AEG-Electrolux WASL3MW, TKSL3MW User Manual

INSTALL ATION AND

MAINTENANCE

WA SL3 M

TK SL3 M TA SL3 M

WASHING MACHINE 2-15

TUMBLE DRYER 16-34

INDEX 36

CONTENTS – WASHING MACHINE

SAFETY 3

Transit screws

General

Child lock on Start/Stop button

Door

Overfill cut-out

Packaging

Transport/Winter storage

Scrapping

PARTS OF THE WASHING MACHINE 4

TECHNICAL INFORMATION 4–5

Technical data

Programme cycles

MECHANICAL INSTALLATION 6–8

Transit screws

Positioning the washing machine

Adjusting the feet

Connecting to water supply

Water intake – mixed or cold water

Connecting to drain

CHANGING SETTINGS 10–11

Language

Locking the programme

Wash temperature, C or F

Changing preset wash temperature

Child lock

MAINTENANCE 12–13

Emptying/cleaning trap and drain pump

Inspection holes under drum paddles

Cleaning the detergent drawer

Cleaning the outside of the machine

In areas with hard water

TROUBLESHOOTING 14–15

Door will not open

Machine will not start

Error messages

The display is lighting when a program

me is selected, but no characters or

digits are shown

Wrong language displayed

ELECTRICAL INSTALLATION 9

Electrical installation

Connecting to coin mechanism

WASHING MACHINE CONTENTS

SAFETY

GENERAL

• Read and keep this manual!

• Any electrical work or plumbing must be car-

ried out by qualified tradesmen.

• Remove the transit screws before you use the

machine, see Mechanical installation.

CHILD LOCK ON BUTTON

To prevent accidental button pushes on the

button you can activate the child lock

function. The

button then must be held

in for three seconds to activate the machine.

DOOR

The door is opened electrically, so it cannot be

opened until the machine is connected to the

electrical supply! The door can however be ope-

ned in an emergency, see Troubleshooting.

OVERFILL CUT-OUT

If the water level in the machine rises above

normal the overfill cut-out shuts off the water

intake and starts pumping out the water. The

programme resumes when the water level has

dropped.

TRANSPORT/WINTER STORAGE

If you intend to transport the machine or store

it over winter in unheated premises, empty the

trap and the drain pump, see the chapter on

Maintenance.

Any questions? Call service.

SCRAPPING

At the end of its life the machine must be disa-

bled before being scrapped.

Contact your local recycling centre to find

out where to dispose of it or recycle it.

The machine has been built and marked to

facilitate recycling.

PACKAGING

Recycle the packaging according to recommen-

dations in your area.

SAFETY WASHING MACHINE

PARTS OF THE WASHING MACHINE

1. DETERGENT DRAWER

2. POWER SWITCH

3. PROGRAMME PANEL

4. RATING PLATE

5. DOOR-DRAIN PUMP/EMERGENCY OPEN

6. DRAIN PUMP/EMERGENCY OPEN (BEHIND

FLAP)

7. DOOR

1. DETERGENT COMPARTMENT – PRE-WASH

2. DETERGENT COMPARTMENT – MAIN WASH

3. FABRIC CONDITIONER COMPARTMENT

1 2 3

5 6

TECHNICAL INFORMATION

TECHNICAL DATA

Height, Width, Depth: 850 mm, 595 mm, 585 mm. Weight: 73 kg.

Drum capacity: 50 l. Max wash load: 6.0 kg. Spin speed: 1200 rpm. Power rating and element power: See rating plate. Water pressure: 0.1–1 MPa, 1–10 kp/cm2, 10–100 N/cm2. Composition of drum and fluid container: Stainless steel. Composition of casing: Powder-painted and hot-dip galvanized sheet steel or stainless steel. Installation: Static on four adjustable, rubber-covered feet. Water supply: 1.5 m PEX hose. Drain: 1.7 m polypropylene hose (pump) or 0.4 mm EPDM

This machine is approved for all UK applications as suitable for Category 5. Product is listed in the WRAS regulations advisory scheme directory and is suitable for direct connection to mains drinking water. No special plumbing arangements e.g. break tanks are required.

WASHING MACHINE PARTS OF THE WASHING MACHINE/ TECHNICAL INFORMATION

rubber hose (valve).

EURO

PROGRAMMES

Main wash

Pre wash

Max .load

P1 Heavy wash 90°C

P2 Normal wash 60°C

P3 Light wash 60°C

P4 Normal wash 40°C

P5 Synthetic wash 40°C

P6 Super quick wash 40°C

P7 Wool/hand wash 30°C (1)

P8 Spin

(1) High water level and gentle motor action.

MEDICAL PROGRAMMES

Main wash

Pre wash

Max .load

P1 Heavy wash 90°C (2)

P2 Heavy wash 80°C (2)

P3 Normal wash 60°C

P4 Normal wash 40°C

P5 Synthetic wash 40°C

P6 Super Quick wash 40°C

P7 Wool/hand wash 30°C (1)

P8 Rinse

(1) High water level and gentle motor action. (2) Cannot be interrupted.

Rinse

Spin

Rinse

Spin

Rinse

Spin

110

Spin

Length (appr. min)

TECHNICAL INFORMATION WASHING MACHINE

MECHANICAL INSTALLATION

TRANSIT SCREWS

Before the machine can be used the three trans-

it screws must be removed as described below.

Each transit screw has a washer and a rubber

spacer. The rubber

spacers are used to

protect the screw ho-

les after the screws

have been removed.

1. First unscrew the screw and remove the was-

her.

2. Then pull out the rubber spacer.

3. Finally, refit the rubber spacers to cover the

transit holes.

WASHING MACHINE MECHANICAL INSTALLATION

POSITIONING THE WASHING MACHINE

The washing machine can be built-in or free-

standing. It should be positioned so that there

is an electrical socket within easy reach.

A. Built-in

The washing machine can be built in under a

worktop with a working height of 850–900 mm.

Leave a 5 mm gap around the machine. This

also applies between the rear edge of the top

the machine and the wall behind.

min 600 mm

min 850 mm

B. Free-standing

The washing machine can be placed alongside

or underneath the tumble dryer.

585 mm

The machine can be anchored to the floor, see

enclosed bag containing instructions and parts.

ADJUSTING THE FEET

Adjust the feet so that the machine is level and

steady on the floor.

Tighten the lock-

ing nuts.

Locking nut

CONNECTING TO WATER SUPPLY

The machine should be connected to the water

supply by someone who has the necessary skill.

The machine is connected using the supplied

inlet hose.

NOTE!

It is important that you use the inlet hose that

is supplied, not an old hose.

50 m 8

The water pressure must be 0.1–1 MPa

(about 1–10 kp/cm

; 10–100 N/cm2).

The water supply pipe must be fitted with a

shut-off valve.

595 mm

If the supply pipe has just been installed we

recommend that it is flushed out thoroughly

MECHANICAL INSTALLATION WASHING MACHINE

first to remove any dirt. Otherwise this could

clog the intake filter in the machine and block

the water supply.

WATER INTAKE – MIXED OR COLD WATER

On delivery the machine is set to use mixed hot

and cold water. The machine can be reset to use

only cold water or hot water.

CONNECTING TO THE DRAIN Machine with drain pump

The machine is supplied with a drain hose al-

ready fitted and this should be connected to a

laundry sink, or the like, at a height of 600–900

mm above the floor.

To change the water intake setting, do as follows:

Switch off the power switch, , then switch

it on again so that the machine is in start-up

mode.

Press the

button five times, then press

the 4 button five times. You have to comple-

te these ten button presses within fifteen se-

conds.

Within three seconds of pressing the 4 but-

ton for the fifth time you must then select the

type of water intake you want by pressing the

buttons.

to use cold water only (C).

to use mixed hot and cold water (E).

A letter C near the bottom right of the dis-

play shows that cold water is being used and

the letter E indicates mixed hot and cold.

600-900 mm

The lower height (600 mm) is always prefera-

ble. Make sure the drain hose is not kinked.

Machine with drain valve

An outlet hose is supplied with the machine.

This must be connected to the outlet on the

machine and

empty into a

floor drain

or gutter

drain.

NOTE!

The end of the outlet hose must be lower than

the lowest

point of the

outlet valve.

WASHING MACHINE MECHANICAL INSTALLATION

ELECTRICAL INSTALLATION

The washing machine must be connected using

a permanently installed cable through an isola-

ting switch by a qualified electrician.

Power supply

The machine is supplied, depending on market,

for one of the following supplies (see rating

plate):

A. 3-phase, 400V, 50 Hz supply, 10 A.

B. Single-phase, 230 V, 50 Hz supply, 13/16 A.

C. Single-phase, 230 V, 50 Hz supply, 10 A.

If an earth leakage circuit breaker is fitted it

must be of type A.

Reconfiguration

The machine can be reconfigured. The machi-

ne should be reconfigured as shown in the wi-

ring diagram underneath the top panel of the

machine.

NOTE!

Electrical connection /reconfiguring must be car-

ried out by a qualified electrician.

CONNECTING TO A COIN MECHANISM

Connection to a coin mechanism must be car-

ried out by a qualified electrician.

A special connecting cable is required to con-

nect the machine to a coin mechanism. This

can be ordered as a spare part, art. no. 92 090

95.

Recommendations for choice of coin mechanism

The connecting cable (92 090 95) supplies the

coin mechanism with power (230 V). The coin

mechanism must be able to short-circuit two

signal leads for a period of time (around 0–10

minutes). This is so that the user has time to

load the laundry, select the programme and start

the programme after inserting the coins.

ELECTRICAL INSTALLATION WASHING MACHINE

CHANGING SETTINGS

LANGUAGE

You can change the language of the displayed

text.

The languages you can choose from are Dansk,

Deutsch, English, Espanol, Français, Italiano,

Nederlands, Norsk, Portugués, Suomi and

Svenska.

To change language do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

button five times, then press

the 1 button five times. You have to comple-

te these ten button presses within fifteen se-

conds.

Within three seconds of pressing the 1 but-

ton for the fifth time you should then select the

language you want by pressing the 6 or

buttons.

LOCKING A PROGRAMME

If for some reason you want to limit the number

of programmes that can be used you can lock

one or more programmes.

No characters or digits are shown on the dis-

play when a locked programme is selected.

To lock or unlock a programme, do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

the

-button five times, then press

-button five times. You have to com-

plete these ten button presses within fifteen se-

conds.

Within three seconds of pressing the

button for the fifth time you should hold in the

programme button for the programme you want

to lock for 5-10 seconds until the information

in the display starts flashing.

Then you can lock the programme by relea-

sing the programme button and pressing the

-button once.

Do the same to unlock the programme.

WASH TEMPERATURE - CENTIGRADE OR FAHRENHEIT

You can change the way the temperature is dis-

played from centigrade (C) to Fahrenheit (F).

To change the temperature display, do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

button five times, then press

the 2 button five times. You have to comple-

te these ten button presses within fifteen se-

conds.

Within three seconds of pressing the

button for the fifth time you should then press

the 6 or 7 buttons to select centigrade

CHANGING PRESET WASH TEMPERATURE

You can change the preset wash temperatures

for each of the programmes. The temperatures

you can choose from are:

Heavy wash - C, 30, 35, …, 85, 90ºC.

Normal wash - C, 30, 35, …, 85, 90ºC.

Light wash - C, 30, 35, …, 85, 90ºC.

Synthetic wash - C, 30, 35, …, 85, 90ºC.

Super quick wash - C, 30, 35, …, 85, 90ºC.

Wool/hand wash - C, 30, 35, 40ºC.

WASHING MACHINE CHANGING SETTINGS

If you choose C, the wash temperature will

be the same as the intake water temperature.

To change the wash temperature, do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

button five times, then press

the 6 button five times. You have to com-

plete these ten button presses within fifteen se-

conds.

Press the programme button, 1 -

, to

select the programme you want to change the

wash temperature for.

Then use buttons

(increase time) to choose the wash tem-

(reduce time) and

perature. As you scroll through to the chosen

temperature it appears at the bottom of the

display alongside the

symbol.

When your chosen wash temperature appears

press the

button again to confirm your

choice.

Within three seconds of pressing the

but-

ton for the last time you must then press the

or 7 button to choose whether you

want the child lock on or off.

Press

to activate the child lock.

Press 6 to disable the child lock.

CHILD LOCK ON BUTTON

To prevent accidental button pushes on the

button you can activate the child lock

function. The

button then must be held

in for three seconds to activate the machine.

To switch the child lock on or off, do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

button five times, then press

the 3 button five times. You have to comple-

te these ten button presses within fifteen se-

conds.

CHANGING SETTINGS WASHING MACHINE

+ 25 hidden pages

AEG-Electrolux WASL3MW, TKSL3MW User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual