AeroBed EcoLite User Manual

8101 Rev 3/10

Pump HB177 NiCd/Hi805AB

Instruction Manual

Thank you for joining the AeroBed® family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed product. You are
about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed product.
Always instruct and supervise others on your bed’s proper use, maintenance and safety.

IMPORTANT SAFETY INFORMATION AND WARNINGS

SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

IMPORTANT: Preparation of your product requires no tools. Use of tools may damage your bed.

Rechargeable Pump - For outdoor use.

WARNING: The Air Release Valve is made of several small parts which could pose a choking hazard.

Keep all parts away from children under 6 years of age.

WARNING: Pump is not a toy - children must be supervised at all times.
WARNING: Risk of electric shock. Do not expose to rain. Store indoors.

- Pump charger is an electrical device. Do not use in or around water.

- Charger to be used indoors only.

- Do NOT place pump or charger where they could fall or be pulled into the water.

- Not recommended for children under 6 years of age.

- The pump contains nickel-cadmium batteries.

- The pump should not be incinerated.

- The pump should not be overcharged or reverse charged.

- The pump batteries are not replaceable. Do not attempt to replace them.

- Do NOT charge the NiCd battery pump with any other charger than the one provided with the pump.

- Do NOT attempt to dissemble, repair, or service pump. No user serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Thrid Floor, Schaumburg, IL 60173,
1-888-462-4468 for repair or servicing information.

WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:

- Bed supports a maximum weight of 300 lbs. per person.

- This is not a water toy. Use as a mattress only.

- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer
serious or fatal injury through suffocation, falling from or rolling off the bed or becoming trapped.

- Use on flat surfaces only. Bed may tip over on uneven surfaces.

- Inflate bed fully. Partially inflated mattresses can cause suffocation.

- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near
pointed/sharp items or surfaces. Bed may puncture.

- Do not step or jump on bed or use as a trampoline.

- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place
it near or against heaters, open flame, or other hot objects.

- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously (refer to warning statement on side of pump).
To avoid excessive heat build-up in the pump, let it rest for 10 minutes between complete inflation cycles.

RECHARGEABLE Ni-Cd PUMP

IMPORTANT: PUMP MUST BE CHARGED FOR 24 HOURS PRIOR TO THE FIRST INFLATION. Use the AC adapter to charge your new Aero pump

for 24 hours. For maximum performance, be sure to fully discharge pump before recharging. After initial charge and use, charge pump for 12 HOURS
at a time. Charging your pump for periods shorter or longer than 12 hours will substantially decrease the life of your Ni-Cd pump. In an emergency, a 3
hour charge will provide one inflation, however, continued charging for 3 hour periods will substantially decrease the life of your Ni-Cd pump.

IMPORTANT: ALWAYS store pump and charger in a cool, dry place. DO NOT allow pump or charger to get wet. Allowing pump and/or charger

to get wet will void your warranty.

TO CHARGE / RECHARGE:

a) First, remove pump and charger from protective plastic shipping wraps.
b) Insert the charger’s mini-plug in the hole.
c) Third, plug the charger unit into any standard 110V (or 220V depending on your local service) electrical outlet and let it charge for 12 hours
(24 hours on initial charge).

NOTE: For best pump performance, you must completely drain the charge from your pump prior to recharging. For directions, see discharge section below.

Prior To Inflation:
a) Unplug the pump after it has been charged for 12 hours (24 hours on initial charge).
b) Remove charger unit from the electrical outlet.

NOTE: Pump will not run while charger is plugged into an electrical outlet.

To Discharge:
a) Place pump on valve as if to inflate product.
b) Allow pump to run until the pump motor dies down.

NOTE: When properly used, your pump will hold a full charge for approximately 90 days. When storing pump for longer than 90 days, fully discharge and

recharge pump every 120 days. This will help maximize pump life.

WARNING: PUMP SHOULD ONLY BE USED WITH AERO ADAPTER PROVIDED. DO NOT USE WITH ANY OTHER ADAPTER.

IMPORTANT: PUMP CONTAINS NICKEL-CADMIUM BATTERIES. BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.

INFLATION

Note: Product must be at room temperature prior to inflating or it may cause air leaks.

1. Place your rolled up bed on the floor or other surface free of obstructions or sharp objects.

2. Remove pump from protective plastic shipping wraps.

3. Open protective cap on valve by turning counter-clockwise (see figure A). Press the side port of the pump into the valve, then turn pump to “on” position
(see figure B).

4. In minutes, your bed will be inflated to the firmest capacity. Detach pump and close valve by turning clockwise.Turn pump to “off” position.

5. Lie on bed and check the firmness. If you want the bed to be firmer, open protective cap by turning counter-clockwise.
Press the side port of the pump into the valve, reinflate the bed until the desired level of firmness is achieved.

6. Replace valve cap.

A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.

A

B

inflation port

UNIVERSAL ADAPTERS

For use with other air-filled products.

1. Attach universal adapter to end of pump by pushing until adapter locks into position.

2. Additional adapters are included for use with multiple sized valve openings.

3. Use pump with other products.

DEFLATION AND STORAGE

1. To deflate your AeroBed, open the valve located next to the pump (see figure C).

2. For most compact storage, open protective cap by turning counter-clockwise.

3. Press the port on top of the pump into the valve and then turn pump to “on” position (see figure D).

4. Your bed will begin to deflate, once deflated turn pump to “off” position.

5. Roll the bed completely until all the air is expelled. When the bed is completely rolled, replace the valve cap by turning clockwise.

6. Fold sides of bed into the center along its length (see figure E). Tightly roll and place in convenient carry bag for easy transport and storage.

C

D

CARE AND MAINTENANCE

1. Inspect your bed prior to each use.

2. Keep your bed away from any sharp objects or obstacles with rough edges. Large cuts or snags may not be repairable and will
not be covered by your bed warranty.

3. We recommend that you do not let the plush surface of your AeroBed get wet. Repeated exposure to water or other liquids
may cause damage to the plush surface that will not be covered by your warranty. Should liquid come in contact with the plush
surface, blot liquid dry and use a damp cloth to remove any stain. Let surface air dry completely.

4. You may clean the PVC on the sides and bottom of your AeroBed with a mild dishwashing detergent or household cleaner. Do not use strong
chemicals or other compounds. Allow your bed to air dry completely after cleaning and before storing.

LIMITED EXPRESS WARRANTY

Aero Products International, Inc. (“us”) warrants to the original purchaser (“you”) that the AeroBed (“product”) is guaranteed against defects
in materials and workmanship for the following periods: pump and valve, two (2) years from date of purchase; mattress, one (1) year from
date of purchase.

OUR EXCLUSIVE OBLIGATION, AND YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY OR OTHERWISE
SHALL BE THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PARTS WHICH MAY PROVE DEFECTIVE UNDER THE
CONDITIONS OF NORMAL USE DURING THE WARRANTY PERIOD. IN THE EVENT THE PRODUCTS OR PARTS CANNOT BE
REPAIRED OR REPLACED, YOU SHALL RECEIVE A PRODUCT OF COMPARABLE VALUE AT OUR EXPENSE. AEROBED
WARRANTY IS NON-TRANSFERABLE, AND IS VALID FOR THE FIRST, ORIGINAL PURCHASER FROM AN AUTHORIZED
DEALER OF AEROBED PRODUCTS. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Exclusions

Our obligation under this limited express warranty shall not apply if our inspection shows:
A. That the product is used for other than normal indoor sleeping purposes.
B. Any product or part has been damaged by alteration.
C. Any product or part has been subject to accident, misuse, abuse or has been operated contrary to our written instructions.

®

deflation port

E

Warranty Redemptions

You must obtain an authorization from us before returning a defective product. Call us at 1-888-462-4468 or write us at Aero Products International, Inc., 1834 Walden
Office Square, Third Floor, Schaumburg, IL 60173 for a return authorization. The product should be carefully packaged and delivered postage or delivery charges
prepaid at the address set forth above. You are responsible for all damages incurred in shipping.

Warranty Disclaimer

EXCEPT FOR THE LIMITED EXPRESS WARRANTY SET FORTH IN THIS SECTION, OR ANY IMPLIED WARRANTIES PERMITTED UNDER APPLICABLE LAW,
SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATIONS. ALL CLAIMS AGAINST US MUST BE BROUGHT WITHIN ONE (1) YEAR FROM THE TIME
THEY ARISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE DISCLAIMER MAY NOT APPLY
TO YOU.

Limitation of Liability

TO THE FULLEST EXTENT PERMITTED BY LAW, SELLER SHALL NOT BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
WITH RESPECT TO THE SALE OF USE OF THE PRODUCTS, INCLUDING ANY LOST REVENUES, LOSS OF USE OR LOST PROFITS, REGARDLESS OF THE
THEORY BY WHICH ANY CLAIM MAY BE BASED, INCLUDING ANY TORT, TANGIBLE PROPERTY DAMAGE OR STATUTORY CAUSES OF ACTION. NOTWITH­STANDING THE TERM OF ANY LIMITED OR IMPLIED WARRANTY, OR IN THE EVENT THAT ANY LIMITED WARRANTY FAILS OF ITS ESSENTIAL PURPOSE, IN
NO EVENT WILL OUR ENTIRE LIABILITY TO YOU EXCEED THE PURCHASE PRICE ACTUALLY PAID BY YOU FOR THE PRODUCTS, OR ANY DEFECTIVE OR
NONCONFORMING PORTION THEREOF, WHICHEVER IS THE LESSER AMOUNT.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITATION DOES NOT APPLY TO ANY CLAIMS FOR PERSONAL INJURY. THIS AGREEMENT AND ANY CLAIMS AND DISPUTES BETWEEN THE
PARTIES SHALL BE GOVERNED BY AND SUBJECT TO THE INTERNAL LAWS (EXCLUSIVE OF THE CONFLICTS OF LAW PROVISION) AND DECISIONS OF
THE COURTS OF THE STATE OF ILLINOIS. THE EXCLUSIVE VENUE AND JURISDICTION FOR ALL CLAIMS AND DISPUTES SHALL BE THE STATE OR
FEDERAL COURT LOCATED IN SCHAUMBURG, ILLINOIS.

Aero Products International, Inc. neither assumes nor authorizes any representative or other person to assume any obligation or liability other than those
expressly set forth herein.

© 2010 Aero Products International, Inc. All rights reserved. 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173 USA
This product may be covered under one or more of the following U.S. and/or foreign patents: U.S. Pat. Nos. 4,977,633; 5,267,363; 5,367,726; 6,237,621;
6,508,264; 6,598,626; 6,701,559; 6,755,208; 6,986,360; 6,996,867; 7,025,576; 7,039,972; 7,165,283; 7,128,525; 7,644,724; D464,225; D490,635; D513,145;
D594,880; CN 1809683.2; RU 2271129; SG93011; EP 0 487 641; DE 69024962.4; EP 0 947 152; DE 69233298.7; EP 1 415 576; EP 0 605 624;
DE 69230797.4; JP 3,419,774; TW 62301; AU 731613; BR PI9710873-1; CN 97196557.9; HK 1025374; MX 216898; NZ 334203; SG 61207; JP 2010828;
EP 1 359 325; MX 242683; AU 319268; ECD 00819289; ECD 00906920
Other U.S. and foreign patents pending.
Made in China.

www.aerobed.com