
Service Program Access Procedure..................................................... 4-5
Accessing Copy Mode from within an SP Mode ...................................4-7
Selecting the Program Number ............................................................4-8
Inputting a Value or Setting for an SP Mode......................................... 4-9
4.2.2 SERVICE PROGRAM MODE TABLES.......................................... 4-10
4.2.3 TEST PATTERN PRINTING (SP2-902) ......................................... 4-66
Test Pattern Table (SP2-902-2: Test Pattern Printing – IPU) .............4-66
Test Pattern Table (SP2-902-3: Test Pattern Printing – Printing) ....... 4-66
4.2.4 INPUT CHECK ............................................................................... 4-67
Main Machine Input Check (SP5-803)................................................ 4-67
ADF Input Check (SP6-007) ...............................................................4-71
4.2.5 OUTPUT CHECK ........................................................................... 4-72
Main Machine Output Check (SP5-804) .............................................4-72
ADF Output Check (SP6-008) ............................................................ 4-73
4.2.6 SYSTEM PARAMETER AND DATA LISTS (SMC LISTS) .............4-73
4.2.7 MEMORY ALL CLEAR (SP5-801).................................................. 4-74
4.2.8 SOFTWARE RESET ...................................................................... 4-75
4.2.9 SYSTEM SETTING AND COPY SETTING (UP MODE) RESET ... 4-75
System Setting Reset ......................................................................... 4-75
Copy Features Reset.......................................................................... 4-75
4.3 PROGRAM AND DATA DOWNLOAD.....................................................4-76
4.3.1 OVERVIEW ....................................................................................4-76
4.3.2 DOWNLOADING SOFTWARE FROM FLASH ROM TO THE BIC 4-76
4.3.3 DOWNLOAD THE BICU SOFTWARE FROM BICU TO FLASH
MEMORY CARD ...................................................................................... 4-78
4.3.4 DOWNLOAD NVRAM DATA TO THE BICU ..................................4-79
4.3.5 DOWNLOAD NVRAM DATA FROM BICU TO FLASH MEMORY
CARD .......................................................................................................4-80
4.3.6 DOWNLOAD STAMP DATA TO THE BICU ...................................4-81
4.4 USER PROGRAM MODE ....................................................................... 4-82
4.4.1 HOW TO ENTER AND EXIT UP MODE ........................................ 4-82
4.4.2 UP MODE TABLE ..........................................................................4-82
System Setting Table..........................................................................4-82
Copy Features Table .......................................................................... 4-83
4.4.3 IMAGE QUALITY SETTING BY UP MODE....................................4-87
Text Mode........................................................................................... 4-87
Text/Photo Mode ................................................................................4-91
Photo Mode ........................................................................................4-92
Pale Mode ..........................................................................................4-93
Generation Mode................................................................................ 4-93
4.5 TEST POINTS/DIP SWITCHES/LEDS....................................................4-94
4.5.1 DIP SWITCHES..............................................................................4-94
SM v A292/A293
Rev. 10/2001
4.5.2 TEST POINTS ................................................................................4-94
4.5.3 FUSES............................................................................................4-95
4.5.4 VARIABLE RESISTORS ................................................................4-96
4.5.5 LEDS ..............................................................................................4-96
4.6 SPECIAL TOOLS AND LUBRICANTS....................................................4-96
4.6.1 SPECIAL TOOLS ...........................................................................4-96
4.6.2 LUBRICANTS.................................................................................4-96
4.7 FIRMWARE HISTORY . ...........................................................................4-98
PREVENTIVE MAINTENANCE
5. PREVENTIVE MAINTENANCE SCHEDULE .............................. 5-1
5.1 PM TABLE.................................................................................................5-1
5.2 PM COUNTER ..........................................................................................5-5
REPLACEMENT AND ADJUSTMENT
6. REPLACEMENT AND ADJUSTMENT........................................ 6-1
6.1 EXTERIOR ................................................................................................6-1
6.1.1 FILTERS...........................................................................................6-1
Ozone Filter: Duct.................................................................................6-1
Filter Vacuum........................................................................................6-1
6.2 DOCUMENT FEEDER ..............................................................................6-2
6.2.1 COVER REMOVAL ..........................................................................6-2
6.2.2 FEED UNIT REMOVAL AND SEPARATION ROLLER
REPLACEMENT................................................................................6-4
6.2.3 FEED BELT REPLACEMENT ..........................................................6-5
6.2.4 PICK-UP ROLLER REPLACEMENT................................................6-6
6.2.5 SENSOR REPLACEMENT...............................................................6-7
Entrance and Registration Sensors ......................................................6-7
Width Sensor ........................................................................................6-8
Exit Sensor and Inverter Sensor...........................................................6-9
6.2.6 TRANSPORT BELT REPLACEMENT............................................6-10
6.3 SCANNER UNIT......................................................................................6-11
6.3.1 EXPOSURE GLASS.......................................................................6-11
6.3.2 LENS BLOCK .................................................................................6-12
6.3.3 ORIGINAL SIZE SENSORS ...........................................................6-13
6.3.4 EXPOSURE LAMP .........................................................................6-14
6.3.5 SCANNER MOTOR / MCU.............................................................6-15
Scanner Motor ....................................................................................6-15
MCU....................................................................................................6-15
6.3.6 SCANNER WIRES .........................................................................6-16
Rear Scanner Drive Wire....................................................................6-19
Front Scanner Drive Wire ...................................................................6-20
Reinstallation ......................................................................................6-21
6.4 LASER UNIT ...........................................................................................6-23
6.4.1 CAUTION DECAL LOCATIONS.....................................................6-23
6.4.2 LD UNIT REPLACEMENT..............................................................6-24
A292/A293 vi SM
6.4.3 POLYGON MIRROR MOTOR REPLACEMENT ............................6-25
6.5 DRUM UNIT ............................................................................................6-26
6.5.1 DRUM ENTRANCE SEAL AND DRUM POTENTIAL SENSOR
REPLACEMENT ......................................................................................6-26
6.5.2 DRUM MOTOR REPLACEMENT...................................................6-27
6.5.3 TONER OUTPUT AND RECYCLING PUMP UNIT
REPLACEMENT .............................................................................6-28
6.6 DEVELOPMENT AND TONER SUPPLY ................................................6-30
6.6.1 DEVELOPMENT AND AIR DUST FILTER REPLACEMENT......... 6-30
6.6.2 DEVELOPER REPLACEMENT......................................................6-31
6.6.3 TONER END SENSOR REPLACEMENT ......................................6-33
6.6.4 DEVELOPMENT MOTOR REPLACEMENT .................................. 6-33
6.7 TRANSFER BELT UNIT.......................................................................... 6-34
6.7.1 TRANSFER BELT UNIT REMOVAL/INSTALLATION .................... 6-34
- Removal - ......................................................................................... 6-34
- Installation - ...................................................................................... 6-34
6.8 PAPER FEED..........................................................................................6-36
6.8.1 PAPER TRAY REMOVAL .............................................................. 6-36
Tandem Tray Removal ....................................................................... 6-36
6.8.2 REAR FENCE RETURN SENSOR REPLACEMENT.....................6-38
6.8.3 REAR FENCE HP SENSOR REPLACEMENT...............................6-39
6.8.4 BOTTOM PAPER SENSOR REPLACEMENT ...............................6-40
6.8.5 BOTTOM PLATE LIFT WIRE REPLACEMENT .............................6-41
6.8.6 TANDEM LCT PAPER SIZE CHANGE .......................................... 6-43
6.8.7 BY-PASS PAPER SIZE BOARD REPLACEMENT ........................6-46
6.8.8 PAPER FEED CLUTCH/RELAY CLUTCH REMOVAL...................6-48
6.8.9 BY-PASS FEED MOTOR/CLUTCH REMOVAL .............................6-51
6.8.10 REGISTRATION MOTOR REMOVAL.......................................... 6-52
6.8.11 PAPER TRAY UNIT REMOVAL................................................... 6-53
6.9 FUSING UNIT .........................................................................................6-54
6.9.1 FUSING UNIT REMOVAL ..............................................................6-54
6.9.2 FUSING THERMISTOR AND FUSING THERMOFUSE
REPLACEMENT .............................................................................6-55
Fusing Thermistor Replacement.........................................................6-55
Fusing Thermofuse Replacement.......................................................6-55
6.9.3 FUSING LAMP REPLACEMENT ...................................................6-56
6.9.4 HOT ROLLER REPLACEMENT..................................................... 6-57
6.9.5 OIL SUPPLY/CLEANING ROLLER REPLACEMENT .................... 6-59
6.9.6 PRESSURE ROLLER CLEANING ROLLER REPLACEMENT ......6-60
6.9.7 MAGNET POSITION ADJUSTMENT............................................. 6-61
6.10 PAPER EXIT/DUPLEX UNIT.................................................................6-62
6.10.1 1ST AND 2ND EXIT SENSOR .....................................................6-62
6.10.2 JOGGER MOTOR........................................................................ 6-63
6.10.3 DUPLEX ENTRANCE SENSOR ..................................................6-63
6.10.4 DUPLEX TRANSPORT/DUPLEX FEED CLUTCHES .................. 6-64
6.10.5 DUPLEX TRANSPORT SENSOR 1............................................. 6-64
6.10.6 DUPLEX TRANSPORT SENSORS 2 & 3 ....................................6-65
6.10.7 INVERTER EXIT CLUTCH...........................................................6-66
6.10.8 DUPLEX INVERTER SENSOR.................................................... 6-66
SM vii A292/A293
Rev. 08/2000
6.11 BOARDS AND OTHER ITEMS .............................................................6-67
6.11.1 BICU BOARD ...............................................................................6-67
6.11.2 I/O BOARD ...................................................................................6-68
6.11.3 PSU ..............................................................................................6-69
6.11.4 PAPER FEED CONTROL BOARD (PFC) ....................................6-69
6.12 COPY IMAGE ADJUSTMENTS: PRINTING/SCANNING......................6-70
6.12.1 PRINTING.....................................................................................6-70
Registration - Leading Edge ...............................................................6-70
Registration – Side-to-Side.................................................................6-70
Tray 1..................................................................................................6-71
Tray 2..................................................................................................6-71
Tray 3..................................................................................................6-72
By-pass Tray.......................................................................................6-72
6.13 TOUCH SCREEN CALIBRATION .........................................................6-73
TROUBLESHOOTING
7. TROUBLESHOOTING ................................................................ 7-1
7.1 SERVICE CALL CONDITIONS .................................................................7-1
7.1.1 SUMMARY .......................................................................................7-1
7.1.2 SC CODE DESCRIPTIONS .............................................................7-2
7.2 ELECTRICAL COMPONENT DEFECTS.................................................7-40
7.2.1 SENSORS ......................................................................................7-40
7.2.2 SWITCHES.....................................................................................7-44
7.3 BLOWN FUSE CONDITIONS .................................................................7-45
3,000-SHEET FINISHER B302
1. OVERALL MACHINE INFORMATION ........................................ 8-1
1.1 SPECIFICATIONS.....................................................................................8-1
1.2 MECHANICAL COMPONENT LAYOUT....................................................8-3
1.3 ELECTRICAL COMPONENT DESCRIPTION...........................................8-4
1.4 DRIVE LAYOUT ........................................................................................8-6
2. DETAILED DESCRIPTIONS ....................................................... 8-7
2.1 TRAY AND STAPLER JUNCTION GATE .................................................8-7
Upper Tray Mode..................................................................................8-7
Sort/Stack Mode ...................................................................................8-7
Staple Mode..........................................................................................8-7
2.2 PAPER PRE-STACKING...........................................................................8-8
2.3 JOGGER UNIT PAPER POSITIONING.....................................................8-9
Vertical Paper Alignment ......................................................................8-9
Horizontal Paper Alignment ..................................................................8-9
Paper Stack Correction.........................................................................8-9
A292/A293 viii SM
2.4 STAPLER UNIT MOVEMENT................................................................. 8-10
Side-to-Side........................................................................................ 8-10
Rotation (1)......................................................................................... 8-11
Rotation (2)......................................................................................... 8-11
2.5 STAPLER................................................................................................ 8-12
2.6 FEED-OUT.............................................................................................. 8-14
2.7 SHIFT TRAY UP/DOWN MOVEMENT ...................................................8-15
2.8 SHIFT TRAY SIDE-TO-SIDE MOVEMENT............................................. 8-16
2.9 PUNCH UNIT DRIVE ..............................................................................8-17
2.10 PUNCH WASTE COLLECTION............................................................ 8-18
2.11 JAM CONDITIONS................................................................................ 8-19
3. SERVICE TABLES .................................................................... 8-20
3.1 DIP SWITCHES ......................................................................................8-20
3.2 TEST POINTS.........................................................................................8-20
3.3 FUSES ....................................................................................................8-20
4. REPLACEMENT AND ADJUSTMENT ...................................... 8-21
4.1 COVER REPLACEMENT........................................................................ 8-21
Front Door ..........................................................................................8-21
Left Inner Cover.................................................................................. 8-21
Inner Cover......................................................................................... 8-21
Table................................................................................................... 8-22
Upper Tray.......................................................................................... 8-22
Left Upper Cover ................................................................................8-22
Left Lower Cover ................................................................................8-22
Upper Cover .......................................................................................8-22
Rear Cover .........................................................................................8-22
Shift Tray ............................................................................................8-23
Front Shift Tray Cover ........................................................................8-23
Rear Shift Tray Cover......................................................................... 8-23
4.2 POSITIONING ROLLER REPLACEMENT.............................................. 8-24
4.3 ALIGNMENT BRUSH ROLLER REPLACEMENT................................... 8-25
4.4 SENSOR REPLACEMENT .....................................................................8-26
4.4.1 STACK HEIGHT 1, 2 AND EXIT GUIDE OPEN SENSOR ............. 8-26
Stack Height Sensors 1 and 2 ............................................................ 8-26
Exit Guide Open Sensor..................................................................... 8-26
4.4.2 UPPER TRAY PAPER LIMIT AND EXIT SENSOR........................ 8-27
Upper Tray Paper Limit Sensor ..........................................................8-27
Upper Tray Exit Sensor ......................................................................8-27
4.4.3 SHIFT TRAY EXIT SENSOR..........................................................8-28
4.4.4 ENTRANCE AND STAPLER TRAY ENTRANCE SENSORS ........ 8-29
Entrance Sensor................................................................................. 8-29
Stapler Tray Entrance Sensor ............................................................ 8-29
4.4.5 PRE-STACK STOPPER SENSOR................................................. 8-30
4.4.6 STAPLE WASTE HOPPER SENSOR............................................ 8-31
SM ix A292/A293
4.4.7 STAPLER ROTATION HP AND STAPLER RETURN
SENSORS....................................................................................... 8-32
Stapler Rotation HP Sensor................................................................8-32
Stapler Return Sensor ........................................................................ 8-32
4.5 STAPLER REMOVAL .............................................................................8-33
4.6 PUNCH POSITION ADJUSTMENT ........................................................8-34
Right to Left ........................................................................................8-34
Front to Rear ......................................................................................8-34
3,000-SHEET FINISHER B312
1. OVERALL MACHINE INFORMATION.........................................9-1
1.1 SPECIFICATIONS ....................................................................................9-1
1.2 ELECTRICAL COMPONENT LAYOUT.....................................................9-4
1.3 ELECTRICAL COMPONENT DESCRIPTION...........................................9-6
1.4 MECHANICAL COMPONENT LAYOUT ...................................................9-8
1.5 DRIVE LAYOUT ........................................................................................9-9
2. DETAILED DESCRIPTIONS......................................................9-10
2.1 TRAY AND STAPLER JUNCTION GATE MECHANISM ........................9-10
Upper tray mode................................................................................. 9-10
Sort/stack mode.................................................................................. 9-10
Staple mode .......................................................................................9-10
2.2 PRE-STACK MECHANISM..................................................................... 9-11
2.3 JOGGER UNIT PAPER POSITIONING MECHANISM ...........................9-12
Vertical Paper Alignment .................................................................... 9-12
Horizontal Paper Alignment................................................................ 9-12
2.4 STAPLER UNIT MOVEMENT MECHANISM .......................................... 9-13
Side-to-side: .......................................................................................9-13
Rotation: .............................................................................................9-13
2.5 STAPLER................................................................................................ 9-14
2.6 FEED-OUT MECHANISM ....................................................................... 9-15
2.7 SHIFT TRAY UP/DOWN MECHANISM ..................................................9-16
2.8 SHIFT TRAY SIDE-TO-SIDE MECHANISM............................................9-17
2.9 PUNCH UNIT DRIVE MECHANISM .......................................................9-18
2.10 PUNCH WASTE COLLECTION MECHNISM........................................9-19
2.11 JAM CONDITIONS................................................................................ 9-20
3. SERVICE TABLES .................................................................... 9-21
3.1 DIP SWITCHES ......................................................................................9-21
3.2 TEST POINTS.........................................................................................9-21
3.3 FUSES ....................................................................................................9-21
4. REPLACEMENT AND ADJUSTMENT ...................................... 9-22
4.1 COVER REPLACEMENT........................................................................ 9-22
Rear Cover .........................................................................................9-22
Upper Left Cover ................................................................................9-22
A292/A293 x SM
Upper Cover .......................................................................................9-22
Front Door ..........................................................................................9-22
Left Front Cover.................................................................................. 9-22
Shift Tray ............................................................................................9-23
Lower Left Cover ................................................................................9-23
Right Cover......................................................................................... 9-23
Front Shift Tray Cover ........................................................................9-23
Rear Shift Tray Cover......................................................................... 9-23
4.2 POSITIONING ROLLER REPLACEMENT.............................................. 9-24
4.3 ALIGNMENT BRUSH ROLLER REPLACEMENT................................... 9-25
4.4 SENSOR REPLACEMNT........................................................................ 9-26
4.4.1 STACK HEIGHT SENSOR 1 AND 2 ..............................................9-26
4.4.2 UPPER TRAY PAPER LIMIT AND EXIT SENSOR........................ 9-27
Upper Tray Paper Limit Sensor ..........................................................9-27
Upper Tray Exit Sensor ......................................................................9-27
4.4.3 SHIFT TRAY EXIT SENSOR..........................................................9-28
4.4.4 ENTRANCE AND STAPLER TRAY ENTRANCE SENSOR...........9-29
Entrance Sensor................................................................................. 9-29
Stapler Tray Entrance Sensor ............................................................ 9-29
4.4.5 STAPLER ROTATION HP SENSOR..............................................9-30
4.5 STAPLER REMOVAL .............................................................................9-31
4.6 PUNCH POSITION ADJUSTMENT ........................................................9-32
Right to left .........................................................................................9-32
Front to rear........................................................................................ 9-32
BOOKLET FINISHER A763
1. OVERALL MACHINE INFORMATION....................................... 10-1
1.1 SPECIFICATIONS ..................................................................................10-1
1.2 ELECTRICAL COMPONENT DESCRIPTION.........................................10-3
1.3 MECHANICAL COMPONENT LAYOUT .................................................10-6
2. DETAILED DESCRIPTIONS......................................................10-7
2.1 JUNCTION GATE MECHANISM.............................................................10-7
2.1.1 SHIFT TRAY MODE....................................................................... 10-7
A4/LT sideways or shorter.................................................................. 10-7
Longer than A4 sideways ...................................................................10-7
2.1.2 PROOF TRAY MODE ....................................................................10-8
2.1.3 BOOKLET STITCH MODE.............................................................10-8
2.2 PRE-STACK MECHANISM..................................................................... 10-9
2.3 PAPER SHIFT MECHANISM................................................................ 10-10
2.4 PAPER POSITIONING MECHANISM...................................................10-11
2.5 STAPLER UNIT MOVEMENT MECHANISM ........................................ 10-12
2.5.1 DRIVE ..........................................................................................10-12
2.5.2 MOVEMENT................................................................................. 10-12
Front and Rear Stapling....................................................................10-12
Tow-position Stapling .......................................................................10-12
SM xi A292/A293
2.6 STAPLER.............................................................................................. 10-13
2.7 SHIFT TRAY MECHANISM...................................................................10-14
2.8 BOOKLET UNIT GATE MECHANISM ..................................................10-15
2.9 RELAY ROLLER AND POSITIONING PLATE MECHANISM ...............10-17
2.10 POSITIONING ROLLER MECHANISM............................................... 10-18
2.11 BOOKLET UNIT JOGGER MOVEMENT MECHANISM......................10-19
2.12 BOOKLET STAPLER UNIT................................................................. 10-20
2.13 PAPER FOLDER MECHANISM.......................................................... 10-21
3. INSTALLATION ....................................................................... 10-23
3.1 ACCESSORY CHECK .........................................................................10-23
3.2 INSTALLATION PROCEDURE............................................................ 10-24
4. REPLACEMENT AND ADJUSTMENT .................................... 10-29
4.1 REMOVAL............................................................................................. 10-29
4.1.1 UPPER DOOR .............................................................................10-29
4.1.2 UPPER REAR COVER ................................................................10-30
4.1.3 LOWER REAR COVER................................................................10-30
4.1.4 TOP COVER ................................................................................10-31
4.1.5 UPPER INNER COVER ............................................................... 10-31
4.1.6 SHIFT TRAY UNIT ....................................................................... 10-32
4.1.7 UPPER SHIFT GUIDE ................................................................. 10-33
4.1.8 LOWER SHIFT GUIDE.................................................................10-33
4.1.9 EXIT UNIT ....................................................................................10-34
4.1.10 BUFFER ROLLER UNIT ............................................................10-35
4.1.11 STAPLER ...................................................................................10-36
4.1.12 FINISHER BOARD.................................................................... 10-37
4.1.13 BOOKLET UNIT ......................................................................... 10-38
4.1.14 FOLDER ROLLERS ................................................................... 10-40
4.1.15 FOLDER PLATE.........................................................................10-43
Removal ...........................................................................................10-43
Reinstalling ....................................................................................... 10-44
4.1.16 BOOKLET STAPLER UNIT........................................................10-45
Removal ...........................................................................................10-45
Adjustment........................................................................................ 10-46
4.1.17 BOOKLET BOARD..................................................................... 10-48
4.1.18 POSITIONING PLATE UNIT ...................................................... 10-48
4.1.19 1ST AND 2ND BOOKLET UNIT GATES ....................................10-49
4.2 ADJUSTMENT ...................................................................................... 10-50
4.2.1 SHIFT TRAY HEIGHT.................................................................. 10-50
4.2.2 JOGGER FENCE POSITION .......................................................10-51
4.2.3 STAPLING POSITOIN..................................................................10-52
4.2.4 BOOKLET STAPLING POSITION................................................ 10-53
A292/A293 xii SM
COPIER CONNECTION KIT B322
1. SPECIFICATIONS ..................................................................... 11-1
2. DETAILED DESCRIPTIONS......................................................11-2
2.1 OVERVIEW............................................................................................. 11-2
2.2 BASIC OPERATION ...............................................................................11-3
2.2.1 NO SORT AND NO STAPLE MODE.............................................. 11-3
2.2.2 SORT, STAPLE MODE.................................................................. 11-4
2.2.3 OPERATION IN IRREGULAR CONDITIONS ................................11-5
Paper end during copying ...................................................................11-5
Copy tray full....................................................................................... 11-5
Paper jam ...........................................................................................11-5
LG KIT B375
1. LG KIT B375..............................................................................12-1
1.1 ACCESSORY CHECK ............................................................................12-1
1.2 INSTALLATION PROCEDURE ...............................................................12-2
SM xiii A292/A293
!
IMPORTANT SAFETY NOTICES
PREVENTION OF PHYSICAL INJURY
1. Before disassembling or assembling parts of the copier and peripherals,
make sure that the copier power cord is unplugged.
2. The wall outlet should be near the copier and easily accessible.
3. Note that some components of the copier and the paper tray unit are
supplied with electrical voltage even if the main power switch is turned off.
4. If any adjustment or operation check has to be made with exterior covers off
or open while the main switch is turned on, keep hands away from electrified
or mechanically driven components.
5. If the Start key is pressed before the copier completes the warm-up period
(the Start key starts blinking red and green alternatively), keep hands away
from the mechanical and the electrical components as the copier starts
making copies as soon as the warm-up period is completed.
6. The inside and the metal parts of the fusing unit become extremely hot while
the copier is operating. Be careful to avoid touching those components with
your bare hands.
HEALTH SAFETY CONDITIONS
1. Never operate the copier without the ozone filters installed.
2. Always replace the ozone filters with the specified ones at the specified
intervals.
3. Toner and developer are non-toxic, but if you get either of them in your eyes
by accident, it may cause temporary eye discomfort. Try to remove with eye
drops or flush with water as first aid. If unsuccessful, get medical attention.
OBSERVANCE OF ELECTRICAL SAFETY STANDARDS
1. The copier and its peripherals must be installed and maintained by a
customer service representative who has completed the training course on
those models.
2. The NVRAM on the system control board has a lithium battery which can
explode if replaced incorrectly. Replace the NVRAM only with an identical
one. The manufacturer recommends replacing the entire NVRAM. Do not
recharge or burn this battery. Used NVRAM must be handled in accordance
with local regulations.
1
1. SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL
Do not incinerate toner bottles or used toner. Toner dust may ignite
suddenly when exposed to an open flame.
2. Dispose of used toner, developer, and organic photoconductors in
accordance with local regulations. (These are non-toxic supplies.)
3. Dispose of replaced parts in accordance with local regulations.
4. When keeping used lithium batteries in order to dispose of them later, do not
put more than 100 batteries per sealed box. Storing larger numbers or not
sealing them apart may lead to chemical reactions and heat build-up.
LASER SAFETY
The Center for Devices and Radiological Health (CDRH) prohibits the repair of
laser-based optical units in the field. The optical housing unit can only be repaired
in a factory or at a location with the requisite equipment. The laser subsystem is
replaceable in the field by a qualified Customer Engineer. The laser chassis is not
repairable in the field. Customer engineers are therefore directed to return all
chassis and laser subsystems to the factory or service depot when replacement of
the optical subsystem is required.
!
WARNING
Use of controls, or adjustment, or performance of procedures other than
those specified in this manual may result in hazardous radiation exposure.
!
WARNING
WARNING: Turn off the main switch before attempting any of the
procedures in the Laser Unit section. Laser beams can seriously damage
your eyes.
CAUTION MARKING:
2
OVERALL INFORMATION A292/A293
3,000 SHEET FINISHER B312
DETAILED DESCRIPTIONS A292/A293
BOOKLET FINISHER A763
INSTALLATION A292/A293
COPIER CONNECTION KIT B322
SERVICE TABLES A292/A293
PAPER TRAY B375
TAB
POSITION 1
TAB
POSITION 2
TAB
POSITION 3
TAB
POSITION 4
PREVENTIVE MAINTENANCE A292/A293
REPLACEMENT AND ADJUSTMENT A292/A293
TROUBLESHOOTING A292/A293
3,000 SHEET FINISHER B302
TAB
POSITION 5
TAB
POSITION 6
TAB
POSITION 7
TAB
POSITION 8
Loading...