AeroBed Premier Cushioned Comfort User Manual

7993 Rev 11/09

Pump 120/DV

Instruction Manual

®

Thank you for joining the AeroBed
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed
product. Always instruct and supervise others on your bed’s proper use, maintenance and safety.

IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.

IMPORTANT SAFETY INFORMATION AND WARNINGS

WARNING: Adult supervision required for inflation, deflation, and maintenance. Follow all safety instructions to avoid serious injury.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where children can reach it. Do not use

in or around water.

WARNING: Product is for indoor use only.
WARNING: For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance

- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.

- This is not a water toy. Use as a mattress only.

- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.

- Remove all sharp objects from area where bed will be set up and used. Bed may puncture.

- Do not step or jump on bed or use as a trampoline.

- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.

- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture the bed.

- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot
objects.

- Unplug product when not in use.

- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously for more than 10 minutes. To avoid excessive heat build up in the pump, let it rest for 5 minutes between complete inflation and deflation cycles.

- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.

INFLATION

NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY
CAUSE AIR LEAKS

Remove your AeroBed from its lightweight duffle bag. Keep bag for storage.

1. Place your rolled-up bed on the floor free of obstructions or sharp objects.

2. Make certain the Quick Release Valve located next to pump is closed. Bed should be
stored with valve in the closed and latched position. If the Quick Release Valve is open,
close it by using 2 thumbs to push cover and snap into valve. Be careful to avoid
pushing valve cover to the right or left as it snaps into the valve opening.

3. Remove AC plug, cord, and control wand from plastic bag and shrink wrap.

4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical
rating: 120 VAC 60HZ 1.0A (Note: 230VAC product sold outside of North America). This
product has a polarized attachment plug (one blade is wider than the other) as a safety
feature. This plug will fit into a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Never use with an extension cord unless the plug can be fully inserted.
Do not attempt to defeat this safety feature.

5. To inflate, follow Quick Start Guide. DO NOT INTERRUPT INFLATION, PUMP WILL

AUTOMATICALLY SHUT ITSELF OFF.
CAUTION: Do not sleep on edges of the bed. Edges are less supportive and may crush

under weight.

family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination from every AeroBed product.

inflate

1

2

1

Always fully inflate mattress
before adjusting firmness level:

Press Inflate on pump: Pump will stop

automatically when bed fully inflates.

INTERRUPT INFLATION. If inflation is interrupted, press
inflate again to continue cycle.)

Use Control Wand to adjust firmness.

(Firmer/Softer)

(DO NOT

2

quickstartguide

9527 5/08

DEFLATION AND STORAGE

1. To deflate your AeroBed, open the Quick Air Release Valve. Deflation takes
approximately 60 seconds.

2. For most compact storage, close valve and follow quick start guide.
DO NOT INTERRUPT DEFLATION, PUMP WILL AUTOMATICALLY SHUT

ITSELF OFF.

3. Roll or fold the AC cord with wand control and secure it. Fold sides of bed into the
center along its length. Tightly roll and place bed in convenient carry bag for easy
storage and transport.

4. Store your AeroBed in a clean, dry place at room temperature (above 50°F/10°C). Storing
your AeroBed under 50°F (10°C) and over 100°F (38°C) may affect its performance and
transport.

deflate

1

Press Deflate on pump

Pump will stop automatically when bed
is fully deflated.

1

For automatic deflation:

quickstartguide

(Do not interrupt deflation.)

Quick Tip!

For Quick-Air Release:

1. Open the Whoosh valve and

allow air to expel

2. Close valve

3. Press deflate on pump

(Do not interrupt deflation. Pump

will auto stop when fully deflated.)

A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.

CARE AND MAINTENANCE

1. Inspect your bed prior to each use.

2. Keep your bed away from any sharp objects or obstacles with rough edges. Large cuts or snags may not be repairable and will not be covered
by your bed warranty.

3. We recommend that you do not let the plush surface of your AeroBed get wet. Repeated exposure to water or other liquids may cause
damage to the plush surface that will not be covered by your warranty. Should liquid come in contact with the plush surface, blot liquid dry
and use a damp cloth to remove any stain. Let surface air dry completely.

4. You may clean the PVC on the sides and bottom of your AeroBed with a mild dishwashing detergent or household cleaner. Do not use strong
chemicals or other compounds. Allow your bed to air dry completely after cleaning and before storing.

LIMITED EXPRESS WARRANTY

Aero Products International, Inc. (“us”) warrants to the original purchaser (“you”) that the AeroBed (“product”) is guaranteed against
defects in materials and workmanship for the following periods: pump and valve, three (3) years from date of purchase; mattress, one (1)
year from date of purchase.

OUR EXCLUSIVE OBLIGATION, AND YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY OR OTHERWISE
SHALL BE THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PARTS WHICH MAY PROVE DEFECTIVE UNDER THE CONDITIONS
OF NORMAL USE DURING THE WARRANTY PERIOD. IN THE EVENT THE PRODUCTS OR PARTS CANNOT BE REPAIRED OR
REPLACED, YOU SHALL RECEIVE A PRODUCT OF COMPARABLE VALUE AT OUR EXPENSE. AEROBED WARRANTY IS NON­TRANSFERABLE, AND IS VALID FOR THE FIRST, ORIGINAL PURCHASER FROM AN AUTHORIZED DEALER OF AEROBED PRODUCTS.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.

Exclusions

Our obligation under this limited express warranty shall not apply if our inspection shows:
A. That the product is used for other than normal indoor sleeping purposes.
B. Any product or part has been damaged by alteration.
C. Any product or part has been subject to accident, misuse, abuse or has been operated contrary to our written instructions.

®

Warranty Redemptions

You must obtain an authorization from us before returning a defective product. Call us at 1-888-462-4468 or write us at Aero Products Interna­tional, Inc., 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173 for a return authorization. The product should be carefully packaged
and delivered postage or delivery charges prepaid at the address set forth above. You are responsible for all damages incurred in shipping.

Warranty Disclaimer

EXCEPT FOR THE LIMITED EXPRESS WARRANTY SET FORTH IN THIS SECTION, OR ANY IMPLIED WARRANTIES PERMITTED UNDER
APPLICABLE LAW, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATIONS. ALL CLAIMS AGAINST US MUST BE BROUGHT
WITHIN ONE (1) YEAR FROM THE TIME THEY ARISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE DISCLAIMER MAY NOT APPLY TO YOU.

Limitation of Liability

TO THE FULLEST EXTENT PERMITTED BY LAW, SELLER SHALL NOT BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSE­QUENTIAL DAMAGES WITH RESPECT TO THE SALE OR USE OF THE PRODUCTS, INCLUDING ANY LOST REVENUES, LOSS OF USE
OR LOST PROFITS, REGARDLESS OF THE THEORY BY WHICH ANY CLAIM MAY BE BASED, INCLUDING ANY TORT, TANGIBLE PROP­ERTY DAMAGE OR STATUTORY CAUSES OF ACTION. NOTWITHSTANDING THE TERM OF ANY LIMITED OR IMPLIED WARRANTY, OR IN
THE EVENT THAT ANY LIMITED WARRANTY FAILS OF ITS ESSENTIAL PURPOSE, IN NO EVENT WILL OUR ENTIRE LIABILITY TO YOU
EXCEED THE PURCHASE PRICE ACTUALLY PAID BY YOU FOR THE PRODUCTS, OR ANY DEFECTIVE OR NONCONFORMING PORTION
THEREOF, WHICHEVER IS THE LESSER AMOUNT.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITATION DOES NOT APPLY TO ANY CLAIMS FOR PERSONAL INJURY. THIS AGREEMENT AND ANY CLAIMS AND DISPUTES
BETWEEN THE PARTIES SHALL BE GOVERNED BY AND SUBJECT TO THE INTERNAL LAWS (EXCLUSIVE OF THE CONFLICTS OF LAW
PROVISION) AND DECISIONS OF THE COURTS OF THE STATE OF ILLINOIS. THE EXCLUSIVE VENUE AND JURISDICTION FOR ALL
CLAIMS AND DISPUTES SHALL BE THE STATE OR FEDERAL COURT LOCATED IN SCHAUMBURG, ILLINOIS.

Aero Products International, Inc. neither assumes nor authorizes any representative or other person to assume any obligation or liability other than those
expressly set forth herein.

© 2010 Aero Products International, Inc. All rights reserved. 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173 USA
This product may be covered under one or more of the following U.S. and/or foreign patents: U.S. Pat. Nos. 4,977,633; 5,267,363; 5,367,726;
6,237,621; 6,508,264; 6,598,626; 6,701,559; 6,755,208; 6,986,360; 6,996,867; 7,025,576; 7,039,972; 7,165,283; 7,128,525; D464,225; D490,635;
D513,145; D594,880; CN 1809683.2; RU 2271129; SG93011; EP 0 487 641; DE 69024962.4; EP 0 947 152; DE 69233298.7; EP 1 415 576;
EP 0 605 624; DE 69230797.4; JP 3,419,774; TW 62301; AU 731613; BR PI9710873-1; CN 97196557.9; HK 1025374; MX 216898; NZ 334203;
SG 61207; JP 2010828; EP 1 359 325; MX 242683; AU 319268; ECD 00819289; ECD 00906920
Other U.S. and foreign patents pending.
Made in China.

www.aerobed.com