AEG-Electrolux SK25510 User Manual

Page 1
Kühl - Gefrierschrank / refrigerateur - congelateur
fridge - freezer / frigorifero - congelatore
GEBRAUCHSANWEISUNGEN
MODE D’EMPLOI
LIBRETTO ISTRUZIONI
INSTRUCTION BOOK
2223 439-01
I
F
D
GB
Page 2
26
WARNINGS
It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings.
If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child.
These warnings are provided in the interest of safety.You must read them carefully before installing or using the appliance.
General Safety
• This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product.
• It is dangerous to alter the specifications or modify this product in any way.
• Before any cleaning or maintenance work is carried out, be sure to switch off and unplug the appliance.
• This appliance is heavy. Care should be taken when moving it
• Ice lollies can cause frost burns if consumed straight from the appliance.
Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages.
The appliance must not be located close to radiators or gas cookers.
Avoid prolonged exposure of the appliance to direct sunlight.
There must be adequate ventilation round the back of the appliance and any damage to the refrigerant circuit must be avoided.
For freezers only (except built-in models): an ideal location is the cellar or basement.
Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances.
Service/Repair
• Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person
• This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used.
• Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning. Refer to your local
Service Centre, and always insist on genuine spare parts.
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.
Use
The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only.
Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN).The class of your appliance is shown on its rating plate.
Warning: when the ambient temperature is not included within the range indicated for the class of this appliance, the following instructions must be observed: when the ambient temperature drops below the minimum level, the storage temperature in the freezer compartment cannot be guaranteed; therefore it is advisable to use the food stored as soon as possible.
Frozen food must not be re-frozen once it has been thawed out.
Manufacturers’ storage recommendations should be strictly adhered to. Refer to relevant instructions.
The inner lining of the appliance consists of channels through which the refrigerant passes. If these should be punctured this would damage the appliance beyond repair and cause food loss. DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Frost may be removed by using a plastic scraper. Under no circumstances should solid ice be forced off the liner. Solid ice should be allowed to thaw when defrosting the appliance.
Page 3
27
CONTENTS
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Use / Cleaning the interior - Operation - Temperature regulation - Fresh food refrigeration - Freezing . .
fresh food - Storage of frozen food - Thawing - Ice-cube production . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Use / Movable shelves -Positioning the door shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Hints / Hints for refrigeration - Hints for freezing - Hints for storage of frozen food . . . . . . . . . . . . . . . . .30
Maintenance / Periodic cleaning - Periods of non-operation - Interior light - Defrosting . . . . . . . . . . . . .31
Customer service and spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Installation - Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Installation/ Electrical connection - Rear spacers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Installation/ Door Reversibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Installation/ Inner door reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. Never use metal objects for cleaning your appliance as it may get damaged.
Installation
• During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the instructions.
Attention: keep ventilation openings clear of obstruction.
• Care must be taken to ensure that the appliance does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must be replaced by a special cord or assembly availa­ble from the manufacturer or its service agent.
• If the appliance is transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit. It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor.
• There are working parts in this product which heat up. Always ensure that there is adequate ventilation as a failure to do this will result in component failure and possible food loss. See installation instructions.
• Parts which heat up should not be exposed. Wherever possible the back of the product should be against a wall.
Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials.The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from municipal authorities.The materials used on this appliance marked by the symbol are recyclable.
Disposal of old Appliances
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Page 4
28
Fresh food refrigeration
To obtain the best performance:
do not store warm food or evaporating liquids in the refrigerator;
do cover or wrap the food, particularly if it has a strong flavour.
Position food so that air can circulate freely round it.
Cleaning the interior
Before using the appliance for the first time, wash the interior and all internal accessories with luke­warm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly.
Do not use detergents or abrasive
powders, as these will damage the finish.
Temperature regulation
The temperature is automatically regulated and can be increased to achieve a higher temperature (warmer) by rotating the thermostat knob toward lower settings or reduced (colder) rotating the knob towards higher settings.
However, the exact setting should be chosen keeping in mind that the temperature inside the refrigerator depends on:
room temperature;
how often the door is opened;
the quantity of food stored;
location of appliance.
A medium setting is generally the most suitable.
Important
If the ambient temperature is high or the appliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall. In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption.
USE
Operation
Insert the plug into the wall socket. Turn the thermostat knob ,clockwise, beyond the “O”
(STOP) position. To stop operation, simply turn the thermostat knob to
position “O”.
Freezing fresh food
The 4-star compartment is suitable for long term storage of commercially frozen food, and for freezing fresh food.
To freeze fresh foods It is not necessary to change the setting of the thermostatknob. However, for a quicker freezing operation, turn the thermostat knob to the coldest setting; but remeber that, in this condition, the refrigerator compartment temperature might drop below 0°C. If this occurs reset thermostat knob to a warmer setting.
Ice-cube production
This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment.
Do not use metallic instruments to remove the trays from the freezer.
Thawing
Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation.
Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer.
Storage of frozen food
When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least two hours on the coldest setting, then turn the thermostat knob to the normal operating position.
Important
In the event of accidental defrosting, for example due to a power failure, if the power has been off for longer that the value shown in the technical characteristics chart under “rising time”, the defrosted food must be consumed quickly or cooked immediately and then refrozen (after cooling).
Page 5
29
Positioning the door shelves
To permit storage of food packages of various sizes, the door shelves can be placed at different heights.
To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.
Movable shelves
The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.
D338
Page 6
30
HINTS
Hints for refrigeration
Useful hints: Meat (all types): wrap in polythene bags and place
on the glass shelf above the vegetable drawer.
For safety, store in this way only one or two days at the most.
Cooked foods, cold dishes, etc..: these should be
covered and may be placed on any shelf. Fruit and vegetables: these should be thoroughly
cleaned and placed in the special drawer(s) provided.
Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.
Hints for freezing
To help you make the most of the freezing process, here are some important hints:
the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate;
the freezing process takes 24 hours. No further food to be frozen should be added during this period;
only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
wrap up the food in aluminium foil or polythene and make sure that the packages are airtight;
do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter;
lean foods store better and longer than fatty ones; salt reduces the storage life of food;
water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt;
it is advisable to show the freezing-in date on each individual pack to enable you to keep tab of the storage time;
do not put carbonated liquids (fizzy drinks, etc.) in the freezer compartment as they may burst.
Hints for storage of frozen food
To obtain the best performance from this appliance, you should:
make sure that the commercially frozen foodstuffs were adequately stored by the retailer;
be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the shortest possible time;
not open the door frequently or leave it open longer than absolutely necessary.
Once defrosted, food deteriorates rapidly and cannot be refrozen.
Do not exceed the storage period indicated by the food manufacturer.
Page 7
31
Defrosting
Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.
It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside. Use the special cleaner provided, which you will find already inserted into the drain hole.
The freezer compartment, however, will become progressively covered with frost. This should be removed with a plastic scraper, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs.
Never use sharp metal tools to scrape off frost from the evaporator as you could damage it.
MAINTENANCE
Unplug the appliance before carrying out
any maintenance operation. Warning
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.
Periodic cleaning
Clean the inside with warm water and bicarbonate of soda.
Rinse and dry thoroughly. Clean the condenser (black grill) and the
compressor at the back of the appliance with a brush or a vacuum cleaner.This operation will improve the performance of the appliance and save electricity consumption.
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the plastics used in this appliance. For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing-up liquid added.
Periods of non-operation
When the appliance is not in use for long periods, take the following precautions:
remove the plug from the wall socket; remove all food; defrost and clean the interior and all accessories; leave the door ajar to allow air to circulate to prevent
unpleasant smells.
Interior light
The light bulb inside the refrigerator compartment can be reached as follows:
unscrew the light cover securing screw.
unhook the moving part as shown in the figure.
If the light does not come on when the door
is open, check that it is screwed into place properly. If it still does not light up, change the bulb.The rating is shown on the light bulb cover.
D411
D037
Page 8
32
CUSTOMER SERVICE AND SPARE PARTS
If the appliance is not functioning properly, check that:
the plug is firmly in the wall socket and the mains power switch is on;
there is an electricity supply (find out by plugging in another appliance);
the thermostat knob is in the correct position.
If there are water drops on the bottom of the cabinet, check that the defrost water drain
opening is not obstructed (see “Defrosting” section).
If your appliance is still not working properly after making the above checks, contact the nearest service centre.
To obtain fast service, it is essential that when you apply for it you specify the model and serial number of your appliance which can be found on the guarantee certificate or on the rating plate located inside the appliance, on the bottom left-hand side.
However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows:
1. pull out the plug from the wall socket or turn the thermostat knob to the «O» setting;
2. remove any stored food, wrap it in several layers of newspaper and put it in a cool place;
3. leave the door open, place a basin on the top shelf of the refrigerator compartment, under the drain hole, remove the plug as shown in the figure;
4. when defrosting is completed, dry the interior thoroughly and refit the plug;
5. turn the thermostat knob back to the required setting or replace the plug in the power socket.
6. After two or three hours, reload the previously removed food into the compartment.
Important:
Never use sharp metal tools to scrape off frost from the evaporator as you could damage it.
Do not use a maechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer.
A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life.
PR151
Page 9
33
INSTALLATION
Location
The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc.
For safety reasons, minimum ventilation must be as shown in Fig.
Appliance positioned under overhanging kitchen wall units (see Fig. A).
Appliance positioned without overhanging kitchen wall units (see Fig. B).
Attention: keep ventilation openings clear of obstruction.
Two adjustable feet at the cabinet base allow accurate levelling of the appliance.
Attention
It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation.
100 mm10 mm
A
NP006
B
10 mm
Page 10
34
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized auto-transformer must be used.
The appliance must be earthed.
The power supply cable plug is provided with a contact for this purpose.
If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician.
The Manufacturer declines all responsibility if the above safety precautions are not observed.
This appliance complies with the following E.E.C. Directives:
- 87/308 EEC of 2/6/87 relative to radio interference suppression.
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
Rear spacers
In the bag with the documentation, there are two spacers which must be fitted in the two top corners.
Slacken the screws and insert the spacer under the screw head, then re-tighten the screws.
PR153
Page 11
35
Door reversibility
Before carrying out any operations, remove the plug from the power socket.
To change the opening direction of the door, proceed as follows:
To carry out the following operations, we suggest that this be made with another person that will keep a firm hold on the doors of the appliance during the operations.
Open the door with the appliance in the upright position. Unscrew the screws and remove the door plastic trim.
Remove the little plastic cover from the door plastic trim and refit on the opposite side (d).
Lay down the appliance back side down.
Remove the plastic hinge covers dx and sx (3).
Unscrew the upper hinge and remove it (1-2)
Unscrew the screw and remove the door stopper (4).
Remove the door
Remove the ventilation grill (D).
Using a 10 mm spanner, unscrew the hinge pin (E) and reassemble it on the opposite side of the hinge;
Screw down the bottom hinge (E) on the opposite side by using the screws previously removed.
Remove the plug (F) from the ventilation grill (D) and replace it on the opposite side.
Re-assemble the ventilation grill (D).
Reinsert the door .
Pay attention that the front board of the doors are parallel to the front board of the top.
Fix the door stopper on the opposite side (4).
Position and fix the upper hinge on the opposite side (1-2)
Reinsert the 2 plastic hinge covers (3).
Lift up the appliance to vertical position.
Open the door and reposition the upper door plastic trim with screws.
Fix the handles on the opposite side, insert the plastic plugs into the holes left open that can be found in the instruction for use bag.
3
2
1
4
E
F
D
F
E
F
F
Page 12
36
Reposition, level the appliance, wait for at least two hours and then connect it to the power socket. In any case you do not want to carry out the above mentioned operations, contact the nearest After Sales Service Force. The After Sales Service specialist will carry out the reversibility of the doors at your cost.
Warning After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier.
Inner door reversal
180°
Page 13
47
KUNDENDIENST
Servicestellen Points de service Servizio dopo vendita
5506 Mägenwil/Zürich Industriestr. 10
9000 St. Gallen Zürcherstrasse 204 e
4127 Birsfelden Hauptstrasse 52
6032 Emmen Buholzstrasse 1
7000 Chur Comercialstrasse 19
3018 Bern Morgenstrasse 131
Ersatzteilverkauf Point de vente de
5506 Mägenwil Industriestrasse 10 Tel. 0848 848 023
Fachberatung / Verkauf Demonstration / Vente Consulente (cucina) /
8048 Zürich Badenerstrasse 587 Tel. 044 405 81 11
Garantie Garantie Garanzia
Für jedes Produkt gewähren wir ab Verkauf bzw. Lieferdatum an den Endverbraucher eine Garantie von 2 Jahren. (Ausweis durch Garantie­schein, Faktura oder Verkaufs­beleg). Die Garantieleistung umfasst die Kosten für Material, Arbeits- und Reisezeit.
Die Garantieleistung entfällt bei Nichtbeachtung der Gebrauchs­anweisung und Betriebsvorschriften, unsachgerechter Installation, sowie bei Beschädigung durch äussere Einflüsse, höhere Gewalt, Eingriffe Dritter und Verwendung von Nicht­Original Teilen.
1028 Préverenges Le Trési 6
rechange
5506 Mägenwil Industriestrasse 10 Tel. 0848 848 023
8048 Zürich Badenerstrasse 587 Tel. 044 405 81 11
Nous octroyons sur chaque produit 2 ans de garantie à partir de la date de livraison ou de la mise en service au consommateur (documenté au moyen d’une facture, d’un bon de garantie ou d’un justificatif d’achat). Notre garantie couvre les frais de mains d’œuvres et de déplacement, ainsi que les pièces de rechange.
Les conditions de garantie ne sont pas valables en cas d’intervention d’un tiers non autorisé, de l’emploi de pièces de rechange non originales, d’erreurs de maniement ou d’installation dues à l’inobser­vation du mode d’emploi, et pour des dommages causés par des influences extérieures ou de force majeure.
6916 Grancia Zona Industriale E
Vendita pezzi di ricambio
5506 Mägenwil Industriestrasse 10 Tel. 0848 848 023
Vendita
8048 Zürich Badenerstrasse 587 Tel. 044 405 81 11
Per ogni prodotto concediamo una garanzia di 2 anni a partire dalla data di consegna o dalla sua messa in funzione. (fa stato la data della fattura, del certificato di garanzia o dello scontrino d’acquisto ) Nella garanzia sono comprese le spese di manodopera, di viaggio e del materiale.
Dalla copertura sono esclusi il logoramento ed i danni causati da agenti esterni, intervento di terzi, utilizzo di ricambi non originali o dalla inosservanza delle prescrizioni d’istallazione ed istruzioni per l’uso.
Page 14
www.electrolux.com
www.electrolux.ch
Loading...