Aeromotive 14124 User Manual

AEROMOTIVE

Part # 14124

’05-’06 4.6L 3V

Ford Fuel Rail Kit

INSTALLATION INSTRUCTIONS

CAUTION:

Installation of this product requires detailed knowledge of automotive
systems and repair procedures. We recommend that this installation be carried
out by a qualified automotive technician.

Installation of this product requires handling of gasoline. Ensure you are
working in a well ventilated area with an approved fire extinguisher nearby.
Extinguish all open flames, prohibit smoking and eliminate all sources of ignition
in the area of the vehicle before proceeding with the installation.

When installing this product, wear eye goggles and other safety apparel as
needed to protect yourself from debris and sprayed gasoline.

WARNING!

The fuel system is under pressure. Do not open the fuel system until the
pressure has been relieved. Refer to the appropriate vehicle service manual for
the procedure and precautions for relieving the fuel system pressure.

Aeromotive system components are not legal for sale or use on emission controlled motor
vehicles.

Special tools needed:

Fuel supply line quick disconnect tool

This kit contains the following parts

1ea p/n 14116 Ford 4.6L 3V Fuel Rails
1ea p/n 15115 Sensor Adapter
1ea p/n 15102 Supply Adapter Tee Fitting
6ea p/n 15607 AN-8/AN-8 Cutoff Tapered Flare Fitting

:

Supplies needed:

Vehicle service manual
Fuel injector replacement O-rings
Light oil
Solvent parts cleaner
Clean shop towels

6ea AN-08 O-Ring
2ea p/n 15653 –8 Straight Hose End
1ea p/n 15654 –8 45-Degree Hose End
5ea p/n 15655 –8 90-Degree Hose End
6ft –8 Stainless Steel Braided Fuel Line
6in Rubber Vacuum Hose
2ft Hard Plastic Vacuum Hose

The following steps are typical of most installations:

1. Once the engine has been allowed to cool, disconnect the negative battery cable and relieve fuel

system pressure, referring to the appropriate vehicle service manual for the procedure on doing so.

2. Remove the air intake ducting from the throttle body and position it out of the way.

3. Note the location of and remove any vacuum lines connected to the upper intake manifold and

position them out of the way.

4. Check for any dirt or debris around the fuel injectors. If any is evident, wash it off with some solvent

parts cleaner or wipe it off with a clean shop towel.

5. Disconnect the electrical connector at each injector, making note of the location of each.

6. Carefully relieve fuel system pressure per factory service manual.

7. Disconnect the supply fuel line from the OEM fuel rails. This line is attached by a special quick

disconnect fitting which requires a special tool for removal. Place clean shop towels around the open
fuel lines to catch any gasoline that may drip out and to prevent any dirt from entering the fuel lines.

8. Remove the vacuum line from the fuel pressure sensor.

9. Remove the bolts that attach the fuel rail to the lower intake (Typically there are 4 of them).

10. Place clean shop towels around the injectors to catch any gasoline that may be spilled during their

removal. Remove the injectors from the manifold by gently pulling upward on the fuel rail / injector
assembly. Keep all injectors connected to the fuel rails. If an injector does pull out of the fuel rail, it
may spill a large amount of fuel.

11. Carefully remove the fuel injectors from the OEM fuel rail.

12. Remove the old o-rings from the fuel injectors, inspect the injectors for any dirt or debris and clean if

needed. It is suggested that the old o-rings be replaced, contact your local Ford parts dept.

13. Coat the new fuel injector o-rings with a light oil to ease installation.

14. Carefully install the new fuel injector o-rings on the injectors.

15. Place a thin coat of light oil in the fuel rail fuel injector bores and in the lower intake manifold injector

bores to help prevent cutting the o-rings during installation.

16. Carefully place the fuel injectors in the fuel rails (depending on vehicle, placing the injectors in the

intake first might ease installation). Position the electrical connector on each fuel injector to the
opposite side of the fuel rail as the mounting bracket.

17. Install the driver side fuel rail, being careful not to cut any of the o-rings during Installation.

18. Install the passenger side fuel rail, being careful not to cut any of the o-rings during installation.

19. Find suitable place in the vehicle’s engine compartment to place the Aeromotive fuel sensor adapter,

typically just in front of the driver side fuel rail.

20. Install one AN-08 o-ring on each of the six AN-8 cutoff tapered flare fittings.

21. Thread the side of the AN-8 cutoff tapered fitting with the o-ring into each of the two AN-8 ports on

the fuel pressure sensor adapter.

22. Thread the o-ring side of each four AN-08 cutoff tapered flare fittings in each end of each fuel rail.