Aeotec ZWA019 User Manual

Water Sensor 7 Pro

ZWA019

Used in this guide.

Artículos utilizados en este manual / Utilisé dans ce guide / In dieser
Gebrauchsanweisung verwendete Bezeichnungen / Usato in questa guida /
Gebruikt in deze handleiding / Används i den här handboken.

PIN:12345

Main base

uint

QR Code used for SmartStart inclusion.

Note:

DSK Code can be found on packaging. Do not
remove or damage them.
Remarque: code QR utilisés pour l'inclusion
SmartStart. Le code DSK peut être trouvé sur
l'emballage. Ne les enlevez pas et ne les
endommagez pas.
Hinweis: Der QR-Code wird für die
SmartStart-Einbindung verwendet. Der
DSK-Code ist auf der Verpackung zu finden.
Entfernen oder beschädigen Sie diesen nicht.

Sensing head

Cabeza sensora / Tête de détection /
Sensorkopf / Testa sensibile / Hoofd
detecteren / Avkännande huvud

Probe

Main front
enclosure

Screws (x4)

Double-sided
Tape for Main
base unit (x2)

Double-sided

Tape for

Sensor Head (x2)

Important safety information.

Please read this and the online guide(s) at
support.aeotec.com/ws7p carefully. Failure to follow the
recommendations set forth by Aeotec Limited may be
dangerous or cause a violation of the law. The manufacturer,
importer, distributor, and / or reseller will not be held
responsible for any loss or damage resulting from not following
any instructions in this guide or in other materials.

To optimally detect water and leaks, Water Sensor 7 Pro is
intended for use in dry locations that then become wet.

Contains small parts; keep away from children.

Optimally placing Water Sensor 7.

The main unit of Water Sensor 7 Pro should be placed in a dry
location. It should be mounted vertically on a wall above the
place where you wish to monitor for potential floods or leaks. It
is the sensor probe of Water Sensor 7 Pro that detects liquids,
so the sensor probe must be placed in such a way that any
liquid or water of the leak will come into contact with it. When
placing Water Sensor 7 Pro probes do also consider in which
direction any flood or leak may flow and where one may occur.

Ensure that both of the probe contacts will be able to detect any
leak or flood. Only when the 2 probe contacts come into
contact with a liquid, Water Sensor 7 Pro will send a leak alert to
your Z-Wave gateway.

Quick start.

The following will step you through installing Water Sensor 7 Pro
and connecting it to your Z-WaveTM network.

1. Press and hold the Latch on the larger sensor part and
separate the front from the back-mount plate and then pull
the case off completely.

2. Remove the Pull Tab to engage the sensor’s pre-installed
batteries. The LED will flash red indicating that it is
powered on.

3. Add Water Sensor 7 Pro to your Z-Wave network;
a. If your Z-Wave gateway supports SmartStart: scan the

QR code on Water Sensor 7 Pro using the gateway’s
app. Your sensor will join your Z-Wave network
automatically.

b. If your gateway does not support SmartStart;

i. Set your Z-Wave gateway into its ‘add device’ mode.

Refer to the gateway’s manual if you are unsure of
how to perform this step.

ii. Press the sensor’s Tamper Switch 3 times within 1.5

seconds; it is located on the lower right side with the
battery pointed forward.

iii. Now Water Sensor 7 Pro is joining your Z-Wave

network or its LED will blink green and red and then
joins your network.

iv. If pairing is successful, it will change to a green color

for 3 seconds before turning off.
If pairing failed, LED will flash red 3 times, it was
unable to join your Z-Wave network; repeat the step
or contact us for further support if needed.

4. After testing Water Sensor 7 Pro in your chosen installation
location, affix the main sensor’s back-mount plate with
either the provided screws or double-sided tape.

Important. Make sure that the Water Sensor 7 Pro is
completely enclosed over the mounting plate, otherwise
the battery of your sensor will drain out within a few
days by remaining completely active.

Water Sensor 7 Pro is now a part of your Z-Wave home control
system. You can configure it and its automations via your
Z-Wave system; please refer to your software’s interface or
user guide for further information.

Get help & learn more.

Should you encounter any problem with Water Sensor 7 Pro
visit support.aeotec.com/ws7p or contact our support team via
aeotec.com/contact. You can also learn more about Water
Sensor 7 Pro’s features, configuration options, and technical
specifications at the link.

Gateway compatibility.

To see if this device is known to be compatible with your
Z-Wave gateway, please refer to aeotec.com/z-wave-gateways

Declaration of Conformity. Aeotec Limited declares that ZWA019 is in
compliance with the essential requirements and other relevant provisions of
RED 2014/53/EU, RoHS 2011/65/EU, IEC62321:2008 and EN50581:2012.
The full text of the declaration is available from
support.aeotec.com/ws7p/doc

© & ™ Aeotec Limited. Version: 501001900001 - AB

FCC ID: 2AOGIZWA019

In Europe contact Aeotec Group GmbH; Große Johannisstraße 7, 20457
Hamburg, Germany.

[e-mail]

www.aeotec.com

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.