Page 1
Upright
Index
VACUUM CLEANER
Household Type
OWNER’S GUIDE
Z2900 SERIES
IMPORTANT
For any advice
on your cleaner and to
order dustbags, fi lters
and accessories,
please telephone
Electrolux
Customer Care
Important Information 2-3
Guarantee ..................... 3
Assembly Parts ............. 4
How to Assemble .......4-5
How to Use ................... 5
Accessories .................. 6
Filters ............................ 6
Dustbag .....................6-7
Smartbox ...................... 7
Brush Roll & Belt ..........8
How to Clear
Blockages ..................... 9
Troubleshooting ..........10
Thermal Cut Off .......... 10
08706 055055
Please Retain
We suggest you record the model, type and serial numbers
below. They are located on the silver rating plate on your
cleaner. For prompt and complete service information, always
refer to these numbers when inquiring about service.
Model & Type___________________________
Serial No. ______________________
It is also important to keep your receipt as proof of date of
purchase.
www.electrolux.co.uk
Page 2
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fi re, electric shock, or injury:
Do not use outdoors or on wet surfaces.
•
Do not leave vacuum cleaner when plugged in. Turn off
•
the switch and unplug the electrical cord when not in use
and before servicing.
Do not allow to be used as a toy. Close attention is
•
necessary when used by or near children.
Use only as described in this manual. Use only manufacturer’s
•
recommended attachments.
Do not use with damaged cord or plug. If vacuum cleaner
•
is not working as it should, has been dropped, damaged,
left outdoors, or dropped into water, return it to a service
center before using.
Do not pull or carry by cord, use cord as a handle, close
•
door on cord, or pull cord around sharp edges or corners.
Do not run vacuum cleaner over cord. Keep cord away from
heated surfaces.
Do not use extension cords or outlets with inadequate
•
current carrying capacity.
Turn off all controls before unplugging.
•
Do not unplug by pulling on cord. To unplug, grasp the plug,
•
not the cord.
Do not handle plug or vacuum cleaner with wet hands.
•
Do not put any object into openings. Do not use with any
•
opening blocked; keep free of dust, lint, hair, and anything
that may reduce airfl ow.
This vacuum cleaner creates suction and contains a
•
revolving brush roll. Keep hair, loose clothing, fi ngers, and
all parts of body away from openings and moving parts.
• Do not place cleaner on furniture or stairs as the brush roll
may cause damage. Place cleaner on fl oor with the handle
in storage position while using attachments.
Do not pick up anything that is burning or smoking, such
•
as cigarettes, matches, or hot ashes.
Do not use without dust bag in place.
•
Belt pulleys can become hot during normal use. To prevent
•
burns, avoid touching the belt pulley when servicing the
drive belt.
Use extra care when cleaning on stairs.
•
Do not use to pick up fl ammable or combustible liquids such
•
as gasoline, or use in areas where they may be present.
Store your cleaner indoors in a cool, dry area.
•
Keep your work area well lighted.
•
Unplug electrical appliances before vacuuming them.
•
SAVE THESE INSTRUCTIONS
BEFORE YOU START
CHECK THE VOLTAGE
First check the voltage shown on the data plate (see rear view)
to make sure that the cleaner is of the correct voltage for your
electricity supply. If it is not, do not use the cleaner but refer back
to your dealer.
CONNECTING TO YOUR ELECTRICITY SUPPLY
Permanently connected to the cleaner is a mains supply (2-core)
cable fi tted with a non-rewirable plug incorporating a 13A fuse.
In the event of the fuse requiring replacement the fuse cover should
be removed using a small screwdriver. The old fuse MUST be replaced
by a 13A ASTA approved BS1362 fuse or a BSI approved fuse. The
cover must be replaced before the plug is used again. In the event
of loss of the fuse cover, replacements can be obtained from your
Electrolux Retailers and must be of the same colour as indicated by
the coloured insert on the base of the plug.
If diffi culty is experienced in obtaining a replacement, contact Electrolux
on 08706 055055.
In no circumstances must the plug be used without a correct
fuse cover fi tted.
If the plug that is fi tted to your appliance is not suitable for your socket
outlet, it must be cut off and the appropriate plug fi tted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the hazard of
shocks in case it should be plugged into a 13 amp socket in another
part of your home.
The wires in the mains cable of this appliance are coloured in
accordance with the following code: Blue: Neutral. Brown:
Live.
As the colours of the wires in the mains cable of this appliance may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
If using a three-pin plug, do not make any connection to the terminal
marked with the letter E or by the earth symbol or coloured green
or green-and-yellow. This cleaner is double insulated and no earth
connection is necessary.
It is in your interest to ensure that the plug is correctly attached
to the mains cable. In case of doubt, have it done by a qualifi ed
electrician, as Electrolux cannot regard the repair of faults on the
plug connection as a service that can be given free of charge under
the terms of the guarantee.
Fuse Cover
Fuse
Blue
13 Amp Fuse
Brown
Cord Clamp
2
Page 3
BEFORE YOU START (continued)
WARNING
The brush in the cleaning head rotates at high speed and can
cause damage to the mains supply cable if the cleaner passes
over it during cleaning operations.
Care should be taken to ensure that this does not happen. If the
cleaning head has accidentally passed over the mains supply cable
the following action should be taken:
1. Switch off and remove the plug from the socket outlet.
2. Examine the mains supply cable for damage (only after removing
the plug from the socket outlet).
3. If there is any sign of damage to the supply cable it MUST be
renewed. The repair MUST be carried out by an Electrolux Service
Agent or a similar qualifi ed person.
4. NEVER use the machine with a damaged mains supply cable.
Proprietary carpet conditioning and air freshening materials
After using proprietary carpet conditioning powders, it is recommended
that the dustbag or fi lters be changed. Some of these preparations
contain substances which if left in the vacuum cleaner for extended
periods could damage the plastic mouldings which form the structure
of the cleaner.
Many air fresheners, household deodorants, sprays and polishes
contain a highly fl ammable gas propellant.
Because of this, it is particularly important that these products are used
strictly in accordance with the relevant manufacturer’s instructions.
It is essential that none of the above products are sprayed directly
into the vacuum cleaner or any of its fi lters, hose assembly, dustbag
chamber or dust cup.
SERVICE
Should you require service on your Electrolux cleaner, please
telephone Electrolux on 08706 055055. Before requesting service,
please check whether your problem is covered under the Service
Checklist (see below).
New fi lter pads, dustbags, brush rollers and drive belts can be
obtained from Electrolux Retailers. If diffi culty is experienced in
obtaining spares, please contact Electrolux on 08706 055055.
SERVICE CHECKLIST
• If your cleaner will not operate, check the plug connection, plug
fuse and mains fuse.
• Never allow the dustbag/Smartbox to become so full that it
impedes the air-fl ow, thus reducing the cleaning effi ciency of the
machine. The character of household dust and its effect on the
air-fl ow through the machine may vary considerably. Fluffy dust
allows air to pass through readily whereas fi ne powdery dust or
proprietary cleaning powders, pack tightly in the dustbag, offering
greater resistance to air-fl ow and will reduce cleaning effi ciency
if the bag becomes overloaded. Always ensure that you have a
spare genuine Electrolux dustbag.
• Always store your cleaner and spare dustbags/fi lters in a dry
place.
• Renew the fi lter pads three or four times a year. This is essential
to ensure continued high fi ltration of dust particles.
• Sucking up such items as stockings, clippings of cloth, sizeable
pieces of paper, wrappings from cigarette packets or sweets etc.,
may block the hose. Electrolux regrets that the clearing of
blocked hoses cannot be regarded as service that can be
given free of charge, under the guarantee. Should a blockage
occur, fi rst disconnect the cleaner from the electricity supply,
to section headed “Blockages”. If these operations are not
successful, contact us on 08706 055055.
• Never pick up hot cinders or lighted cigarette ends.
• Make certain that your cleaner does not come into contact
with water or any other liquid. It is not designed as a wet
pick up cleaner, and must never be used on damp carpets
or wet fl oors.
Important - in the event of the mains supply cable of this vacuum
cleaner requiring replacement, we recommend that this be carried
out by Electrolux Service Staff.
Spares
New fi lters, dustbags, brush rollers and drive belts can be obtained
from Authorised Electrolux Dealers and electrical retailers. If diffi culty is
experienced in obtaining spares please call us on 08706 055055.
Guarantee
This guarantee is in addition to your statutory and other
legal rights.
This product is for househould use only.
Electrolux products are carefully designed, manufactured, tested
and inspected and, in consequence, we undertake to replace or
repair any part found to be defective in material or workmanship,
within one year of delivery to the original purchaser, free of charge.
You may be required to take the product to your nearest service
provider if the product requires attention during the fi rst year.
There are certain conditions which may invalidate this
guarantee:
a. It is dependent upon the appliance being correctly installed
and used in accordance with the Company’s instructions
under normal domestic conditions within the United Kingdom
or the Republic of Ireland.
b. Service at all times must be carried out by an Electrolux
Service Representative or authorised agent.
c. The guarantee may be invalidated by unauthorised repair or
modifi cation of the appliance.
d. You may be charged by Electrolux if you call for an engineer to
resolve a problem that we believe is covered in the instruction
booklet. (example: blocked/dirty fi lters)
The Company does not accept liability for defects arising from
neglect, misuse or accident. This guarantee excludes such normal
wearing parts as drive belts, brushes, fi lters and dustbags as the
life of these depends upon the amount and nature of use.
Proof of the date of purchase will be required before service
under guarantee is provided. Please call 08706 055055 for
assistance.
Important:
For future reference we suggest you record the following details
here, and keep the receipt with this handbook as proof of
purchase.
Purchased from ____________________________________
Date purchased _________________ Model no ___________
3
Page 4
Assembly Parts
4
3
2
Nested extension tubes and Crevice Nozzle (Pull
1
apart.)
Dusting Brush.
2
Hose.
3
Vacuum Cleaner Body.
4
Electrical Cord.
5
5
Handle.
6
Screws located in the accessory package.
7
1
6
How To Assemble
CAUTION: Assemble the cleaner before using.
CAUTION: Moving parts, make sure ON/OFF switch is in
the OFF position before plugging in.
Grasp dustbag/Smartbox
1
cover handle and pull
away from vacuum body
to remove door.
Slide the handle into the
2
grooves at the top of the
vacuum body as shown.
Place the two screws
3
(supplied) into the holes
at the top of the dustbag/
Smartbox compartment
and tighten with a
screwdriver.
Place the tabs on the
4
bottom of the dustbag/
Smartbox cover into slots
at the bottom of the bag
compartment and rotate
door up and push against
the vacuum body until it
snaps shut.
Place the hose on the back
5
of the vacuum, wrapping it
up and over the hose hook
as shown.
Firmly push the end of
6
the hose into the hose
retainer in the hood of the
vacuum.
4
Page 5
How To Assemble (continued)
Pull the electrical cord up
7
to the cord retainer and
firmly push down into
retainer. This will keep the
cord out of the way the
next time you vacuum.
Wind the cord around the
8
two cord hooks on the
back of the vacuum.
Secure plug to the cord to
9
prevent unwinding.
How To Use
WARNING: Avoid injury. Keep loose clothing, hair,
fingers, and all other parts of body
away from any moving part (such as the
revolving brush). Turn off the switch and
unplug the cleaner before changing the
fl oor type selector.
ON/OFF Switch.
International symbol I
means On, International
symbol O means Off.
Handle Release. Step
on handle release to pull
handle back to a comfortable
operating position. To lower
handle completely to the fl oor,
depress handle release a
second time.
Store the extension tubes
10
on the side of the vacuum
in front of the hose.
Store the dusting brush.
11
Helpful Information:
Before cleaning under low
furniture, check area fi rst for
objects that might harm the
cleaner or block the vacuum
hose.
Floor Type Selector. An adjustment that raises or lowers
the cleaner base to match the type of fl oor surface. With the
cleaner cord unplugged, set the adjustment to lowest setting for
maximum carpet cleaning. If the cleaner is diffi cult to push,
move adjustment to next highest setting until cleaner is
comfortable to push. The brush roll must reach the carpet
for effective cleaning. For ease in moving the adjustment knob,
place handle in operating position and tilt cleaner back to
remove weight from front wheels.
Helpful Information:
Listen to your cleaner. If you notice a change in the
sound of the motor or a change in performance, it could
simply indicate a common usage or maintenance issue.
Such as, a need to raise or lower the carpet height
adjustment, possible blockage in hose or brush roll
area, or a broken or loose brush roll belt. These are
all easy to fi x and the instructions are included in this
handbook. Becoming familiar with the information in this
guide will help you to get the best possible performance
from your new cleaner for many years to come.
5
Page 6
How To Use (continued)
NOTE: While using accessories, do not place cleaner
on furniture or steps as the brush roll may
cause damage. Place cleaner on fl oor with the
handle in storage position.
1. To use accessories remove hose from hose retainer in hood
of cleaner by lifting up and twisting.
2. Place desired accessory onto end of hose or extension
tubes.
Crevice
Nozzle
Dusting/
Upholstery
Brush
Routine Maintenance
NOTE: Turn off the switch and unplug the electrical cord
before routine maintenance. Never operate the
vacuum cleaner without the dustbag/Smartbox or
fi lter assembly in place.
NOTE: When vacuuming using carpet fresheners or
cleaners, powder, plaster dust, or similar fine
substances, the dustbag/Smartbox and fi lters will
require more frequent maintenance.
Models Z2901 Z2905 Z2910
Removing the Dustbag E82:
Dusting/Upholstery Brush is for furniture, blinds,
books, lamp shades, shelves, curtains, draperies, cushions
and fabrics.
Crevice Nozzle cleans corners, stairs, skirting boards, and
between cushions.
Nested extension tubes to add reach.
• Grasp both tubes near ridges.
• Pull apart.
• Turn ridge end to center.
• Push tubes together.
Remove dustbag cover.
Check the fi lters each time the dustbag or Smartbox
is changed. Clean or replace as needed.
Shake fi lter to remove excess dust. If necessary, the
filters can be cleaned by vacuuming with another
cleaner.
Grasp dustbag flaps and pull
dustbag from cleaner.
The instructions in this booklet serve as a guide to routine
maintenance. To avoid unnecessary service calls, check the
dustbag, fi lters, belt, and brush roll often.
6
Micro fi lter ref: EF2
HEPA fi lter ref: EF82
Page 7
Rountine Maintenance (continued)
Installing New Dustbag Ref: E82
Fold dustbag fl aps of new bag
back and slide into unit. Make
sure inlet goes into opening on
dustbag.
Replace dustbag cover
on unit.
NOTE: Dustbag cover
cannot be closed
unless the dustbag is
installed properly.
Models Z2915 Z2920 Z2925
Emptying and Cleaning the Smartbox
NOTE: Switch cleaner off at the mains and remove plug
from the electricity supply before emptying or
cleaning the Smartbox.
Emptying the Smartbox:
It is important to empty the smartbox regularly. DO NOT allow
the Smartbox to become too full.
Pull the Smartbox out of the cleaner.
Pull the Smartbox apart and empty the dust and debris into a
dustbin. Brush out the smartbox to remove the excess.
Washing the Smartbox:
The Smartbox can be washed in warm water. A small amount
of washing up liquid may be added. A brush may be used
to remove stubborn dust. Rinse the Smartbox thoroughly
and remove the excess water with a dry cloth. Dry the dust
container thoroughly (24 hours is preferred) before refi tting to
the cleaner.
Remove dustbag/Smartbox cover.
7
Page 8
Periodic Maintenance
NOTE: Turn off the switch and unplug the electrical cord
before periodic maintenance. Never operate the
vacuum cleaner without the dustbag/Smartbox
or fi lter assembly in place.
Brush Roll
The brush roll turns as it sweeps and combs the carpet pile.
Remove hair and threads from the brush roll so it continues
brushing the carpet. To maintain the most effi cient cleaning,
the bristles must touch the carpet.
Brush Roll Belt
The brush roll belt turns the brush roll to agitate, sweep, and
comb the carpet pile. Check the belt regularly to be sure it is in
good condition. Replace the belt if it stretches, cracks or loses
tension. Cut away any hair or threads wound around the brush
roll or the belt pulley because the buildup could cause the belt
to rotate unevenly.
How To Replace Brush Roll Belt
4. Lift left end of brush roll.
5. Remove and discard belt.
6. Place new belt around motor shaft.
7. Place new belt around brush roll pulley.
1. Lower handle to fl oor to change belt.
2. Remove the two screws from the top of the hood.
8. Align left end cap with base. Push end cap securely into
place.
9. Pull right side of brush roll to stretch belt. Secure right end
cap into base.
IMPORTANT
10. Rotate brush roll by hand two full rotations to properly
position belt.
11. Place hood back on cleaner. Replace and tighten two
screws.
12. Return vacuum to upright position.
3. Lift hood to remove.
8
Page 9
To Clear Blockages in Hose
NOTE: Turn off the switch and unplug the electrical cord
before clearing hose.
3. Remove the hood from the cleaner and check for a blockage
in the brush roll area. Make sure the hose inlet is clear. If
no blockage is found, continue to step 4.
After the blockage is found and cleared, replace the hood
on the cleaner.
Hose
Retainer
Hose
1. Firmly pull the end of the hose from the hose retainer on
the hood of the vacuum.
2. Check for blockages in the hose and hose retainer. Flexing
the hose may help loosen any blockage. If no blockage is
found, continue to step 4.
If blockage is found, clear the blockage and replace the
hose in the hose retainer. If the blockage is in the hose
retainer and cannot be cleared, continue to step 3.
4. Twist the hose from the coupling elbow on the back of
cleaner. Check for blockages at cleaner opening and in
hose. If a blockage is found, clear the blockage.
The two screws attaching the clear hose adapter can be
removed for better access to a blockage.
5. Screw the hose back onto the back of the cleaner and
replace the other end of the hose into the hose retainer on
the hood of vacuum.
9
Page 10
NOTE: Turn off the switch and unplug the electrical cord before servicing.
Motor will not start. Electric Plug Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
Motor suddenly stops. Thermal Cut Off See below.
Does not clean the carpet Filters Clean or replace the fi lters. Hint: If picking up fi ne
or fl oor. dust, the fi lters may not look dirty but a fi ne substance
tends to reduce suction when it blocks the airfl ow
through the fi lter(s). Page 5.
Dustbag Replace the dustbag with a new dustbag. Page 6.
Be sure the dustbag or Smartbox is properly seated
into the cleaner body. Page 6.
Hose Be sure hose adapter is secure on back of cleaner.
Page 9.
Remove any blockages from the hose that restrict the
airfl ow. Page 9.
Check to see that the end of the hose is fi rmly pressed
into the hose retainer in the hood of the vacuum.
Check base hose and long hose. Page 8.
Belt Replace a broken, cut, loose or out of shape belt.
Brush Roll Clean hair and thread from bristles and end cap area.
Replace brush roll if bristles are worn.
No suction at the end of hose. Hose Adapter Be sure hose adapter is secure. Page 9.
Filters Clean or replace the fi lters. Hint: If picking up fi ne
dust, the fi lters may not look dirty, but a fi ne substance
tends to reduce suction when it blocks the airfl ow
through the fi lters.
Hose Remove any clogs from the hose that restrict the
airfl ow. Check base hose and long hose. Page 9.
Dustbag Change dustbag.
PROBLEM CAUSE SOLUTION
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Noise from the brush roll Brush Roll Remove hood and clean debris or items from the brush
area. roll area.
Belt Replace a broken, cut, loose or out of shape belt.
Page 7.
Cleaner is hard to push. Floor Type Selector Put handle in operating position. Tilt the cleaner
back to raise the front wheels off fl oor. Then turn the
knob to a higher setting.
Belt Replace a broken, cut, loose or out of shape belt.
Page 7.
Cleaner height knob will Floor Type Selector Hint: Put handle in operating position. Tilt the
not turn. cleaner back to raise the front wheels off fl oor.
Then turn the knob.
Missing parts Call 08706 055055. Know the model and serial
numbers when you call.
Questions? Call 08706 055055. Know the model and serial
numbers when you call.
✓
✓
✓
✓
✓
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly
shuts off, push the on/off switch off (0) and unplug the cleaner. Check the cleaner for a possible source of overheating such as
a full dustbag, a blocked hose or clogged fi lter. If these conditions are found, fi x them and wait at least 30 minutes before attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and push the on/off switch on (l). If the cleaner
still does not run, please call Electrolux Customer Care on 08706 055055.
10
Page 11
The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city offi ce, your household waste disposal service or the shop
where you purchased the product.
11
Page 12
Questions?
Call
08706 055055
Thank you for purchasing an
Electrolux cleaner.
Don’t Forget to Use
Genuine Electrolux
Bags and Belts
CAUTION: Damages caused by the use of non-
genuine Electrolux bags are not covered
by the Electrolux Limited Warranty.
101 Oakley Road, LUTON, BEDFORDSHIRE, LU4 9QQ
Features of the Electrolux vacuum cleaner and accessories supplied with it are protected in Great Britain and abroad by Patents or
Registered Designs.
This appliance conforms with the requirements of the amended E.E.C. directive No. 89/336/EEC relating to electromagnetic compatibility
(EMC) CE.
Electrolux may introduce modifi cations to their products from time to time, and consequently the details given in this booklet are subject
to alteration without notice.
Part No. 73412A_Rev1 (11/05)
©2005 Electrolux Home Care Products Ltd..
Printed in China
Loading...