AEG-Electrolux TWSL6E100 User Manual

user manual

Condenser Dryer with Heat Pump

TWSL6E100

We were thinking of you

when we made this product

Welcome to the world of Electrolux

You’ve chosen a first class product from Electrolux,
which hopefully will provide you with lots of pleasure in
the future. Electrolux ambition is to offer a wide variety of
quality products that would make your life even more
comfortable. You can look at some examples on the
cover in this manual. But now it’s time to study this
manual and start using and enjoying the benefits from
your new machine. We promise that it’ll make your life a
little easier. Good luck!

electrolux 3

125989780-00-25092007

4 electrolux

Contents
Operating Instructions 5

Important safety information 5
Product description 8
Control panel 9
Before first use 10
Sorting and preparing laundry 11
Programme chart 12
Daily use 17
Care and cleaning 25
What to do if ... 33
Machine settings 36
Technical data 37
Consumption values 38
Hints for test institutes 38
Installation 39
Environment 43
Guarantee conditions 45

Service 46

www.electrolux.com 46

important safety information electrolux 5

Operating Instructions

Important safety information

In the interest of your safety and to ensure the correct use, before installing
and first using the appliance, read this user manual carefully, including its
hints and warnings. To avoid unnecessary mistakes and accidents, it is im­portant to ensure that all people using the appliance are thoroughly familiar
with its operation and safety features. Save these instructions and make
sure that they remain with the appliance if it is moved or sold, so that ev­eryone using it through its life will be properly informed on appliance use
and safety.

General safety

• It is dangerous to alter the specifications or attempt to modify this product in any
way.

• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person re­sponsible for their safety.

• Make sure that small pets do not climb into the drum. To avoid this, please check
into the drum before using.

• Any objects such as coins, safety pins, nails, screws, stones or any other hard,
sharp material can cause extensive damage and must not be placed into the
machine.

• In order to avoid danger of fires caused by excessive drying, do not use appliance
to dry the following items: Cushions, quilts and the like (these items accumulate
heat).

• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be
dried in the tumble dryer.

• Always unplug the appliance after use, clean and maintenance.

• Under no circumstances should you attempt to repair the machine yourself. Re­pairs carried out by inexperienced persons may cause injury or serious malfunc­tioning. Contact your local Service Centre. Always insist on genuine spare parts.

6 electrolux important safety information

• Items that have been soiled with substances such as cooking oil acetone, petrol,
kerosene, spot removers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent before being dried in the
tumble dryer.

• Danger of explosion: Never tumble dry items that have been in contact with
inflammable solvents (petrol, methylated spirits, dry cleaning fluid and the like).
As these substance are volatile, they could cause an explosion. Only tumble dry
items washed with water.

• Risk of fire: items that have been spotted or soaked with vegetable or cooking
oil constitute a fire hazard and should not be placed in the tumble dryer.

• If you have washed your laundry with stain remover you must execute an extra
rinse cycle before loading your tumble dryer.

• Please make sure that no gas lighters or matches have accidentally been left in
pockets of garments to be loaded into appliance

Never stop a tumble dry before the end of the drying cycle unless all items
are quickly removed and spread out so that the heat is dissipated.
Installation

• This appliance is heavy. Care should be taken when moving it.

• When unpacking the appliance, check that it is not damaged. If in doubt, do not
use it and contact the Service Centre.

• All packing and transit bolts must be removed before use. Serious damage can
occur to the product and to property if this is not adhered to. See relevant section
in the user manual.

• The final part of a tumble dryer cycle occurs without heat ( cool down cycle ) to
ensure that the items are left at a temperature that ensures that items will not be
damaged.

• Any electrical work required to install this appliance should be carried out by a
qualified electrician or competent person.

• Care must be taken to ensure that the appliance does not stand on the electrical
supply cable.

• If the machine is situated on a carpeted floor, please adjust the feet in order to
allow air to circulate freely.

• After having installed the appliance, check that it is not pressing or standing on
its electrical supply cable.

important safety information electrolux 7

• If the tumble dryer is placed on top of a washing machine, it is compulsory to use
the stacking kit (optional accessory).

Use

• This appliance is designed for domestic use. It must not be used for purposes
other than those for which it was designed.

• Only wash fabrics which are designed to be machine dried. Follow the instructions
on each garment label.

• Do not dry unwashed items in the tumble dryer.

• Do not overload the appliance. See the relevant section in the user manual.

• Clothes which are dripping wet should not be placed in the dryer.

• Garments which have been in contact with volatile petroleum products should
not be machine dried. If volatile cleaning fluids are used, care should be taken to
ensure that the fluid is removed from the garment before placing in the machine.

• Never pull the power supply cable to remove the plug from the socket; always
take hold of the plug itself.

• Never use the tumble dryer if the power supply cable, the control panel, the
working surface or the base are damaged so that the inside of the tumble dryer
is accessible.

• Fabric softeners, or similar products should be used as specified by the fabric
softener instructions.

• Caution - hot surface : Do not touch the door light cover surface when the light
is switched on.

1)

Child safety

• This machine is not intended for use by young children or infirm persons without
supervision.

• Children should be supervised to ensure that they do not play with the appliance.

• The packaging components (e.g. plastic film, polystyrene) can be dangerous to
children - danger of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s reach.

• Make sure that children or pets do not climb into the drum.

1) Only dryers equipped with internal drum light.

8 electrolux product description

Product description

2

3

6

7

9

12

1 Control panel
2 Drawer with condensed water container
3 Lamp for inside light
4 Fine strainer (lint filter)
5 Large mesh filter (lint filter)
6 Micro-fine filter (lint filter)
7 Rating plate
8 Loading door (reversible)

9 Base door upstream of fluff filter and heat exchanger
10 Button for opening door in plinth
11 Air slots

1

4

5

8

10

11

12 Screwed feet (with height adjustment)

Control panel

control panel electrolux 9

Aus

Wolle / Laine

Seide / Soie

Leich tbüg eln Plus /
Facile à repasser

Hemden / Chemises

Sport

Jeans

Visko se / Vi scos e

Bettwäsch e / Draps

Mix - programm /
Textiles mélangés

Mikrofaser / Microfibres

1

Programme knob and ON/OFF (Aus) switch

Arrêt

Beleu chtu ng / Ecla irag e

Baumwolle / Coton

Extratrocken / Três Sec

Starktrocken / Sec

Schranktrocken /

Prêtà Rang er

Büg eltrocken /

Prêtà Repasser

Extratrocken /

Trê s S e c

Schranktrocken /

Prêtà Rang er

Büg eltrocken /

Prêtà Repasser

Misch geweb e/Synthetiques

Zeitprogramm / Minuterie

Auffrischen / Rafraîchir

Tro c ke n g ra d

Hum i di té
Rés id uel le

U/M in
T/ Mi n

Knitterschutz

Plus

Ant ifroi ssa g e

Signal

Ala

Zeitwahl

Te m p s

rme

2 Function buttons
3 START PAUSE button
4 DELAY START (ZEITVORWAHL) (Zeitvorwahl) button
5 Status led
6 Display

Zeitvorwahl

Dep ar t Di f fe re

Start / Pause
Dep ar t / Pa u se

10 electrolux before first use

What is shown in the display

4 2

1 time to end / error message
2 cycle phase status
3 options
4 warnings
5 spin speed selection
6 dryness selection

1356

Before first use

If the appliance was not transported in an upright position, leave it to stand
for 12 hours before connecting it to the electricity supply and using it for
the first time, so that the oil can flow back to the compressor. Otherwise
the compressor could be damaged.

In order to remove any residues which may have been produced during production,
wipe the dryer drum with a damp cloth or carry out a brief drying cycle (30 MIN) with
damp cloths in the machine.

sorting and preparing laundry electrolux 11

Sorting and preparing laundry

Sorting laundry

• Sort by fabric type:
– Cotton/linen for programmes in COTTONS (Baumwolle) pogramme group.
– Mixtures and synthetics for programmes in SYNTHETICS (Mischgewebe) pro-

gramme group.

• Sorting by care label. The care labels mean:

Drying in the tum­ble dryer possible

in principle

Do not place in the appliance any wet laundry which is not specified on the
care label as being suitable for tumble-drying.
This appliance can be used for all wet laundry items which are labelled as
suitable for tumble-drying.

• Do not dry new, coloured textiles together with light-coloured laundry items. Tex­tile colours may bleed.

• Do not dry cotton jersey and knitwear with the EXTRA programme. Items may
shrink!

• Wool and wool-like textiles can be dried using the WOOL (WOLLE) programme.
Before the drying cycle spin the woollen textiles as well as possible (max. 1200
rpm). Only dry woollen textiles together which are similar or the same with repect
to material, colour and weight. Please dry heavy laundry items made of wool
separately.

Preparing laundry

• To avoid laundry becoming tangled: close zips, button up duvet covers and tie
loose ties or ribbons (e.g. of aprons).

• Empty pockets. Remove metal items (paper clips, safety pins, etc).

• Turn items with double-layered fabrics inside out (e.g. with cotton-lined anoraks,
the cotton layer should be outermost). These fabrics will then dry better.

Drying at normal

temperature

Drying at reduced

temperature

Drying in the tum­ble dryer not pos-

sible

12 electrolux programme chart

Programme chart

Additional func-

tions/options

Programmes

EXTRA
(EXTRA
TROCKE
N)

STRONG
(STARK
TROCKE
N)

CUP-

COTTONS (BAUMWOLLE)

BOARD
(SCHRA
NKTROC

1)

KEN)

1)

IRON

RPM

BUZZER

TIME (ZEITWAHL)

max. load (weight when dry)

LONG ANTI-CREASE

DRYNESS (TROCKENGRAD)

7 kg • • • • - •

7 kg • • • • - •

7 kg • • • • - •

7 kg • • • • - •

Application/properties

DELAY START (ZEITVORWAHL)

Thorough drying of thick or
multi- layered fabrics, e.g.
terry towelling items, bath­robes, cottons.

Thorough drying of thick
fabrics, e.g. terry towelling
items, towels, cottons.

Thorough drying of fabrics
of even thicknesses, e.g.
terry towelling items, knit­wear, towels, cotton shirts.

For normal thickness cot­ton or linen laundry, e.g.
bedding, table linen.

Care

mark

Additional func-

tions/options

programme chart electrolux 13

Programmes

EXTRA
(EXTRA
TROCKE
N)

CUP­BOARD
(SCHRA
NKTROC

1)

KEN)
IRON

(BÜGELT

SYNTHETICS (MISCHGEWEBE)

ROCKEN
)

TIME
(ZEITPR
OGRAM
M )

TIME (ZEIT)

FRESHE
N UP
(AUFFRI­SCHEN)

RPM

BUZZER

TIME (ZEITWAHL)

max. load (weight when dry)

LONG ANTI-CREASE

DRYNESS (TROCKENGRAD)

3 kg • • • • - •

3 kg • • • • - •

3 kg • • • • - •

7kg - - - - • •

1 kg - - - - • •

Application/properties

DELAY START (ZEITVORWAHL)

Thorough drying of thick or
multi-layered fabrics, e.g.
pullovers, bedding, table
linen.

For thin fabrics which are
not ironed, e.g. easy care
shirts, table linen, socks,
lingerie with bones or wires.

For thin fabrics which are
also to be ironed, e.g. knit­wear, cotton shirts.

For further drying of
individual items of laundry
or for small volumes of less
than 1kg.

For refreshing or gently
cleaning textiles with
commercially available dry
cleaning products.

Care

mark

14 electrolux programme chart

Additional func-

tions/options

Programmes

RPM

max. load (weight when dry)

DRYNESS (TROCKENGRAD)

MICRO­FIBER
(MIKROF

SPECIAL

ASER)

1 kg • • • • - •

MIXED
(MIX­PRO-

3 kg • • • • - •

GRAMM )
BED

LINEN
(BETTWÄ

3 kg • • • • - •

SCHE)
VISCOSE

(VIS-

1 kg • • • • - •

KOSE)

JEANS 7 kg • • • • - •

Application/properties

BUZZER

TIME (ZEITWAHL)

LONG ANTI-CREASE

DELAY START (ZEITVORWAHL)

For thin fabrics, polyester
and polyamide, which are
not ironed.

For drying cotton and
synthetic fabrics, uses low
temperature.

Bed linen (single and dou­ble sheet, pillowcase, bed­spread, duvet cover).

For thin fabrics, viscose,
and polyester, which are
not ironed.

For leisure clothing, such as
jeans, sweat-shirts, etc., of
different material
thicknesses (e.g. at the
neck, cuffs and seams).

Care

mark

Additional func-

tions/options

programme chart electrolux 15

Programmes

SPORTS
LIGHT
SPORT­KLEI­DUNG)

SHIRTS
(HEM­DEN)

RPM

max. load (weight when dry)

DRYNESS (TROCKENGRAD)

BUZZER

TIME (ZEITWAHL)

LONG ANTI-CREASE

2 kg • • • • - •

1.5
kg

(or 7

• • • • - •

shirt

s)

Application/properties

DELAY START (ZEITVORWAHL)

For sportswear, thin fab­rics, polyester, which are
not ironed.

Special program with anti­crease mechanism for easy
care fabrics such shirts and
blouses; for minimum iron­ing effort. The results de­pends on the type of fabric
and its finish. Place fabrics
in the dryer straight after
spinning; once dried,
immediately remove fabrics
and place on a clothes
hanger.

Care

mark

16 electrolux programme chart

Additional func-

tions/options

Programmes

EASY
IRON
PLUS
(LEICHT
BÜGELN
PLUS)

SILK
(SEIDE )

RPM

max. load (weight when dry)

DRYNESS (TROCKENGRAD)

BUZZER

TIME (ZEITWAHL)

LONG ANTI-CREASE

1 kg
(or 5

• • • • - •

shirt

s)

1 kg • • • • - -

Application/properties

DELAY START (ZEITVORWAHL)

Special program with anti­crease mechanism for easy
care fabrics such shirts and
blouses; for minimum iron­ing effort. The results de­pends on the type of fabric
and its finish. Place fabrics
in the dryer straight after
spinning; once dried,
immediately remove fabrics
and place on a clothes
hanger.

For drying silk using warm
air and gentle movement.

Care

mark

Additional func-

tions/options

daily use electrolux 17

Programmes

max. load (weight when dry)

WOOL
(WOLLE)

1) In accordance with IEC61121

1 kg • • • • - -

Daily use

DRYNESS (TROCKENGRAD)

Application/properties

RPM

BUZZER

TIME (ZEITWAHL)

LONG ANTI-CREASE

DELAY START (ZEITVORWAHL)

For drying woollen fabrics
after they have been
washed, using warm air at
minimum mechanical load
(Follow section “Sorting
and preparing washing”).
Recommendation: Remove
fabrics immediately after
drying, as no anti-crease
programme follows.

Care

mark

Switching machine on / switching light on

Turn the programme selector to any programme or turn it to LIGHT (BELEUCH­TUNG). The machine has been switched on. When the loading door is opened, the
drum is illuminated.

18 electrolux daily use

Opening loading door / loading laundry

1.

Open loading door:
Use force to push against the loading door (push point)

2. Load your laundry (do not force it in).

Do not jam laundry in between the loading door and rubber seal.

3. Close loading door securely. Lock must audibly lock.

Selecting the programme

Use the programme selector to set the programme you require. The estimated time
to end of the programme appears in the LCD in h:mm format (hours:minutes).
During the cycle time elapses by steps of one minute; less than 1 hour the leading
zeros are not shown (ex. “59”, “5”, “0”).

Setting dryness level

Zeitvorwahl

Depart Differ

daily use electrolux 19

e

U/Min
T/Min

Knitterschutz

Plus

Antifroissage

Signal

Alarme

Zeitwahl

Tem p s

Start / Pause
Depart / Pause

Trockengrad

Humidité
Résiduelle

If laundry comes out of the machine too damp after a standard drying programme,
you can increase the drying result by using the DRYNESS (TROCKENGRAD) func­tion. Laundry becomes drier as you move from MIN to MAX.

Press the DRYNESS (TROCKENGRAD) button repeatedly until the desired dry­ness level (MIN, MED or MAX) is shown in the display. When humidity adjustment
is not foreseen on the related program, bar frame with AUTO text is shown.
If wool or silk comes out of the machine too damp at the end of a WOOL (WOLLE)
or SILK (SEIDE) programme, you can dry it again by restarting the appropriate pro­gramme, this time with the DRYNESS (TROCKENGRAD) function selected and
dryness level MIN, MED or MAX. In the case of a drying cycle with relatively dry
laundry, the length of the programme cycle displayed at the beginning is corrected
after a while.

Setting the pre-drainage spin speed

If the washing in the washing machine was initially drained prior to the drying cycle,
the dryer can be set according to the spin speed of the initial drainage procedure.
The higher the spin speed was, the shorter the programme length for the drying
cycle.

vorwahl

Zeit

e

fer

Depart Dif

Tro c k

Humidité

Résiduelle

engrad

U/Min
T/Min

Knitterschutz

Plus

Antifroissage

Signal

Alarme

Zeitwahl

Tem p s

Start / Pause
Depart / Pause

20 electrolux daily use

Press the RPM (T/MIN.) (U/MIN) button a number of times until the desired spin
speed of the initial drainage is displayed. No value is shown if no spin speed is
selected.

In certain programmes the spin speed has not effect (time controlled cycles), its
selection can be not selectable and only three dashes are visualized. Available se­lections:

Buzzer

Zeitvorwahl

e

fer

Depart Dif

U/Min
T/Min

Knitterschutz

Plus

Antifroissage

Signal

Alarme

Zeitwahl

Tem p s

Start / Pause
Depart / Pause

Tro c kengrad

Humidité
Résiduelle

The appliance is supplied with the BUZZER (SIGNAL) function deactivated.
To activate buzzer press BUZZER (SIGNAL) button.
The button is used to switch the function on or off. When the function is active, the
BUZZER

(SIGNAL) symbol appears in the display.

The buzzer sounds or plays a tune during:
– cycle end
– anti-crease phase and when phase starts or ends
– cycle interruption by a warning
–alarm

Setting long anti-crease function

Zeitvorwahl

e

fer

Depart Dif

U/Min
T/Min

Knitterschutz

Plus

Antifroissage

Signal

Alarme

Zeitwahl

Tem p s

Start / Pause
Depart / Pause

Tro c kengrad

Humidité
Résiduelle

daily use electrolux 21

Press the LONG ANTI-CREASE (KNITTERSCHUTZ PLUS) button. A 90 minute
anti-crease phase is set. The display now shows the LONG ANTI-CREASE
(KNITTERSCHUTZ PLUS) icon. If this additional function is selected, the anti-crease
phase at the end of the drying cycle is lengthened by 60 minutes. The laundry can
be removed at any time during the anti-crease phase.

Time

Zeitvorwahl

e

fer

Depart Dif

U/Min
T/Min

Knitterschutz

Plus

Antifroissage

Signal

Alarme

Zeitwahl

Tem p s

Start / Pause
Depart / Pause

Tro c kengrad

Humidité

Résiduelle

To select the programme duration after setting the TIME programme (ZEIT-Pro­gramm). You can select a programme duration from 10 mins to 3 hrs in 10-minute
steps.

1. Turn the programme knob to the TIME programme (ZEIT-Programm). The blink­ing 10' above TIME (ZEITWAHL) button is on. (corresponding to the COOLING
programme).

2. Press the TIME (ZEITWAHL) button repeatedly until the desired programme du­ration is shown in the display, e.g. 20 for a programme of 20 minutes.

If the programme duration is not selected, the duration is automatically set to 10
mins.

Setting delay timer

vorwahl

Zeit

e

rt Differ

Depa

U/Min
T/Min

Knitterschutz

Plus

Antifroissage

Signal

Alarme

Zeitwahl

Temps

Start / Pause
Depart / Pause

Tro c kengrad

Humidité
Résiduelle

With the DELAY (ZEITVORWAHL) button, you can delay the start of a pro­gramme by between 30 minutes (30') and a maximum of 20 hours (20h).

22 electrolux daily use

1. Select the programme and additional functions.

2. Press the DELAY (ZEITVORWAHL) button as many times as necessary until the
required start delay appears on the display, e.g. 12h if the programme is to be
started in 12 hours.

If the display is showing 20h and you press the button again, the time delay
will be cancelled. The display will show 0'and then the duration of the se­lected programme.

3. To activate the delay timer, press the START PAUSE button. The amount of time
remaining until the programme is set to start is continuously displayed (e.g. 15h,
14h, 13h, … 30' etc).

Setting child lock

The child lock can be set to prevent a programme being accidentally started or a
programme in operation being accidentally changed. The child lock function locks
all buttons and the programme knob. The child lock can be activated or deactivated
by holding down the LONG ANTI-CREASE (KNITTERSCHUTZ) and BUZZER (SIG­NAL) buttons simultaneously for 5 seconds.

– Before programme is started: Appliance cannot be used
– After programme is started: Programme in operation cannot be changed

The ( icon appears in the display to indicate that the child safety device is activated.
The child safety device is not deactivated once the programme comes to an end.
If you want to set a new programme, you must first deactivate the child safety de­vice.

daily use electrolux 23

Starting the programme

Press the START PAUSE button. The programme is started.
The programme progress is shown in LCD by appropriate set of icons. From left to
the right, from IRON DRY
cycle chosen. E. g. in case of CUPBOARD programme the following status icons
are visible:
under status icon. When appropriate part of drying cycle is accomplished dash
becomes steady and appears flashing under next status icon.

. Current cycle progress is marked by flashing dash

to ANTI-CREASE icon depends on the drying

Changing programme

To change a programme which has been selected by mistake once the programme
has started, first turn the programme selector to OFF and then reset the pro­gramme.

The programme can no longer be changed directly once the programme
has started. If nevertheless there is an attempt to change the programme
on the programme knob, the programme progress display and the main­tenance indicators flash. If an option button (excluding the BUZZER (SIG­NAL) button) is pressed, Err appears in the multidisplay. The drying
programme is not however affected by this (laundry protection).

Putting in extra items or taking items out before end of programme

1. Open loading door.

Laundry and drum can become hot. Risk of burns!

2. Load or remove laundry items.

24 electrolux daily use

3. Close loading securely. Lock must audibly lock.

4. Press the START PAUSE button to continue the drying cycle.

Drying cycle complete / removing laundry

Once the drying cycle is complete, display shows a blinking "0", under anti­crease
an acoustic signal sounds intermittently for about one minute.

The drying cycles (except for the WOOL (WOLLE) programme) are
automatically followed by an anti-crease phase which lasts around 30 mi­nutes. The drum rotates at intervals during this phase. This keeps the
laundry loose and free of creases. The laundry can be removed at any time
during the anti-crease phase. (The laundry should be taken out towards the
end of the anti-crease phase at the latest to prevent creases from forming.)
If LONG ANTI-CREASE
phase is lengthened by 60 minutes.

1. Open door.

2. Before removing the laundry, remove fluff from the micro-fine filter. It is best to

3. Remove laundry.

4.

icon appear dash. If the BUZZER (SIGNAL)button has been pressed,

function has been selected, the anti-crease

use a damp hand for this purpose. (See “Care and cleaning” chapter.)

Turn the programme selector to OFF (AUS).

After each drying cycle:

- Clean the micro-fine filter and fine filter

- Drain the condensed water container
(See chapter “Care and cleaning”.)

5. Close the door.

electrolux 25

Care and cleaning

Cleaning fluff filter

The filters collect all the fluff which accumulates during drying. To ensure that the
dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be
cleaned after every drying cycle.
The warning icon

Never operate the dryer without fluff filters or with damaged or blocked fluff
filters.

1.

is on to remind you this operation.

Open loading door

2. Use a damp hand to clean the micro- fine filter, which is built into the lower part

of the loading aperture.

3. After a period of time, a patina due to detergent residue on laundry forms on

the filters. When this occurs, clean the filters with warm water using a brush.
Remove the filter from the door pulling it out. It can be positioned with the tooth
facing to the left or to the right).
After cleaning do not forget to put it back.

26 electrolux care and cleaning

4.

Push down unlock button on large mesh filter.
Large mesh filter jumps up.

5.

Take out fine strainer.

6. Remove fluff from fine strainer. It is best to use a damp hand for this purpose.

Clean the entire filter area

The strainer area does not have to be cleaned after every drying cycle, but
should be checked regularly and cleaned of fluff if necessary.

7. To do this, grip the top of the large mesh filter and pull it forwards until it comes

loose from the two brackets.

care and cleaning electrolux 27

8.

Remove fluff from the entire filter area. It is best to use a vacuum cleaner for this
purpose.

9. Press both journals of the large mesh filter into the brackets on the loading door

until they snap into place.

10. Re-insert fine strainer.

11. Press against the large mesh filter until it locks into the interlock.

If the fine strainer is not fitted, the large mesh filter will not snap into place
and the loading door cannot be closed.

Cleaning the door seal

Wipe the door seal with a damp cloth immediately after the drying cycle has finished.

Emptying the condensate tank

Empty condensate tank after every drying cycle.

28 electrolux care and cleaning

If the condensate tank is full, an active programme will break off automatically and
the EMPTY CONTAINER
the programme, the condensate tank must first be emptied.

The condensate is not suitable for drinking or for preparing foodstuffs.

icon on the display will light up. In order to continue

1.

2

1

Take out drawer containing condensed water container completely 1 and pull
up the condensed water container’s drainage pipe as far as it will go 2.

2.

Pour condensed water out into a basin or similar receptacle.

3. Slide outlet connections in and refit condensate tank.
If the programme has been interrupted as a result of the condensate tank being
full: Press the START PAUSE button to continue the drying cycle.

The condensate tank has a volume of approx. 4 litres. This is sufficient for
around 7kg of laundry which has previously been spun at 1000 revolutions/
minute.

care and cleaning electrolux 29

The condensate can be used as distilled water, e.g. for steam ironing.
However first filter the condensate (e.g. with a coffee filter) to remove any
residue and small pieces of fluff.

Cleaning heat exchanger filter

If the indicator CLEAN BASE FILTER lights up, the heat exchanger filter in the
base of the appliance must be cleaned.

To protect the heat pump from dirt, the dryer is fitted with fluff filter, which
is located in the filter housing. Here too large amounts of fluff build up over
time, which affect the function of the appliance.

IMPORTANT

• Operating when the fluff filter is clogged with fluff can damage the dryer.

This also increases energy consumption.

• Never operate the dryer without the fluff filters.

• Do not use the dryer without the fluff filter. A dirty heat pump requires

more energy and can only be cleaned up by means of a costly process.

1.

Open loading door

2. Open door in plinth: To do this, press the release button on the bottom of the

door aperture and open the door in the plinth to the left.

30 electrolux care and cleaning

3.

Pull filter housing out of the base by the handle.

4. Clean the inside of the door, the fluff filter chamber and the rubber seals of fluff.

5.

Remove fluff from the fluff filter on the floor of the base with a damp hand.

6.

2

1

To clean the fluff filter: Remove filter from filter housing. To do this, press the
pressure points on the sides and pull the filter frame up and out of the housing.

care and cleaning electrolux 31

7.

Remove fluff from the fluff filter with a damp hand.

8. Insert the fluff filter into the filter housing.

9.

As necessary, approx. once every 6 months, remove the fluff from the heat
exchanger using the sponge supplied. When doing this, please use rubber
gloves.
Tip: The fluff can be removed more easily if it is first dampened e. g. with a
laundry dampener.

10. Re-insert filter housing along with filter in appliance base.

Note: If the fluff filter is not inserted in the filter housing, the filter housing cannot
be slid into the appliance base.

11. Close door in plinth.

Cleaning the drum

Do not use abrasives or steel wool to clean the drum.

32 electrolux care and cleaning

Lime in the water or cleaning agents may form a barely visible lining on the
inside of the drum. The degree to which the laundry has been dried is then
no longer detected reliably. The laundry is damper than expected when re­moved from the dryer.
Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down
the inside of the drum and drum ribs.

Clean operating screen and housing

Do not use furniture cleaners or aggressive cleaning agents to clean the
machine.
Use a damp cloth to wipe down the operating screen and housing.

what to do if ... electrolux 33

What to do if ...

Troubleshooting by yourself

If, during operation, the error code E... plus number or letter) appears on the LCD:
Switch the machine off and on again. Reset programme. Press the START PAUSE
button If the error is still displayed, please inform your local Service Force Centre
and quote the error code.

Problem Possible cause Remedy

Dryer does not work.

Drying results
unsatisfactory.

Loading door does not
close.

Mains plug is not plugged
in or fuse is not working
correctly.

Loading door is open. Close loading door.
Have you pressed the

START PAUSE button?

Wrong programme selec­ted.

Lint filters clogged. Clean lint filters.
Fluff filter clogged. Clean fluff filter.

Overloading of laundry.

Ventilation slots in base
area covered up.

Residue on inside surface
of drum or drum ribs.

Fine strainer not in place
and/or mesh filter not
locked in place.

Plug in at mains socket.
Check fuse in fuse box
(domestic installation).

Press the START PAUSE
button again.

Select a different pro­gramme the next time you
dry (see “Programme
chart” chapter).

Observe recommended
loading volumes.

Uncover ventilation slots
in base area.

Clean inside surface of
drum and drum ribs.

Make an adjustment us­ing the DRYNESS func­tion (see chapter ”Daily
use”)

Install fine strainer and/or
snap large mesh filter into
place.

34 electrolux what to do if ...

When a button is pressed,
Err appears on the LCD.

Drum light does not work.

Displayed programme
time changes erratically or
stays unchanged for a
long time.

Programme inactive,
empty water tank
is on.

Drying cycle ends shortly
after programme starts.
END display illuminated.

Drying cycle lasts an
unusually long time. Note:
After around 5 hours the
drying cycle ends
automatically (see „Drying
cycle complete ”).

icon

Washing protection. After
the start of the pro­gramme, the option can
no longer be set.

Programme selector in
OFF position.

Defective light bulb.

Programme time is cor­rected automatically de­pending on type and vol­ume of laundry and level
of dampness.

Condensate tank is full.

Not enough washing loa­ded or washing loaded is
too dry for selected pro­gramme.

Lint filter clogged. Clean lint filter.
Fluff filter clogged. Clean fluff filter.
Load volume too big. Reduce load volume.
Laundry insufficiently

spun.
Particularly high room

temperature. Temporary
switching off of the com­pressor to avoid overload.

Turn the programme
knob to OFF. Set the pro­gramme again.

Turn programme selector
to LIGHT or to any pro­gramme.

Replace light bulb (see
next section).

Automatic process; this is
not a machine fault.

Empty condensate tank,
then start programme
with START PAUSE but­ton.

Select time programme
or higher drying level (e.g.
INTENSIVE DRY instead
of STORAGE DRY).

Laundry must be
adequately spun.

Automatic process, there
is no fault with the appli­ance. If possible, lower
the room temperature.

Changing the bulb for interior lighting

Only use a special bulb which is designed specially for dryers. The special bulb can
be obtained from the Customer Care Department, ET no. 112 552 000-5.

what to do if ... electrolux 35

When the appliance is switched on, the interior lighting switches itself off
after 4 minutes when the door is open.

Do not use standard bulbs! These develop too much heat and may damage
the machine!

Before replacing the bulb, disconnect the mains plug.

1. Unscrew cover above the bulb (this can be found directly behind the loading
aperture, at the top; refer to “Description of machine” section.)

2. Replace defective bulb.

3. Screw cover back down.

Check the correct positioning of o-ring gasket before screwing back the door light
cover. Do not operate the dryer when missing o-ring gasket on door light cover.

For safety reasons, the cover must be screwed down tightly. If this is not
done, the dryer must not be operated.

36 electrolux machine settings

Machine settings

Setting Implementation

BUZZER permanent off

Water hardness

Water contains, a variable
quantity of limestone and
mineral salts of which quan­tities vary according to
geographical locations thus
varying its conductivity val­ues.
Relevant variations of the
conductivity of the water
compared to those prefixed
by the factory could slightly
influence the residual
humidity of the laundry at
the end of the cycle. Your
dryer allows you to regulate
the sensitivity of the drying
sensor based on
conductivity values of the
water.

1. Turn the programme selector to any pro­gramme.

2. Press simultaneously the DRYNESS
(TROCKENGRAD) and RPM (U/MIN.) but­tons and hold down for approx. 5 seconds.

3. The buzzer is by default always off. You can
use BUZZER (SIGNAL) button to activate or
deactivate sound but machine does not
memorize your selection.

1. Turn the programme selector to any pro­gramme.

2. Press simultaneously the DRYNESS
(TROCKENGRAD) and TIME (ZEITWAHL)
buttons and hold down for approx. 5 sec­onds. The current setting is on the display:

–
–

–

3. Press the START PAUSE button sequentially
until you set desired level.

4. To memorize setting press simultaneously
the DRYNESS (TROCKENGRAD) and TIME
(ZEITWAHL) buttons or turn knob to OFF
(AUS) position

low conductivity <300 micro S/cm
medium conductivity 300-600 mi-

cro S/cm

high conductivity >600 micro S/

cm

technical data electrolux 37

Emptying water tank - warn­ing message permanent off

When using an external
drain for the condensed wa­ter.

Technical data

This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Di-

rective 92/31/EEC

– 93/68/EEC dated 22.07.1993 CE Marking Directive

1. Turn the programme selector to any pro­gramme.

2. Press simultaneously the RPM (U/MIN.) and
TIME (ZEITWAHL) buttons and hold down
for approx. 5 seconds.
The current setting is on the display:

– warning

message is off

– warning

message is switched on

By default the warning message is
switched on and displayed always at the
end of the drying cycle or during the cycle
if the water container is full.

icon and - warning

icon and - warning

Height x width x depth 85 x 60 x 60 cm
Depth with loading door open 109 cm
Height can be adjusted by 1.5 cm
Weight when empty approx. 60kg
Loading volume (depends on pro-

gramme)

1)

max. 7kg

38 electrolux consumption values

Energy consumption in accordance
with IEC 61121 s. e. (7kg of cotton,

pre-drained at 1000 rpm, COTTON

2,4 kWh

CUPBOARD DRY programme)
Use Domestic
Permissible ambient temperature + 5°C to + 35°C

1) Different loading volume data may be needed in some countries as a result of different measuring
methods.

Consumption values

The consumption values have been established under standard conditions. They
may deviate when the machine is operated in domestic circumstances.

Programme Loading volume in kg

COTTON CUPBOARD DRY
COTTON IRON DRY

1)

SYNTHETICS CUPBOARD

2)

DRY

1) pre-drained at 1000 rpm

2) pre-drained at 1200 rpm

1)

7 2.4
7 1.8

3 0.75

Energy consumption

in kWh

Hints for test institutes

Parameters possible to checked by the Test Institutes:

• Energy consumption (corrected with final humidity) during the cupboard dry cot-

ton cycle with nominal load.

• Energy consumption (corrected with final humidity) during the cupboard dry cot-

ton cycle with half load.

• Final humidity (during Cupboard dry cotton, Iron dry cotton and Cupboard dry

Easy care)

• Condensation efficiency (corrected with final humidity) during cupboard dry cot-

ton cycle with nominal and half load

installation electrolux 39

All the cycles have to be checked in accordance with IEC 61121 (Tumble dryers for
household use – Methods for measuring the performance).

Installation

Transporting the appliance

Only tip the appliance on its left side to transport (see illustration), if it can­not be transported in an upright position.

Appliance positioning

• It is recommended that, for your convenience, the machine is positioned close to

your washing machine.

• The tumble dryer must be installed in a clean place, where dirt does not build up.

• Air must be able to circulate freely all round the appliance. Do not obstruct the

front ventilation grille or the air intake grilles at the back of the machine.

40 electrolux installation

• To keep vibration and noise to a minimum when the dryer is in use, it should be

placed on a firm, level surface.

• Once in its permanent operating position, check that the dryer is absolutely level

with the aid of a spirit level. If it is not, raise or lower the feet until it is.

• The feet must never be removed. Do not restrict the floor clearance through

deeppile carpets, strips of wood or similar. This might cause heat built-up which
would interfere with the operation of the appliance.

The hot air emitted by the tumble dryer can reach temperatures of up to 60°
C. The appliance must therefore not be installed on floors which are not
resistant to high temperatures.
When operating the tumble dryer, the room temperature must not be lower
than +5°C and higher than +35°C, as it may affect the performance of the
appliance.

Should the appliance be moved, it must be transported vertically.

The appliance must not be installed behind the lockable door, a sliding door
a door with a hinge on the opposite side to that of the appliance.

Changing door stop

The door stop may only be changed by a specialist. If necessary, please contact
our after-sales service or your specialist dealer.

Before changing the door stop, disconnect the mains plug.

installation electrolux 41

AC

B

A

1. Open loading door.

2. Unscrew hinge A from the front of the machine and take off the loading door.

3. Remove cover plates B and C. To do this, insert a thin screwdriver into the slots

as shown in the illustration, press downwards slightly and pry out the cover
plates.

4.

Use an appropriate tool and exert pressure to unfasten locking block D from
the snap-on fixture, take out and re-insert on the other side having rotated the
block through 180°.

5. Unscrew hinge A from the loading door, rotate through 180°, re-insert on the

opposite side and screw down.

6. Re-insert cover plates B and C on the opposite site having first rotated them

through 180°.

D

C

42 electrolux installation

E

F

E

G

F

G

7. Unscrew cover plates E from the front of the machine, rotate through 180°,

screw on the opposite side.

8. Unscrew door lock F, push down slightly and remove from the front of the

machine.

9. Disconnect cable connector from door lock F.

10. Press snap-in button G in and down, press cover down slightly and remove

from front of the machine.

11. Disconnect cable connector from cover G.

12.

Change door lock F over to the opposite side, insert the cable connector and
screw down the door interlock.

13. On the other side, insert the cable connector in cover G, insert cover and allow

snap-in button to lock into place.

14. Insert loading door and hinges into recesses on the front of the machine and

screw down.
Note regarding contact protection:The machine is only secure for operations
again once all plastic parts have been inserted.

Special accessories

Intermediate installation kit for stacked washer and dryer:

environment electrolux 43

Available from your Service Force Centre or your specialist dealer

These intermediate installation kits can be used to arrange the dryer and an
automatic AEG-Electrolux washing machine (60cm wide, front loading) as a space­saving washer/dryer stack. The automatic washing machine is at the bottom and
the dryer is at the top.
Version to be supplied:
– with extractable stacker plate 916.018 903
Read carefully the instructions supplied with the kit.

Installation kit for external condensate drain

Attached to your product

Installation kit 125 122 510 for direct draining of condensate into a basin, siphon,
gully, etc. The condensate tank then no longer has to be drained, it must however
remain in its intended position in the machine. Refer to the “Programme options”
section for how to deactivate the EMPTY WATER TANK
Max. displacement height: 1m from the base of the dryer; max. displacement length:
3m
Read carefully the instructions supplied with the kit.

alert.

Environment

Packaging material

The packaging materials are environmentally friendly and can be recycled. The
plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dis­pose of the packaging materials in the appropriate container at the community
waste disposal facilities.

Old appliance

The symbol on the product or on its packaging indicates that this product may
not be treated as household waste. Instead it should be taken to the appropriate
collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative con-

44 electrolux environment

sequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. For more detailed infor­mation about recycling of this product, please contact your local council, your
household waste disposal service or the shop where you purchased the product.
The heat pump of your dryer contains a closed refrigerant circuit filled with a refrig­erant which is free from fluoro-chloro-hydrocarbons. The refrigerant circuit in the
heat pump must not be damaged.

Remove mains plug from socket when you have no further use for the ma­chine. Cut off mains cable and dispose of together with plug. Destroy
loading door hook. Children cannot then lock themselves in the machine
and put their lives at risk.

Environmental tips

• In the dryer, laundry becomes fluffy and soft. Fabric softeners are not therefore

needed when washing.

• Your dryer will function most economically if you:

– always keep the ventilation slots on the base of the dryer unobstructed;
– use the loading volumes specified in the programme overview;
– ensure you have good ventilation in the installation room;
– clean the micro-fine filter and fine strainer after each drying cycle;
– spin the laundry well before drying. Example: Consumption data – depending

on spinning speed – for 7kg of laundry, dried using the COTTONS CUPBOARD
DRY programme.

Pre-draining Drying cycle

Revolutions

per minute

Residual dampness

in litres as a %

Energy in kWh

1000 4.20 60 2,4 0,36
1200 3.92 56 2,3 0,34
1400 3.64 52 2,2 0,33
1800 3.15 45 2,0 0,30

1) Tariff: 0.15 Euro/kWh

Costs in eu-

1)

ros

Guarantee conditions

guarantee conditions electrolux 45

European Guarantee

This appliance is guaranteed by Electro­lux in each of the countries listed at the
back of this user manual, for the period
specified in the appliance guarantee or
otherwise by law. If you move from one
of these countries to another of the
countries listed, the appliance guarantee
will move with you subject to the follow­ing qualifications:-

• The appliance guarantee starts from

the date you first purchased the ap­pliance which will be evidenced by
production of a valid purchase docu­ment issued by the seller of the appli­ance.

• The appliance guarantee is for the

same period and to the same extent
for labour and parts as exists in your

new country of residence for this
particular model or range of applian­ces.

• The appliance guarantee is personal
to the original purchaser of the appli­ance and cannot be transferred to
another user.

• The appliance is installed and used in
accordance with instructions issued
by Electrolux and is only used within
the home, i.e. is not used for com­mercial purposes.

• The appliance is installed in accord­ance with all relevant regulations in
force within your new country of resi­dence.

The provisions of this European Guar­antee do not affect any of the rights
granted to you by law.

46 electrolux www.electrolux.com

Service

In the event of technical faults, please first check whether you can remedy the
problem yourself with the help of the operating instructions (Chapter “What to do
if…”).
If you were not able to remedy the problem yourself, please contact the Customer
Care Department or one of our service partners.

In order to be able to assist you quickly, we require the following information:
– Model description
– Product number (PNC)
– Serial number (S No.) (for numbers, see rating plate)
– Type of fault
– Any error messages displayed by the appliance
So that you have the necessary reference numbers from your appliance at hand,
we recommend that you write them in here:

Model description: ................................................................................

PNC: .....................................................................................................

S No.: ...................................................................................................

www.electrolux.com

Albania [phone] Rr. Pjeter Bogdani Nr. 7

Tirane

Belgique/België/Belgien [phone] Bergensesteenweg 719,

1502 Lembeek

Česká republika [phone] Budějovická 3, Praha 4,

140 21

www.electrolux.com electrolux 47

Danmark [phone] Sjællandsgade 2, 7000

Fredericia

Deutschland [phone] Muggenhofer Str. 135,

90429 Nürnberg

Eesti [phone] Pärnu mnt. 153, 11624

Tallinn

España [phone] Carretera M-300, Km.

29,900 Alcalá de Henares

Madrid
France www.electrolux.fr
Great Britain [phone] Addington Way, Luton,

Bedfordshire LU4 9QQ
Hellas [phone], Limnou Str., 54627

Thessaloniki
Hrvatska [phone] Slavonska avenija 3,

10000 Zagreb
Ireland [phone] Long Mile Road Dublin 12
Italia [phone] C.so Lino Zanussi, 26 -

33080 Porcia (PN)
Latvija [phone] Kr. Barona iela 130/2,

LV-1012, Riga
Lietuva [phone] Ozo 10a, LT-08200 Vil-

nius
Luxembourg [phone] Rue de Bitbourg, 7,

L-1273 Hamm
Magyarország [phone] H-1142 Budapest XIV,

Erzsébet királyné útja 87
Nederland [phone] Vennootsweg 1, 2404

CG - Alphen aan den Rijn
Norge [phone] Risløkkvn. 2 , 0508 Oslo
Österreich [phone] Herziggasse 9, 1230

Wien

48 electrolux www.electrolux.com

Polska [phone] ul. Kolejowa 5/7,

Warszawa
Portugal [phone] Quinta da Fonte - Edificio

Gonçalves Zarco - Q 35

-2774-518 Paço de Ar-

cos
Romania [phone] Str. Garii Progresului 2,

S4, 040671 RO
Schweiz - Suisse - Sviz-

zera

[phone] Industriestrasse 10,

CH-5506 Mägenwil
Slovenija [phone] Gerbičeva ulica 98, 1000

Ljubljana
Slovensko [phone] Electrolux Slovakia s.r.o.,

Electrolux Domáce spo-

trebiče SK, Seberíniho 1,

821 03 Bratislava
Suomi www.electrolux.fi
Sverige [phone] Electrolux Service, S:t

Göransgatan 143, S-105

45 Stockholm
Türkiye [phone] Tarlabaşı caddesi no : 35

Taksim İstanbul

Россия [phone] 129090 Москва,

Олимпийский проспект,

16, БЦ "Олимпик"

Україна [phone] 04074 Київ,

вул.Автозаводська, 2а,

БЦ "Алкон"

electrolux 49

50 electrolux

www.electrolux.com

www.electrolux.com

125989780-00-25092007