AeroBed 6340661 Instruction manual

8034UK Rev. 10/07

®

AeroBed

Instruction Manual

and Guarantee

© 2007 Aero Products International Ltd., P.O.Box 43787, London, W14 9YN GB

Made in China.

AeroBed

®

Thank you for purchasing your luxury AeroBed®. You can expect premium quality,
innovation and durability from every

You are about to enjoy the comfort of the

AeroBed®product.

AeroBed®, the finest alternative sleeping

system available anywhere. It is your responsibility to read and always follow the
safety, care and maintenance instructions for your new

AeroBed®product. Always

instruct and supervise others on the proper use, maintenance and safety of your
bed.

IMPORTANT: Preparation of your bed requires no tools.Use of tools may damage
your bed.

Read, follow and retain this instruction manual for future reference.

IMPORTANT SAFETY INFORMATION AND

WARNINGS

!

— WARNING: Adult supervision required for inflation, deflation and maintenance.

Follow all safety instructions to avoid serious injury.

!

— WARNING: This is an electrical product - not a toy.To avoid risk of fire, burns,

injury, and shock, it should not be played with or placed where small children
can reach it. Do not use in or around water.

— WARNING: Product is for indoor use only.

!

— This is not a water toy.Use as a mattress only.
— This mattress is not intended for infants or persons with limited mobility.They

may roll off of the mattress and become entrapped between the mattress and a
wall.

— Remove all sharp objects from area where bed will be set up and used. Bed may

puncture.

— Do not step or jump on bed or use as a trampoline.
— Place bed in a safe area before use, making sure that there are no sharp edges,

steps, drops, or breakable items nearby.Use on flat surfaces only. Bed may tip
over on uneven surfaces.

— Do not use this bed on abrasive surfaces or near pointed/sharp items or

surfaces.Protr uding objects may puncture the bed.

— This bed is made of plastic and therefore may melt or burn if it comes in contact

with any flame or heat source. Do not place it near or against heaters, open
flame or other hot objects.

— Unplug product when not in use.
— If the supply cord is damaged, it must be replaced by Aero Products, our service

agent or similarly qualified persons in order to avoid a hazard.

— Pump is not intended for continuous use.Pump may stop working or overheat if

it is used f
than 10 min

xtended per

or e

utes.To avoid excessive heat build up in the pump, let it rest for 5

iods of time

minutes between complete inflation and deflation cycles.

— Do not attempt to dissemble, repair, or service the pump. No serviceable parts

are contained inside. Contact
London

W14 9YN, for repair or servicing information.

Aero Products International, P.O.Box 43787,

. Do not use pump continuously for more

INFLATION

1. Remove your AeroBed®from its lightweight duffle bag. Keep bag for storage.
NOTE: Bed must be at room temperature prior to inflating.

2. Remove AC plug, cord and remote control from plastic bag and shrink wrap.
Because this is an electrical device, do not use this in or around water.

3. Plug pump into any standard polarized 220-240 volt AC electrical outlet. (

Note:

this product is rated at 230V ~ 50Hz, 0.5A. 110-volt product sold outside
Europe). Never use with an extension cord unless the plug can be fully inserted.

4. Manually slide lever to inflate position. Click to lock lever
into position.

5. Push and hold button on remote control for
approximately 60 seconds to inflate your

AeroBed®to

the full (firmest) capacity. Bed will not over-inflate.

6. Bed is ready to use

7. Lie on the bed to test the fir mness. For a firmer bed,
make sure the lever is in the inflate position and press
the button on the remote control. For a softer bed,
manually slide the lever to the middle position on the
pump to expel air. Upon reaching the desired firmness
level, make sure to lock the lever back into the inflate
position.

DEFLATION AND STORAGE

1. Make sure the bed is plugged into an electrical outlet
prior to deflation.

2. To deflate your
locks into the deflate position.Then push and hold the
button on the remote control until all air is expelled from
the bed. Pump deflates bed in approximately 60 seconds.

3. Roll or fold the AC cord with remote control and secure it.
Fold sides of bed into the center along its length.Tightly
roll your
completely rolled, place it into the lightweight duffle bag
for storage.

4. Slide the duffel bag over your

AeroBed®in a clean dry place at room temperature

(above 50°F/10° C). Storing your
(10° C) and over 100° F (38° C) may affect its performance and will not be
co

v

ered under guarantee.

AeroBed®slide lever on pump until it

AeroBed®around the pump.When the bed is

AeroBed®. Store your

AeroBed®under 50° F

1

2