Aero Pure ABF110DHG5, ABF110DHG6, ABF110DHL5, ABF110DHL6 Installation Manual

Model No.

BATH FAN

INSTALLATION INSTRUCTIONS

ABF110DHG5 Series

ABF110DHL5 SeriesABF110DHG6 Series ABF110DHL6 Series

READ AND SAVE THESE INSTRUCTIONS

Thank you very much for purchasing our bath fan.
Please read the instructions carefully before attempting to install,
operate or service our ventilating fan. Failure to comply
with instructions could result in personal injury or property
damage. Please retain this booklet for future reference.

TABLE OF CONTENTS

UNPACKING
SUPPLIED ACCESSORIES
DESCRIPTION
GENERAL SAFETY INFORMATION
DIMENSIONS
WIRING DIAGRAM
FEATURES
INDICATION (PLUG-IN DEVICES)

INSTALLATION
INSTALLATION

MAINTENANCE (CLEANING)
PRACTICAL GUIDE TO INSTALLATION
SPECIFICATIONS
WARRANTY

..............................................................................................................

.......................................................................................

..........................................................................................................

........................................................................

............................................................................................................

...................................................................................................

..................................................................................................................

...........................................

I (NEW CONSTRUCTION）
II (RETROFIT)

......................................................................................................

...............................................................................................................

.................................................................................

...................................................................................

.............................................................

...................................................................

02
02
02
03
04
05
05
06
07
11
13
14
14
15

UNPACKING

Unpack and carefully remove the unit from carton.
Refer to the supplied accessories list to verify that all parts are present.

SUPPLIED ACCESSORIES

Grille

Suspension
bracket
assembly

Long screw
(ST4X30)

Wire
Protector
Nut

Installation
instructions

or oror

ABF110DHG5 ABF110DHG6 ABF110DHL5 ABF110DHL6

1

1

5

1

1

DESCRIPTION

These bath fan models are listed by ETL under ETL file No.5011292.
These bath fan models use a Sirocco fan driven by a brushless DC motor.
The motor is designed to have an extended service life with reduced energy consumption.
The grille covering the fan body is a spring-loaded, quick attach type. A damper for preventing air
counterflow is provided.
The suspension bracket assembly can be used for both new and retrofit situation.
The light uses a bright SMD LED.

2

GENERAL SAFETY INFORMATION

Do not install this ventilating fan where interior room temperature may exceed

1.
104°F (40°C).

Make sure that the electric service supply voltage is AC 120V, 60Hz.

2.

Follow all local electrical and safety codes, as well as the National Electrical

3.
Code (NEC), and the Occupation Safety and Health Act (OSHA).

Always disconnect the power source before working on or near the fan, motor,

4.

light fixture, or junction box.

Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals

5.
or other objects.

Do not kink the power cord.

6

Do not install the unit where ducts are configured as shown in Fig.A.

7.

Provide make up air for proper ventilation.

8.

CAUTION:

1.For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.

2.Not for use in cooking area. (Fig.B)

3.This product must be properly grounded.

WARNING:

To reduce the risk of fire, electric shock, or injury to persons, observe the following:

1.

Use this unit only in the manner intended by the manufacturer. If you have any questions, contact
the manufacturer.

2.

Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.

3.

Installation work and electrical wiring must be done by qualified person(s) in accordance with
all applicable codes and standards, including fire-rated construction.

4.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacture′s

guideline and safety standards such as those published by the National Fire Protection Associa­tion (NFPA), and the American Society of Heating, Refrigeration, and air conditioning Engineers
(ASHRAE) and the local code authorities.

5.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden
utilities.

6.

Ducted fans must always be vented to the outdoors.

7.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the
application and be connected to a GFCI (Ground Fault Circuit Interrupter)-protected branch circuit.

8.

These models are ETL listed for tub and shower enclosures.

9.

Not to be installed in a ceiling thermally insulated to a value greater than R40. (This is required for
installation in Canada only).

3

DIMENSIONS

Model: ABF110DHG6 Series, ABF110DHL6 Series

③

②

⑩

10 1/4 (260)

12 1/8 (308)

⑦

①

⑧

Model: ABF110DHG5 Series, ABF110DHL5 Series

③

②

⑦

5 4/5 (147)

4 7/8 (123)

3 7/8 (98)

5 4/5 (147)

4 7/8 (123)

3 7/8 (98)

⑤

3 4/5 (97)10 2/5 (265)

④

7 1/3 (186)

Unit: inches (mm)

⑥

⑨

13 (330)

3/5 (14.5)

⑨

⑩

7 1/3 (186)

3 4/5 (97)

⑪

①

10 1/4 (260)

12 1/8 (308)

④

13 (330)

⑧

⑥

Blade

1

Grille

2

Adaptor

3

Damper

3/5 (14.5)

4

Frame assy

5

Knockout plate

6

Junction box

7

10 2/5 (265)

⑤

Base PCB box

8

Humidity sensor module

9

CO sensor module

10

2

Night light module

11

Motion sensor module

12

LED light

13

⑫

4

WIRING DIAGRAM

Model: ABF110DHG5 / ABF110DHG6

Fan body

Motor

Yellow­green

Junction box

P
C
B

White

Red

Red

Black

Green

Neutral

Control switch

Signal

Signal

Live

Ground

FEATURES

Multi-Speed

Flow-Selection

Air Volume(CFM)

50

80 110

80

70

90

60

50

0

Time delay

Air trimming

●CFM-Selection. Choose 50-80-110CFM; default is high speed.

Air Trimming

Time(min)

H

30

20

L

10

45

100

5

60

0

●Multi-Speed- Switch allows fan to run at continuous lower speed to

meet Indoor Air Quality. For example, when Flow-Selection setting is
80CFM, Multi-Speed can be chosen 0, 50, 60, or 70CFM as a
low speed.

Power switch

Model: ABF110DHL5 / ABF110DHL6

Fan body Junction box

Neutral

White

Motor

Yellow­green

Light Body

P
C
B

Brown

White

Blue

Red

Red

Black

Green

Signal

Signal

Live

Ground

Live (Light)

Neutral

Live(N. Light)

Control switch

Power switch

●Delay- Switch for time delay setting. Setting range is 0, 5, 10, 20,

30, 45, or 60 minutes.

●Air Trimming- Switch allows fine-tuning of air volume when the

actual airflow is lower than set.

INSTRUCTIONS:

Turn the power on.

①When the control switch is turned on, the fan will run continuously at high speed only. The power
must be on before turning the control switch on. The sensors will not work and Time Delay Switch
does not apply to this mode.

②When the control switch is turned off, the fan will run at chosen low speed on Multi-Speed switch
continuously, and boost to the high speed when the sensor detects an increase in Relative
Humidity. The fan will run at high speed for amount of time selected from the Time Delay Switch
before returning to lower speed when the Relative Humidity falls below the set point.

5