AEG-Electrolux ERP1672, SK81840-6I, SK81840-5I User Manual

Page 1
GEBRAUCHSANWEISUNGEN
INSTRUCTION BOOKLET
2222 749-75
ERP 1672
Kühlschrank / refrigerator
GB
D
Page 2
Safety Instructions
t
Please read these operating instructions carefully before installing the appliance. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. If you are unsure about the meaning of these warnings contact the Customer Care Department.
Domestic Use
¥ The domestic refrigerators and freezers are
designed to be used specifically for the storage of edible foodstuffs only.
¥ Check the appliance for transport damage. Under
no circumstances should a damaged appliance be installed. In the event of damage please contact your retailer.
¥ This appliance is heavy. The edges and projecting
parts of the cabinet may be sharp. Be careful when moving the cabinet and always use gloves.
¥ Any electrical work required to install this appliance
should be carried out by a qualified electrician or competent person.
¥ Ensure that the appliance does not stand on the
electrical supply cable.
¥ Do not use electrical appliances inside the
appliance
¥ Do not keep carbonated drinks or bottles in the freezer
compartment. The glass bottles may break.
¥ Ice lollies can cause Ôfrost/freezer burnsÕ if
consumed straight from the freezer.
¥ It is dangerous to try and alter the specifications or
modify this product in any way.
¥ Under no circumstances should you attempt to
repair the appliance yourself. Refer to your local Service Centre, and always insist on genuine spare parts.
Child Safety
¥ This appliance is designed to be operated by
adults only. There is a risk of suffocation! Keep packaging material away from children!
¥ In case of disposal of the appliance, cut off the
supply cable as close as possible and make thelock unusable, to prevent children from closing themselves inside the appliances.
Environment Protection
¥ This appliance does not contain gasses which
could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from your municipal authorities.
¥ The materials used on this appliance marked with
the symbol are recyclable.
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Use and Control
Before Use / Refrigerator compartment - Starting the appliance . . . . . . . . . . . . . . . . . . . . .12
Temperature control / Internal parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Maintenance Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cleaning / Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Something not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Customer Service and Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Installation
Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Door reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Building-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Index
Page 3
12
These symbols guide you in the reading of these instructions for use:
Notes which are important for your safety or for the proper functioning of the appliance
Supplementary information regarding operation and practical applications of the appliance.
Tips and notes concerning economical and environmentally sound use of the appliance.
Use and Control
Before Use
Wait two hours before connecting the appliance to allow the oil to flow back in the compressor.
¥ Before using the appliance for the first time, wash
the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly.
Do not use detergents or abrasive powders, as these will damage the finish.
¥ Remove safety elements used for transportation.
Refrigerator compartment Starting the appliance
¥ Insert the plug into the wall socket and turn the
thermostat knob clockwise beyond position ÇOÈ (OFF).
¥ Turn the thermostat control to the required setting.
¥ To remove the internal shelf pull forward until it can
be tipped up or down and removed.
¥ Please do the same in reverse to insert the shelf at
a different height.
The glass shelf above the vegetable drawers and the bottle shelf should always remain in position, to ensure correct air circulation.
¥ To permit storage of food packages of various
sizes, the central door shelf can be adjusted in height.
¥ Gradually pull the shelf in the direction of the
arrows until it comes free, then reposition as required.
¥ For more thorough cleaning, the top and bottom
door sheves can be removed by pulling them in the direction of the arrows, then refitting them in position.
Internal Parts
Storage shelves
¥ The shelves can be removed for cleaning. ¥ To permit storage of food packages of various
sizes, the shelves can be placed at different heights.
D338
Page 4
13
Hints
Saving Energy
¥ Pay careful attention to where the cabinet is
placed. See the section ÒInstallationÓ. When installed correctly the cabinet will consume less energy.
¥ Try to avoid keeping the doors open for long
periods or opening the doors too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often.
¥ If the ambient temperature is high, the thermostat
knob is on the coldest setting (higher numbers) and the appliance is fully loaded, the compressor may run continuously, causing frost or ice to form on the evaporator. If this happens, turn the knob to a warmer setting (lower numbers) to allow automatic defrosting and so a saving in electricity consumption.
¥ Do not place warm foods inside the appliance.
Allow warm foods to cool first.
¥ Keep the heat emitting condenser, the metall grille
on the rear wall of your appliance, always clean.
Hints for refrigeration
¥ Do not store warm food or evaporating liquids in
the refrigerator and do cover or wrap up the food, particularly if it has a strong smell.
To help you use your refrigerator correctly, here are some useful hints:
¥
Raw meat (beef, pork, lamb & poultry): wrap in polythene bags and place on top of the salad compartment, this being the coldest spot in the refrigerator.
Meat can only be stored safely in this way for one or two days at the most.
¥ Cooked food, cold cuts, jelly, etc.: these should
be well covered and can be stored on any of the glass shelves.
¥
Fruit & vegetables: these should be thoroughly cleaned and placed in the bottom drawer.
¥ Butter & cheese: these should be placed in
special airtight containers or wrapped in aluminium foil or polythene bags to keep out as much air as possible.
¥
Milk bottles: these should have a top and should be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.
Maintenance
Unplug the appliance before carrying out any maintenance operation.
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must therefore only be carried out by authorised technicians.
Defrosting
Refrigerator compartment
¥ Defrosting the refrigerator compartment is
automatic. The defrost water drains out through a trough into a container at the back of the appliance, above the motor compressor, where it evaporates.
¥ It is important to periodically clean the defrost
water drain hole.
D037
Page 5
14
Cleaning
Never use metal objects for cleaning your appliance as it may get damaged.
NEVER use detergents, abrasive powders, highly perfumed cleaning products or wax polishes to clean the interior as these will damage the surface and leave a strong odour.
Clean the inside with warm water and bicarbonate of soda. Rinse and dry thoroughly.
To guarantee a safe operation of the fridge, once a year remove the ventilation grille at the base and clean the air channels with a vacuum cleaner.
When the appliance is not in use
Disconnect the appliance from the electricity supply. Empty all foods and clean the appliance, leaving the doors ajar to prevent unpleasant smells.
Changing the light bulb
¥ Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity supply, then replace the bulb as follows:
1. unscrew the light cover securing screws.
2. unhook the moving part by pressing it as shown in the figure.
3. Replace the bulb by other with another with the same charcteristics.
Something not Working
Problems may be due to causes which can easily be solved before calling the Technical Service. Please follow these instructions:
Level properly the appliances if it is not well levelled. Weight surpasses the storage limit of the door shelf so spread weight more evenly or take some products out. Readjust the door if it is not properly aligned.
Set a lower temperature. Distribute the food products to allow cold air to circulate around them. Make sure that the door is completely closed and that the insulating strip is complete and clean. The temperature where the cabinet is placed is above normal room temperature.
Set a warmer temperature.
Turn the thermostat knob to a lower number The temperature where the cabinet is placed is above normal room temperature. Check that the ventilation is sufficient and that the ventilation openings are unobstructed. The cause could be the introduction of large quantities of food and/or frequent opening/closing of the door.
Sometimes is normal. During automatic defrosting frost thaws on the cooling plate.
Place the drain hose at the back of the cabinet above the drain bowl.
Sometimes this is normal. Temperature control may cause clicking sounds when the system is connected or disconnected. The injected cooling gas may produce a gurgling sound while passing through the tubes. The motor may cause a humming noise and/or slight bumping. The insulation material used has a tendency to slighly increase noise levels, how ever it allows for much better insulation and a lower energy consumption, You may occasionally hear the fans working. This is nothing to worry about. The fans are simply helping the air to circulate more effectively.
Door do not close
It is too warm inside the refrigerator
It is too cold inside the refrigerator.
The compressor works continuously.
There is water inside/outside the refrigerator.
Water comes out on the floor.
Noises
SYMPTOM SOLUTION
D411
Page 6
Customer service and spare parts
This information can be found on the rating plate inside the cabenit on the left hand wall. We recommend that you enter this information here, so that it is handy if needed.
If you cannot find the remedy for a malfunction in these operating instructions, please contact your dealer or our customer service department and consult the Guarantee card.
Selective ordering of replacement parts can save unnecessary travel and costs.
For this reason always provide the following appliance information:
- Model Name
- Model Number (PNC)
- Serial Number (S-No.)
Technical specifications
The technical data is indicated in the rating plate on the left side inside the appliance.
Installation
Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages.
¥ During normal operation, the condenser and
compressor at the back of the appliance heat up considerably. Always ensure that there is adequate ventilation as a failure to do this will result in component failure and possible food loss. See installation instructions.
¥
Important: if the supply cord is damaged, it must be replaced by a special cord or assembly availa­ble from the manufacturer or its service agent.
Positioning
¥ Unpack the cabinet and check that it is in good
condition and free of any transport damage.
¥ Place the refrigerator away from direct sunlight and
heat sources.
¥ Maintain recommended ventilation.
It is necessary that the niche is provided with a conduct of venti-lation having the following dimensions:
Depth 50 mm Width 540 mm
15
The climate classification can be found on the rating plate, which is located inside the cabinet on the left hand wall.
The following table shows which ambient temperature is correct for each climate classification:
Climate classification
SN +10 to +32¡C
+16 to +32¡C
+18 to +38¡C
+18 to +43¡C
N
ST
T
for an ambient temperature of
When the ambient temperature is not included within the range indicated for the class of this appliance, the storage temperature in the appliance cannot be guaranteed; therefore it is advisable to use the food stored as soon as possible.
Page 7
16
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used.
Important The appliance must be earthed.
The power supply cable plug is provided with a contact for this purpose.
If the domestic power supply socket is not earthed. connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician.
The Manufacturer declines all responsibility if the above safety precautions are not observed.
Door reversal
This appliance complies with the following E.E.C. Directives:
- 87/308 EEC of 2/6/87 relative to radio interference suppression.
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications.
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
Attention!
It must be possible to disconnect the appliance
from the mains power supply; the plug must therefore be easily accessible after installation.
Warning!
If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier.
Proceed as follows:
1 2
3
TAW1MERA
TAW2MERA
TAW3MERA
Page 8
17
Building-in
Aligning the furniture housing
Detaching the appliance door
Dimensions of the recess The following installation steps are illustrated only
when the door is hinged on the left, please carry out the following installation steps on the opposite side as appropriate.
2. Cut joint cover fillets (E)
1. Performing adjustments
3. Apply joint cover fillets (E).
FAL1MERA
100
MAU2ME
90°
90°
FAL2MERA
1BL80R
FAL3MERA
Page 9
GF1MERA
4. Fit ventilation grill (N) and push appliance into
place
5. Screw the appliance into place.
PL09
6. Install screw-head caps (L)
7. Attach door panel.
PL12
8. Apply door handle.
9. Inserting the appliance door.
TE1MERA
GAU4ME
10. Aligning the appliance door (where necessary).
18
PL13
SAB1ME
Page 10
ELECTROLUX HOME PRODUCTS OPERATIONS EUROPE
923 632 667
Loading...