Chauvin Arnoux
Phone: (800) 343-1391 • (603) 749-6434 • Fax: (603) 742-2346 • www.aemc.com
®
, Inc. d/b/a AEMC® Instruments • 15 Faraday Dr. • Dover, NH 03820
AEMC® INSTRUMENTS AC CURRENT PROBE MN352 / MN353 Cat.# 2116.26/ 2116.27
GENERAL DESCRIPTION
The MN probe is the latest in compact AC Current
probes. Designed to meet the most stringent demands
in industry and electrical contracting, they also meet the
latest safety and performance standards.
ELECTRICAL SPECIFICATIONS
Operating Range: 150A
Measurement Range: 0.1 to 150A
Transformation Ratio: Voltage output
Output Signal: 10mV/A (1V at 100AAC)
Range Accuracy
0.1 to 1A ≤ 3% of Reading ± 0.2mV
1 to 20A ≤ 2% of Reading ± 0.2mV
20 to 80A ≤ 1% of Reading
80 to 150A ≤ 3% of Reading
150 to 200A ≤ 7% of Reading
Range Phase Shift
0.1 to 1A N/A
1 to 20A
20 to 80A
80 to 150A
150 to 200A
≤3°
≤2°
≤3°
≤4°
Overload: 240A for 10 min ON, 30 min OFF
*Reference conditions: 18°C to 28°C, 20 to 75% RH, external magnetic field <40
A/m, 48 to 65 Hz sine wave, distortion factor less than 1%, no DC component, no
external current carrying conductor, test sample center ed. Load impedance> 1M
Frequency Range: 40 to 10kHz
Limit Operating Conditions: 200A permanently to 1kHz;
Derating above 3 kHz: 200 A x (1/0.333F), F in kHz
Crest Factor: 3 @ 150Arms with an error (due to CF) of 3%
Working Voltage: 600Vrms
Common Mode Voltage: 600Vrms
Influence of Adjacent Conductor: <15mA/A at 50Hz
Influence of DC on AC signal: DC current <20A, < 5%
Influence of Conductor Position in Jaw:
0.5% of mV output @ 50/60Hz
Influence of Frequency:
40 Hz to 1 kHz: 3% of mV output
1 kHz to 10 kHz: 12% of mV output
Influence of Load:
< 3% of mA output from 40 Hz to 1 kHz
< 12% of mA output from 1 kHz to 10 kHz
MECHANICAL SPECIFICATIONS
Dimensions: 5.47 x 2.00 x 1.18" (139 x 51 x 30 mm)
Weight: 180 g (6.5 oz)
Ω
.
Jaw Opening: 0.83” (21mm)
Maximum Conductor Size:
Cable: 0.78” (20mm)
Bus Bar: 0.78 x 0.19 (20 x 5mm)
Case Protection: IP 40 (IEC 529)
Drop Test: 1.0 m (IEC 68-2-32)
Mechanical Shock: IEC 68-2-27
Vibration: IEC 68-2-6
Polycarbonate Material:
Jaws: Polycarbonate with 10% fiberglass charge, Red UL 94 V0
Case: Polycarbonate 920A Gray
Opening Operations - Life: > 50,000
Output:
MN352: Two standard safety banana jacks (4 mm)
MN353: Double/reinforced insulated 5 ft (1.5 m) lead with 4mm
safety banana plug
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature: 14° to 131°F (-10° to +55°C)
Storage Temperature: -40° to 158°F (-40° to +70°C)
Altitude: Non-operating: 0 to 12,000 m
Operating: 0 to 2000 m
Operating Relative Humidity:
10-35°C 85% RH (without roll-off above 35°C)
Influence of Temperature:
≤ 150 ppm/°K, or 0.15% of mV output per 10°K
Influence of Humidity (10 to 90% RH):
≤ 0.2% of mV output per 10°K @ 18°C to 28°C
SAFETY SPECIFICATIONS
Electrical:
Double insulation or reinforced insulation between
the primary or secondary and the outer case of the
handle conforms to IEC 1010-2-32.
600V Cat. III, Pollution Degree 2
Dielectric Strength:
5550 V, 50/60 Hz between primary, secondary
and the outer case of the handle
Electromagnetic Compatibility:
EN 50081-1 Class B
EN 50082-2 Electrostatic discharge; IEC 1000-4-2
Radiated field IEC 1000-4-3
Fast transients IEC 1000-4-4
Magnetic field at 50/60 Hz IEC 1000-4-8
ORDERING INFORMATION
AC Current Probe MN352.................................. Cat #2116.26
AC Current Probe MN353.................................. Cat #2116.27
Accessories:
MN352 - Leads, set of 2, 5 ft safety (1000V)........ Cat #2111.29
Banana plug adapter (to non-recessed plug) ...... Cat #1017.45
Rev 01 01/09 Page 1 of 1
Loading...