AEG-Electrolux GLHS66EESB User Manual

Use & Care Manual

Side by Side

Welcome 2

Refrigerator

With Electronic Controls

Safety Instructions

Installation --

Ice Maker To Water Supply

Door Removal
Instructions

Features at a Glance

Temperature Controls

Looking Inside

Automatic Ice and Water
Dispenser

Includes Connecting

3

4-5

6

7

8-11

12-14

15-19

Español

READ AND SAVE THESE INSTRUCTIONS

30

Food Storage
& Energy Saving Tips

Normal Operating Sounds

Care & Cleaning

Warranty

Before You Call

Solutions to
Common Problems

22-23

25-29

P/N 241632002 (0503)

20

21

24

Welcome & Congratulations

Congratulations on your purchase of a new refrigerator! We
here at Electrolux Home Products are very proud of our
product and we are completely committed to providing you
with the best service possible. Your satisfaction is our #1
priority.

Please read this Use & Care Manual very carefully. It contains
valuable information on how to properly maintain your new
refrigerator.

We know you’ll enjoy your new refrigerator and Thank You
for choosing our product. We hope you consider us for future
purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating
instructions for your model. Use your refrigerator only as
instructed in this manual. These instructions are not meant
to cover every possible condition and situation that may
occur. Common sense and caution must be practiced when
installing, operating and maintaining any appliance.

Please record your model and serial numbers below for
future reference. This information is found on the serial
plate located inside the refrigerator compartment.

Questions?

1-800-944-9044

(United States)

1-866-213-9397

(Canada)

or visit our web site at www.frigidaire.com

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

• Total freedom from repair bills so

unexpected repairs won’t upset your
budget.

NOTE: Use only soap and water to clean serial plate.

Model Number:

Serial Number:

Purchase Date:

• Fast, convenient toll-free service is just
a phone call away.

• Top-quality repairs by factory-trained
experts.

• Quick access to genuine replacement
parts so you can rest assured your

refrigerator is repaired with the proper
components.

Please attach sales receipt

here for future reference.

Please complete and mail in the

Registration Card

included with your

refrigerator.

Product

2

Important Safety Instructions

Please Read All Instructions Before Using This Refrigerator.

FOR YOUR SAFETY

• Do not store or use gasoline, or other flammable liquids
in the vicinity of this or any other appliance. Read
product labels for warnings regarding flammability and
other hazards.

• Do not operate the refrigerator in the presence of
explosive fumes.

• Avoid contact with any moving parts of automatic ice
maker.

• Remove all staples from the carton. Staples can cause
severe cuts, and also destroy finishes if they come in
contact with other appliances or furniture.

CHILD SAFETY

Destroy or recycle the carton, plastic bags, and any exterior
wrapping material immediately after the refrigerator is
unpacked. Children should NEVER use these items to play
with. Cartons covered with rugs, bedspreads, plastic sheets
or stretch wrap may become airtight chambers, and can
quickly cause suffocation.

These Guidelines Must Be Followed To Ensure That Safety Mechanisms In This Refrigerator
Will Operate Properly.

PROPER DISPOSAL OF YOUR REFRIGERATOR
OR FREEZER

Risk of child entrapment

Child entrapment and suffocation
are not problems of the past.
Junked or abandoned refrigerators
or freezers are still dangerous –
even if they will sit for “just a few
days.” If you are getting rid of your
old refrigerator or freezer, please
follow the instructions below to
help prevent accidents.

Before you throw away your old refrigerator/ freezer:

• Remove doors.

• Leave shelves in place so children may not easily climb
inside.

• Have refrigerant removed by a qualified service
technician.

ELECTRICAL INFORMATION

• The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz., AC only electric outlet.

The power cord of the appliance is equipped with a
three-prong grounding plug for your protection against
electrical shock hazards. It must be plugged directly
into a properly grounded three-prong receptacle. The
receptacle must be installed in accordance with local
codes and ordinances. Consult a qualified electrician.

Do not use an extension cord or adapter plug.

• If the power cord is damaged, it should be replaced by the
manufacturer, service technician or a qualified person to
prevent any risk.

• Never unplug the refrigerator by pulling on the power
cord. Always grip the plug firmly, and pull straight out
from the receptacle to prevent damaging the power cord.

• Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.

• Performance may be affected if the voltage varies by
10% or more. Operating the refrigerator with insufficient
power can damage the compressor. Such damage is
not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall
switch or pull cord to prevent the refrigerator from being
turned off accidentally.

• Avoid connecting refrigerator to a Ground Fault Interruptor
(GFI) circuit.

IMPORTANT: Pressing and holding the On/Off button
for 3 seconds, located on the left side of the
temperature control panel, will disable your

refrigerator’s cooling system, but does not disconnect
the power to the light bulb and other electrical
components. To turn off power to your refrigerator you
must unplug the power cord from the wall outlet.

3

Installation

This Owner’s Guide provides specific operating instructions
for your model. Use the refrigerator only as instructed in this
Use & Care Manual. Before starting the refrigerator, follow

these important first steps.

LOCATION

• Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.

• If possible, place the refrigerator out of direct sunlight
and away from the range, dishwasher or other heat
sources.

• The refrigerator must be installed on a floor that is level
and strong enough to support a fully loaded refrigerator.

• Consider water supply availability for models equipped
with an automatic ice maker.

INSTALLATION

Do Not install the refrigerator where

the temperature will drop below 55°F (13°C) or rise
above 110°F (43°C). The compressor will not be able
to maintain proper temperatures inside the
refrigerator.

Do Not block the toe grille on the
lower front of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator.

Installation Clearances

• Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:

Sides & Top --------------- 3/8”
Back ------------------------ 1”

DOOR OPENING

NOTE: If you refrigerator is placed with the door hinge

side against a wall, you may have to allow additional
space so the door can be opened wider.

Your refrigerator should be positioned to allow easy access to
a counter when removing food. For best use of drawers and
freezer baskets, the refrigerator should be in a position where
both the refrigerator and freezer doors can be fully opened.

TOE GRILLE INSTALLATION / REMOVAL

To Remove Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Working from left side of toe grille, slip your fingers
between top of toe grille and cabinet. Gently pull
forward until first set of tabs are free. Slide your hand
down past the free tabs and pull forward again until the
second set of tabs are free. Continue this process until
all tabs are free and the toe grille can be removed. (See
graphic at top of page in right column.)

To Install Toe Grille:

1. Open freezer and
fresh food
compartment doors.

2. Line up toe grille at
base of refrigerator,
making sure the four
bottom tabs are
resting through holes
at base of cabinet.

3. Starting from left side
of toe grille, press in on first top tab using your thumb
and push toe grille forward until it snaps in place. Continue
this process until all tabs aresnapped in place and toe
grille is secured to refrigerator.

LEVELING

All four corners of your refrigerator must rest firmly on a solid floor.
Your refrigerator is equipped with adjustable front rollers to help
level your unit. To ensure proper door seal and assist door closing,
the refrigerator should be tilted 1/4” (6 mm), front to back.

To Level Your Refrigerator:

1. Remove toe grille. (See

2. Use flat-blade screwdriver or 3/8” socket wrench to adjust

front rollers.

NOTE: The refrigerator doors are designed to shut by
themselves within a 20 degree opening.

3. Check both doors to be sure seals touch cabinet on all four
sides.

“To Remove Toe Grille”

.)

4

Installation

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator

from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

• Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not
recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible
for any damage if plastic tubing is used for supply line.

• DO NOT install water supply tubing in areas where temperatures fall below freezing.

• Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft
water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need

• Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

• Access to a household cold water line with water pressure between 30 and 100 psi.

• A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type
shutoff valve.

• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

- Connecting Ice Maker To Water Supply

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6

meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)
ferrules/sleeves, and instructions for installing a water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply
and flush supply line until water is clear. Turn OFF water supply at shut
off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line,
as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch).
Slide ferrule (sleeve) into valve inlet and finger tighten compression nut
onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of
refrigerator as shown.

7. Coil excess water supply line (about 2½ turns) behind refrigerator as shown
and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that
leak.

9. Reconnect refrigerator to electrical power source.

10. Make sure ice maker power switch is turned On (See page 13 for location of
power switch).

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may
cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be
discolored or have poor flavor. Discard ice made during the first 24 hours.

5

Door Removal Instructions

DOOR REMOVAL INSTRUCTIONS:

If it is necessary to move the refrigerator through narrow doorways, follow
these steps to remove the doors.

IMPORTANT: Before you begin, turn OFF the Electronic Control on your

refrigerator. To turn off all power to your refrigerator you must unplug the
power cord from the wall outlet. Remove any food from door shelves.

1. Disconnect electrical supply.

2. Open both doors, then remove toe grille.

3. Close doors.

To Remove Refrigerator Door:

1. Remove top hinge cover screw on refrigerator door and remove cover.

2. Trace around hinge with soft lead pencil. This will make it easier to realign
doors when they are replaced.

3. Remove top hinge and lift refrigerator door off bottom hinge pin. Set door
aside.

4. Remove bottom hinge, if necessary.

5. Reverse this procedure to reinstall refrigerator door.

To Remove Freezer Door:

1. Disconnect water line coming from lower hinge of freezer door at connection
located under front of freezer: Press outer ring against face of fitting, then pull
to remove tube.

2. Remove top hinge cover screw on freezer door and remove cover.

3. Disconnect wiring harness connector plug at top hinge: place your thumbs on
flat sides of each connector and bend both parts back and forth, then with
firm grasp, pull both pieces apart.

4. Trace around hinge with soft lead pencil. This will make it easier to realign
doors when they are replaced.

5. Remove top hinge, allowing wiring harness to pull through hinge and lift freezer
door off of bottom hinge pin. Lay door down flat to avoid kinking water line.

6. Remove bottom hinge, if necessary.

7. Reverse this procedure to reinstall freezer door.

When both doors have been reinstalled, connect water line by inserting tube and
push until mark touches face of fitting, replace toe grille and plug in electrical power
cord. Turn both temperature controls to center position. Adjust settings as necessary.

6

Features At A Glance

Features may vary according to model

7

Controls & Settings

ALLOWING COOLING TIME BEFORE USE

To ensure reliable food storage, allow your refrigerator and freezer to operate with the doors closed for 8 to 12
hours before placing food inside. During this cooling period, you do not need to adjust the controls, which are
preset at the factory.

SETTING COOLING TEMPERATURES

Your refrigerator comes with a state-of-the-art electronic digital control system. The system’s control panel is
located at the top of the the fresh food compartment.

The two digital displays on the left half of the control panel indicate the current settings or temperatures of your
freezer and fresh food compartments.

do not display the current accurate compartment temperature. Should you desire to see what the current
accurate temperature is, place a separate thermometer inside the freezer or fresh food compartment in the
desired location.

The models with a 2-digit temperature display are for reference only, and

(Temperature Display - Features may vary.)

(Single Digit Display - Features may vary.)

To adjust the temperature to a higher or lower setting, press
the Up (Cold) or Down (Colder) button closest to the display.
The first time you press the button, the display shows current
setting you entered. Each press of the button after that changes
the setting by one.

The display shows your new setting momentarily, then
changes back to the current temperature.

NONO

TETE

NO

TE

NONO

TETE

The advanced electronic control system in your refrigerator includes additional display modes that service
professionals can use to rapidly diagnose performance issues.

8

Controls & Settings

Making Temperature Adjustments

After running your refrigerator for 24 hours, you can adjust temperatures as needed. Make your adjustments
small and gradual, allowing time for temperatures to change and stabilize. Refer to the following guidelines
for temperature settings.

Choosing Fahrenheit or Centigrade

Depending on which temperature standard you
prefer to use, you can set your control panel to
display in fahrenheit or centigrade. To change
between fahrenheit and centigrade, press the Mode
button (located between the two digital temperature
displays).

Press to alternate between
Fahrenheit and Centigrade

What To Do If The Temperature Displays Flash

If either display is continuously flashing, it may indicate that the control system has detected a performance
problem. Call your Electrolux service representative, who can interpret the flashing message.

Numeric Display

Freezer

Fresh

Food

Warmest 1 1

Factory Setting 5 5

Coldest 9 9

Temperature Adjustment Guide

If Fresh Food compartment is too warm

If Fresh Food compartment is too cold

If Freezer compartment is too warm

If Freezer compartment is too cold

Temperature Display (2-Digit)

Freezer Fresh Food

F° C° F° C°

Warmest 6° -14° 47° 8°

Factory Setting 0° -18° 37° 3°

Coldest -6° -21° 33° 1°

Adjust Fresh Food control one degree

colder by pressing Down (Colder) button.

Adjust Fresh Food control one degree

warmer by pressing the Up (Cold) button.

Adjust Freezer control one degree colder

by pressing Down (Colder) button.

Adjust Freezer control one degree warmer

by pressing the Up (Cold) button.

9

Controls & Settings

SYSTEM-MONITORING ALARMS

The electronic control system continuously monitors
your refrigerator/freezer for temperature consistency
and doors left ajar. Variances from normal operating
conditions are communicated by audible tones and
a set of two status indicator lights.

Responding to Alarms (Audible Tones & Indicator Lights)

Your refrigerator’s control system can convey the following information through audible tones and the alarm
indicator lights.

Door

Ajar

Flashing

Green

Freezer or Fresh Food
door has been open for
over five minutes.

Close door to silence and reset alarm.

Air Filter Indicator & Status Lights

Your refrigerator’s fresh food air filter needs to be replaced from time to time. You can monitor the need for
replacement by referring to the status light while the air filter is “ON”. To turn on the air filter, press the “Air
Filter” button. To turn off the air filter, press the “Air Filter” button. To RESET the air filter, press the “Air
Filter” button and hold for 3 seconds.

Air Filter Status Light (not available on all models)

Green

Yellow

Red

Filter OK.

Air filter is about 80 percent used. Please order new one.

Air filter is 100 percent used. Please change now.

10

Controls & Settings

TURNING THE COOLING SYSTEM ON AND OFF

You can disable the cooling system in your
refrigerator by pressing the On/Off button located on
the left side of the temperature control panel.

To ensure that you do not accidentally turn off the
cooling system, the button does not work unless you
press and hold it for three seconds.

While the cooling system is “OFF”, the digital display
will show “OF” “OF” for temperature display models
and “O” “F” for numeric display models.

Once you disable the cooling system, all
refrigeration to the freezer and fresh food
compartments stops.

To turn the cooling system back on, you must again
press and hold the On/Off button for three more
seconds.

IMPORIMPOR

IMPOR

IMPORIMPOR

The On/Off button only controls your refrigerator’s cooling system. Power to lights and other electrical
components continue unless you unplug the power cord.

TT

ANTANT

T

ANT

TT

ANTANT

Cooling System On/Off Button

11

Looking Inside

1

2

ICE CREAM

ICE CREAM

PIZZA SHELF (SOME MODELS)

This shelf is attached to the freezer wall beside the ice dispenser container.
This convenient area allows for storage of pizza and other tall items placed
vertically between the ice dispenser container and the freezer wall.

ICE CREAM SHELF (SOME MODELS)

This shelf attaches to the top of the ice dispenser container. It allows storage
of both round and rectangular cartons of your favorite ice cream.

TIP-UP SHELF (SOME MODELS)

A Tip-Up shelf in the freezer section allows tall items to be easily stored.

To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden temperature change.

CANTILEVER SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual needs. Before
adjusting the shelves, remove all food. Cantilever shelves are supported at
the back of the refrigerator.

Pizza Shelf

To adjust cantilever shelves:

1 Lift front edge up.

2 Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into the wall
bracket. Lower the shelf into the desired slots and lock into position.

* SpillSafeTM

In some models, the
food and for fast cleaning. The shelves slide out independently of their
mounting brackets. Just pull the front of the shelf forward. Shelves can be
extended as far as the stopper will allow but are not removable from their
mounting brackets.

glass shelves (some models) catch and hold accidental spills.

* SpillSafe

TM

shelves slide out for easy access to

1

2

Cantilever Glass Shelf

Ice Cream Shelf

Cantilever Sliding Glass Shelf

* WhiteWestinghouse - SpillFree

TM

12

Looking Inside

(continued)

DOOR STORAGE

Door bins and shelves are provided for convenient storage
of jars, bottles, and cans. Frequently used items can be
quickly selected.

Some models have door bins that can accommodate
gallon-sized plastic drink containers and economy-sized
jars and containers. Some bins are adjustable for
maximum storage capacity.

The dairy compartment, which is warmer than the general
food storage section, is intended for short term storage of
cheese, spreads, or butter.

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be
moved to suit individual needs.

To move door bins

1. Lift bin straight up.

2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports until locked in place.

Fixed Door Bin

TALL BOTTLE RETAINER (SOME MODELS)

The Tall Bottle Retainer keeps tall containers in the bin
from falling forward when opening or closing the
refrigerator door. To install, hold the retainer at the top, and
slide it over the outside wall of the bin, as shown in the
diagram. The Tall Bottle Retainer works best with a Bin
Snugger.

Adjustable Door Bin

SPECIAL ITEM RACK (SOME MODELS)

The innovative design of the Special Item Rack allows
you to store a six-pack of 12 ounce drink cans, a bottle of
wine, a two-liter soft drink bottle, or a carton of eggs. The
Special Item Rack mounts on the left side of your
refrigerator. To install, just slide the Special Item Rack
onto any shelf as shown in the drawing.

Tall Bottle Retainer (left) and Bin Snugger (right)

Special Item Rack

13

Looking Inside -

Special Storage Areas

CRISPERS (SOME MODELS)

The crispers, located under the bottom refrigerator shelf,
are designed for storing fruits, vegetables, and other fresh
produce. Wash items in clear water and remove excess water
before placing them in the crispers. Items with strong odors
or high moisture content should be wrapped before storing.

Crisper Drawer

MEAT KEEPER (SOME MODELS)

Some models are equipped with a Meat Keeper. Meat Keeper
temperatures can be adjusted by sliding the Meat Keeper
Temperature Control in either direction. Use this pan for short
term storage of bulk meat items. If meats are to be kept
longer than one or two days, they should be frozen. The
Meat Keeper is fixed and cannot be moved up or down. If
fruits or vegetables are to be stored in the Meat Keeper, set
the Meat Keeper Temperature Control to a warmer setting to
prevent freezing.

HUMIDITY CONTROL (SOME MODELS)

The Humidity Control, present on some models with crisper
drawers, allows you to adjust the humidity within the crisper.
This can extend the life of fresh vegetables that keep best
in high humidity.

NOTE: Leafy vegetables keep best when stored with
the Humidity Control set on Higher Humidity, or in a
drawer without a Humidity Control. This keeps incoming
air to a minimum and maintains maximum moisture
content.

Crisper Humidity Control

DELI DRAWER (SOME MODELS)

Some models are equipped with a Deli Drawer for storage of
luncheon meats, spreads, cheeses, and other deli items.

Meat Keeper with Temperature Control

WINE RACK (SOME MODELS)

The wine rack stores bottles of wine, or single two-liter plastic
bottles of juice or soda pop. To install, slide the Wine Rack
onto the shelf with the curve facing in. To remove, slide the
Wine Rack out. Install on either side of shelf.

Wine Rack

14

Automatic Ice and Water Dispenser

AUTOMATIC ICE & WATER DISPENSER OPERATING INSTRUCTIONS

1 2

3 4

5

8

Features may vary according to model.

EXTREME To freeze food at a faster rate to preserve freshness, push the Touch Pad for 3-5 seconds to
FREEZE activate this feature. A green light will appear above the Touch Pad. Push the Touch Pad again

for 3-5 seconds to deactivate.

EXTRA To increase ice production for special occasions, such as parties, push the Touch Pad for
ICE 3-5 seconds to activate this feature. A green light will appear above the Touch Pad. Push the

Touch Pad again for 3-5 seconds to deactivate.

CUBE Press the CUBE Touch Pad to get cubed ice. A green light will appear above the Touch Pad.

Press glass against ICE dispensing paddle as far up as possible to catch all ice.

CRUSH Press the CRUSH Touch Pad to get crushed ice. A green light will appear above the Touch Pad.

Press glass against ICE dispensing paddle as far up as possible to catch all ice.

LIGHT Press the LIGHT Touch Pad to turn on dispenser light. Press again to turn the light off.

The light also turns on automatically when ice and/or water is dispensed. Replace light bulb with
an appliance bulb of the same wattage.

FILTER The FILTER STATUS indicator light above the Touch Pad will light up each time the dispenser
STATUS is used. The following filter light indications are:

Green The filter is still operating within its specified life cycle.

Amber The filter has reached approximately 80% of its useful life. This is the recommended time

Red The filter is 100% used up. Change the filter as soon as possible.

After the filter cartridge has been changed, press and hold the FILTER RESET Touch Pad for
10-15 seconds.

NOTE: The Green, Red and Amber lights will flash when reset is completed.

2

3

to purchase a replacement filter.

6

7

9

1

1

2

8

4

8

5

6

5

6

LOCK The Ice & Water Dispenser can be locked out to prevent unwanted use.

To Lock Out Press the LOCK Touch Pad for 3-5 seconds. A Red light will appear above

the Touch Pad.

To Unlock Press the LOCK Touch Pad for 3-5 seconds until the Red light above the

Touch Pad goes out.

WATER To operate the water dispenser, press a glass against the WATER dispensing paddle . To

stop dispensing water, pull the glass away from the dispensing paddle . Dispensed water is not
cold. For colder water, add crushed ice or cubes before dispensing water. A drip tray located at
the base of the dispenser catches small spills and allows them to evaporate. This drip tray is
removable and dishwasher safe. Do not pour water and excess ice in this area because there
is no drain.

15

7

7

9

9

Automatic Ice and Water Dispenser

ON

OFF

Wire

Signal Arm

ICE AND WATER DISPENSER FEATURES

The ice and water dispenser conveniently dispenses chilled water, and ice cubes or crushed ice, depending on the model.

To operate the ice dispenser, select the ice option desired using the touchpad. Press a glass against the dispensing paddle
as far up as possible to catch all ice. To stop dispensing ice, pull glass away from dispensing paddle. Do not remove the
glass until the ice has completely dispensed. (Complete instructions for the dispenser operation are attached to the inside
of the freezer door.)

How the Water Dispenser Works

The water tank, located behind the drawers in the refrigerator compartment, automatically fills as water is dispensed. For
proper dispenser operation, the recommended supply water pressure should fall between 30 psi and 100 psi.

Water pressure must not exceed 100 lbs. Excessive pressure may cause water filter to malfunction.

After the refrigerator is connected to the water supply, fill the water tank by drawing one glass of water. It may take about
1½ minutes after activating the dispenser paddle before water begins to fill this first glass. Continue flushing the system

for 3 minutes to rid the tank and plumbing connections of any impurities. The water dispenser has a built in shutoff device
that will stop the water flow after 3 minutes of continuous use. Simply release the dispenser paddle to reset the shutoff
mechanism.

Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected

to soft water, ensure that the softener is maintained and working properly.

How the Ice Dispenser Works

The ice maker and container are located in the top of the freezer compartment. After the
refrigerator is installed properly and has cooled for several hours, the ice maker can begin
making ice within 24 hours. Air in new plumbing lines may cause the ice maker to cycle two
or three times before making a full tray of ice. To begin ice production, lower the wire signal
arm to the "down" or ON position. With no usage it will take approximately 2 days to fill the
ice container. The ice maker turns off automatically when the ice container becomes full. To
stop the ice maker, lift the wire signal arm until it clicks, and locks in the "up" or OFF
position.

The ice maker produces 4 to 6 pounds of ice every 24 hours depending on usage conditions.
Ice is produced at a rate of 8 cubes every 75 to 90 minutes.

Because of new plumbing connections, the first production of ice cubes may be discolored

or have an odd flavor. These should be discarded until the cubes made are free of discoloration and taste.

ICE DISPENSER TIPS

• Ice cubes stored too long may develop an odd flavor. Empty the ice container and ensure that the wire signal arm is
in its “down” or ON position. The ice maker will then produce more ice.

• Occasionally shake the ice container to keep ice separated.

• Keep the wire signal arm in its “up” or OFF position until the refrigerator is connected to the water supply or whenever the
water supply is turned off.

IMPORTANT: Your ice maker is shipped with the wire signal arm in the ON position. To ensure proper function of
your ice maker, hook up water supply immediately or turn ice maker OFF by lifting the wire signal arm until it clicks
and locks in the UP position. If the icemaker is not turned off and the water supply is not connected, the water valve

will make a loud chattering noise.

If the dispensing paddle is pushed for more than 4 minutes, the dispenser motor may overload
and stop. The overload protector will reset automatically after 3 or 4 minutes.

16

Automatic Ice and Water Dispenser

• If a large quantity of ice is needed at one time, it is best to remove cubes directly from the ice container.

• The following sounds are normal when the ice maker is operating:

• Motor running

• Ice dropping into ice container

• Water valve opening or closing

• Ice loosening from tray

• Running water

• Turn Off the ice maker when cleaning the freezer and during vacations.

• If the ice maker will be turned off for a long period of time, you should also turn off the water supply valve.

CLEANING THE ICE DISPENSER

Do not use the ice chute as a handle when
removing or replacing the ice storage bin.
Surfaces there may be sharp.

Clean the dispenser and ice container at regular intervals, particularly
before you take a vacation or move, or if the ice dispenser sticks.

1. Turn off ice production by pressing the ice maker’s On/Off switch.

2. Remove ice container by lifting up and out. Empty and carefully clean
the container with mild detergent. Rinse with clear water. Do not use
harsh or abrasive cleaners. Allow ice container to dry completely before
replacing in the freezer.

3. Remove ice chips and clean the shelf and chute that supports the ice
container.

4. Replace the ice container. Press the ice maker’s On/Off switch to
resume ice production.

Do not put fingers up ice chute. Surfaces
there may be sharp.

IMPORTANT: When removing or replacing the ice bin, do not

rotate the auger in the ice bin. If the auger is accidentally turned,
you must realign the auger by turning it in 90° turns until the ice bin
fits into place with the drive mechanism.

Remove and empty the ice storage bin if:

1. An extended power failure (one hour or longer) causes ice cubes in
the ice storage bin to melt and freeze together and jam the dispenser
mechanism.

2. The ice dispenser is not used frequently. Ice cubes will freeze together
in the bin and jam the dispenser mechanism. Remove the ice storage
bin and shake to loosen the cubes.

NEVER use an ice pick or similar sharp instrument to break up the ice.
This could damage the ice storage bin and dispenser mechanism.

17

Automatic Ice and Water Dispenser

PureSource TM * Ice and Water Filter (some models)

NOTE: If you purchased a refrigerator with a
and care information.

This ice and water filter system filters water to your ice maker and water dispenser. It is

PureSource

located in the upper right back corner of the fresh food compartment.

System Startup:

Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter. The filter
cartridge has already been installed in the filter housing at the factory. Refer to the
to properly fill the system with water.

Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. The Filter
Status light will turn red after 400 gallons of water has flowed through the ice and
water dispenser (some models). Also, if the filter has been in a refrigerator that
has not been in use for awhile (during moving for example), change the filter
before reinstalling the refrigerator. The dispenser system will also operate without
filtration (with filter cartridge removed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1. Open freezer door and leave open until filter change is complete.

2. Turn the ice maker’s power switch to the Off (“O”) position (See illustration
on page 16).

3. Hold filter cup firmly, and unscrew towards left (Some water could
leak out as you remove cup. This is normal.). Filter cartridge should come
down with cup. If cartridge remains in housing, pull down gently, while
twisting filter back and forth.

4. Rinse out cup under running water.

5. The large o-ring that seals the filter system sets in the o-ring groove
down inside the cup. Should the o-ring fall out during filter cartridge

Order new filter cartridges through the
dealer where you bought the refrigerator,
contact the
1-800-944-9044, or go to our web site at
www.frigidaire.com. It might be good to
order some filter cartridges when you first
install your refrigerator. Be sure to ask for

the

RG-100

cartridge.

the nationally recognized and respected,
not for profit, certification organization for
public health safety. The
system is tested and certified to ANSI/NSF
Standard 42. See performance data sheet
for specifications. This system should not
be used on water that is microbiologically
unsafe or with water of unknown quality
unless the water has been adequately
disinfected before or after traveling through
the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure - 100 PSI

• Maximum Operating Temp. - 100° F

* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter

Customer Care Center

PureSource™*

The

PureSource™

2000 Ice and Water Filter
System with the RG-100
cartridge is tested and
certified by NSF International,

replacement

PureSource™*

at

* NGRG-

replacement, simply place it back in the groove prior to screwing the cup
back in place. If the o-ring becomes damaged, you will need to order one
from the

6. Discard old filter cartridge.

7. Remove new filter cartridge from packaging and place in cup. The end
with the small o-ring should be up, out of the cup.

8. Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall
Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is
completely tightened with

Tighten Past Stop.

9. Turn the ice maker’s power switch to the On (“I”) position.

10. Check for leaks. Open refrigerator door. Wipe any water droplets from the
filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and
reinsert the filter cartridge. Check placement of large O-ring. Reinstall
filter cup, making certain it is tightened completely.

11. To condition filter system and purge air from water line, fill a glass with
water. Continue flushing the system for approximately 3 minutes to assure
that the purest water possible is stored in the water tank.

IMPORTANT: Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to press the

Status

reset button located on the ice and water dispenser. This will reset
the Filter Status light. Push the reset button until the green, red and amber
lights flash (10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer door.

On models without a

Reminder Stickers included in the envelope that the Use & Care Manual
came in. Choose a dated sticker that indicates 6 - 9 months (depending
on your water quality and usage) from the date of installation. Place the
sticker on the front of the filter cup to remind you when it is time to
change the filter.

TM

* Ice and Water filter, please read the following use

Customer Care Center

PureSource™

Filter Status

18

How The Water Dispenser Works

.

logo facing outward. Do Not

reset button, there is a set of

section

Filter

Automatic Ice and Water Dispenser

PureSource2

NOTE: If you purchased a refrigerator with a

TM

* Ice and Water Front Filter (some models)

PureSource2

TM *

Ice and Water front filter, please read the following

use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It is

located in the upper right front corner of the fresh food compartment.

System Startup:

Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter.

The filter cartridge has already been installed in the filter housing at the factory. Refer to the

Works

section to properly fill the system with water.

How The Water Dispenser

Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. The Filter
Status light will turn red after approximately 400 gallons of water has flowed
through the ice and water dispenser. Also, if the filter has been in a refrigerator
that has not been in use for awhile (during moving for example), change the filter
before reinstalling the refrigerator. The dispenser system will also operate without
filtration (with filter cartridge removed and bypass installed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1. Turn the ice maker’s power switch to the Off (“O”) position (See illustration
on page 16).

2. Push the
to release the filter from the housing. To minimize the possibility of the
filter falling out of the housing during removal, it would be best to hold the

Order new filter cartridges through the
dealer where you bought the refrigerator,
contact the
1-800-944-9044, or go to our web site at
www.frigidaire.com. It might be good to
order some filter cartridges when you first
install your refrigerator. Be sure to ask for

the

FC-100

cartridge.

Customer Care Center

PureSource™*

replacement

at

filter as it moves out toward you.

NOTE: A small amount of water may be released during this operation.
You should have a paper towel or dish cloth handy to wipe up any water
that may drip out of the filter or housing. Two small holes near the back of
the housing have been added for any excess water to escape. It would be
best to clear away any food near this area on the top shelf in advance of
removing the filter.

3. Pull the old filter cartridge straight out of the housing.

4. Discard the old filter.

5. Remove the new filter cartridge from the packaging and insert into the

The

PureSource2

Water Filter System NGFC
2000 with the
cartridge FC 100 is tested and

certified by NSF International,
the nationally recognized and respected,
not for profit, certification organization for
public health safety. The
Filter system is tested and certified to ANSI/
NSF Standards 42 and 53. See
performance data sheet for specifications.
This system should not be used on water
that is microbiologically unsafe or with water
of unknown quality unless the water has
been adequately disinfected before or after
traveling through the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure - 100 PSI

• Maximum Operating Temp. - 100° F

* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.

TM*

Ice and

PureSource2

PureSource2

TM*

TM*

filter housing the same way the old one came out.

6. When the cartridge is almost in, you will feel it stop against the clip assembly
in the back of the housing. The clip assembly holds the filter cartridge
firmly in place. At this point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front of the filter cartridge
will be flush with the front of the housing.

7. Turn the ice maker’s power switch to the On (“I”) position.

8. Fill a glass with water. As you are doing this, check for leaks at the filter
housing. There will be noticable spurts and sputters as the system pushes
the air out through the system and out the dispenser nozzle. This is normal.

9. After you have run one glass of water, continue to flush the system for
approximately 3 minutes to assure that the purest water possible is stored
in the water storage tank.

IMPORTANT: Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to press the

Reset

Filter Status light. Push the reset button until the green, red and amber
lights flash (10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer door.

Filter Release Button

, located to the right of the filter cartridge,

button located on the ice and water dispenser. This will reset the

19

Filter

Food Storage & Energy Saving Ideas

FOOD STORAGE IDEAS

Fresh Food Storage

• The fresh food compartment should be kept between 34° F and 40° F with an optimum temperature of 37° F.

• Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven
cooling.

Fruits and Vegetables

• Storage in the crisper drawers traps moisture to help preserve the fruit and vegetable quality for longer time periods.

Meat

• Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not
occur.

Frozen Food Storage

• The freezer compartment should be kept at 0° F or lower.

• A freezer operates most efficiently when it is at least 2/3 full.

Packaging Foods for Freezing

• To minimize dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers.
Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out,
change color, and develop an off-flavor (freezer burn).

• Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

• Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing,
and can raise the temperature of frozen foods.

• Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.

• Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are
best stored in the freezer interior where the temperature varies less.

ENERGY SAVING IDEAS

• Locate the refrigerator in the coolest part of the room, out of direct sunlight,
and away from heating ducts or registers. Do not place the refrigerator
next to heat-producing appliances such as a range, oven, or dishwasher.
If this is not possible, a section of cabinetry or an added layer of insulation
between the two appliances will help the refrigerator operate more
efficiently.

• Level the refrigerator so that the doors close tightly.

• Refer to this Use & Care Manual for the suggested temperature control
settings.

• Periodic cleaning of the condenser will help the refrigerator run more
efficiently. See the

• Do not overcrowd the refrigerator or block cold air vents. Doing so causes
the refrigerator to run longer and use more energy.

• Cover foods and wipe containers dry before placing them in the
refrigerator. This cuts down on moisture build-up inside the unit.

• Organize the refrigerator to reduce door openings. Remove as many
items as needed at one time and close the door as soon as possible.

Care and Cleaning Chart

on page 22.

20

Normal Operating Sounds & Sights

UNDERSTANDING THE SOUNDS YOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliar
sounds. These are all normal sounds and soon will become
familiar to you. They also indicate your refrigerator is operating
as designed. Hard surfaces, such as vinyl or wood floors,
walls, and kitchen cabinets may make sounds more
noticeable. Listed below are descriptions of some of the most
common sounds you may hear, and what is causing them.

NOTE: Rigid foam insulation is very energy efficient,
but is not a sound insulator.

K

A. Evaporator

The flow of refrigerant through the evaporator may
create a boiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigerator
by the evaporator fan.

C. Defrost Heater

During defrost cycles, water dripping onto the defrost
heater may cause a hissing or sizzling sound. After
defrosting, a popping sound may occur.

IMPORTANT: During the automatic defrost cycle, you
may notice a red glow in the vents on the back wall of
your freezer compartment. This is normal during the
defrost cycle.

D. Automatic Ice Maker

If your refrigerator is equipped with an automatic ice
maker, you will hear ice cubes falling into the ice bin.

E. Cold Control & Automatic Defrost Control

These parts can produce a snapping or clicking sound
when turning the refrigerator on or off.

D

B

E

F. Condenser Fan

You may hear air being forced through the condenser
by the condenser fan.

G. Compressor

A

C

F

Modern, high-efficiency compressors operate much
faster than older models. The compressor may have a
high-pitched hum or pulsating sound.

H. Water Valve

G

H

J

I

If your refrigerator is equipped with an automatic ice
maker, you will hear a buzzing sound as the water
valve opens to fill the ice maker during each cycle.

IMPORTANT: Your ice maker is turned On at the factory
so it can work as soon as you install your refrigerator.

To ensure proper function of your ice maker, connect a
water supply immediately or turn the On/Off switch to
the Off (“O”) position.

I. Drain Pan

(not removable)

You may hear water running into the drain pan during
the defrost cycle.

J. Condenser

May create minimal sounds from forced air.

K. Motorized Damper

May produce a light humming during operation.

21

Care & Cleaning

Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills immediately and clean both sections
at least twice a year. Never use any type of scouring pads, brushes, abrasive cleaners or strong alkaline solutions on
any surface. Do not wash any removable parts in a dishwasher.

wall outlet before cleaning.

• When moving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this
may tear or gouge the floor covering. If the refrigerator has an automatic ice maker, be careful not to
move the refrigerator beyond the plumbing connections.

• Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.

• Never use CHLORIDE to clean stainless steel.

NOTES:

• The On/Off button on the Electronic Control only controls your refrigerator’s cooling system. To turn off power to
your refrigerator you must unplug the power cord from the wall outlet.

• Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing
adhesive labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild
detergent, or, touch the glue residue with the sticky side of tape you have already removed. Do not remove the

serial plate.

Always unplug the electrical power cord from the

Care & Cleaning Chart

Part What To Use Tips and Precautions

Interior/Door
Liner

Door Gaskets

Drawers/Bins

Glass Shelves

Toe Grille

Exterior and
Handles

Exterior and
Handles

(Stainless Steel
Models Only)

• Soap and water

• Baking soda and water

• Soap and water

• Soap and water

• Soap and water

• Glass cleaner

• Mild liquid sprays

• Soap and water

• Mild liquid sprays

• Vacuum attachment

• Soap and water

• Non Abrasive Glass

Cleaner

• Soap and water

• Ammonia

• Stainless Steel Cleaners

Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring
excess water out of sponge or cloth before cleaning around controls,
light bulb or any electrical part.

Wipe gaskets with a clean soft cloth.

Do not wash any removable items (bins, drawers, etc.) in dishwasher.

Allow glass to warm to room temperature before immersing in warm water.

Vacuum dust from front of toe grille. Remove toe grille (See illustration on
page 4). Vacuum backside and wipe with sudsy cloth or sponge. Rinse and
dry.

Do not use commercial household cleaners, ammonia, or alcohol to clean
handles. Use a soft cloth to clean smooth handles. Do Not use a dry cloth to

clean smooth doors.

Never use CHLORIDE to clean stainless steel.

Clean stainless steel front and handles with non-abrasive soapy water and a
dishcloth. Rinse with clean water and a soft cloth. Wipe stubborn spots with an
ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel
cleaner. These cleaners can be purchased at most home improvement or
major department stores. Always follow manufacturer's instructions.

NOTE: Always clean, wipe and dry with the grain to prevent cross-grain
scratching. Wash the rest of the cabinet with warm water and mild liquid

detergent. Rinse well, and wipe dry with a clean soft cloth.

22

Care & Cleaning

Refrigerator Light
Located behind
control panel

Wear gloves when replacing light
bulbs to avoid getting cut.

REPLACING LIGHT BULBS

1. Unplug refrigerator.

2. Wear gloves as protection against possible broken
glass.

3. Remove light cover, if necessary.

4. Unscrew and replace old bulb with an appliance bulb
of the same type and wattage.

5. Replace light cover, if necessary.

6. Remember to plug the refrigerator back in.

(continued)

Refrigerator Light Replacement

Short
Vacations

Long
Vacations

Moving

Light Socket
Located Behind
Left Rear
of Crispers

Crisper Light
Cover

or

Light Bulb

Crisper Light Replacement (Models may vary)

Freezer Light Replacement

Vacation and Moving Tips

• Leave refrigerator operating during vacations of 3 weeks or less.

• Use all perishable items from refrigerator compartment.

• Turn automatic ice maker off and empty ice bucket, even if you will only be

gone for a few days.

• Remove all food and ice if you will be gone one month or more.

• Turn off automatic ice maker and turn water supply valve to closed position.

• The On/Off button on the Electronic Control only controls your refrigerator’s

cooling system. To turn off power to your refrigerator you must unplug the
power cord from the wall outlet.

• Clean interior thoroughly.

• Leave both doors open to prevent odors and mold build-up. Block doors open if

necessary.

• Remove all food and ice.

• If using handcart, load from side.

• Adjust rollers all the way up to protect them during sliding or moving.

• Pad cabinet to avoid scratching surface.

IMPORTANT: If the refrigerator is going to be stored or moved in freezing temperatures, the water in
the ice and water system must be drained completely. Failure to do so could result in water leaks when
the refrigerator is put back into service. Contact a service representative to perform this operation.

23

Warranty Information

REFRIGERATOR WARRANTY

FULL ONE-YEAR
WARR ANTY

LIMI TED 2nd– 5TH
YEAR WARRANTY
(Cabinet Liner and
Sealed System)

LIMI TED
WARR ANTY
(Applicable to th e
State of Alask a)

In the U.S.A.. and Puerto Rico, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Home Products,
Inc. In Canada, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Canada Corp. Electrolux Home
Products, Inc. and Electrolux Canada Corp. are referred to in this warranty as “Electrolux”. We authorize no person to change or add to any of our
obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux
servicer.

*NORMAL
RESPONSIBILITIES
OF THE CUSTOMER

EXCLUSIONS This warranty does not cover the following:

IF YOU NEED
SERVICE

This warranty only applies in the 50 States of the U.S.A. and Puerto Rico, and Canada. Product features or specifications as described or illustrated
are subject to change without notice.

USA

WARR ANTY

PERI OD

One year from
original purchase
date.

Second through fifth
years from original
purchase date.

Time periods listed
above.

This warranty applies only to products in ordinary household use, and the consumer is responsible fo
listed below:

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in
accordance with all local plumbing, electrical and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose
connections or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which
are not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.

Not e: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.

2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary
household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by servicers other than Electrolux, or its authorized servicers; use of parts
other than genuine Electrolux parts; obtained from persons other than such servicers; or external causes such as
abuse, misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the
warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all
receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state.
Service under this warranty must be obtained by contacting Electrolux.

800-944-9044

Electrolux Major Appliances North America,
a division of Electrolux Home Products, Inc.
P.O. Box 212378
Augusta, GA 30917

THRO UGH OUR AU THORIZED SERVICERS,

Pay all costs for repairing or replacing any parts of this
appliance which prove to be defective in materials or
workmanship. Excludes original and replacement Ice & Water
filter cartridges (if equipped). Original and replacement
cartridges are warranted for 30 days (parts only).

Repair or replace any parts in the cabinet liner or sealed
refrigeration system (compressor, condenser, evaporator,
dryer or tubing) which prove to be defective in materials or
workmanship.

All of the provisions of the full warranties above and the
exclusions listed below apply.

Your refrigerator is protected by this warranty

WE W ILL:

THE CONSUMER WILL E B

RESP ONSIBLE FO R:

Costs of service calls that are listed under

NORM AL RESPONSIBI LITIES OF THE
CONS UMER.*

Costs for pickup and delivery of the appliance
required because of service. Costs for labor, parts
and transportation other than with respect to the
cabinet liner or Sealed Refrigeration System.

Costs of the technician's travel to the home and any
costs for pick up and delivery of the appliance
required because of service.

Electrolux Major Appliances North America,
a division of Electrolux Home Products, Inc.

6150 McLaughlin Road

866-213-9397

Mississauga, Ontario

r the items

Canada

L5R 4C2

24

1-800-944-9044 (United States)
1-866-213-9397 (Canada)

Before You Call

Visit our web site at
www.frigidaire.com.

PROBLEM CAUSE CORRECTION

RUNNING OF REFRIGERATOR

Compressor does not run.

Refrigerator runs too
much or too long.

• Freezer control is set to "OF".

• Refrigerator is in defrost cycle.

• Plug at wall outlet is

• House fuse blown or tripped

• Power outage.

• Room or outside weather is

• Refrigerator has recently been

• Automatic ice maker is

• Doors are opened too

• Refrigerator/freezer door may

• Freezer control is set too cold

• Refrigerator/freezer gasket is

• Condenser is dirty.

disconnected.

circuit breaker.

hot.

disconnected for a period of
time.

operating.

frequently or too long.

be slightly open.

(control found in refrigerator
section).

dirty, worn, cracked, or poorly
fitted.

• Set freezer control. See Temperature Controls section.

• This is normal for a fully automatic defrost refrigerator.

The defrost cycle occurs periodically, lasting about 30
minutes.

• Ensure plug is tightly pushed into outlet.

• Check/replace fuse with a 15 amp time-delay fuse.

Reset circuit breaker.

• Check house lights. Call local Electric Company.

• It’s normal for the refrigerator to work longer under

these conditions.

• It takes 8-12 hours for the refrigerator to cool down
completely.

• Ice maker operation causes refrigerator to run slightly
more.

• Warm air entering the refrigerator causes it to run
more. Open doors less often.

• Ensure refrigerator is level. Keep food and containers
from blocking door. See PROBLEM section
OPENING/CLOSING OF DOORS/DRAWERS.

• Set refrigerator control to warmer setting until
refrigerator temperature is satisfactory. Allow 24 hours
for temperature to stabilize.

• Clean or change gasket. Leaks in door seal will cause
refrigerator to run longer in order to maintain desired
temperatures.

• Clean condenser. See
and Cleaning section.

Care & Cleaning Chart

in Care

Compressor goes off and
on frequently.

• Thermostat keeps the
refrigerator at a constant
temperature.

TEMPERATURES ARE TOO COLD

Freezer temperature too
cold. Refrigerator
temperature is satisfactory.

Refrigerator temperature
too cold. Freezer
temperature is satisfactory.

Food stored in drawers
freezes.

Food stored in Meat
Keeper freezes (some
models).

Digital temperature
displays are flashing.

• Freezer control is set too cold. • Set freezer control to a warmer setting. Allow 24 hours

• Refrigerator control is set too

cold.

• Refrigerator control is set too
cold.

• Meat Keeper Temperature
Control set too cold.

• Electronic control system has
detected a performance
problem.

• This is normal. Refrigerator goes on and off to keep
temperature constant.

for temperature to stabilize.

• Set refrigerator control to a warmer setting. Allow 24
hours for temperature to stabilize.

• See solution above.

• Adjust Meat Keeper Temperature Control to a lower

setting. (Meat should be stored at a temperature just
below the freezing point for maximum fresh storage
time. It is normal for ice crystals to form due to the
moisture content of meat.)

• Call your Electrolux service representative, who can
interpret any messages or number codes flashing on
the digital displays.

25

Before You Call

(continued)

PROBLEM CAUSE CORRECTION

TEMPERATURES ARE TOO WARM

Freezer/Refrigerator
temperature is too warm.

Freezer temperature is too
warm. Refrigerator
temperature is satisfactory.

Refrigerator temperature is
too warm. Freezer
temperature is satisfactory.

Temperature in the Meat
Keeper is too warm (some
models).

Doors are opened too

•

frequently or too long.
Door is slightly open.

•

Condenser is dirty.

•

Freezer control is set too

•

warm.

Refrigerator control is set too

•

warm.

Meat Keeper Temperature

•

Control is set too warm.

WATER/MOISTURE/FROST INSIDE REFRIGERATOR

Moisture collects on inside
of refrigerator walls.

Water collects on bottom
side of drawer cover.

Weather is hot and humid.

•

Door is slightly open.

•

Door is opened too often or too

•

long.
Open containers.

•

Vegetables contain and give

•

off moisture.

Warm air enters the refrigerator whenever the door is

•

opened. Open the door less often.
See

•

•

•

•

•

•

•

•

•

•

•

PROBLEM

DOORS/DRAWERS

Clean condenser. See

and Cleaning

Set freezer control to a colder setting. Allow 24 hours
for temperature to stabilize.

Set refrigerator control to a colder setting. Allow 24
hours for temperature to stabilize.

Adjust Meat Keeper Temperature Control to a colder
setting.

The rate of frost buildup and internal sweating
increases.
See

PROBLEM

DOORS/DRAWERS

Open door less often.

Keep containers covered.

It is not unusual to have moisture on the bottom side of
the cover.
Move humidity control (some models) to lower setting.

section

section

section

OPENING/CLOSING OF

.

Care & Cleaning Chart

.

OPENING/CLOSING OF

.

in

Care

Water collects in bottom of
drawer.

Washed vegetables and fruit

•

drain while in the drawer.

WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR

Moisture collects on
outside of refrigerator or
between doors.

Weather is humid.

•

Door is slightly open, causing

•

cold air from inside refrigerator
to meet warm air from outside.

AUTOMATIC ICE MAKER

Ice maker is not making
any ice.

Ice maker wire signal arm is in

•

the “up” or
Household water line valve is

•

not open.
Freezer is not cold enough.

•

Saddle valve on cold water

•

pipe is clogged or restricted by
foreign material.
Check to see if the water

•

dispenser is dispensing water.

OFF

position.

Dry items before putting them in the drawer. Water

•

collecting in bottom of drawer is normal.

This is normal in humid weather. When humidity is

•

lower, the moisture should disappear.
See

•

•

•

•

•

•

PROBLEM

DOORS/DRAWERS

Move wire signal arm to the “down” or ON position.

Turn on household water line valve.

See

PROBLEM

.

WARM

Turn off household water line valve. Remove valve.
Ensure that valve is not a self-piercing saddle valve.
Clean valve. Replace valve if necessary.
If not, the ice & water filter cartridge is clogged or
restricted by foreign material, and must be replaced.

section

.

section

OPENING/CLOSING OF

TEMPERATURES ARE TOO

26

Before You Call (

continued)

PROBLEM CAUSE CORRECTION

AUTOMATIC ICE MAKER

Ice maker is not making
enough ice.

Ice maker will not stop
making ice.

Ice maker is not separating
the ice cubes.

Ice has bad odor and taste.

(CONTINUED)

• Ice maker is producing less ice

• Freezer is not cold enough.

• Household water line valve is

• Check to see if water

• Ice maker wire signal arm is

• Ice cubes are not being used

• Ice cubes are hollow or smaller

• Ice has picked up odor or

• Water running to ice maker

• Ice not used frequently enough.

than you expect.

not completely open.

dispenser is dispensing slower
than normal.

being held down by some item
in the freezer.

frequently enough.

than normal.

flavor from strong food stored
in refrigerator or freezer.

has poor taste or odor.

• Ice maker should produce approximately 4 – 5 pounds
of ice every 24 hours.
pounds of ice every 24 hours.

• See PROBLEM section TEMPERATURES ARE TOO
WARM.

• Turn on household water line valve.

• If it is, replace the ice & water filter cartridge.

• Move item and release wire signal arm. Remove any

ice cubes that are frozen together over the wire signal
arm.

• Remove and shake ice container to separate cubes.

• The ice & water filter cartridge may be clogged.

Replace filter cartridge.

• Cover foods tightly. Discard stale ice. Ice maker will
produce fresh supply.

• Add filter to water supply line. Consult a water
purifying company.

• Discard stale ice.

Extra Ice

should produce up to 6

ICE DISPENSER

Dispenser will not dispense
ice.

Ice dispenser is jammed.

• Ice storage container is empty.

• Freezer temperature is set too

warm.

• Household water line valve is
not open.

• Freezer door is not closed.

• Ice dispensing arm has been

held in for more than 4-5
minutes.

• Ice has melted and frozen
around auger due to infrequent
use, temperature fluctuations,
and/or power outages.

• Ice cubes are jammed
between ice maker and back
of ice container.

• Ice cubes are frozen together.

• Ice cubes are hollow or smaller

than normal.

• When the first supply of ice is dropped into the
container, the dispenser should operate.

• Turn freezer control to a higher setting so that ice
cubes will be made. When first supply of ice is made,
dispenser should operate.

• Open household water line valve. Allow sufficient time
for the ice to be made. When ice is made, the
dispenser should operate.

• Ensure freezer door is closed.

• Motor is overloaded. Motor overload protector will

reset in approximately 3 minutes. Ice can then be
dispensed.

• Remove ice container, thaw, and empty the contents.
Clean container, wipe dry, and replace in proper
position. When new ice is made, dispenser should
operate.

• Remove ice cubes that are jamming the dispenser.

• Use the dispenser often so that cubes do not freeze

together.

• The ice & water filter cartridge could be clogged.
Replace the filter cartridge. Dispensing system
operates best at 30 – 100 psi water pressure. Well
water pressures should fall within this range.

27

Before You Call

(continued)

PROBLEM CAUSE CORRECTION

WATER DISPENSER

Dispenser will not
dispense water.

Water has an odd taste
and/or odor.

Water pressure is
extremely low.

ODORS IN REFRIGERATOR

Interior is dirty.

• Household water line valve is
not open.

• Freezer door is not closed.

• Ice & water filter cartridge is

clogged.

• Front filter not fully installed, if
equipped

• Water has been in the tank for
a period of time.

• Unit not properly connected to
cold water line.

• Tubing used in the household
water supply and installation
may affect water taste and
odor.

• Water has a high mineral
content.

• Cut-off and cut-on pressures
are too low (well systems
only).

• Reverse osmosis system is in
regenerative phase.

• Interior needs to be cleaned.

• Food with strong odors is in

refrigerator.

• Open household water line valve. See PROBLEM
section ICE MAKER IS NOT MAKING ANY ICE.

• Ensure that freezer door is closed.

• Replace filter cartridge.

• Push filter in until you hear a “click”. Filter should be

flush with cabinet.

• Draw and discard 10 – 12 glasses of water to freshen
the supply and completely rinse out the tank.

• Connect unit to cold water line that supplies water to
the kitchen faucet.

• For best results, use copper tubing for water
connections.

• Contact water treatment plant for help.

• Have someone turn up the cut-off and cut-on pressure

on the water pump system (well systems only).

• It is normal for a reverse osmosis system to be below
20 psi during the regenerative phase.

• See

• Cover food tightly.

Care & Cleaning Chart

section.

OPENING/CLOSING OF DOORS/DRAWERS

Door(s) will not close.

Drawers are difficult to
move.

LIGHT BULB IS NOT ON

Light bulb is not on.

• Door was closed too hard,
causing other door to open
slightly.

• Refrigerator is not level. It
rocks on the floor when moved
slightly.

• Refrigerator is touching a wall
or cabinet.

• Food is touching shelf on top
of drawer.

• Track that drawers slide on is
dirty.

• Light bulb is burned out.

• Light switch is stuck.

• No electric current is reaching

refrigerator.

• Close both doors gently.

• Ensure floor is level and solid, and can adequately

support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.

• Ensure floor is level and solid, and can adequately
support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.

• Keep less food in drawer.

• Clean drawer, rollers, and track. See

section.

Chart

• See

• Light switch is located on side of refrigerator and

• See PROBLEM section RUNNING OF

Replacing Light Bulbs

section.

freezer liners.

REFRIGERATOR.

in Care and Cleaning

Care & Cleaning

28

Before You Call

(continued)

IF YOU HEAR:

5 beeps

3 beeps

• A door has been left open for 5
minutes or more.

• The refrigerator has experienced a
loss of power or a low voltage
condition.

• These beeps will repeat once every minute until the
door has been closed. This is normal for the “Door
Ajar” alarm.

• This is normal when “Power-On-Reset” is activated.

29