AEG-Electrolux PLEW30S3CC User Manual

Wa r m & Ser v e

Drawer

CONTENTS Page

Product Registration ....................................................... 2

Important Safety Instructions .....................................3-4

Before Setting Warmer

Drawer Control ................................................................ 4

Setting Warmer Drawer Control ...................................... 5

General Cleaning ..........................................................6-7

Avoid Service Checklist ................................................... 8

Installation Instructions ........................................... 9-11

Warranty ........................................................................ 12

Español ................................................................... 13-24

Français ................................................................... 25-36

318201001 (0111) Rev. C

English - pages 1-12 Español - Paginás 13-24 Français - pages 25-36

Product Registration

The self-addressed PRODUCT REGISTRATION CARD should be filled in

completely, signed and returned to Electrolux Home Products North America.

Thank you for choosing this appliance. The information contained within this Owner's Guide will instruct you on how to properly install, operate and care for

your appliance. Please read through the information contained in your literature pack to learn more about your new appliance.

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers found on the right side of the drawer frame.

Model Number: __________________________________________________

Serial Number: __________________________________________________

Date of Purchase: ________________________________________________

This Owner's Guide contains general operating instructions for your appliance and feature information for several models. Your range may not have all the described features. The graphics shown are representational. The graphics on your range may not look exactly like those shown.

Note: The instructions appearing in this Owner's Guide are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Important: Keep a copy of your bill of sale. The date on the bill establishes the warranty period service be required. Place it where it can be easily retrieved. If service is performed while the appliance is under warranty, you may have to show your bill of sale.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance.

Save these instructions for future reference.

This guide contains important safety symbols and instructions. Please pay special attention to these symbols and follow all instructions given. Here is a brief explanation of the use of these symbols.

This symbol will help alert you to situations that

may cause serious bodily harm, death or property damage.

• Remove all tape and packaging wrap before using the warmer drawer. Destroy the carton and plastic bags after unpacking the appliance. Never allow children to

play with packaging material.

• Proper Installation—Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/ NFPA No. 70—latest edition in the U.S. A., or CSA C22.1, Part 1 in Canada, and local code requirements.

Install only per installation instructions provided in this manual.

Ask your dealer to recommend a qualified technician and an authorized repair service. Know how to disconnect the electrical power to the drawer at the circuit breaker or fuse box in case of an emergency.

• User Servicing—Do not repair or replace any part of the appliance unless specifically recommended in the manuals. All other servicing should be done only by a

qualified technician to reduce the risk of personal injury and damage to the appliance.

• Never modify or alter the construction of a drawer by removing panels, wire covers, locking plates, or any other part of the product.

TO REDUCE THE

• ALL WARMER DRAWERS CAN TIP.

• INJURY TO PERSONS COULD RESULT.

• INSTALL ANTI-TIP DEVICE PACKED WITH WARMER DRAWER.

• SEE INSTALLATION INSTRUCTIONS.

RISK OF TIPPING OF THE WARMER DRAWER, THE DRAWER MUST BE SECURED BY PROPERLY INSTALLED ANTI-TIP LOCKING PLATES PROVIDED WITH THE DRAWER. TO CHECK IF THE LOCKING PLATES ARE INSTALLED PROPERLY, GRASP THE HANDLE OF THE OPEN DRAWER AND SEE IF THE DRAWER WILL SLIDE OUT OF THE OPENING. REFER TO THE INSTALLATION INSTRUCTIONS FOR PROPER LOCKING PLATE INSTALLATION.

This symbol will help alert you to situations

that may cause bodily injury or property damage.

Stepping, leaning or sitting on the door or drawer can result in serious injuries and may also cause damage to the warmer drawer. Do not allow children to

climb or play around the drawer. An open drawer, when hot, may cause burns.

• Storage in or on Appliance—Flammable materials

should not be stored in the drawer. This includes paper,

plastic and cloth items, such as cookbooks, plasticware and towels, as well as flammable liquids. Do not store explosives, such as aerosol cans, on or near the warmer drawer. Flammable materials may explode and result in fire or property damage.

• Do not leave children alone. Children should not be

left alone or unattended in the area where an appliance is in use. They should never be allowed to sit or

stand on any part of the appliance.

• DO NOT TOUCH INTERIOR SURFACES OF THE WARMER

DRAWER. Surfaces may be hot even though they are dark

in color. During and after use, do not touch, or let clothing or other flammable materials touch these areas until they have had sufficient time to cool.

• Wear Proper Apparel—Loose-fitting or hanging

garments should never be worn while using the appliance. Do not let clothing or other flammable materials

contact hot surfaces.

• Use Only Dry Potholders—Moist or damp potholders

on hot surfaces may result in burns from steam. Do not

let the potholders touch hot heating elements. Do not use a towel or other bulky cloth instead of a potholder.

• Do Not Heat Unopened Food Containers—Build-up of

pressure may cause the container to burst and result in injury.

• IMPORTANT—Do not attempt to operate the warmer

drawer during a power failure. If the power fails, always turn the control off. If the drawer is not turned off

and the power resumes, the drawer may begin to operate again. Food left unattended could spoil.

Never use your appliance for warming or heating the room.

Do not use the warmer drawer for storage.

IMPORTANT SAFETY INSTRUCTIONS (continued)

IMPORTANT INSTRUCTIONS FOR USING YOUR WARM & SERVE DRAWER

• Protective Liners—Do not use aluminum foil to line warmer

drawer. Any other use of protective liners or aluminum foil may result in poor performance or damage to the appliance. Only use aluminum foil as recommended for baking if used as a cover placed on the food.

• Glazed Cooking Utensils—Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed utensils are suitable for use without breaking due to the sudden change in temperature. Check the manufacturer's recommendations.

• Use Care When Opening Warmer Drawer—Stand to the side of the unit when opening the door of a hot drawer. Let hot air or steam escape before you remove or replace food in the warmer drawer.

• Placement of Warmer Drawer Racks—Always place rack in desired location while drawer is cool. If rack must be moved while hot, use extreme caution. Use potholders and grasp the rack with both hands to reposition. Do not let potholders contact the hot element or interior of the warmer drawer. Remove all utensils from the rack before removing rack.

IMPORTANT INSTRUCTIONS FOR CLEANING YOUR WARM & SERVE DRAWER

• Clean the drawer regularly to keep all parts free of grease that could catch fire. Do not allow grease to

accumulate. Greasy deposits could catch fire.

• Kitchen cleaners/aerosols—Always follow the manufacturer's recommended directions for use. Be aware that excess residue from cleaners and aerosols may ignite causing damage and/or injury.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

SAVE THESE INSTRUCTIONS

Before Setting Warmer Drawer Control

Arranging Warmer Drawer Rack Positions

Set the warmer drawer rack in the vertical position as shown below.

The rack can be used in 2 ways:

• In the upright position to allow low profile food items to be placed both under and on top of the rack (for example, rolls or biscuits on top of the rack and a casserole dish under).

• In the downward position to allow you to place light weight food items and empty dishware (for example, rolls or pastries and dinner plates).

Downward PositionUpright Position

Setting Warmer Drawer Control

Use the warmer drawer to keep hot foods hot such as: vegetables, gravies, meats, casseroles, biscuits and rolls, pastries and heated dinner plates.

The warmer drawer is equipped with a catch which may require extra force when opening and closing the drawer.

To Operate the Warmer Drawer

The purpose of the warmer drawer is to keep hot cooked foods at serving temperature. Always start with hot food. It is not recommended to heat cold food in the warmer drawer.

All food placed in the warmer drawer should be covered with a lid or aluminum foil to maintain moisture and softness. Do not cover crisp foods. Do not use plastic

wrap to cover food. Plastic may melt onto the drawer and be very difficult to clean.

Use only dishware, utensils and cookware recommended for oven use in the warmer drawer.

Note: The knob shown below is typical only.

Warmer Drawer Recommended

Food Settings Chart

Food Item Setting

Always use potholders or oven mitts when removing food from the

warmer drawer as cookware and plates will be hot.

Indicator Light

The indicator light is located above the thermostat control knob. It turns on when the control is set, and stays on until the control is turned off. Make sure indicator light is off when removing food from drawer.

To Set the Thermostat Control

The thermostat control knob is used to select the temperature of the warmer drawer. It is located at the right side of the warmer drawer in the open position. The temperatures are approximate, and are designated by HI, MED and LO. The control can be set to the three settings, or anywhere between.

1. To set the thermostat, push in and turn the knob to the desired setting.

2. For best results, preheat the drawer before adding food. An empty drawer will

reach the LO setting in about 12 minutes, the MED setting in about 15 minutes, and the HI setting in about 18 minutes.

3. When done, turn the thermostat control to OFF.

Temperature Selection

Refer to the chart in the side column for recommended settings. If a particular food is not listed, start with the medium setting. If more crispness is desired, remove the lid or aluminum foil.

Bacon HI Biscuits MED Casseroles MED Eggs MED Empty Dinner Plates LO Fish, Seafood MED Fried Foods HI Gravies, creams, sauces MED Ham MED Hamburger Patties HI Pancakes, Waffles HI Pastries MED Pies MED Pizza HI Pork Chops HI Potatoes (baked) HI Potatoes (mashed) MED Poultry HI Roasts (Beef, Pork, Lamb) MED Rolls, soft LO Rolls, hard MED Vegetables MED

Most foods can be kept at serving temperatures by using the medium setting.

When a combination of foods are to be kept warm (for instance, a meat with 2 vegetables and rolls), use the high setting.

Refrain from opening the warmer drawer while in use to eliminate loss of heat from the drawer. Open only for adding or removing food.

To Warm Serving Bowls and Plates

Heat bowls and plates on the LO setting. Place empty dishes on the rack to raise them off drawer bottom. To further heat dishes or to heat fine china, check with the manufacturer for maximum heat tolerance.

General Cleaning

Cleaning Various Parts of Your Appliance

Before cleaning any part of the drawer, be sure control is turned OFF and the drawer is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANINGS WILL REDUCE THE NUMBER OF MAJOR CLEANINGS LATER.

Surfaces Vinyl

Plastic

Control Knobs, Control Panel

Stainless Steel

Door

Porcelain Enamel

Door Liner, Body Parts and Drawer Cavity

Warmer Drawer Rack

How to Clean

Use hot, soapy water and a cloth. Dry with a clean cloth.

To remove control knob, turn to the OFF position; grasp firmly and pull straight off the shaft. Clean with a cloth soaked in soapy water. Rinse with a clean water and a dishcloth. Be sure to squeeze excess water from the cloth before wiping the panel; especially when wiping around the controls. Excess water in or around the controls may cause damage to the appliance. To replace knob after cleaning, line up the flat sides of both the knob and the shaft; then push the knob into place.

Cleaners made especially for stainless steel are recommended. Always follow the manufacturer's instructions. Be sure to rinse the cleaners. DO NOT clean the door gasket. The door gasket is essential for a good seal. Care should be taken not to rub, damage or remove the gasket.

Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of clear water and ammonia. If necessary, cover difficult spots with an ammonia-soaked paper towel for 30 to 40 minutes. Rinse with clean water and a damp cloth, and then scrub with a soap-filled scouring pad. Rinse and wipe dry with a clean cloth. Remove all cleaners or the porcelain may become damaged during future heating. DO NOT use spray oven cleaners.

The rack may be removed for cleaning. If removed, clean by using a mild, abrasive cleaner following manufacturer's instructions. Rinse with clean water and dry.

General Cleaning

(continued)

Turn the warmer drawer control knob to OFF before removing the drawer. DO NOT touch the warmer drawer element. The element may still be hot enough to cause burns, even if it is dark in color.

RH Glide

Lever

Push down

with screwdriver

Pull up on left glide latch while inserting a screwdriver over the right latch and pushing down

To Remove and Replace Warmer Drawer To Remove Warmer Drawer:

1. Make sure the drawer is COOL. Open the drawer to the fully opened position.

2. Locate the latches on both sides of the warmer drawer. The left latch is visible. However, the right side is not and is located inside the drawer glides.

3. Pull up on the left glide latch while inserting a screwdriver over the right latch and pushing down, while pulling the drawer out.

4. To clean warmer drawer and drawer cavity, see the cleaning chart on page 7.

To Replace Warmer Drawer:

1. Align the glide latches on both sides of the drawer with the slots on the drawer.

2. Push the drawer back in.

LH Glide

Pull up with finger

Lever

Warmer Drawer

Electrical Shock Hazard

can occur and result in

serious injury or death. Disconnect appliance from electric power before cleaning and servicing the warmer drawer.

Avoid Service Checklist

Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

OCCURRENCE

Drawer is not level.

Cannot move appliance easily. Appliance must be accessible for service.

Warmer drawer does not operate.

POSSIBLE CAUSE/SOLUTION

Poor installation. Place a level on the cutout bottom. Make sure bottom is level.

Be sure cutout bottom is strong and stable enough to adequately support drawer (and wall oven, if applicable).

Cabinets not square or are built in too tightly. Contact builder or installer to make appliance accessible.

Make sure cord/plug is plugged tightly into outlet.

Service wiring is not complete. Contact your dealer, installing agent or authorized servicer.

Power outage. Check house lights to be sure. Call your local electric company for service.

WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

GENERAL INFORMATION

The Warm & Serve Drawer can be used:

• As a stand alone appliance

• As a combination Warm & Serve Drawer with a 30" (76 cm) built-in oven mounted above

IMPORTANT: The warmer drawer must be installed on a leveled surface from left to right, rear to front.

Warm & Serve Drawer Dimensions

NOTE: A 60" (152 cm) long cable is supplied with the

Warm & Serve Drawer.

Stand Alone Installation

IMPORTANT: The Warm & Serve Drawer runs off a

single phase three-wire 120 volt, 60 hertz, AC only electrical supply with ground.

Combination Warm & Serve Drawer/

30" (76 cm) Built-in Oven Installation

A. HEIGHT B. WIDTH C. DEPTH

8 " (25 cm) 30" (76,2 cm) 24

D. CUTOUT E. CUTOUT F. CUTOUT

HEIGHT WIDTH DEPTH

Min. 8 Max. 8

8" (21,3 cm) 28

8" (21,9 cm) 28

2 " (72,4 cm) 24" (61 cm)

4 " (73 cm)

8" (62,5 cm)

A. HEIGHT B. WIDTH C. DEPTH

40" (101,5 cm) 30" (76,2 cm) 24

D. CUTOUT E. CUTOUT F. CUTOUT

HEIGHT WIDTH DEPTH

Min. 38

2" (97,8 cm) 28

Max. 39" (99,1 cm) 28

8" (62,5 cm)

2 " (72,4 cm) 24" (61 cm)

4 " (73 cm)

WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS

Important Notes to the Installer

1. Read all instructions contained in these installation instructions before installing appliance.

2. Remove all packing material from appliance before connecting the electrical supply.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Important Note to the Consumer

Keep these instructions for future reference.

IMPORTANT SAFETY INSTRUCTIONS

• Be sure your appliance is installed and plugged

into a 120 Volt grounded outlet.

• This appliance must be electrically grounded in

accordance with the National Electrical Code ANSI/ NFPA No. 70—latest edition in the United States, or CSA C22.1, Part 1 in Canada, and local code requirements.

Tools You Will Need

Phillips® Screwdriver Pencil Ruler or Tape Measure and Straight-edge Hand Saw or Saber Saw Spirit Level

Warm & Serve Drawer Installation

1. Remove the 2 support brackets attached by 2 screws to the top of drawer (see Figure 1). Discard these 2 screws. These brackets are required only if drawer is to be combined with a 30"(76 cm) built-in oven mounted above.

Go to step 2 if warmer drawer is installed under a 30" (76 cm) electric wall oven.

If drawer is to be used as a stand alone drawer, discard support brackets and go to step 3.

2. Insert support bracket tabs in the locating slots on top of warmer drawer. Use the 4 screws removed from sides of warmer drawer to secure support brackets to drawer housing (see Figure 1).

Figure 1

WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS

NOTE: For stand-alone installation, the base must be

capable of supporting 100 lbs. (45 kg). For a combination Warm & Serve Drawer and built-in oven installation, the base must be capable of supporting 250 lbs. (114 kg).

3. Remove the 2 locking plates and 6 screws included in literature package. Mount the locking plates on each side of cabinet opening, along inside of cutout, as shown in Figure 2. Center hole must be 7-5/8" (19,4 cm) from cutout bottom to line up with holes in warmer drawer housing. Use the 2 black screws to fasten each locking plate to the cabinet.

4. Slide drawer into cutout opening until front frame of drawer is flush against cabinet. Be careful not to pinch electrical cord.

5. Open drawer and secure housing to locking plates using the 2 nickel-plated screws supplied. Drive screws from inside drawer into middle hole in each locking plate (see Figure 3). Do not overtighten

screws.

Figure 3

Figure 2

6. The 60" (152 cm) appliance power cord can now be connected into the 120 Volt outlet.

7. Proceed with mounting built-in oven above the drawer (if applicable). Follow installation instructions provided with built-in oven. Make sure to use anti-tip brackets supplied with the built-in oven.

NOTE: Use a piece of cardboard to protect warmer drawer frame and prevent scratching when installing wall oven over warmer drawer.

+ 25 hidden pages