Page 1
Tel: +86 755
6182 9288
Fax: +86 755
6182 9288
Email: overseas@aerovtech
.com
AeroV
P16 O
utdoor
User’s Manual
Please read the following safety protection to make sure correct and safe
operation during installation, power on, operation and maintaining.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Shenzhen, P.R.China
Post code: 518111
Website: www.
aerovtech
Technology Ltd.
Full Color LED Display
WARNING!
Industrial Zone,
.
.com
Page 2
Tel: +86 755
6182 9288
Fax: +86 755
6182 9288
Email: overseas@aerovtech
.com
☆
Safety Information
☆
This equipment is permanently connected equipment, a readily accessible disconnect
device shall be i
ncorporated in the building installation wiring
☆T
he rated current of overcorrect protective device used in installation should be 20A or less.
☆
For supply connections, use wires suitable for at least 80°C.
Utiliser des fils convenant à une température d
☆
The following signal indicates the safety information on the product and operation manual.
Too much hot and electrical attack will cause serious damage
Dangerous!
Very dangerous, direct touch
will cause serious damage or
death.
Warning!
Fire dangerous.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Shenzhen, P.R.China
Post code: 518111
Website: www.
aerovtech
Warning!
Read the manual before installation,
power-on and maintenance.
Warning!
Intensity light will damage eyesight.
Industrial Zone,
.
.com
Warning!
High voltage dangerous!
Page 3
Tel: +86 755
6182 9288
Fax: +86 755
6182 9288
Email: overseas@aerovtech
.com
Please read and follow up user manual and warnings carefully before installation
and operation. If you have any questions about how to operate the P
Screen safely please contact
Darklight
In order to avoid electrical shock please note:
Power off before disconnection and installation the P
Screen.
ONLY apply to
Power off during connection, installation, disconnection and maintaining.
DO NOT operate this product under humid and rainy condition weathers
DO NOT apply the products where there are flammable, erosive materials
DO NOT apply the products near heat
temperature may cause damage to the lighting fixture
Please
make sure that all connections are secure and tight
DO NOT uncover the product without permission and guide
No recycling components inside.
The product shall only be installed and dissected by professionals
Product details are subject to change without n
DO NOT view the product below 40cm without eye
DO NOT view the fixture directly from the focus light instrument
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Shenzhen, P.R.China
Post code: 518111
Website: www.
aerovtech
16
Outdoor Full
directly or its dealer
16
Outdoor Full
local current
-
emitting source, or the rising
otice.
-shield.
Industrial Zone,
.
.com
-color LED
-color LED
.
Page 4
Tel: +86 755
6182 9288
Fax: +86 755
6182 9288
Email: overseas@aerovtech
.com
Chapter 1.
Specification and Per
1.1
Specification…………………………………….…
1.2
Performance……………………………………….
1.3
Function description………………………..……..
1.4
LED Screen model definition.
Chapter 2.
Structure and Installation……………………………....
2.1
Cabinet structure……………………………………
2.2
Module structure………………………………….…
2.3
Cabinet assemble…
2.4
Screen install
2.5
Screen framework structure…….……………
Chapter 3.
Screen System Installation………………………
3.1 P
C operation system installation………………..…
3.2 C
ontrol card
3.3
Cable connection step……...
3.4
Software installation...................
Chapter 4.
Display card
4.1 ATI
display card
4.2
GEFORCE
4.3 Comp
uter Troubleshooting
Chapter 5.
Troubleshoot
5.1
System checking
5.2
common tr
Chapter 6. S
ignal PIN definition and CAT
6.1
Module PIN definition…….
6.2 Signal
cable
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Shenzhen, P.R.China
Post code: 518111
Website: www.
aerovtech
Contents
type…………………………………
installation
…………………………
………………..
.…….
…………....
….….
configuration…
………………………
configuration.……..……...
...…...….
display card configuration.…...
…...….....
configuration…
……..…..
ings..…………………………...
……......…
……….………………...
……..…
oubles ………………………………
…..….
6 facture ………
…
facture……………………………………...
Industrial Zone,
.
.com
5
5
6
6
7
8
8
8
...9
.9
……10
….…13
13
.…13
14
….….
16
...…18
18
21
23
25
….26
27
..…...28
.…....28
29
Page 5
Tel: +86 755
6182 9288
Fax: +86 755
6182 9288
Email: overseas@aerovtech
.com
Chapter 1.
Specification and Performance
P16
Outdoor full color LED Screen is a kind of advanced screen which functions with
scanning;
it is very popular among users. Pictures shown by this screen is with perfect
performance. It is suitable for advertisement at bank, shop center, school, restaurant and similar
indoor and o
utdoor recreational applications.
DL-LSOFR16-SL
1.1 Specification:
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Shenzhen, P.R.China
Post code: 518111
Website: www.
aerovtech
Module Dimension: 256mm×256mm
Pitch: 16mm
Pixel configuration : 1R1G1B 3pcs Φ3
ellipse LED Unit
Module Resolution(L*W): 16*16
Pixel Density(pixel/ m2）: 3906
Brightness（cd/ m2）: ≥6000
Optimal Viewing Distance(m）: 16-48
Peak Power Consumption（≤）: 540w/m
2
Average Power Consumption（≤）: 20
0 W/m
Max Cabinet Current input: 3A
Cabinet Weight:: 41kg/m2
Scan Mode: Static Scanning
IP Rating: Front side IP65
Horizontal Viewing Angle: 120°
Vertical Viewing Angle: 60°
Drive Voltage(DC): 4.5～5.5V
Gradations: 256 Gradations for Red, Green and Blue
Frame Rate: 60（f/s）
Control Mode: Real Time PC Monitoring
Screen Lifespan: ≥100,000 hours
Operating Voltage: AC220V ±15％ 60
HZ
Effective Control Distance(m): up to 15
0 meters by CAT
cable, single fiber up to 20 kilometer.
Working Temperature: -20℃～50℃
Working Humidity: 10％～90％
Industrial Zone,
.
.com
static
2
6
Page 6
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
1.2 Performance:
Super brightness and even luminance, this screen is designed with 16 gradations for adjustable lighting
effect,
which can be achieved both manually and by self
different conditions;
Abundant and uniform colorful vision effects
Large viewing angle up to 120°horizontally and 60° vertically, no significant color
viewing angle
By applying PC multimedia technology
LED Screen, such as TV Signal, Video Signal, Video Tape recorder Signal, DVD Video Signal, PC Movie and
Letter Signal, etc. ;
Quality advantage: Stri
ct rules have been set from materials to finished products which have already been
under guarantee of reliability
Service advantage: Comprehensive service under same condition
1.3 Function Description:
Support DVI display : connect to
DVI port directly
Single CAT6 cable transmission:
1pc standard SUPER CA
Support far distance transmission:
communication chips, high anti-
resistance ability, simple and supporting no
150m
for communication distance CAT
kilometers, 100% data recover is achievable.
Stable and reliable:
adopt 4 layers PCB and single pc GSI design whi
remarkably.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
-
motion mode to ensure different viewing effect under
，
it is very convenient to display various types information source by
.
T6
cable transmission
n-rel
ay far distance transmission
6 Cable can be achieved, multi-
module fiber
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
loss from the standard
.
-mega data
.
300m, single-module fiber 10
Page 7
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
1.4 LED Screen model definition
[1] [2] [3]
[4] [5]
For example:
AV-LSOFR16-C：P16
real pixel, outdoor
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
[6] [7]
full color led screen with Cree LEDs.
7. LED chip:
E --Economical
，
S – Silan，
two years
C – Cree，
three years warranty
5. Pixel constitutes:
Full color screen
S (SMD) --SMD
3in1;
F(3 SMD)--
SMD 3for1;
V (Virtual Pixel)
-
R (Real Pixel)--
Real Pixel
Dual color screen:
A--1R1G;B--
2R1PG;C
Single color screen
X--1R;Y--1G;Z--
2R;
6. Pixel pitch(mm):
Use number
express
For example: P10
、
Especially: V—
Variable;
4. Display color:
S --
Single Color ;
D -- Dual Color ;
F -- Full Color ;
3. Use environment:
O-- outdoor ;
I -- Indoor ;
1. Company name:
AV—
AeroV Technology Limited
2. Product type:
LS -- Led Screen
;
LT -- Lighting ;
PX-- Pixel ;
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
one year warranty;
warrant;
;
-Virtual pixel ;
;
--1R1YG;D--2R1YG;
,unit(mm);
P16、P20;
Page 8
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
Chapter 2.
2.1 Cabinet structure
P16
Screen adopts case structure design
follows:
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Structure and Installation
，cabinet dimension is 1024mmX
768
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
mmX175mm, pictures as
Page 9
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
2.2 Module structure
Module is the smallest unit of Outdoor full color LED Screen; Cabinet is made up of modules. P
module dimension is 256*256mm
; resolution is
2.3 Cabinet assemble
Modules
assemble to cabinet as follows:
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
16*16 pixels, pictures as follows:
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
16 display
Page 10
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
2.4 Screen installs type
It’s very important to Setup a horizontal, stable, firm platform for LED Screen, common install type as follows:
Outdoor LED Screen could adopt A/B/C/D/E/F; Indoor LED Screen c
2.5 Screen framework structure
The design of the outside framework structure is decided by the installation requirements of LED Screen;
screen size and color of surround stance. With the condition of guarantee adequate installat
minimize the weight of the framework.
For indoor LED Screen, normally there are two kinds of material of outside framework: Black aluminum alloy
covered with stainless still(Dull and bright).black aluminum framework is simple i
close to the background color of LED Screen; then aluminum alloy covered with stainless steel framework is
very beautiful and elegant.
For Outdoor LED Screen, in order to make sure having enough intensity and strict wat
framework should be steel structure. According to onsite circumstance and user’s requirement, normally
aluminum panel with plastic coat be used for the decoration. Screen installation step as follows:
1. Check whether the structure
of LED Screen is made in reason or not
the bottom layer structure should be solid.
the width and height of the structure is suitable or not, usually larger than LED Screen 5~10mm is proper
the distance between two
pillars from the bottom to the top should be strictly the same. Otherwise, it will cause
gap when install the cabinet.
check the passage position inside the maintenance box is suitable or not and if it will block the cabinet door, if
not sui
table the cabinet door could not be opened after LED Screen finished installation.
the holes for cables going through at two sides of cabinets will not be blocked.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
:
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
ion intension, try to
n structure, and the color is
er proof effect, outside
Page 11
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
2. According to the number of cabinets, please install the cabinets from th
between cabinet methods is showed as below.
Make sure that the bottom layer of cabinets should be very flat, and then install the upper layer cabinets. Put water
proof glue onto the joint bet
ween two cabinets. After the whole LED Screen finish debugging, the LED Screen
framework should do strict water proof treatment.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 12
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
3. Connect well the
electricity power cable and CAT
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
6
cable according the cable connection diagram.
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 13
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
Chapter 3
Screen System Installation
LED Screen can work normally after finishing system installation according to the following steps:
3.1 PC operation system installation
Windows 2000 ,Windows XP or Windows vista operation s
is recommended.
PC configuration:
CPU: CoreDou 2.4GHZ or above
Memory
: DDR II 800HZ 2G or above
Main
board: at lease with 2 PCI slot for sending card installation. 1 COM port, 1 PEC
Hard disk: SATA II
160G or above;
Monitor: 17’
for 1024*768 resolution, 24
Graphic card: with VGA and DVI output,
Keyboard and mouse: normal
3.2. Sending card i
nstallation
1）Installation display card
We recommend to use the display card which contained with both VGA and DVI output port or double DVI
output port, such as GeForce
95
2）
Installation LED Screen sending card
First, Insert sending card
into computer main
card and sending card with DVI cable, and then connect PC
transfer cable.
3) Hardware Connection
Connect the power supply of screen,
card.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
’ for 2048*1536 resolution;
00（recommend to use）.
board PCI slot; then connect the DVI port between display
USB
port and sending card
signal wire between cabinets, signal wire between PC and receive
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
P operation system
-E slot;
COM port with serial
Page 14
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
4) System Configuration List:
Sending card: 1pc
Receiving card: Confirm the amount according to the screen
Serial transfer cable: 1pc
DVI cable: 1pc
SUPER CAT6 IBDN Cable: 1pc
3.3 Cable connection step:
1. Preparation:
Uncover PC ho
st, change common display card by DVI
Install sending card and connection all cables(DVI and
Covers the PC host and startup computer.
Install DVI display card driver
(NVIDIA or ATI) step by step.
Setup display card advance setting (refer to next chapter)
Install LED Screen program. (LED Studio), install serial number is 888888.
Connect the LED Screen sending card with the input port of first receiving card in the cabinet.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
and VGA
double output display card
USB cable)
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 15
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
2 .Outside wire connect as following:
Power cable connection as following:
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 16
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
3. Module cable connection as following:
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 17
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
3.4 Software installation:
Step 1. Put Software CD Disk into CD
manual with double click install icon, then select “English” and click “OK”;
Step 2. Click “Next” step by step;
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
-ROM driver, the program should ru
n automatically, if not, please run in by
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 18
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
Step 3. When the following picture is appeared, please type in pas
Step 4. Click “Next” button until finished the installation;
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 19
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
Step 5. Click “Finish” button;
Step 6. After installation, the following picture is showing ;
After “LED Studio
8” software has been successfully installe
the 【Start】/【Program】/【
LED Soft
to start program. Als
o, there will be a “LED Studio
start the program
by double click on the icon.
Detail operation of the
LED studio software;
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
】, then move to the “LED Studio
8” under this program group, click the icon
8” short-cup on your
desktop, as
please refer to “LED Studio user’s manual”
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
8” program group in
shown below. Also, you can
Page 20
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
Chapter 4
Usually we have two different type display card, they are used
following chapter 4.1 and chapter 4.2.
4.1 ATI Display Card
configuration
1.
Press right bottom of MOUSE on the blank of desktop, enter into shortcut menu and choose Properties,
setting the screen resolution
to 1024 x 768 pixels as follows:
2. Press “Advanced” to setting the
refresh rate
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
NVIDI
A or ATI display control IC, detail setup as
of the monitor to 60HZ as follows:
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 21
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
3．Press “display” option，
turn FPD to green color as follows:
4. Press “Recover” option, enter
into “clone mode options”, and the choose “Same on all” as follows:
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 22
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
4.2 GEFORCE Display card
configuration
1.
Press right bottom of MOUSE on the blank of
the screen
resolution to 1024 x 768 pixels as follows:
2. Press “Advanced” to setting the refresh rate of the monitor to 60HZ as follows:
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
desktop
, enter into shortcut menu and choose Properties, setting
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 23
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
3. Press “GeForce 9500GT” options.
Click
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
“Start the NVIDIA Control Panel”, and
then click
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
“OK”.
Page 24
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
4. When “NVIDIA Control Panel”
is showing, select
5. Choose “Clone”
display mode, and then select
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
“Set up multiple displays”.
“
Samsung syncmaster + LED 1024x768
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
”.
Page 25
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
6. Click “Apply” ,and then click “Yes”.
4.3 Computer
Troubleshooting
1. Press right bottom of mouse on the blank of table
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
configuration
-
board, enter into shortcut menu and choose Properties:
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 26
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
2.
Press "Advanced" to get “Troubleshoot” menu as following:
3. Pull the “Hardware acceleration” from “Full” to “None”, a
Choose “Apply” and “OK
". Quit from Properties Selection.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
s following:
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
Page 27
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
Chapter 5
5.1. System checking
Please check system according to the following steps if the LED Screen can not work normally afte
the connection and
the power supply:
1).
Check the power supply system of the screen
2).
Check the settings of LED control software
3)
Check power supply, display module, scanning board, power supply indicator light.
of the relative circuit board is DC5
4). The Green L
ight on the receiving board will winkle under normal condition.
5).
The Red Light and the green Light on the main card will last
condition. If the Red Light does not work, c
display card properties settings or check the DVI wire.
6).
Check LED Screen module circuit according to the following steps:
Step 1.
Check if the connect wires between display module are
Step 2.
Check scanning board polarity and module connection.
Step 3.
Check the indication light of sending card.
Step 4.
Check the indicating light of the receiving card.
Step 5.
Check the connect system refer to the a
Step 6.
Check the connection of DVI wire.
Step 7.
Check the display card settings; please refer to the display card setting part.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Troubleshooting
V±0.3 by multi-meter.
-
shining and twinkle respectively under normal
ccessory connect mode.
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
r finishing
Measure connector plug
Page 28
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
5.2 Common Troubles
Trouble
Description
Trouble Analysis
The whole
screen do
not work
The power supply does not work
LED Control software setting power off
Signal cable does not connect well
The LED Screen
shows black color
Module power supply does not connect well
or voltage does not match
The connect wire between module and
scanning board is too long
Screen
twinkle
Signal
cable longer than
some problem
with cable wire
Signal cable
does not fasten stably.
Control
software
are out of
control
RS232 cable is unplug
g
Some trouble with LED unit module
Display card s
etting incorrect.
LED Control software is locked
Power supply will not increase when
increasing power supply to the module
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
Solution
change power supply
Setting control software to power on
Reconnect signal
cable
Reset the computer d
esktop back color
Make sure the voltage above
R
educe the length of the signal cable
the stated length or
Make sure the cable wire quality
length
is no more than 130 meters
Re-insert the cable
ed or plugged lax Re-
plug the RS232 cable
Check the module
Reinstall the Display card
Open the control software
Increase power supply of
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
DC4.75Ｖ
is ok and the
receiving board
Page 29
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
R1B B1 R2B B2 GND
-----
R1A G1 R2A G2 CL
ST
1
2
Chapter 6.
Signal PIN definition and CAT
6.1 Module PIN definition:
For the convenient to maintain LED Screen, we offered module signal pin definition as following:
★ Single pin definition:
GND= Ground
ST = Latch signal
CL = Clock signal
OE = Enable signal
R1A, R1B = First Red data
G1 = First Green data
B1 =First Blue data
R2A, R2B = Second Red data
G2 = Second Green data
B2 =Second Blue data
6.2 Signal wire facture:
Communication wire（
connect transfer card
following standards facture.
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
GND
OE GND
15
16
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
6 facture
）according to the
Page 30
Tel: +86 755 6182 9288
Fax: +86 755 6182 9288
Email: info@aerovtech.com
1. Take off 3cm at the front end outer skin of the double
tools)
2. Match wire correctly
Please
make sure that: wire1 and wire 2 form a circle match
form a circle match；
Wire7 and wire8 form a circle match. At both ends of the wire, same methods will be used. The
wire match is arranged in serration a
fter certain color sequence.
4、green, 5、white blue, 6、blue, 7、
white brown, 8
After matching the wires, trim the wires; cut off the bare part of the double
ou
tsides. Wire heads shall be trimmed to uniformity, then put each wire of the double
connector lead, the first lead shall be connected with orange
After all the double-twist wires
have been placed tightly, then press wire and let the wire to meet with the RJ45
connectors with RJ45 wire-
meet clamp
On the other end, the connection method is the same; after all above action completed, the RJ45 connectors shall
be in uniformity\. At,
test the connection with measuring equipment, then the RJ45 connector is OK.
Signal wire（
connect sending card and receiving card
One side: 1. white orange, 2. orange, 3.white green, 4. blue, 5. white blue, 6.g
brown
Another side: 1. white orange, 2. orange, 3.white green, 4
brown
If all above measures have
please contact us through E
AeroV Technology Limited
Add:
Building 44, Fumin
Pinghu Street
Post code:
Website: Http://www.
-
twist cable with special double
；
wire3 and wire4 form a circle match
（Such as: 1、
white orange, 2
、brown）.
-
twist cable, with only 15mm length left
-
whitish wire, and the following in the same sequence.
）
should be made as following steps:
-mail、FA
X or phone call to get after
Industrial Zone,
Shenzhen, P.R.China.
518111
aerovtech.com
-twist cable peeler (or other
；wire5 and wire6
、orange, 3、white green,
-twist wire into to RJ45
reen, 7.white brown, 8、
6.green, 7.white brown, 8、
n not be solved,
-sale service.
Loading...