AEG-Electrolux SN81840-4I User Manual

SANTO N 8 18 40-4 i

Integrierbare Kühl-Gefrierkombination

Integrating Fridge Freezer

Integrerbare Kjøle-frysekombinasjoner

Gebrauchs- und Einbauanweisung

Operating and Installation Instructions

Bruksanvisning

AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg

http://www.aeg.hausgeraete.de

Technische Änderungen vorbehalten
© Copyright by AEG Subject to change without notice
2223 208-32 06/05 Med forbehold om endringer

24

Der Kompressor läuft nach
einiger Zeit selbsttätig an.

Siehe Abschnitt „Reinigung
und Pflege“

Dies ist normal, es liegt keine
Störung vor.

Nach Änderung der Tem­peratureinstellung läuf der
Kompressor nicht sofort an.
Wasser am Kühlraumboden
oder auf Abstellflächen.

Tauwasser-Ablaufloch ist ver­stopft.

Lampe auswechseln

Warnung! Stromschlaggefahr! Vor dem Lampenwechsel Gerät abschalten
und den Netzstecker ziehen oder Sicherung abschalten bzw. herausdrehen.
Lampendaten: 220-240 V, Fassung: E 14

1. Zum Abschalten des Gerätes Tempera­turregler auf Stellung „0“ drehen.

2. Netzstecker ziehen.

3. Zum Auswechseln der Lampe
drücken die hintere Arretierung
gegen das Gehäuse bis die trasparen­te Abdeckung ausrastet..

4. Die Abdeckung in Pfeilrichtung abneh­men (siehe Abbildung).

5. Ersetzen durch eine neue Birne glei­cher Leistung (die maximale Leistung
ist am Leuchtkörper angegeben).

6. Lampenabdeckung wieder einsetzen.

7. Gerät wieder in Betrieb nehmen.

Starke Reifbildung im Gerät,
evtl. auch an der Türdichtung.

Türdichtung ist undicht (evtl.
nach Türanschlagwechsel).

An den undichten Stellen Tür­dichtung vorsichtig mit einem
Haartrockner erwärmen (nicht
wärmer als ca. 50 °C). Gleich­zeitig die erwärmte Türdich­tung von Hand so in Form
ziehen, daß sie wieder
einwandfrei anliegt.

Ungewöhnliche Geräusche.

Gerät hat Kontakt mit der
Wand oder mit anderen
Gegenständen.

Gerät steht nicht gerade.

Ein Teil, z. B. ein Rohr, an der
Geräterückseite berührt ein
anderes Geräteteil oder die
Wand.

Gegebenenfalls dieses Teil
vorsichtig wegbiegen.

Gerät etwas wegrücken.

Verstellfüße nachjustieren.

Störung Mögliche Ursache Abhilfe

49

Regulations, Standards, Guidelines

This appliance was designed for household use and was manufactured in
accordance with the appropriate standards. The necessary measures in
accordance with appliance safety legislation regulations (GSG), accident
prevention regulations for refrigeration appliances (VBG 20) and the regu­lations of the German Society of Electrical Engineers (VDE) were observed in
the manufacture of this appliance.

The refrigerant circuit has been checked for leaks.
This appliance is in accordance with the following EU guidelines:
– 73/23/EWG dated 19 February 1973 - low voltage guidelines.
– 89/336/EWG dated 3 May 1989
(including guideline change notice 92/31/EWG) - EMV guideline

Customer Service

If you cannot find the remedy for a malfunction in these operating instruc­tions, please contact your dealer or our customer service department.
Addresses and telephone numbers are listed in the accompanying booklet
"Guarantee Conditions/Customer Service Locations".

Selective ordering of replacement parts can save unnecessary travel and
costs. For this reason always provide the following appliance information:

This information can be found on the serial plate in the interior at the left
of the appliance.

• Model Name

• Model Number (PNC)

• Serial Number (S-No.)

We recommend that you enter this information here, so that it is handy if
needed.

Note: The customer bears the costs of unjustified customer service calls
even during the guarantee period.

25

Bestimmungen, Normen, Richtlinien

Das Kältegerät ist für den Haushalt bestimmt und wurde unter Beachtung
der für diese Geräte geltenden Normen hergestellt.

Bei der Fertigung wurden insbesondere die nach dem Gerätesicherheitsgesetz
(GSG), der Unfallverhütungsvorschrift für Kälteanlagen (VBG 20) und den
Bestimmungen des Verbandes Deutscher Elektrotechniker (VDE) notwendigen
Maßnahmen getroffen. Der Kältekreislauf wurde auf Dichtheit geprüft.

Dieses Gerät entspricht den folgenden EG-Richtlinien:
– 73/23/EWG vom 19.2.1973 - Niederspannungsrichtlinie
– 89/336/EWG vom 3.5.1989 (einschließlich Änderungsrichtlinie

92/31/EWG) - EMV-Richtlinie

48

Unusual noises.

The appliance is touching the
wall or other objects.

Appliance is not level.

A component, e.g. a pipe, on
the rear of the appliance is
touching another part of the
appliance or the wall.

The compressor starts after a
period of time.

See the "Cleaning and Care"
section.

This is normal, no error has
occurred.

The compressor does not start
immediately after changing
the temperature setting.
Water on the floor or on sto­rage shelves.

Water drain hole is blocked.

If necessary, carefully bend
the component out of the
way.

Move the appliance slightly.

Readjust the feet.

Changing the light bulb

Warning! There is a risk of electric shocks! Before changing the light bulb,

switch off the appliance and unplug it, or pull the fuse or the circuit breaker.
Light bulb data: 220-240 V

1. To switch off the appliance, turn the
temperature regulator to position
"0".

2. Unplug the mains plug.

3. To change the light bulb press on the
rear hook and at the same time slide
the cover in the direction indicated
by the arrow.

4. Change the defective light bulb
with one of the same power (the
maximum power is shown on the
light diffuser).

5. Refit the light bulb cover.

6. Put the refrigerator back into opera­tion.

Malfunction Possible Cause Remedy

26

Dear customer,

Before placing your new refrigerator/freezer into operation please read the­se operating instructions carefully. They contain important information for
safe use, for installation and for care of the appliance.

Please keep these operating instructions for future reference. Pass them on
to possible new owners of the appliance.

These operating instructions are for use with several technically comparable
models with varying accessories. Please observe the notes which apply to
your model.

Notes which are important for your safety or for the proper functioning of
the appliance are stressed with a warning triangle and/or with signal words
(Warning!, Caution!, Attention!). Please observe the following carefully.

Supplementary information regarding operation and practical applications
of the appliance appear after this symbol.

Tips and notes concerning economical and environmentally sound use of
the appliance are marked with the flower.

The operating instructions contain instructions for the correction of possi­ble malfunctions by the user in the section "What to do if ...". If these
instructions should not be sufficient, our customer service department is
always available to you.

Printed on paper manufactured with environmentally sound processes.

who thinks ecologically acts accordingly ...

47

What to do if ...

Correcting Malfunctions

A malfunction may be caused by only a minor fault that you can rectify
yourself using the following instructions. Do not perform any other work on
the appliance if the following information does not provide assistance in
your specific case.

Warning! Repairs to refrigerators/freezers may only be performed by
qualified service engineers. Improper repairs can give rise to significant
hazards for the user. If your appliance needs repairing, please contact your
specialist dealer or our Customer Service.

Malfunction Possible Cause Remedy

Appliance does not work.

Appliance is not switched on Switch on the appliance.
Mains plug is not plugged in

or is loose.

Insert mains plug.

Fuse has blown or is defective.

Check fuse, replace if neces­sary.

Socket is defective.

Mains malfunctions are to be
corrected by an electrician.

The food is too warm.

The appliance is near a heat
source.

Temperature is not properly
adjusted.

Please look in the "Initial Start
Up" section.

Turn the temperature regula­tor to a colder setting tempo­rarily.

Door was open for an exten­ded period.

Please look in the "Installation
location" section.

A large quantity of warm
food was placed in the
appliance within the last 24
hours.

Open the door only as long as
necessary.

Appliance cools too much. Temperature is set too cold.

Turn the temperature regula­tor to a warmer setting tem­porarily..

Interior lighting does not
work.

Light bulb is defective.

Please look in the "Changing
the Light Bulb" section.

Carefully warm the leaking
sections of the door seal with
a hair dryer (not hotter than
approx. 50 °C). At the same
time shape the warmed door
seal by hand such that it sits
correctly

Heavy build up of frost, possi­bly also on the door seal.

Door seal is not air tight (pos­sibly after changing over the
hinges).

27

Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Shelf holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Your refrigerator needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Rehingeing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Housing dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Instructions for total built-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Starting up and temperature regulation . . . . . . . . . . . . . . . . . . . . .37

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Starting up and temperature regulation of freezer compartment 39

Quick-freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Storage shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Variable Inner Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Moisture regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Variable Storage Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Fresh food refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Freezing and storing frozen food . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Ice pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Preparation of Ice Cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Freezing calender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

What to do if . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . .49

46

Energy Saving Tips

• Do not install the appliance near cookers, radiators or other sources of

warmth. High ambient temperatures cause longer, more frequent opera­tion of the compressor.

• Ensure sufficient air circulation and exhaust at the appliance base and at

the back wall of the appliance. Never cover air vent openings.

• Do not place warm foods into the appliance. Allow warm foods to cool

first.

• Only leave door open as long as necessary.

• Do not set temperature any colder than necessary.

• Put frozen food in the fridge to defrost. The cold in the frozen food will

then be used to cool the fridge.

• Keep the heat emitting condenser, the metall grille on the rear wall of

your appliance, always clean.

2. Defrost the freezer compartment prior to cleaning (see "Defrosting" sec­tion).

3. Switch the appliance off and remove the plug from the mains, or switch off
or turn out the circuit breaker or fuse.

4. Clean the appliance and the interior accessories with a cloth and lukewarm
water. Commercially available dish washing detergents may also be used.

5. After cleaning wipe with fresh water and rub dry.
Accumulation of dust at the condenser increases energy consumption. For

this reason carefully clean the condenser at the back of the appliance once
a year with a soft brush or a vacuum cleaner.

6. Check the water drain hole on the rear wall of the fridge. Clear a blocked
drain hole with the aid of the green peg in the pack of accessories included
with the appliance.

7. After everything is dry place appliance back into service.