Aervoe Industries 595 User Manual

No. 1595 - 01/13

Product Data Sheet

Aervoe Industries, Inc.

P.O. Box 485, Gardnerville, NV 89410

[phone] Phone • [phone] Fax • [phone] Customer Service

www.aervoe.com • [e-mail]

UNDERCOATING & SOUND INSULATOR

Aerosol

PRODUCT NUMBERS: 595

I. GENERAL DESCRIPTION

Description: Aervoe Undercoating & Sound Insulator is

a quick-drying, black, rubberized lm designed to offer
maximum coverage, durability and protection against
corrosion. It provides superior insulation properties

against road and chassis noise.

Benets: This multi-purpose coating provides a superior
protection against rust, road salt, dust, fumes and
moisture. It is designed to protect metal from corrosion
and abrasion. Effective after repairs and on replacement
parts. Remains exible and will not ake or chip off under
vibration. Deadens sound. Reduces downtime by several
seasons when applied to swamp coolers or tower coolers.
Provides superior performance to that of submarine cooler

coatings.

Application: Use on auto underbodies, trunks, fender
and body seams, rust holes, weld joints, gas tanks, fender
and panel replacements. Also useful for sealing rain
gutters, coating tree wounds, minor roof repairs, driveway
cracks, swamp and tower cooler coating, etc.

Directions: Align spray head with black mark on valve
rim to ensure complete evacuation. Before spraying,
shake can vigorously for at least 1 minute after agitator
ball is heard and intermittently thereafter. Surface must be
dry and free of dust, dirt, and heavy corrosion. For best
results product should be used at temperatures between
60° and 80° F (16° and 27° C). Hold can 10 to 12 inches
from surface to be coated, and press spray head rmly.
Material is delivered in a high pressure conical spray
pattern, use steady, even strokes while spraying, making
sure to keep spraying hand in motion. Two light coats
are better than one heavy coat. Immediately remove
any overspray with a cloth dampened in mineral spirits
or safety solvent. Spray in well ventilated area. After
spraying, turn can upside down and press button for
approximately two seconds to clear material from valve
and tip. If undercoating is to be top coated, use a good
quality exible enamel or lacquer. Test paint-cured panel
(24 hours) to ensure paint compatibility before use.

Limitations: Please refer to the Safety Data Sheet for
specic information on material hazards, etc. Note that

car trunks and interior areas require special attention
to remove vapors. On cars with catalytic converters,

avoid application of an undercoat or rust proong
material on or near converter, mufer, exhaust and
tail pipes due to extreme heat generated by system.

Not for sale in California.

Packaging:

Aerosol: Cans (211x604) 15 oz. net wt. (425 grams) 19.0 . oz. (562 ml)

12 cans/case 16 lbs. (7.3 kg) 0.55 CF (0.016 CM)

II. CHARACTERISTICS & PROPERTIES

Specications:

..............................................................................................................None

Appearance:

Gloss at 60° F ......................................................................................<5

Class .....................................................................................................Flat

Color:

..............................................................................................................Black

Coverage:

Theoretical-at 1 mil dry .........................................................................22 sq. ft./can

Practical-at 1/2 mil dry ..........................................................................44 sq. ft./can

Dry Schedule:

To touch ................................................................................................45 min.

To handle ..............................................................................................1 hr.

Full cure ...............................................................................................72 hrs.

To recoat ..............................................................................................Before 2 hrs. or after 72 hrs.

Performance and Chemical Properties:

Weight per gallon .................................................................................7.19 lbs

Specic gravity .....................................................................................0.8

Viscosity ...............................................................................................N/A

Flammability: Label marking ................................................................Extremely Flammable

Flash point ......................................................................<0° F (-18° C)

Application temperature .......................................................................50° F to 90° F (10° to 32° C)

Percent solids by weight ......................................................................29%

Percent solids by volume .....................................................................24%

Percent pigment by volume ..................................................................9%

Volatile Organic Compound Level ........................................................< 71%

CARB VOC ..........................................................................................< 40%

Dielectric strength ................................................................................N/A

Interior durability ...................................................................................Excellent

Exterior durability .................................................................................Very Good

Film temperature resistance .................................................................Good to 300° F (148° C)

Softening point .....................................................................................150° F (65° C)

Color fastness ......................................................................................Good

Adhesion (ASTM) D3359 ..................................................................... Very Good

Salt spray corrosion (ASTM B117) .......................................................Good

Mineral Spirits resistance .....................................................................Good

Gasoline resistance...............................................................................Good

Motor oil resistance ..............................................................................Good

Pencil hardness (ASTM D3363) ...........................................................2B

Base Materials:

Resin system ........................................................................................Synthetic Rubber, Alkyd

Solvents ...............................................................................................n-Butyl Acetate, Aliphatic Petroleum Distillates

Propellent: ............................................................................................Hydrocarbon

III. SHIPPING, STORAGE AND HEALTH

Aerosol

UN number ............................................................................. UN1950

Proper Shipping Description .................................................. Aerosols

Hazard Class .......................................................................... 2.1

Packing Group ....................................................................... N/A

Limited Quantity ..................................................................... Yes

Warehouse storage level number .......................................... NFPA 30B Level 1

Storage temperature .............................................................. 32° to 120°F (0° to 49°C)

Shelf life ................................................................................. 1 to 3 years

HMIS ratings

Health ...............................................................................2

Fire ...................................................................................4

Reactivity ..........................................................................1

IV. MISCELLANEOUS

Contains no Ozone Depleting Substances (O.D.S.)

V. WARRANTY

1-year performance warranty on all products from date of
purchase. Report to home ofce or local Aervoe representative
for examination. Because Seller cannot control Buyer’s handling
or use of product, Seller makes no warranty expressed or implied
when not used or stored in accordance with directions. Seller
shall not be liable for cost of labor, incidental or consequential
damages, and this warranty is limited to replacement of product

or credit of purchase.

NO.1595- 01/13