AeroComm WISMP Users Manual

WISM+ Manual

Regulatory Compliance Section

FCC/ IC Information

Part # US/FCC CANADA/IC

WLM400 KQL-WISMP 2268C-WISMP

Antenna List

The WLM400 has been designed to operate with the antenna listed below and having a maximum gain
of 2.5dbi. The required antenna impedance is 50 ohms.

Item Part Number Mfg. Type Gain (dBi)

1

S181FL-6-PX-2450S

Nearson Dipole 2.5

• The OEM is free to choose another vendor’s antenna of like type and equal or lesser gain as
an antenna appearing in the table and still maintain compliance. Laird Technologies offers
several different options for dipole antennas. Contact your Laird sales representative for more
information.

ANTENNA REQUIREMENT

To reduce potential radio interference to other users, the antenna type and gain should be chosen so
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful
communication.

FCC/ IC MODULAR APPROVAL

The WLM400 has been granted an FCC / IC modular approval. Further RF testing by the OEM is not
needed to comply with FCC / IC standards for inentional radiators pursuant to FCC Part 15 Subpart C and
RSS-210.

The WLM400 has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 Subpart B of the FCC Rules. The OEM is responsible for verifying that their equipment complies
with the unintentional radiator limit s set fort h in Subpart B once t he WLM400 has been i nt egrat ed i nt o t hei r
product.

NOTE: The limits for a Class B digital device are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. There is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to an outlet on a circuit that is different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Portable – Portable is a classification of equipment where the user, in general, will be within 20 cm of
the transmitting antenna. Portable equipment is further broken down into two classes; within 2.5 cm of
human contact and beyond 2.5 cm. The WLM400 is not agency approved for portable applications.
Operation at distances of less than 20 cm would require additional RF exposure evaluation, including
SAR requirement according to FCC RF Exposure guideline. Contact Laird Technology for more
details.

Mobile – Mobile defines equipment where the user will be 20 cm or greater from the transmitting
equipment. The antenna must be mounted in such a way that it cannot be moved closer to the user
with respect to the equipment, although the equipment may be moved. The WLM400 has been
approved for mobile applications

OEM EQUIPMENT LABELING REQUIREMENTS

WARNING: The OEM must ensure that FCC labeling requirements are met. This includes a clearly visible

label on the outside of the OEM enclosure specifying the appropriate Laird Technology FCC identifier for
this product as well as the FCC notice below. The FCC identifiers are listed above.

Contains FCC ID:KQL- WISMP

This enclosed device complies with Part 15 of the FCC Rules, Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation

Label and text information should be in a size of type large enough to be readily legible, consistent with
the dimensions of the equipment and the label. However, the type size for the text is not required to be
larger than eight point.

CAUTION

Any changes or modifications not expressly approved by Laird Technology could void the user’s
authority to operate the equipment.