Aervoe 30-Watt Solar Collector User Manual

Sierra Wave™ 30-Watt Solar Collector #9530

Adjustable Kick Stand Supports

Angle Adjustment

Notches

Metal

Supports

Magnetic Closure

DC Out

Cable

Solar
Cells

LED Charging

Indicator

Magnetic Closure

ON/OFF

Switch

Power Center Adapter Cable

12V DC Female Socket

Battery Clamps

Load

12V Battery

Solar Panel

Charge

Controller

Low

Voltage

Charging

High

Voltage

LoadSolarBattery

IMPORTANT SAFEGUARDS

Read all instructions before operating and keep for reference. Only use as directed.•
To reduce the risk of electric shock, do not submerge the unit or its accessories in any •
liquid
Do not operate in wet environments•
Protect solar panels from scratching. Do not place other objects on top of panels to •
avoid damage.
Do not use abrasive cleaning products to clean solar panels•
Store in a clean dry place when not in use•
When using the 7A Charge Controller, follow instructions carefully to avoid personal •
injury and explosion or other damage to batteries, the solar panel, or Charge Controller
Not intended for use by children. Administer close supervision when children are nearby•

PARTS IDENTIFICATION

SOlAR COllECTION & ChARGING

This 30-Watt Solar Collector includes accessories to allow a direct solar charge to a variety of
rechargeable devices including tools, worklights, laptops, and other more sophisticated battery
centers such as the Max Burton® Power Center

100 #6994 and Sierra Wave™ Power Cell #7630.

In many cases you will need your specific device’s 12V DC charging adapter (vehicle charger).
Using the included 7A Charge Controller allows you to trickle charge vehicle batteries for cars,
trucks, RVs, boats, and motorcycles. The optional Chainable Cable #9501 connects up to three
30-Watt Solar Collectors to create 90 watts of power (sold separately).

Solar Collector Set-Up:

Unfold the solar collector by opening the hard case.1.
Release the 2. ADJUSTABLE KICK STAND supports from the back and adjust the angle of
the support so that the SOLAR PANELS are facing the sun with maximum exposure.
Adjustment will be required throughout the day as the sun travels across the sky.
Move the 3. ON/OFF SWITCH to the ON position. A blue LED POWER INDICATOR will flash
to indicate when the solar panels are detecting solar energy. NOTE: it does not indicate
sunlight intensity.
Unwind the 4. DC OUT CABLE on the collector to the desired length to reach your charging
device.
Choose an accessory cable or adapter to match the specific device you wish to charge (see 5.
below).
Insure all connectors are secured tightly.6.

Charging a Max Burton® Power Center100 #6994 (sold separately):

Read all instructions included with the Power Center.1.
Connect the included 2. POWER CENTER ADAPTER CABLE to the DC OUT CABLE on the Solar
Collector.
Connect the other end to the DC IN #1 port located on the Power Center.3.
Charging will start when the blue LED on the Solar Collector blinks.4.
The battery meter on the Power Center will flash to indicate it is receiving a charge.5.
Stored power in the Power Center may be used at the same time it is collecting solar energy 6.
or can be stored for use later when not connected to the Solar Collector.

7A Charge Controller:

Using the included 7A Charge Controller is necessary when charging 12V batteries to protect
them from over charging, over discharging, and it provides load output control to your device.

Connect the included 1. BATTERY CLAMPS to the cable on the Charge Controller labeled as
BATTERY.
Connect the 2. BATTERY CLAMPS to the 12V battery with the (-) negative black clamp to
the battery post marked (-). Then connect the (+) positive red clamp to the battery post
marked (+). WARNING: connecting the clamps to the battery incorrectly can cause

fire, explosion and battery damage.

Connect the cable on the Charge Controller labeled as SOLAR to the 3. DC OUT CABLE on
the Solar Collector.
The Charge Controller and cables should be placed off of the ground to avoid damage 4.
from walk-by traffic. Make sure all cables are securely connected.
If a device (load) is being operated, connect the included 5. 12V FEMALE SOCKET to
the cable on the Charge Controller labeled as LOAD. NOTE: Verify that your device
is compatible with the Charge Controller’s specifications before connecting to avoid
damage.
Connect the other end to your device’s 12V DC charging adapter and then to your device.6.

Charge Controller LED Indicators

High Voltage Protection: If the 12V battery reaches a pre-determined high voltage level,
the green High Voltage LED Indicator will illuminate. Solar charging to the battery will
automatically stop until the battery reaches a safe voltage.

Charging In Process: When the Solar Collector is connected, the yellow Charging LED
Indicator will illuminate as long as adequate solar energy is provided.

Low Voltage Protection: If the 12V battery reaches a pre-determined low voltage level
the red Low Voltage LED Indicator will illuminate. Operation of the load will automatically
stop until the battery reaches a safe voltage.

Charging the Sierra Wave™ Power Cell #7630 or other small electronic devices (sold

separately):

Read all instructions included with the device you wish to charge.1.
Connect the included 2. 12V DC FEMALE SOCKET to the DC OUT CABLE on the Solar
Collector.
Connect the other end to your device’s 12V DC charging adapter. 3. Caution: This Solar

Collector has a high DC output range of 15-20 volts. Using your device’s specific 12V DC
charging adapter will prevent overcharging and battery damage.

Disconnect the Solar Collector when fully charged or not in use.4.
NOTE: The 7A Charge Controller is not required if the device has built-in charge protection.
Check all devices before connecting for compatibility. If charge protection is not built-in, the
Charge Controller will be required to keep from damaging your device.

Connecting Multiple Solar Collectors with the Chainable Cable #9501 (sold separately):

#6994 Power Center

#9501 Chainable

Cable

DC Out Cables

Allows up to three 30-Watt Solar Collectors to be connected to provide 90 watts of power.

Connect the 1. DC OUTPUT CABLE of each Solar Collector to the end of the CHAINABLE
CABLE (the end with the 3 cables).
Connect the other end to any storage device such as the Power Center2. 100, Power Cell, or
other device.

TEChNICAl INFORMATION

SPECIFICATIONS

SOLAR COLLECTOR 30-watt monocrystalline CE, FCC approved

POWER OUTPUT 15-18V DC (working - based on available sunlight)

19-20V DC (no load)

OPERATING TEMPERATURE 32º - 120ºF

WEIGHT 10.5 lbs.

DIMENSIONS 30.25” x 20.5” (open)

20.5” x 15.5” (closed)

ACCESSORIES 1 - battery clamps

1 - 12V DC female socket
1 - Power Center adapter cable
1 - 7A Charge Controller

30-Watt Solar
Collector

7A CHARGE CONTROLLER Maximum input: 20V DC ~ 7A/100 watts

Operating Temperature: 32º-120ºF
Over Charge Protection: 14V DC (+0.5V)
Over Discharge Protection: 11.0V DC (+/-0.3V)
DC Output (load): 5A max

ChARGING DATA

#6994 Power Center 6-8 hours for a full charge

#9620 20-Watt Power Hub 8-10 hours

#9630 50-Watt Power Cell 6-8 hours

12V vehicle, RV, boat or motorcycle battery Time will vary depending on the battery type,

Smartphones & Standard Cell Phones
(using device’s 12V vehicle adapter)

eReader/Tablet Computer (using device’s
12V vehicle adapter)

Actual results will vary depending on available

sunlight and the device being charged

2-4 hours when 3 are chained together

voltage level and capacity. Reference your

battery manufacturer’s specifications.

2-6 hours depending on model

6-8 hours depending on model

OPERATING INSTRUCTIONS

AERVOE INDUSTRIES, INC.

Gardnerville, NV 89410 • 1-800-227-0196

www.aervoe.com • [e-mail]

9530inst; cs2/12