AeroBed 109 DC User Manual

7986 Rev 09/07

109 Pump

Instruction Manual

Thank you for joining the Aero® Sport family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination from every AeroSport
product. You are about to enjoy the comfort of an AeroSport bed. It is your responsibility to read and always follow the safety, care, and maintenance instructions for your new
AeroSport product. Always instruct and supervise others on your bed’s proper use, maintenance, and safety.

IMPORTANT: Preparation of your AeroSport bed requires no tools. Use of tools may damage your bed.

IMPORTANT SAFETY INFORMATION AND WARNINGS

Bed / Rechargeable Pump

WARNING: Adult supervision required for inflation, deflation, and maintenance. This is not a lifesaving device. Do not leave children unattended in or around water.
WARNING: This bed is not designed for use by children under 3 years of age. Children under the age of 3 may suffer serious or fatal injury through suffocation, falling from the

bed or becoming trapped between the bed and a wall or other objects.

WARNING: Product is for indoor use only.
WARNING: For household / residential use only.

- This is not a water toy. Use as a mattress only.

- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.

- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture bed. Remove all sharp objects from area where bed will be
set up and used.

- Product is intended for use as an indoor bed only. Do not step or jump on bed or use as a trampoline. Bed may puncture.

- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.

- Standing, jumping, or walking on the bed may result in injury and/or damage the bed. Do not jump, stand, or walk on this bed. You can hurt yourself or damage the bed if you do.

- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot
objects.
WARNING: This is an electrical product - not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where small children can reach it.
Do not use in or around water.

- Pump and Pump charger are electrical devices. Do not use in or around water. DO NOT place pump where it could fall or be pulled into the water.

- Unplug adapter when not in use.

- Pump not recommended for use by children under six (6) years of age.

- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.

RECHARGEABLE Ni-Cd PUMP

IMPORTANT: PUMP MUST BE CHARGED FOR 24 HOURS PRIOR TO THE FIRST INFLATION. Use the AC adaper to charge your new AeroSport pump

for 24 hours. For maximum performance, be sure to fully discharge pump before recharging. After initial charge and use, charge pump for 12 HOURS
at a time. Charging your pump for periods shorter or longer than 12 hours will substantially decrease the life of your Ni-Cd pump. In an emergency, a
3 hour charge will provide one inflation, however, continued charging for 3 hour periods will substantially decrease the life of your Ni-Cd pump.
IMPORTANT: ALWAYS store pump and charger in a cool, dry place. DO NOT allow pump or charger to get wet. Allowing pump and/or charger to
get wet will void your warranty.

TO CHARGE / RECHARGE:

a) First, remove pump and charger from box.
b) Second, remove tiny rubber plug from hole on the back of the pump. Insert the charger’s mini-plug in the hole.
c) Third, plug the charger unit into any standard 110V (or 220V depending on your local service) electrical outlet and let it charge for 12 hours
(24 hours on initial charge).

NOTE: For best pump performance, you must completely drain the charge from your pump prior to recharging. For directions, see discharge section below.
Prior To Inflation:

a) Unplug the pump after it has been charged for 12 hours (24 hours on initial charge).
b) Remove charger unit from the electrical outlet and the mini-plug from the pump.
c) Re-insert the tiny rubber plug into the hole on the back of the pump.

NOTE: Pump will not run while charger is plugged into an electrical outlet.
To Discharge:

a) Place pump on valve as if to inflate product.
b) Allow pump to run until the pump motor dies down.
NOTE: When properly used, your pump will hold a full charge for approximately 90 days. When storing pump for longer than 90 days, fully discharge
and recharge pump every 120 days. This will help maximize pump life.

TO USE PUMP INSTANTLY WITHOUT HAVING TO RECHARGE THE NI-CD BATTERIES:

a) First, remove the tiny rubber plug from hole on the back side of the pump.
b) Second, insert the 12-volt DC adapter mini-plug into the hole.
c) Third, plug the DC power cord into a standard 12-volt DC automobile cigarette lighter or accessory 12-volt outlet and turn ignition to the accessory portion.
Do not operate pump while engine is running.
d) When the bed is fully inflated detach pump and unplug the 12-volt adapter from the lighter.
WARNING: Do not leave the pump plugged into the cigarette lighter or 12-volt DC outlet, doing so could damage the life of the Ni-Cd batteries. PUMP
SHOULD ONLY BE USED WITH AERO ADAPTERS PROVIDED. DO NOT USE WITH ANY OTHER ADAPTERS. To avoid against risk of fire, electric shock or
injury to persons, read all instruction before using.
CAUTION! Do not incinerate or disassemble this pump, it could result in an explosion or release of toxic materials. Do not short circuit the pump, it may cause
burns.

IMPORTANT: PUMP CONTAINS NICKEL-CADMIUM BATTERIES. BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.

INFLATION

NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.

1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.

2. Make certain the Quick Release Valve located at the head of the bed is closed. If the Air Release Valve is open, close it by using 2 thumbs to push
cover and snap into valve. Be careful to avoid pushing valve cover to the right or left as it snaps into the valve opening.

This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs

3. Remove the protective plastic cap from the valve by turning counter clockwise. Open the protective rubber cap at the end of the pump. Press the mouth
of the pump into position on the inflation/Release Valve and turn clockwise until it locks.

4. A one-quarter turn clockwise automatically starts inflation.

5. At approximately 60 seconds, a high pitch whine of the pump will signal the bed is inflated to full (firmest) capacity. Bed will not over-inflate.

8. Detach pump by turning counter clockwise. Lie on bed and check the firmness. If you want your bed to be softer, depress the botton in the center
of the valve. If the bed becomes too soft, reattach the pump and reinflate the bed until the desired level of firmness is achieved.
IMPORTANT: Be sure to close the protective valve cap after inflation.

DEFLATION AND STORAGE

1. Open the Quick Air Release Valve cover at the head of the bed to release the air.

2. Fold sides of bed into the center along its length. Tightly roll your bed towards the Quick Air Release Valve at the end of the bed.

3. Roll the bed completely until all air is expelled. When the bed is completely rolled, push the Quick Air Release Valve closed and locked for its
next use.

4. Slide the duffel bag over your AeroBed. Store your bed and pump until its next use.

CARE AND MAINTENANCE

1. Inspect your bed prior to each use.

2. Keep your bed away from any sharp objects or obstacles with rough edges. Large cuts or snags may not be repairable and will not be covered
by your bed warranty.

3. When not in use, store your bed in a clean, dry place out of extreme temperatures. Note: Bed must be at room temperature prior to inflating or
it may cause air leaks.

4. In case of incidental damage to your bed, a repair patch has been included. Please follow repair instructions carefully.

CLEANING

We recommend that you do not let the plush surface on top of your bed get wet. Repeated exposure to water or other liquids may cause damage to the plush surface
that will not be covered by your warranty. Should liquid come in contact witht the plush surface, blot liquid dry and use a damp cloth to remove any stains. Let surface
air dry completely.
You may clean the PVC on the sides and bottom of your bed with a mild dishwashing detergent or household cleaner. Do not use strong chemicals or other
compounds. Allow your bed to air dry completely after cleaning and before storing.

TROUBLESHOOTING

Very rarely, your Aero

®

Sport bed may fail to inflate properly. Should this occur, please use the following check list.

1. Check to make sure your pump is fully charged.

2. If your bed deson’t appear to be inflating:
First, make sure the Quick Air Release Valve is closed.
If the valve is open, close it by using 2 thumbs to push cover firmly into valve. Be careful to avoid pushing valve cover to
right or left as it snaps into valve opening.

3. If air leakage from the Quick Air Release Valve occurs:
Carefully, inspect the soft round gasket on the inside of Quick Air Release Valve cover. Make sure there is no dirt or debris,
cuts, nicks, or tears to the gasket. If there is dirt or debris; clean and use. If cut, nicked or torn, call our Customer Service
Center or visit our website to order a replacement part.

4. If trouble persists, please phone our Customer Service Center for assistance.
U.S.: 1-888-462-4468
Monday through Friday, 9 AM to 5 PM Central Standard Time

Canada: 1-888-702-8281
or visit our website at: www.aerobed.com

LIMITED EXPRESS WARRANTY

Aero Products International, Inc. (“us”) warrants to the original purchaser (“you”) that the AeroBed (“product”) is guaranteed against defects in materials and
workmanship for the following periods: pump and valve, one (1) year from date of purchase; mattress, one (1) year from date of purchase.

OUR EXCLUSIVE OBLIGATION, AND YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY OR OTHERWISE SHALL BE THE
REPAIR OR REPLACEMENT OF ANY PRODUCT OR PARTS WHICH MAY PROVE DEFECTIVE UNDER THE CONDITIONS AND DURING THE PERIODS
DESCRIBED ABOVE AT OUR SOLE COST AND EXPENSE. IN THE EVENT THE PRODUCTS OR PARTS CANNOT BE REPAIRED OR REPLACED, YOU
SHALL RECEIVE A FULL REFUND OF THE PURCHASE PRICE AT OUR OPTION. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Exclusions

Our obligation under this limited express warranty shall not apply if our inspection shows:
A. That the product is used for other than normal indoor sleeping purposes.
B. Any product or part has been damaged by alteration.
C. Any product or part has been subject to accident, misuse, abuse or has been operated contrary to our written instructions.

Warranty Redemptions

You must obtain an authorization from us before returning a defective product. Call us at 1-888-702-8281 or write us at Aero Products International, Inc., 1834
Walden Office Square, Third Floor, Schaumburg, IL 60173 for a return authorization. The product should be carefully packaged and delivered postage or delivery
charges prepaid at the address set forth above. You are responsible for all damages incurred in shipping.

Warranty Disclaimer

EXCEPT FOR THE LIMITED EXPRESS WARRANTY SET FORTH IN THIS SECTION, OR ANY IMPLIED WARRANTIES PERMITTED UNDER APPLICABLE LAW,
SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATIONS. ALL CLAIMS AGAINST US MUST BE BROUGHT WITHIN ONE (1) YEAR FROM THE TIME
THEY ARISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE DISCLAIMER MAY NOT APPLY
TO YOU.

Limitation of Liability

TO THE FULLEST EXTENT PERMITTED BY LAW, SELLER SHALL NOT BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
WITH RESPECT TO THE SALE OF USE OF THE PRODUCTS, INCLUDING ANY LOST REVENUES, LOSS OF USE OR LOST PROFITS, REGARDLESS OF THE
THEORY BY WHICH ANY CLAIM MAY BE BASED, INCLUDING ANY TORT, TANGIBLE PROPERTY DAMAGE OR STATUTORY CAUSES OF ACTION. NOTWITH­STANDING THE TERM OF ANY LIMITED OR IMPLIED WARRANTY, OR IN THE EVENT THAT ANY LIMITED WARRANTY FAILS OF ITS ESSENTIAL PURPOSE,
IN NO EVENT WILL OUR ENTIRE LIABILITY TO YOU EXCEED THE PURCHASE PRICE ACTUALLY PAID BY YOU FOR THE PRODUCTS, OR ANY DEFECTIVE
OR NONCONFORMING PORTION THEREOF, WHICHEVER IS THE LESSER AMOUNT.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITATION DOES NOT APPLY TO ANY CLAIMS FOR PERSONAL INJURY. THIS AGREEMENT AND ANY CLAIMS AND DISPUTES BETWEEN THE
PARTIES SHALL BE GOVERNED BY AND SUBJECT TO THE INTERNAL LAWS (EXCLUSIVE OF THE CONFLICTS OF LAW PROVISION) AND DECISIONS OF
THE COURTS OF THE STATE OF ILLINOIS. THE EXCLUSIVE VENUE AND JURISDICTION FOR ALL CLAIMS AND DISPUTES SHALL BE THE STATE OR
FEDERAL COURT LOCATED IN SCHAUMBURG, ILLINOIS.

Aero Products International, Inc. neither assumes nor authorizes any representative or other person to assume any obligation or liability other than those expressly set
forth herein.
© 2007 Aero Products International, Inc. All rights reserved. 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173 USA
This product may be covered under one or more of the following U.S. and/or foreign patents: U.S. Pat. Nos. 4,977,633; 5,267,363; 5,367,726; 6,237,621; 6,508,264;
6,598,626; 6,701,559 ; 6,755,208; 6,986,360; 6,996,867; 7,025,576; 7,039,972; 7,165,283; D464,225; D490,635; D513,145; CN 1809683.2; RU 2271129;
SG93011; EP 0 487 641 ; DE 69024962.4; EP 0 947 152; DE 69233298.7; EP 0 605 624 ; DE 69230797.4; JP 3,419,774; TW 62301; AU 731613; BR PI9710873-1;
CN 97196557.9 ; HK 1025374; MX 216898; MX 242683; NZ 334203; SG 61207; JP 2010828; EP 1 359 325; EP 1 415 576. Other U.S. and foreign patents pending.
Made in China.