Aemc instruments MF 3000-24-1-1, MF 3000-14-1-1 User Manual
FLEXIBLE
AC CURRENT SENSOR
MiniFlex
®
3000-14-1-1
3000-24-1-1
ENG
LISH User Manual
Statement of Compli an ce
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments
Chauvin Arnoux®, Inc.
www.aemc.com
certifies that this instrument has been calibrated
using standards and instruments traceable to
international standards.
We guarantee that at the time of shipping your
instrument has met its published specifications.
An NIST traceable certificate may be requested
at the time of purchase, or obtained by
returning the instrument to our repair and
calibration facility, for a nominal charge.
The recommended calibration interval for this
instrument is 12 months and begins on the date of
receipt by the customer. For recalibration, please
use our calibration services. Refer to our repair and
calibration section at www.aemc.com.
Serial #: ___________________________
Catalog #: 2132.60/2132.63
Model #: 3000-14-1-1 / 3000-24-1-1
Please fill in the appropriate date as indicated:
Date Received: ___________________________
Date Calibration Due:
__________________
d.b.a. AEMC® Instruments
Table of Contents
1. INTRODUCTION ........................................................................ 2
1.1 International Electrical Symbols ............................................... 3
1.2 Definition of Measurement Categories ..................................... 3
1.3 Receiving Your Shipment ......................................................... 4
1.4 Ordering Information ................................................................ 4
2. PRODUCT FEATURES ....................................................................... 5
2.1 Description................................................................................ 5
2.2 Features ................................................................................... 6
2.3 Control Features ....................................................................... 7
3. SPECIFICATIONS ........................................................................... 8
3.1 Typical Frequency Response Graphs...................................... 10
3.1.1 Amplitude Error .......................................................... 10
3.1.2 Phase Error ................................................................ 10
3.1.3 Frequency Limitation Versus Amplitude ....................... 11
4. OPERATION .................................................................................... 12
4.1 Compatibility ........................................................................... 12
4.2 Tips for Making Precise Measurements .................................. 12
4.3 Making Measurements
........................................................... 13
5. MAINTENANCE ...................................................................... 14
5.1 Maintenance ........................................................................... 14
5.1.1 Battery Replacement .................................................. 14
5.1.2 Cleaning ..................................................................... 14
Repair and Calibration .................................................................... 15
Technical and Sales Assistance ...................................................... 15
Limited Warranty ................................................................................. 16
Warranty Repairs ............................................................................ 16
2
MiniFlex® Flexible AC Current Probe
CHAPTER 1
INTRODUCTION
WARNING
T
hese safety warnings are provided to ensure the safety of personnel
and proper operation of the instrument.
Read this instruction manual completely and follow all the safety
information before attempting to use or service this instrument.
®
Safety is the responsibility of the operator. The MiniFlex
used only by qualified personnel using applicable safety
precautions.
Wear protective clothing and gloves as required.
Use caution on any circuit: potentially high voltages and currents
may be present and may pose a shock hazard.
must be
Read the safety specifications section prior to using the current
probe. Never exceed the maximum voltage ratings given.
ALWAYS de-energize the circuit before wrapping the MiniFlex
ound bare conductors, bus bars, or near live parts. Do not wr
ar
on
live conductors.
ALWAYS connect the electronic module to the display devic
bef
ore wrapping the MiniFlex
ALWAYS inspect the module, sensor, sensor cable, and output
terminals prior to use. Replace any defective parts immediately.
Use only factory parts.
NEVER use the MiniFlex
1000V CAT III; 600V CAT IV.
®
ap
®
around the sample being tested.
®
on electrical conductors rated above
e
3
MiniFlex® Flexible AC Current Probe
1.1 International Electrical Symbols
manual, the symbol preceding instructions indicates that if the instructions are not
European Union, this product is subject to a separate collection system for
recycling electrical and electronic components In accordance with directive WEEE
2002/96/EC
This symbol signifies that the instrument is protected by double or reinforced
insulation.
This symbol on the instrument indicates a WARNING and that the operator must
refer to the user manual for instructions before operating the instrument. In this
followed, bodily injury, installation/sample and product damage may result.
Risk of electric shock. The voltage at the parts marked with this symbol may be
dangerous.
This symbol refers to a type B current sensor. Do not apply around or remove
from HAZARDOUS LIVE conductors without additional protective means (deenergizing the circuit or wearing protective clothing suitable for high voltage
work).
Battery
Compliance with the Low Voltage & Electromagnetic Compatibility European
directives (73/23/CEE & 89/336/CEE)
In the
1.2 Definition of Measurement Categories
CAT II: For measurements performed on circuits directly connected to the
electrical distribution system. Examples are measurements on household
appliances or portable tools.
CAT III: For measurements performed in the building installation at the
distribution level such as on hardwired equipment in fixed instal lation and
circuit breakers.
CAT IV: For measurements performed at the primary electrical supply
(<1000V) such as on primary overcurrent protection devices, ripple
control units, or meters.
4
MiniFlex® Flexible AC Current Probe
1.3 Receiving Your Shipment
Upon receiving your shipment, make sure that the contents are consistent
with the packing list. Notify your distributor of any missing items. If the
equipment appears to be damaged, file a claim immediately with the carrier and notify your distributor at once, giving a detailed description of any
damage. Save the damaged packing container to substantiate your claim.
1.4 Ordering Information
MiniFlex® Model 3000-14-1-1 .................................................. Cat. #2132.60
®
MiniFlex
Model 3000-24-1-1 .................................................. Cat. #2132.63
Order Accessories and Replacement Parts Directly Online
Check our Storefront at
www.aemc.com/store
for availability
Loading...