Page 1
Wall Switch
(ZWA038-A)
Page 2
1
Command Class Name
Version
Required Security Class
Security 2
V1
none
Transport Service
V2
none
Multi Channel Association
V4
highest granted
Engineering Specifications
This product can be operated in any Z-Wave™ network with other Z-Wave Plus™ certified devices from other
manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to
increase reliability of the network. Each module is designed to act as a repeater, which will re-transmit a radio
frequency (RF) signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received
at its intended destination. ZWA038-A is a security enabled Z-Wave Plus™ device. A security Enabled Z-Wave Plus™
Controller must be used in order to fully utilize the product.
1 Library and Command Classes
1.1 Embedded SDK
v 7.13.9
1.2 Device Type
Generic Type: Switch Binary
Specific Type: Not Used
1.3 Role Type
Always On Slave (AOS): ROLE_TYPE_SLAVE_ALWAYS_ON (0x05)
1.4 Command Class
Z-Wave Plus Info V2 none
Supervision V1 none
Association V3 highest granted
Association Group Information V3 highest granted
Manufacturer Specific V2 highest granted
Version V3 highest granted
Page 3
2
Device Reset Locally V1 highest granted
Power Level V1 highest granted
Indicator V3 highest granted
Firmware Update Meta Data V5 highest granted
Configuration V4 highest granted
Central Scene V3 highest granted
Switch Binary V2 highest granted
Scene Activation V1 highest granted
Scene Actuator Configuration V1 highest granted
2 Installation wiring diagram
2.1 Single pole wiring
Page 4
3
2.2 3-Way wiring
2.3 4-Way wiring
Page 5
4
Functions
Action Button
Description
2 Z-Wave™ Network Operation
Send NIF for network pairing/ inclusion (white LED quick
Inclusion 1x tap
Out of network
In network
Central Scene 2x tap In network
In network
Exclusion 3x tap
Out of network
Toggle parameter 86 4x tap
Toggle parameter 84 5x tap
Top button
Toggle parameter 85 6x tap
flashes). If pairing is successful, the LED will turn to solid
green for 2s, then deactivates.
Trigger to send Central Scene 1x tap scene.
Trigger to send Central Scene 2x tap scene.
Send NIF for network unpairing/ exclusion (purple LED
flashes).
Trigger to send Central Scene 3x tap scene.
Toggle parameter 86 from value 0 - 100%.
Toggle parameter 84 from value 0 - 9.
Toggle parameter 85 from value 0 - 9
Toggle parameter 83 7x tap
Toggle parameter 121 4x tap
Toggle parameter 122 5x tap
Toggle parameter 20 6x tap
Toggle parameter 120 10x tap
Central Scene Press and hold for 1 - 15s
Central Scene Release
Nothing Press and hold for 16 – 19s
Factory reset Press and hold for 20s
1) This device must be used in conjunction with a Security 2 Enabled Z-Wave Controller in order to fully utilize all
implemented functions.
Bottom button
Toggle Parameter 83 from values 0, 1, 2.
Toggle parameter 121 from value 0, 1, 2, 3.
Toggle parameter 122 from value 0, 1, 2.
Toggle parameter 20 from value 0, 1, 2
Toggle Parameter 120 from value 0, 1, 2
Trigger to send Central Scene hold scene.
Trigger to send Central Scene release scene.
Flash red LED rapidly.
Manual Factory reset -> Send gateway RESET DEVICE
LOCALLY
Note: When the LED turns into Blue, then release the button,
the LED will be solid Blue for 2 seconds, during the 2
seconds, tap the button again, it will start the factory reset
process, then return to factory reset LED status.
3 Association Groups
The device supports 5 association groups and every group supports max 5 associated nodes.
Group 1 is lifeline group, all nodes associated in this group will receive the messages sent by device through lifeline.
Group 2-5 are controlling groups.
The Command Class supported by each association group is shown in the table below:
Page 6
5
ID Name
Node Count
Profile
Function
1 Lifeline 5 General: Lifeline
Device Reset Locally Notification:
Basic Set or Switch Binary Set:
Basic Set or Switch Binary Set
Basic Set or Switch Binary Set
Basic Set or Switch Binary Set
command class
Indicator ID
Property ID
0x50 (NODE IDENTIFY)
0x03(ON OFF
PERIOD)
2 Top button
set ON/OFF
5 Control: Key 1
Issued when Factory Reset is performed.
Indicator Report:
Issued when included successfully.
Switch Binary Report:
Issued when output status is changed. (Determined by
Parameter 80).
Basic Report:
Issued when output status is changed (Determined by
Parameter 80).
Central Scene Notification:
Issued when button press or hold or release. (Determined by
Parameter 121).
Issued when Top button press. (The command class is
determined by Parameter 82)
3 Bottom
button set
ON/OFF
4 External
switch set
ON/OFF
5 Top and
bottom
button set
ON/OFF
5 Control: Key 2
5 Control: Key 3
5 Control: Key 4
4 Basic Command Map
Basic CC is mapped to Switch Binary Command Class.
Basic Set is mapped to Switch Binary Set.
Issued when Bottom button press. (The command class is
determined by Parameter 82)
Issued when External Switch press. (The command class is
determined by Parameter 82).
Issued when Top or Bottom button press. (The
is determined by Parameter 82).
5 Indicator Command Class
0x50 (NODE IDENTIFY) 0x04(ON OFF CYCLES)
0x50 (NODE IDENTIFY) 0x05(ONE TIME ON OFF PERIOD)
6 Manufacturer Information
Page 7
6
Parameter
Value
Parameter
Name
Information
Size MIN MAX Default
Description
20 Power
Status after power failure.
1 0 2 2 0- return to OFF
40 Auto Turn
Timer that auto turn off once
4 0 65535
0 0- disabled
41 Auto Turn
Timer that auto turn on once
4 0 65535
0 0- disabled
80 Instant
The command for status report.
1 0 2 2
Nothing
82 Association
Setting command for
1 1 2 1 1
- Basic Set
83 Led
Select the
indicator function for
1 0 2 2 0
- disable completely
84 Led
Select the indicator color for
1 0 9 9 0
- Disabled
85 Led
Select the indicator color for
1 0 9 2 0
- Disabled
Manufacturer ID 1 0x03
Manufacturer ID 2 0x71
Product Type ID 1 0x01
Product Type ID 2 0x03
Product ID 1 0x00
Product ID 2 0x26
7 Configuration
User can change the default settings by the below configuration parameters. After device reset, all these parameters
will be set to their default values.
Number
Restore
Off Timer
On Timer
Status
Report
Control
Settings
Indicator
Settings
Indicator
Color For
Output
turned on.
turned off.
association group.
output.
output.
1- return to ON
2- returns to last known state when
repowered
1- Auto turn off after 1s once turned on
65535 - Auto turn off after 65535s once
turned on
1- Auto turn on after 1s once turned off
65535 - Auto turn on after 65535s once
turned off
0-
1- Basic Report
2- Binary Switch Report
2- Binary Switch Set
1- Momentary blink
2- LED follows status of output
1- Red
2- Blue
3- Green
4- Pink
5- Cyan
6- Purple
7- Orange
8- Yellow
9- White
Indicator
Color For
Scene
scene.
1- Red
2- Blue
3- Green
4- Pink
5- Cyan
6- Purple
7- Orange
8- Yellow
Page 8
7
9
- White
86 Led
Setting the brightness of
1 0 100 60 0
- Disable
119 External
Enable or disable the scene
1 0 1 1 0
- Disable
120 External
Select the external(3
-
way)
1 0 2 0 0
- toggle on or off only
121 Output
Enable or disable output.
1 0 3 3 0- disable completely
122 Button
Select the paddle button
1 0 2 0 0
- up/ON, down/OFF
123 Report
Select behavior for report and
1 0 1 0 0
- report on/off status and change LED
Brightness
Switch
Scene
Switch Type
Control
Function
Behavior
indicator.
function of external(3-way)
switch.
switch's type.
functions.
indicator when output is
disable.
1- 1%
.. ...
100 - 100%
1- enable
1- NO momentary switch
2- NC momentary switch
1- enable local control
2- enable central scene
3- enable local and central scene
1- down/ON, up/OFF
2- toggle (up or down are the same)
indicator when parameter 121 is set
to 0 or 2
1- Don't report on/off status is pressed
and parameter 121 is set to 0 or 2
8 Security Network
This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to
communicate to other security enabled Z-Wave Plus products.
The device supports the security function with S2 encrypted communication. The device will auto switch to the
security mode when the device included with a security controller. In the security mode, the commands will use
security command class wrapped to communicate with others, otherwise the device will not response any commands.
This device supports security levels are listed in below table:
Security Levels
SECURITY_KEY_S0
SECURITY_KEY_S2_UNAUTHENTICATED
SECURITY_KEY_S2_AUTHENTICATED
Support (Yes/No)
No
Yes
Yes
9 SmartStart
SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the
product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be
added automatically within 10 minutes of being switched on in the network vicinity. You can find the QR code on the
bottom of the product, like this:
Page 9
8
And the DSK information will be shown like this:
DSK: XXXXX-XXXXX-XXXXX-XXXXX-XXXXX-XXXXX-XXXXX-XXXXX
10 Specifications
Power Supply AC120V, 60Hz
Max Amperage Max 15A
Max Wattage 1800W (US)
Max Standby Power 0.8W
LED RGB LED
Communication Frequency 908.40MHz, 916.00MHz (US)
Communication Range Up to 70m+ indoors (line of sight) or 150m outdoors.
Communication Certification Z-Wave Plus v2 with SmartStart
Operational Temperature
Operating Humidity 8% to 80%
0 - 40℃/ 32 - 104℉
Loading...