Aero Pillowtop AeroBed User guide
English 1Français 14 Español 7
Manual de Instrucciones
Mode d'emploi
Pillowtop AeroBed
®
Instruction Manual
© Aero Products International, Inc., 1225 Karl Court, Wauconda, IL 60084-1098 USA
Made in China.
WARRANTY DEPARTMENT
AERO PRODUCTS INTERNATIONAL, INC.
1225 KARL COURT
WAUCONDA IL 60084-1098
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
PLACE
STAMP
HERE
9076 Rev. 5/02 N &I
Questions?
Please visit our web site anytime at
www.thinkaero.com
or
Call our Customer Service Department at
1-888-462-4468
(operators are available Monday - Friday, 9 AM - 5 PM CST)
1
English
Pillowtop AeroBed
®
Thank you for joining the aero®family by purchasing one of our upscale products.
You can expect topnotch quality, innovation and imagination from every aero product.
You are about to enjoy the comfort of the Pillowtop AeroBed, the finest alternative
sleeping system available anywhere. It is your responsibility to read and always
follow the safety, care and maintenance instructions for your new aero product.
Always instruct and supervise others on the proper use, maintenance and safety of
your bed.
IMPORTANT: Preparation of your Pillowtop AeroBed requires no tools. Use of tools
may damage your bed.
Read, follow and retain this instruction manual for future reference.
IMPORTANT SAFETY INFORMATION
AND WARNINGS
— WARNING: Adult supervision required. Follow all safety instructions to avoid
serious injury.
— WARNING: This is an electrical product - not a toy. To avoid risk of fire, burns,
injury, and shock, it should not be played with or placed where small children can
reach it. Do not use in or around water.
—Remove all sharp objects from area where bed will be set up and used.
—Product is intended for use as an indoor bed only. Do not step or jump on bed or
use as a trampoline. Bed may puncture.
—Place bed in a safe area before use, making sure that there are no sharp edges,
steps, drops, or breakable items nearby. Use on flat surfaces only. Bed may tip
over on uneven surfaces.
—Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces.
Protruding objects may puncture the bed.
—This bed is made of plastic and therefore may melt or burn if it comes in contact
with any flame or heat source. Do not place it near or against heaters, open flame
or other hot objects.
—Unplug product when not in use.
—Do not attempt to dissemble, repair, or service the pump. No serviceable parts
are contained inside. Contact Aero Products International, Inc. at 1225 Karl Court,
Wauconda, IL 60084, for repair or servicing information.
!
!
May also include:
aero
www.thinkaero.com
or
1-888-462-4468
(Mon.- Fri. 9AM – 5PM CST)
• Durable carry bag
Pillowtop AeroBed®
Secure Seal™
Quick Release Valve
(Centered on bottom chamber)
Internal coil
construction
14' cord
Quilted, plush Pillowtop chamber
Powerful recessed AC Pump
One T ouch® Comfort Control
3
English
DEFLATION AND STORAGE
1. Make sure the bed is unplugged from the electric outlet
prior to deflation.
2. Open the Secure Seal™ Quick Release Valve at the foot
of the bed to release the air.
3. Roll or fold the AC cord with One Touch
®
Comfort Control
block and secure it. Fold sides of bed into the center along
its length. Tightly roll your Pillowtop AeroBed
®
around the
pump towards the Quick Release Valve end.
4. Roll the bed completely until all air is expelled. When
the Bed is completely rolled, push the Quick Release Valve
closed until it locks.
5. Slide the duffel bag over your Pillowtop AeroBed. Store
your bed until its next use.
CARE AND MAINTENANCE
1. Inspect your Pillowtop AeroBed prior to each use.
2. Keep your Pillowtop AeroBed away from any sharp objects. Large cuts or snags
may not be repairable and will not be covered by your warranty.
3. When not in use, store your Pillowtop AeroBed in its duffle bag, in a clean, dry
place out of extreme temperatures. Product must be at room temperature prior
to inflating.
4. Do not store your Pillowtop AeroBed folded inside sofa beds or roll-aways. This
may cause damage to your Pillowtop AeroBed that will not be covered under
your warranty.
5. In case of incidental damage to your bed, a repair kit has been included. Please
follow repair instructions carefully.
CLEANING
We recommend that you do not let the plush surface of your Pillowtop AeroBed get
wet. Repeated exposure to water or other liquids may cause damage to the plush
surface that will not be covered by your warranty. Should liquid come in contact with
the plush surface, blot liquid dry and use a damp cloth to remove any stain. Let
surface air dry completely.
You may clean the PVC on your Pillowtop AeroBed with a mild dishwashing
detergent or household cleaner. Do not use strong chemicals or other compounds.
Allow your bed to air dry completely after cleaning and before storing.
If a mattress cover is included, you may machine wash your cover in warm water
using a mild soap or detergent. Tumble dry on LOW HEAT.
English
2
INFLATION
Remove your Pillowtop AeroBed®from its lightweight duffel bag. Keep bag for storage.
Note: Product must be at room temperature prior to inflating.
1. Place your rolled up bed on the floor or other surface free of obstructions or
sharp objects.
2. Make certain the Secure Seal™ Quick Release Valve located at the foot of the
bed is closed. Bed should be stored with valve in the closed and latched position.
If the Quick Release Valve is open, close it by using 2 thumbs to push cover and
snap into valve. Be careful to avoid pushing valve cover to the right or left as it
snaps into the valve opening.
3. Remove AC plug, cord and One Touch
®
Comfort Control from plastic bag and
shrink wrap.
4. Plug into any standard polarized 110 Volt AC electrical outlet.
(NOTE: 220/240 Volt product sold outside of North America.)
This product has a polarized attachment plug (one blade is wider than the other)
as a safety feature. This plug will fit into a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. Never use with an extension cord unless the plug can be
fully inserted. Do not attempt to defeat this safety feature.
5. Push and hold the button of the One Touch Comfort
Control for approximately 60 seconds to inflate the
Pillowtop AeroBed to full (firmest) capacity. Bed will not
over-inflate.
6. Attach the One Touch Comfort Control block to the
inflator by sliding it over the rubber nipple.
7. Lie on the bed to adjust the firmness to your desired level.
a. To make the bed softer, depress the One Touch
Comfort Control block (not the button) and rubber
nipple together.
b. To make the bed firmer, depress only the button of
the One Touch Comfort Control.
This is the closed position. Open Quick Release Valve
aero
aero
aero
Close Valve Using 2 Thumbs
60 sec
Inflation
English
4 5
English
TROUBLESHOOTING
Very rarely, your Pillowtop AeroBed®may fail to inflate properly. Should this occur,
please use the following check list.
1. If your Pillowtop AeroBed doesn’t appear to be inflating:
First, make sure the Secure Seal™ Quick Release
Valve is closed and locked securely.
If the valve is open, close it by using 2 thumbs to push
cover firmly into valve. Be careful to avoid pushing valve
cover to the right or left as it snaps into valve opening.
2. If air leakage from the Secure Seal™ Quick Release Valve occurs:
Carefully inspect the soft round gasket on inside of Quick Release Valve cover.
Make sure there is no dirt or debris, cuts, nicks or tears to the gasket. If there is
dirt or debris; clean and use. If cut, nicked or torn, call our Customer Service
center or visit our website to order a replacement part.
3. If trouble persists, please phone our Customer Service center for assistance.
U.S. and Canada: 1-888-462-4468
Monday through Friday, 9 AM to 5 PM Central Standard Time
Or visit our website at : www.thinkaero.com
LIMITED WARRANTY
Aero Products International, Inc. warrants to the original purchaser only when the
Pillowtop AeroBed
®
is used for normal indoor sleeping purposes, that the mattress
will be fully guaranteed against defects in material and workmanship for a period of
one (1) year from the date of purchase, provided further that the Pillowtop AeroBed
has been operated according to the provided instructions. (Included in your
purchase is a repair kit with instructions.)
The motor (exclusive of the controller) will be guaranteed to the original purchaser
against defects in materials and workmanship for a period of one (1) year from the
date of purchase provided the motor has been operated according to the
instructions.
Our obligation under this warranty shall be limited to the repair or exchange of any
part or parts which may prove defective under the conditions and during the periods
described above.
Our obligation under this warranty shall not apply if our inspection shows:
A. Any product or part that has been damaged by alteration.
B. Any product or part that has been subject to accident, misuse, abuse or has
been operated contrary to Aero Products International, Inc. instructions for the
product.
All purchasers must obtain an authorization from Aero Products International, Inc.
before returning a defective product. The product should be carefully packaged and
delivered postage or delivery charges prepaid. The customer shall be responsible for
all damages incurred in shipping.
Loading...