Favorit 45250Vi
Dishwasher
Posudomoe^naq ma[ina
Instruction booklet
Rukowodstwo po \kspluatacii
Dear customer,
please read these user instructions carefully. Please observe the
safety instructons on the first few pages of this instruction book.
Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its
life can be properly informed on appliance use and safety.
The warning triangle and/or specific words (Warning!, Caution!,
Important!) are used to highlight instructions that are important for
your safety or for the function of the appliance. It is imperative that
these instructions are observed.
This symbol or numbered instructions lead you step by step through
the operation of the appliance.
Next to this symbol you receive additional information and practical
tips on using the appliance.
Tips and instructions for the economical and environmentally friendly
use of the appliance are marked with a clover leaf.
In the event of a malfunction, these operating instructions contain
information on how to rectify faults yourself, see the section ”In the
event of a fault”.
If these instructions are insufficient, please contact your Service Centre.
This dishwasher has a new feature called ”IMPULSE WASHING”.
This washing system varies both the revolutions of the pump
and the water pressure for more intensive cleaning of the dishes
during the programme.That is why different sections of the programme cycle do not sounds the same.
Printed on paper manufactured with environmentally sound processes.
He who thinks ecologically acts accordingly...
2
Contents
Instruction book.................................................4-23
Safety information.............................................................4
Disposal ............................................................................6
General information...........................................................7
Description of the appliance..............................................8
Prior to using for the first time.........................................10
Programme chart ............................................................14
Loading the dishes..........................................................16
Using the appliance ........................................................17
Care and cleaning...........................................................20
In the event of a fault......................................................22
Service ..............................................................24-25
Service and spare parts..................................................24
Information for test centres.............................................25
Position- and connection instructions...........26-35
Technical specifications...................................................26
Installation.......................................................................27
Rukowodstwo po zkspluatacii ...........................36
Contents
822 61 10-99 3
Instruction book
Instruction book
Safety information
The safety aspects of AEG electrical appliances comply with accepted
technical standards and the German Appliance Safety Law.
Nevertheless, as a manufacturer we consider it our obligation to
make you aware of the following safety information:
General safety
● Only wash household dishes using the dishwasher. If the appliance
is used for other purposes, or is used incorrectly, the manufacturer
cannot accept any liability for any damage caused.
● Additions or modifications to the dishwasher are not permitted for
safety reasons.
Before using the dishwasher for the first time
● Check the dishwasher for transport damage. Never connect a
damaged machine. In the case of damage, please contact your
retailer.
● For information on how to correctly install and connect up your
dishwasher, please read the ”Installation” section.
● Before installing the appliance, ensure that the nominal voltage and
type of supply on the rating plate match that of the supply where
the appliance is to be installed. The fuse rating can also be found
on the rating plate.
Child safety
● Remember that the plastic bags included in the packaging can be
fatal playthings for small children.
● Children may not recognise the dangers of improper use of electrical
appliances. You should therefore ensure proper supervision during
operation and not allow children to play with the dishwasher.
● Detergents may have a caustic effect on eyes, mouth and throat
and may even cause suffocation. Keep all detergents in a safe
place out of children´s reach.
● The water in your dishwasher is not suitable for drinking. If there are
still remnants of degergent in the appliance, there is a risk of burns.
Keep children well away from the dishwasher when its door is open.
4
Instruction book
In daily use
● Never place the dishwasher in operation if the mains cable, water
inlet or drain hose is damaged, or the control panel, or plinth area is
damaged such that the inside of the appliance is freely accessible.
● In the event of a fault, first close the tap, then switch off the appliance
and unplug it from the mains. If the appliance is permanently wired to
the mains, remove the fuse.
● When removing the electrical plug, grip the plug, not the lead.
● Servicing and possible repairs must be carried out by a service
company authorized by the supplier. Use only spare parts supplied
by these. Never try to repair the dishwasher yourself, repairs carried
out by unauthorized or inexperienced persons can cause injury or
serious malfunctioning.
● If the mains lead is damaged, or is to be replaced for a longer lead,
the cable (obtainable from AEG Service Force) must be replaced by
a service engineer authorised by AEG.
● Do not put any solvents in the dishwasher. There is a risk of an
explosion!
● Do not sit or stand on the open door, the appliance may tip over.
● Before using special dishwasher salt, detergent or rinse aid, make
sure that the manufacturer of these products expressly specifies
their use in domestic dishwashers.
● Do not place sharp knives with their points upwards. It is much safer
to lay them horizontally in the basket.
● Ensure that the door of the dishwasher is always closed when it is
not being loaded or unloaded. In this way you will avoid anybody
tripping over the open door and hurting themselves.
● The water safety system protects against water damages. The follo-
wing requirements must be fulfilled:
- The dishwasher must remain connected to the mains supply when
switched off.
- The dishwasher must be correctly installed.
- Always shut off the water supply whenever the dishwasher is left
unattended for an extended period.
5
Instruction book
Disposal
Disposing of the packaging material
Caution!
Never leave packaging material in a place where children may play
with it.
All materials used in packaging this appliance are environmentallyfriendly. The cardboard components of the packaging are made from
recyclable paper and should be taken to a collection point for recycling.
>PE< stands for polyethylene, which is used for the bag around
the appliance and the bag in which these instructions were
supplied.
>PS< stands for polystyrene (moulded), which is used for the sections
of packaging needed to cushion the appliance.
Disposal of old appliances
The symbol on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local
city office, your household waste disposal service or the shop where
you purchased the product.
6
General information
Economical and ecological dishwashing
● Only connect the dishwasher to the hot water supply, if your hot water
is not electrically heated.
● Ensure that the water softener is correctly adjusted.
● Do not pre-rinse dishes under running water.
● Select the wash programme to suit the nature and degree of the
soiling on the dishes.
● Do not use more detergent, special salt or rinse aid than is recom-
mended in this instruction booklet and by the detergent manufacturer.
For washing in the dishwasher the following
are not suitable:
- wooden platters
- plastic items that are not heat resistant
- lead crystal glass
- pewter or copper items
- bonded cutlery items or dishes
- older cutlery with cement that is not temperature resistant
- cutlery with wooden, horn, china or mother of pearl handles
Instruction book
For washing in the dishwasher the following
are of limited suitability:
- Only wash stoneware in the dishwasher if it is specifically marked
as being dishwasher safe by the manufacturer.
- Glazed patterns may fade if machine washed frequently.
- Silver and aluminium parts have a tendency to discolour during
washing. Left-overs, e.g. egg white, egg yolk and mustard often
cause discolouring and staining on silver. Therefore always clean
left-overs from silver immediately, if it is not to be washed straight
after use.
- Some types of glass can become dull after a large number of washes.
Make sure you always buy articles that are dishwasher safe.
7
Instruction book
Description of the appliance
4 5
1 Spray arm
2 Coarse filter/microfilter
3 Fine filter
4 Detergent dispenser
5 Rinse aid dispenser
6 Salt container
8
Instruction book
The control panel
On/Off button
Indicator lamps
delayed start
Water softener
button
Control lamps
A
Buzzer
button
Programme
buttons
Combination buttons ”A”:
In addition to selecting a programme, you can press these two buttons to
adjust the setting of the water softener, switch off the buzzer and cancelling a pre-set programme.
Delay start
button
Control lamps:
Shows that • Refilling of salt is necessary
• Refilling of the rinse aid
is necessary
• Programme cycle ended
9
Instruction book
Prior to using for the first time
Adjusting the water softener
To prevent the build up of lime on the dishes and in the dishwasher, the
dishes must be washed with soft water i.e. water with a low lime content.
This dishwasher is equipped with a water softener in which tap water from
a hardness of 4°d (german degree) is softened with the aid of special salt.
Adjust the water softener according to the table below for the water
hardness level for your area. Contact your local Water Authority to find
the exact water hardness level for your area.
The water softener has 5 settings:
Water hardness
1)
°d
mmol/l
> 24 > 4,2
18 - 24 3,2 - 4,2
12 - 18 2,1 - 3,2
4 - 12 0,7 - 2,1
below 4 below 0,7
Setting on the
2)
water softener
5
4
3*
2
1
Number of light
and sound signals
5
4
3
2
1
no salt is needed
1) german degree of measurement for the water hardness
2) millimol, internationel unit for water hardness
*) factory setting
The dishwasher must be switched off.
1. Press in the On/Off button.
2. Press the combination buttons simultaneously and hold them pressed
in. When the first three programme indicator lamps starts to flash, you
can let go of the buttons.
3. Press the water softener button once. The lamps for the water softener
and for the ended programme cycle starts to flash and a buzzer will
sound, unless it is switched off.
- The number of flashes for the ended programme cycle and sound
signals are equivalent with the set water hardness level.
- This sequence of flashes and sound is repeated several times after
a few seconds pause.
4. The water hardness level is raised by 1 step every time you press the
water softener button.
10
After hardness level 5 comes hardness level 1.
5. Once the hardness setting is set correctly, press the On/Off button.
If the setting 1 is chosen, the salt indicator lamp is not lit.
Instruction book
Filling with salt for the water softener
Caution!
Use only salt designed for dishwashers. Never fill the salt container with
any another type of salt or dishwasher detergent as this would irreparably
damage the water softener.
Prior to filling with salt, please check each time that you really do have a
packet of dishwasher salt in your hand.
1. Unscrew the filler cap to the
salt container anticlockwise.
2. Fill the salt container with
water (only the first time).
3. Fill the container with coarse
salt, using the funnel supplied.
4. Remove the funnel and wipe
off any spillage around the
filler opening.
5. Screw the filler cap back
properly in place.
Fill with dishwasher salt:
When the indicator light on the control panel is lit.
11
Instruction book
Filling the rinse aid
Use of rinse aid will result in cleaner and faster drying of the load, since it
helps water and soil to run off. Too much rinse aid may result in streakiness,
too little may cause white spots.
Caution!
Only use rinse aid specifically designed for domestic dishwashers. Never fill
the rinse aid dispenser with any other substance (e.g. vinegar concentrate
or dishwasher detergent) as this would damage the appliance.
The rinse aid dispenser is on the inside of the dishwasher door.
1. Open the lid to the dispenser by
pressing the lid catch towards the
compartment and lift the lid.
2. Fill up with rinse aid; do not overfill.
3. Wipe off any spillage carefully to
prevent excessive foaming during
the next wash programme.
4. Close the lid and press until it locks
again.
Fill with rinse aid:
When the indicator light on the control panel is lit.
Adjusting rinse aid dosing
The dispenser holds about 150 ml. This is enough for approx. 60 wash
cycles, depending on the dosage setting. Adjust the dosage setting
according to the hardness of the water.
You can set the dosage between 1 - 6, equivalent to 1 - 6 ml rinse aid.
Factory setting is 1. Begin at the lowest dosage setting and increase if
necessary by turning the setting arrow with e.g. the handle of a spoon.
12
Instruction book
Filling with detergent
Caution!
Only use detergents specially designed for dishwashers.
The detergent is released into the wash water during the programme.
Please observe the manufacturer’s dosing and storage recommendations
as stated on the detergent packaging. Remember that the instructions
usually refer to full-size dishwashers, for example when using detergent
tablets, it is sufficient to use just half a tablet.
1. Open the lid to the dispenser by pressing
the lid catch towards the compartment.
2. Filling with detergent.
Pre-wash detergent is poured into the
smaller compartment to the left when
needed.
3. Close the lid.
Avoid frequent use of liquid detergents, as the long term effects
of such detergents create a potential risk of increasing pump
noise.
Detergent tablets
Detergent tablets of different makes dissolve at different speeds.
For this reason some detergent tablets cannot develop their full
cleaning power during short programmes. Therefore please use
normal programmes with pre-wash when using detergent tablets.
13
Instruction book
Programme chart
Type of dishes
Type of soil:
Suitable
programme:
Programmecycle:
Washing time with
drying:
Drying time:
Energy:
2)
2)
2)
Plates and cooking
pots
• heavily soiled
• dried-on food
remnants especially
eggwhite and starch
INTENSIV
70°
1)
Pre-wash
Washing
2 x rinses
Final rinse
Drying
112 minutes
13 minutes
1,15 kWh
All types of dishes
• normally soiled
• dried-on food
remnants
NORMAL
65°
Pre-rinse
Washing
Rinse
Final rinse
Drying
92 minutes
13 minutes
0,80 kWh
Water:
2)
9 litres
7 litres
1) Noise levels vary at different stages of the wash programme as at
some programme stages the dishes are washed more energetically
so that they will be cleaned more thoroughly.
2) The consumption figures were determined under standard conditions.
They are intended as a guide only and depend on the loading. For
this reason figures may vary in practice.
All programmes begin with a drain.
14
Instruction book
All types of dishes
• normally soiled
ECO
50°
Pre-rinse
Washing
Rinse
Final rinse
Drying
150 minutes
54 minutes
0,63 kWh
• lightly soiled
35 MIN
50°
Washing
Rinse
Final rinse
35 minutes
-
0,40 kWh
Coffee cups,
delicate items
• lightly soiled
GLASS
40°
Washing
Rinse
Final rinse
30 minutes
-
0,35 kWh
7 litres
6 litres
6 litres
15
Instruction book
Loading the dishes
● Always place glasses, cups and bowls upside down.
● Incline deep dishes (soup plates etc.) so that the water can run off
when drying.
● Make sure that the dishes do not rest against each other. This is
particularly important in regard to the cutlery basket - nested spoons,
etc. simply cannot be properly washed. The water must get at all the
soiled surfaces.
● Make sure that cutlery with slender handles and other items do not
protrude through the openings in the basket and prevent the spray
arm from rotating.
● Never put silver and stainless steel objects together. When these
metals come into contact with each other a chemical reaction occurs
which stains the silver.
● When washing delicate items, select the programme with the lower
wash temperature.
● Substances such as ketchup containing strong colouring agents can
cause temporary discolouration to the interior of the dishwasher.
Caution!
Do not place sharp knives with their points upwards. It is much safer
to lay them horizontally in the main basket.
16
The cup shelves can be placed in two different levels.
Baskets
Main basket
Cutlery basket
Using the appliance
Starting the programme
1. Scrape off solid food remnants.
2. Load the dishwasher.
3. Put the correct amount of detergent into the detergent dispenser
and close the dispenser lid.
4. Press in the On/Off button. All programme indicator lamps are lit.
5. Press in the required programme button (see programme chart).
All other programme indicator lamps goes out.
6. Close the door.
Stopping the programme temporarily
1. Open the door. The programme stops.
2. The programme indicator lamp is lit.
3. Close the door and the programme continues after about 6 seconds.
Open the door carefully when the dishwasher is running, since hot
steam may escape.
Cancelling the programme
1. Open the door.
2. Press and hold in the combination buttons, the machine goes to
starting position and all programme indicator lamps are lit.
Instruction book
3. Release the buttons. The programme is now cancelled and a new
programme can be selected.
If you switch the dishwasher off, the selected programme is not
finished, it is only disrupted. When you start the dishwasher again,
the programme will continue.
Pause function
With the paus function the programme can be temporarily disrupted for a
short period of time.
1. Open the door and press the On/Off button. The programme stops.
2. All lamps goes out.
3. When you want the programme to continue again, press the On/Off
button once more and close the door. The programme continues.
The programme should not be paused for any longer than necessary,
because the water inside the dishwasher has cooled down and must
be heated again which increases the power consumption.
17
Instruction book
Cancelling the drying phase
In case you do not want to wait until the drying phase is completed, you
can cancel it by open the door. The drying phase is now cancelled.
Setting the delay start
The programme start can be delayed by 3, 6 or 9 hours.
1. Press in the On/Off button.
2. Press the delay start button repeatedly, until the lamp next to the
required hours of delay is lit.
3. Press the button for the required programme.
4. After the set delayed start time has elapsed, the programme starts.
Reset the delayed start:
If the programme has not started, you can change the set time with the
delay start button.
Cancelling the delayed start:
If the programme has not started, the delayed start can be cancelled. Press
the delay start button repeatedly, until none of the lamps next to the hours
are lit. The required programme starts immediately.
Switching the buzzer off
Before switching the buzzer off must all programmes have completed.
1. Press in the On/Off button.
2. Press the combination buttons simultaneously and hold them pressed in. When the first three programme indicator lamps starts to
flash, you can let go of the buttons.
3. Press the buzzer button once. The lamp for the buzzer button
starts to flash and the lamp for the ended programme cycle is lit.
Press the button once more and the lamp for the ended programme
cycle goes out. Now the buzzer is off.
4. Press out the On/Off button to complete the setting.
To reset the function, follow steps 1 and 2 above and then press
the buzzer button twice, until the lamp for the ended programme
cycle is lit again.
18
Instruction book
Switching the dishwasher off / unloading
Switch the dishwasher off when the buzzer for ended programme sounds
(approx. 15 seconds) or the lamp for the ended programme cycle is lit.
1. Open the door and press the On/Off button.
2. Leave the dishes in the dishwasher for approx. 15 minutes after
the end of the programme so that they dry better and cool down.
3. Check the filters to see if they need to be cleaned when the dishwasher has finished the programme.
Hot dishes are sensitive to mechanical shocks. Always let the dishes cool down before unloading.
19
Instruction book
Care and cleaning
Machine
Clean the outside surfaces of the appliance using a mild (non-abrasive)
household cleaning product. Finish by removing remaining traces of
the product with a damp cloth.
Caution!
Do not use cleaning products which contain alcohol (spirits), thinners
and similar substances.
Spray arm (1)
It is important to keep all the holes in the spray arm clear. Aclogged
hole can seriously affect washing efficiency. If the spray arm needs
cleaning, unscrew the nut anti-clockwise, remove the washer and lift
off the spray arm. Clear the holes and shake out any food remnants.
Coarse filter/microfilter (2)
The purpose of the coarse filter is to catch large objects such as
toothpicks and pieces of eggshell. Make sure that the filter is always
clean. Turn the coarse filter anti-clockwise. Lift it out and rinse it
under running water whenever necessary.
Fine filter (3)
It is just as important to keep this filter clean. Adirty or clogged filter
will always impair washing efficiency. The fine filter can easily be lifted
out for cleaning when you have removed the coarse filter.
20
Cleaning the outer door
It is possible to remove the outer door
from the plastic door in order to clean
inside it if necessary.
1. Unscrew the screws that hold
the guides in the upper corners
of the plastic door.
2. The outer door should be
supported when opened out
in order to prevent the hinges
from breaking off.
3. If necessary, the door can be
dismounted completely by
inserting a screwdriver or
similar tool into the predrilled
holes of the shelf under the
hinges snap function.
When mounting the outer door, snap
the hinges into place and screw the
guides back.
Instruction book
Protecting against freezing
Caution!
If the dishwasher is placed in an environment where the temperature sometimes fall below 0° C, there is a risk that the small amount of water which
remains inside the parts of the dishwasher will freeze and damage it.
1. Turn off the water supply to the dishwasher.
2. Remove the water inlet and discharge hoses.
3. Make sure that there is dishwasher salt in the salt container for the
water softener.
The appliance is only to be used and stored indoors at normal
room temperature. The manufacture is not responsible for any
frost damage.
21
Instruction book
In the event of a fault
Before calling out an engineer, please check through the details
below because some faults can be rectified easily without the
need to call out an engineer.
Fault
The programme will not
start.
The dishwasher is not
filling with water.
Water not discharged at
end of cycle.
Dishes not washed satisfactorily.
Check
Is the door closed properly?
Have you pressed the On/Off button?
Is the water tap turned on?
Is the dishwasher plugged in?
Has the fuse blown?
Is the delayed start-button pressed in?
Is the previous programme finished?
Is the water tap turned on?
Has your domestic water supply been cut
off temporarily?
Is the water inlet hose kinked or blocked?
Is the filter inside the inlet hose blocked?
Is the water pressure too low?
Did you open the door before the programme cycle finished?
Are the filters clogged?
Has anything prevented the spray arm
from rotating?
Are the spray arm holes clogged?
Were the dishes packed too close
together?
Are the filters clogged?
Are the filters fitted correctly in place?
Did you use enough detergent?
Is the salt container cap properly closed?
Did you select a programme with too low
temperature?
Is the rinse aid dispenser empty?
22
Instruction book
Fault
Visible lime deposits or
white film on the dishes.
The dishwasher is noisy. Are the dishes rattling against each other?
Whistling sound when
washing.
The dishes are not quite
dry and are not shiny.
The door is difficult to
close.
Check
Is the salt container empty?
Is the water softener not correctly adjusted?
Is the rinse aid dispenser empty?
Is the rinse aid dispenser adjusted to too
low dosage?
Is the spray arm knocking against the dishes?
This is not a fault, try another brand of
detergent.
Is the rinse aid dispenser empty?
Is the rinse aid dispenser adjusted to too
low dosage?
Have the dishes been left too long inside
the dishwasher?
Is the dishwasher level?
If the indicator lamp for the ended programme cycle is flashing, it is possible
that you can solve the problem your self. When the problem is solved, press
in the On/Off button and the programme continues. If the problem occurs
again, contact your local service centre. If any other lamps flash contact
and inform your local service centre.
Fault
The indicator lamp for the
ended programme cycle is
flashing and a sound signal is emitted.
Check
Is the water tap turned on?
Is the filter inside the inlet hose blocked?
Is the water inlet hose kinked or blocked?
23
Service
Service
Service and spare parts
Servicing and repairs must be carried out by a service company
authorized by the supplier. Use only spare parts supplied by these.
Before calling out an engineer, please check through the details
under the heading ”In the event of a fault” because some faults can
be rectified easily without the need to call out an engineer.
If an engineer is called to resolve a problem listed below or to repair
a fault caused by incorrect installation or mis-use a charge will be
made, even if the appliance is under guarantee.
Note that electrical faults shall always be rectified by a certified
electrician.
Give the appliance’s model designation, PNC-number and F/S-Nr.
(Serienumber) according to the data plate.
24
You can record these details here:
Model designation ............................................................
E/PNC-Nr. ............................................................
F/S-Nr. ............................................................
Purchase date ............................................................
Clear and concise details of the fault:
- What is the fault?
- When does the fault occur?
Information for test centres
The salt container and rinse aid dispenser shall be filled in accordance
with this instruction manual.
Before conducting the measurements the dishwasher shall be operated
for one or two complete cycles using detergent and a clean load.
Service
Test standard:
Rated capacity:
Loading of basket:
Test program:
Detergent (IEC Type B): 9 gram in the dispenser + 5 gram in the pre-
Rinse aid (Type III):
Water pressure:
Waste water outlet:
EN 50242 and EN 60704
6 place settings accordance EN 50242
see chapter ”Loading the dishes”
Eco 50° C
wash dispenser
setting 3
minimum 0,8 bar, maximum 10 bar
Install according to figure below
25
Position- and connection instructions
Position- and connection instructions
Technical specifications
Capacity:
Dimensions: Height
Weight:
Water pressures:
Water
temperature:
Electrical data: Power supply
This appliance complies with the following E.E.C. directives:
– 73/23/EEC, dated 19.02.1973 – low-voltage directive.
– 89/336/EEC, dated 03.05.1989 (incl. amendment
– 92/31/EEC) – directive on electromagnetic compatibility.
6 place settings acc. EN 50242
Width
Depth
Net 22 kg
Minimum
Maximum
Maximum
Fuse
Heating element
Power rating
447 mm
546 mm
493,5 mm
80 kPa (0,8 bar)
1000 kPa (10 bar)
65° C
230 V ~ 50 Hz
10 A
1100 W
1180 W
26
Position- and connection instructions
Installation
Unpacking
Check the dishwasher for transport damage. Never connect a damaged
machine. In the case of damage, please contact your retailer.
Keep all packaging away from children.
Check that the following accessories are supplied with the dishwasher
when you unpack it:
– Afunnel for filling salt (1)
– Elbow for discharge hose (2)
– Hose clip for discharge hose (3)
– Rubber seal (4)
– Restrictor 1/2” (5)
– Protective strip (6)
– Gap strips 2x (7)
– Mount plate (8)
– Guide rods 2x (9)
– Hinges 2x (10)
– Plastic bag with screws, washers
and spacers
2
3
6
1
7
8
Use
This dishwasher is designed solely for
washing household utensils suitable
for washing in a dishwasher. Using it
for other purposes may damage it
and invalidate the guarantee.
4
5
9
10
27
Position- and connection instructions
Position
The machine is basically designed to be built into a cupboard. It is vital to
ensure that the machine is positioned on a horizontal level in order for it to
function properly and so that the door can be properly closed.
Make sure that the shelf for the dishwasher is properly secured
inside the cupboard.
The cupboard must be secured properly onto the wall and the front
edge of the shelf must be level with the sides of the cupboard.
28
Position- and connection instructions
Measurements for fitting a wooden door
Optional doors are available in aluminium and stainless steel. Please
contact your dealer. If you would like a wooden door, drill or mill respectively
as per the diagram below (your wooden door supplier has the requisite
tools), holes for the hinge locking plates (A) diameter 35 mm, predrill the
holes for the hinge brackets (B) diameter 2 mm and guide rods (C) diameter 5 mm. Weight of the door including handle max. 4,7 kg to get good
balance.
A
B
C
29
Position- and connection instructions
Preparing the outer door
Screw the guide rods and hinges on the
door into place using the predrilled holes.
Mount plate
Before installing the dishwasher and
adjusting the door onto the cupboard, put
the mount plate into its correct position on
the shelf.
1. Place the mount plate in the middle
of the cupboard. Mark the holes
for screws and the holes for dismounting the outer door. There is
a middle mark on the plate to
help you.
2x
4x
2. Drill 4 holes with a diameter of
7 mm. The door can be disconnected if necessary, through hole
1 (two holes).
3. Then screw the plate into place
from underneath using the 2 screws
provided, with the washers between.
4. Snap the hinges into the brackets
on the mount plate.
The outer door should be supported
underneath in order to prevent the
hinges from breaking off.
5. Adjust the door to surrounding
doors using screws A, B and C.
A
1
1
B
C
C
30
Mounting the outer door
1. Unscrew the screws on the
mount plate. Lift the plate off
together with the door.
2. Lay the machine down on its
back. Check that none of the
hoses are trapped. Insert the
guide rods into the plastic door
guides.
3. Slot the tabs on the mount plate
into the holes on the front plinth
of the machine and screw the
mount plate into place using
the 2 screws provided.
Position- and connection instructions
Fitting protective and cap
strips
In order to fill the gap between the cupboard and the dishwasher and to protect
the cupboard above from any steam that
comes out of the washer, a self-adhesive
protective strip is attached along the
upper edge of the cupboard and two
gap strips are attached along the edge
of the cupboard.
1. Clean all surfaces where the
strips are to be attached to
ensure better adhesion.
2. Attach the protective strip along
the upper edge of the cupboard.
If it is too long, it can easily be
cut to the right length.
3. Attach the two gap strips along
each side of the cupboard, level
with the front edge of the sides.
Tab
31
Position- and connection instructions
Mounting the dishwasher
1. Put the dishwasher into the cupboard
and screw the mount plate into position
from underneath with 2 screws, with
the washers between.
2. Put the spacers provided at the sides
of the machine and screw the machine
into place in the cupboard.
Check that there is a space between
the cupboard frame and the wooden
door when it is shut.
32
Position- and connection instructions
Water inlet
The dishwasher is equipped with safety features which are to
prevent the water from going back to the fresh water system.
These features are according to current water technical safety
regulations.
The temperature of the water supply should not exceed 65° C and the
pressure should be between 80-1000 kPa (0,8 - 10 bar).
It is important to have a tap or stopcock,
positioned close to the dishwasher and with
easy access. Special mixer taps with dishwasher connections are available, as well
as adaptors for older mixer taps. Connect
the inlet hose to a tap with a 3/4" pipe thread.
If necessary, use the restrictor (1/2”) supplied.
The inlet hose must not be joined onto any
form of extension hose. If it is too short, the
entire hose must be replaced with a longer
highpressure hose, specially designed for
the purpose. The end of the hose, which is
connected to the dishwasher can be turned
in any direction. Loosen the retaining nut,
turn the hose, then retighten the nut.
Check that the nut is tight before the
machine is moved into position.
Use only the inlet hose supplied to
the dishwasher, do not reuse the old
inlet hose.
33
Position- and connection instructions
Water drainage
To protect the dishwasher against water damage it is equipped
with a water safety system. In the event of a fault the drainpump
starts automatically and the remaining water inside the dishwasher
is pumped out.
The water safety system also works when the dishwasher is switched off.
However the dishwasher must be connected electrically.
The discharge hose must not at any
point be higher up than 75 cm over
the surface which the dishwasher is
standing on. If it runs higher, operation
of the dishwasher might be impaired.
The hose should always be routed
at the level which the dishwasher is
standing on, rising up only where it
meets the waste pipe. It is also
important to ensure that the inside
diameter of the hose is not less than
13 mm at any point.
34
Position- and connection instructions
Electrical connection
The dishwasher is supplied with a lead and electrical plug for connection
to a 230 V earthed wall socket, which should be easily accessible and
protected by a 10 Afuse.
Before any work is carried out on the dishwasher, it must be
isolated from the electric mains supply, for example by removing
the plug from the wall socket.
Permanent electrical installation must be carried out by an authorized electrician or competent person.
35
70
71
822 61 10-99
Technical changes possible
Prawo na izmeneniq sohranqetsq
Loading...