Aervoe 32-Watt Portable Light System User Manual

Aervoe® 32-Watt Portable Light System #8710

Aervoe’s 32-Watt Portable Light System is a rechargeable, high-powered light suitable for industry,
construction, home repair, or anywhere additional light is needed. Recharge using 12V DC or 120V AC
electricity to power the white or red LEDs. Also includes two USB ports to charge handheld devices.

IMPORTANT SAFEGUARDS

• Read all instructions before operating

• Do not look directly at the light; may cause injury to your eyes

• Do not use in flammable or explosive environments

• Do not charge in wet environments

• Do not operate at temperatures above 120°F or below 32°F

• To reduce the risk of electric shock, do not submerge the unit or its accessories in any liquid. Unit is
water resistant but not waterproof.

• Turn off all lights before charging

• Do Not store when the battery is completely drained; could cause damage to the battery

• Store in a clean dry place when not in use

• Only use the charger included with this product

• Administer close supervision when using around children

PARTS IDENTIFICATION

Green LED

Green LED

Green LED

Yellow LED

Red LED

100% charged

80% charged

60% charged

40% charged

Power Indicator LED/
20% charged

Handle

LED
Light Box

Screws to
Remove Light

Light Option
Switches

Battery Charge
Level LEDs

Power
Indicator LED

Fig. 1

Battery Box

USB Ports

(Under Dust Cover)

Power Switch

Charging Input

CHARGING THE RECHARGEABLE BATTERY

Before charging, turn off all lights.

Both chargers are stored in a compartment inside of the BATTERY BOX. To access, remove the LED LIGHT
BOX by unscrewing the two side SCREWS and open the storage compartment.

1. Turn the POWER SWITCH on before charging. The POWER INDICATOR LED will illuminate

2. Choose your desired charging option - 120V AC or 12V DC. Connect the XLR twist plug to the 3-PIN
CHARGING INPUT and plug the other end into either an electrical wall socket or vehicle power outlet.
Other portable 12V battery storage units may also be used (see Sierra Wave product line for available
options).

3. The LED light on either charger will change from Red to Green when charging is complete.

4. When charging from a vehicle, the engine must remain running to avoid draining the battery or
causing damage to the vehicle’s electrical system.

5. When the 5 CHARGING INDICATOR LIGHTS are illuminated, charging is complete. Remove the
charger once fully charged (see fig. 1).

6. To avoid overcharging, a protective circuit will automatically interrupt power to the battery if external
voltage is too high or the battery is fully charged.

Low Battery Indication:
If battery level drops to 10% the power will shut off all functions except for the power indicator light.
Recharge as soon as possible and turn off the POWER SWITCH to conserve energy.

• Using Lights on 2 Sides: when battery power drops to less than 1 hour of use, a warning beep will
sound for 20 seconds every 15 minutes.

• Using Lights on 1 Side: when battery power drops to less than 1½ hours, a warning beep will sound
for 20 seconds every 15 minutes.

• Recharging will be needed. To avoid damage to the battery recharge a fully discharged battery within
24 hours and a stored battery every 3 months.

OPERATION

• For convenience the light can be operated with the LED LIGHT BOX attached to the BATTERY BOX or
using the 16’ extension cord it can be placed on any stable surface away from the battery. It can also
be hung using the 2 holes in the handle. To remove it from the BATTERY BOX, remove the 2 side
SCREWS on the side and pull off.

• Swivel the cross-bar 90º on the bottom of the LIGHT BOX to provide a stable base. Use a sandbag or
other heavy object to provide an anchor if it is being used in high wind.

• Power off when not in use.

• Use the included Rain/Snow cover to protect the battery and internal components when used
outdoors. Unzip and place over the battery box, wrapping around the extension cord.

Light Operation:

Front Red

LED Switch

Front White
LED Switch

Switch #1: controls the red light in front
Switch #2: controls the white light in front
Switch #3: controls the red light in back
Switch #4: controls the white light in back

USB Ports

USB 1.5A PORTS

Back Red

LED Switch

Back White
LED Switch

1. Lift the rubber protective cover to expose the 2 USB ports. These are available to charge any device
with a USB power cord.

2. Turn on the Power Switch before using the USB ports.

3. Replace the cover when not in use to keep dust out.

TECHNICAL INFORMATION

SPECIFICATIONS

INTERNAL RECHARGEABLE BATTERY AGM Sealed Lead Acid 12V/12Ah

575 charge cycles
F2 Terminals

5.875” x 3.875” x 3.75”

DC VOLTAGE 12/24V

AC VOLTAGE 100-240V

LEDs 60 White

48 Red

LUMENS 1050 each side (2100 total)

EXTENSION CORD LENGTH 16 ft. (5m)

CHARGING METHOD 120V AC Power Adapter 5 ft. (1.5m)

Input: 120V AC, 50-60Hz
Output: 12V DC, 1Ah

12V DC Power Adapter 6½ ft. (2m)

Input: 12-24V DC
Output: 12V DC, 1Ah

ACCESSORIES Adjustable shoulder strap

Rain/dust cover

OPERATING TEMPERATURE 32ºF - 120ºF (0ºC - 49ºC)

When operated below 60º (15ºC) battery level will drop to
60%

WEIGHT 18.5 lbs. (8.4kg)

DIMENSIONS 10.5” x 6.75” x 25.5” (267 x 171 x 648mm)

RATING IP44

POWER DURATION

Battery recharges in 12-13 hours

White LEDs: Single side 10 hours

White LEDs: Both sides 5 hours

Red LEDs: Single side 10 hours

Red LEDs: Both sides 5 hours

Based on a fully charged battery.

32-Watt Portable

Light System

OPERATING INSTRUCTIONS

8710inst; cs12/13

AERVOE INDUSTRIES, INC.

Gardnerville, NV 89410 • 1-800-227-0196

www.aervoe.com • [e-mail]