FAVORIT 86080 Vi
User manual Dishwasher
2
1
Dear Customer
Thank you for choosing one of our highquality products.
With this appliance you will experience the perfect combination of functional
design and cutting edge technology.
Convince yourself that our appliances are engineered to deliver the best per
formance and control indeed we are setting the highest standards of excel
lence.
In addition to this you find environmental and energy saving aspects as an inte
gral part of our products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfect
ly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep it in a
safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
3 General information and tips
how to avoid damaging the appliance.
2 Environmental information
Contents
Operating Instructions 4
Safety 4
Diagram of appliance 5
Control panel 6
Prior to using for the first time 8
Setting the water softener 8
Adding special salt 10
Filling up with rinse aid 11
Activating/deactivating the acoustic signal 14
In daily use 15
Loading cutlery and dishes 15
Adjusting the height of the upper basket 21
Adding detergent 22
Using 3in1 detergents 23
Selecting the dishwashing cycle (Cycle Table) 25
Starting a dishwashing cycle 27
Setting the Delay Timer 28
Switching off the dishwasher 29
Care and cleaning 30
3Contents
What to do if… 31
Remedying small malfunctions 31
If the dishwashing results are not satisfactory 34
Disposal 35
Technical data 35
Notes for Test Institutes 36
Installation and connection instructions 38
Safety information for the installation 38
Installing the dishwasher 39
Connecting the dishwasher 40
Guarantee/Customer Service 43
Service 47
Operating Instructions4
Operating Instructions
1 Safety
Prior to using for the first time
• Follow the ”Instructions for installation and connection”.
Correct use
• The dishwasher is only intended for washing domestic dishes.
• Additions or modifications to the dishwasher are not permitted.
• Use only special salt, detergent and rinse aid suitable for domestic dishwash
ers.
• Do not put any solvents in the dishwasher. This could cause an explosion.
Child safety
• Keep packaging away from children. There is a risk of suffocation.
• Children often do not recognise the hazards associated with electrical appli
ances. Don’t allow children to use the dishwasher unsupervised.
• Make sure that children and pets don’t climb into the dishwasher. Could en
danger life!
• Dishwasher detergents can cause chemical burns to the eyes, mouth and
throat. Could endanger life! Comply with the safety instructions of the dish
washer detergent manufacturer.
• The water in the dishwasher is not for drinking. Risk of chemical burns.
General safety
• Repairs to the dishwasher are only to be carried out by qualified service engi
neers.
• When the dishwasher is not being used, switch it off and shut off the water
tap.
• Never unplug the appliance by pulling on the cable. Always pull the plug.
• Ensure that the door of the dishwasher is always closed when it is not being
loaded or unloaded. In this way you will avoid anybody tripping over the open
door and hurting themselves.
• Never sit or stand on the open door.
• If the dishwasher is located in a room where there may be a frost, remove the
connection hose from the tap after each use of the dishwasher.
Diagram of appliance
Upper basket spray arm
and floor spray arm
Water hardness
dial
Dispenser
for special salt
Dispenser
for detergent
Dispenser
for rinse aid
5Diagram of appliance
Control panel
Rating plate
Filters
Interior lighting
1 This dishwasher has an internal light that turns on and off when the opening
and closing of the dishwasher’s door occurs.
Internal light equipped with led lamp CLASS 1 in accordance with EN 608251:
1994 + A1:2002 + A2:2001
In case that this light has to be replaced, please contact your local Service Force
Centre.
Control panel6
Control panel
To use the appliance, always open the dishwasher door first.
ON/OFF button
The ON/OFF button is used to turn the dishwasher on and off.
Programme buttons
12 3
Function buttons
Control
indicators
The Programme buttons are used to select the desired dishwashing cycle.
Function buttons: In addition to the preset dishwashing cycle, the following
functions can also be set using these buttons:
Function button 1 Sets the water softener
Function button 2 Activates/deactivates rinse aid inflow when 3in1 on
Function button 3 Activates/deactivates the acoustic signal
The rinse aid inflow is only affected, if the 3in1 function is selected.
7Control panel
Multidisplay
Set delay
timer
Select
3 in1 function
Control
indicators
The multidisplay can indicate:
– the level of hardness to which the water softener is set.
– whether the rinse aid inflow has been activated/deactivated.
– whether the acoustic signal has been activated/deactivated.
– the start delay that has been set.
– the estimated time remaining for the current dishwashing cycle.
– what type of error has occurred with the dishwasher.
The control indicators have the following meanings:
1)
1)
Refill with special salt
Refill with rinse aid
Turn on the tap
Clean the dishwasher's filter system
The door of the dishwasher is open
The upper basket spray arm is jammed
1) These control indicators are never illuminated while a dishwashing cycle is running.
Prior to using for the first time8
Prior to using for the first time
3
If you wish to use 3 in 1 detergent:
– First read the section “Using 3in1 detergents”.
– Do not fill up with special salt or rinse aid.
If you do not use 3in1 detergent, before using for the first time
1. Set the water softener
2. Fill up with special salt for water softeners
3. Fill up with rinse aid
Setting the water softener
The water softener must be set manually and electronically:
3 To avoid scale deposits on the dishes and in the dishwasher, the dishes must be
washed with soft water, i.e. water with a low lime content. The water softener
must be set according to the table to the water hardness in the area where you
live. Your local water company will be able to give you information about the
water hardness in your area.
The dishwasher must be switched off.
Setting manually:
1. Open the dishwasher door.
2. Remove the lower basket from the
dishwasher.
3. Turn water hardness dial on the left wall of
the dishwasher interior to 1 or 2 (see table).
Setting electronically:
1. Press the ON/OFF button.
3 If the only LED indicator illuminated is one that belongs to a programme button,
this means that this dishwashing cycle has been activated. The dishwashing cy
cle must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 2 seconds.
The LED indicators of all the programme buttons that can be selected light up.
2. Press function buttons 2 and 3 simultaneously and keep them pressed.
The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 1.
The LED indicator for function button 1 will flash.
The multidisplay will indicate the hardness setting.
4. Pressing function button 1 increases the hardness setting by 1.
(Exception: hardness setting 1 follows hardness setting 10).
5. When the hardness setting is correct, press the ON/OFF button.
The hardness setting is now saved.
If the water softener is set electronically to “1”, this switches off the control in
dicator for special salt.
9Prior to using for the first time
Water hardness
in
2)
°d
51 70
43 50
37 42
29 36
23 28
19 22
15 18
11 14 1,9 2,5 II 3 3L 3
4 10 0,7 1,8 I/II 2 2L 2
below 4 below 0.7 I
1) The water hardness will only be indicated acoustically if the acoustic signal has been activated.
2) (°d) German degree, measure of the hardness of water
3) [mmol/l] millimol per litre, international unit for water hardness
4) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting
in
mmol/l
9,0 12,5
7,6 8,9
6,5 7,5
5,1 6,4
4,0 5,0
3,3 3,9
2,6 3,2
Range Manual Electronic
3)
IV
III
Setting for
water hardness
2*
1
required
4)
10
9
8
7
6
5*
4
1
no salt
Indicator
on the multi
display
10L
9L
8L
7L
6L
5L
4L
1L 1
Number
of
acoustic
signals
10
9
8
7
6
5
4
1)
Prior to using for the first time10
Adding special salt
To decalcify the water softener, it must be filled up with special salt. Use only
special salt suitable for domestic dishwashers.
If you do not use 3 in1 detergent, fill up with special salt:
– Before using the dishwasher for the first time.
– When the control indicator for special salt is illuminated on the control panel.
1. Open the door and remove the lower
basket.
2. Screw open the lid on the salt dispenser by
turning it anticlockwise.
3. Only when using the dishwasher for the
first time:
Fill the salt dispenser with water.
4. Place the funnel (supplied) over the dis
penser opening.
Fill the dispenser with special salt; the ca
pacity of the dispenser is approx. 1.01.5
kg, depending on the size of the grains. Do
not overfill the dispenser.
3 If water overflows when filling up with special salt, this is completely harmless.
5. Clean away any salt remnants from the dispenser opening.
6. Screw the lid back on in a clockwise direction.
7. Run a dishwashing cycle after filling the salt dispenser with special salt.
This will wash away salt water and salt crystals that have been spilt.
3 Depending on the size of the salt grains, it can take several hours for the salt to
dissolve in the water and for the control indicator for special salt to go out.
Filling up with rinse aid
With rinse aid the rinsing water drains away better and so you get smearfree,
gleaming dishes and clear glasses.
If you do not use 3in1 detergent, fill up with rinse aid:
– Before using the dishwasher for the first time.
– When the control indicator for rinse aid is illuminated on the control panel.
Use only special rinse aid for dishwashers
and no other liquid detergents.
1. Open the door.
The rinse aid compartment is located on
the inside of the dishwasher door.
2. Press the release button on the rinse aid
compartment.
3. Open the cover.
4. Pour rinse aid in slowly right up to the bro
ken “max” line;
this corresponds to a volume of approx.
140 ml when full.
5. Press the lid shut until it clicks into place.
6. Wipe up any spilt rinse aid with a cloth.
Otherwise there will be too much foam
when rinsing.
11Prior to using for the first time
Prior to using for the first time12
Setting the amount of rinse aid required
3 Only change the amount dispensed, if smears, milky spots (reduce the amount)
or dried on water spots (increase the amount) can be seen on glasses and dishes.
(See section “If dishwashing results are not satisfactory”.) The dosage can be set
from 16. The dosage is preset to “4” in the factory.
1. Open the dishwasher door.
2. Press the release button on the rinse aid
compartment.
3. Open the cover.
4. Set the dosage level.
5. Press the lid shut until it clicks into place.
6. If rinse aid has leaked out, wipe it away
with a cloth.
13Prior to using for the first time
Activating rinse aid inflow when 3in1 function is selected
3 If the 3in1 function is not selected, the rinse aid inflow is always activated.
If the 3in1 function is selected due to the use of 3in1 detergent, the rinse aid in
flow is deactivated. If the dishes then do not dry sufficiently, you should reacti
vate the rinse aid inflow (see also section “Using 3in1 detergents”).
1. Press the ON/OFF button.
3 If the only LED indicator illuminated is one that belongs to a programme button,
this means that this dishwashing cycle has been activated. The dishwashing cy
cle must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 2 seconds.
The LED indicators of all the programme buttons that can be selected light up.
2. Press function buttons 2 and 3 simultaneously and keep them pressed.
The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 2.
The LED indicator for function button 2 will flash.
The multidisplay will indicate the current setting:
0d Rinse aid inflow deactivated when 3in1 on (factory setting)
1d Rinse aid inflow activated when 3in1 on
4. Pressing function button 2 activates and deactivates the rinse aid dispensing
function.
5. Once the multidisplay is indicating the required setting, press the ON/OFF but
ton. The setting is now saved.
Prior to using for the first time14
Activating/deactivating the acoustic signal
In addition to the optical display (e.g. indicating the end of the cycle, errors) you
can also choose to set an acoustic signal.
1. Press the ON/OFF button.
3 If the only LED indicator illuminated is one that belongs to a programme button,
this means that this dishwashing cycle has been activated. The dishwashing cy
cle must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 2 seconds.
The LED indicators of all the programme buttons that can be selected light up.
2. Press function buttons 2 and 3 simultaneously and keep them pressed.
The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 3.
The LED indicator for function button 3 will flash.
The multidisplay will indicate the current setting:
0b Acoustic signal deactivated
1b Acoustic signal activated (factory setting)
4. Pressing function button 3 will change the setting.
5. Once the multidisplay is indicating the required setting, press the ON/OFF but
ton. The setting is now saved.
15In daily use
In daily use
Loading cutlery and dishes
1 Sponges, cleaning cloths and any other objects that can absorb water must not
be washed in the dishwasher. Plastic and Tefloncoated dishes and pans tend to
retain water droplets. These dishes and pans therefore do not dry as well as
those made of china and stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans
are not suitable: are of limited suitability:
• Cutlery with wooden, horn, china or
mother of pearl handles
• Plastic items that are not heat re
sistant
• Older cutlery with cement
that is sensitive to temperature
• Dishes or cutlery with glued parts
• Pewter or copper items
• Lead crystal glass
• Steel items that rust
• Wooden boards/platters
• Items made from synthetic materials
• Before loading the dishes, you should:
– Remove the worst of the food residues.
– Soak pans with burnton food residues.
• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation of the spray arms.
– Load bowls, cups, glasses, pans, etc. with the opening downwards so that
water cannot collect in them
– Dishes and items of cutlery must not lie inside one another or cover one an
other
– To avoid damage to glasses, they must not touch one another
– Don’t put small items (e.g. lids) in the baskets for the dishes, but in the cut
lery basket, so that they can’t fall through the holes.
• Only wash stoneware in the dishwasher if it is spe
cifically marked by the manufacturer as being dish
washersafe.
• Glazed patterns may fade if washed very frequently
in the dishwasher.
• Silver and aluminium parts have a tendency to dis
colour during washing. Food remains, e.g. egg white,
egg yolk and mustard often cause discoloration and
staining on silver. Therefore always clean food resi
dues from silver immediately, if it is not to be
washed straight after use.
• Glass can become dull after a large number of wash
es.
In daily use16
Loading cutlery
1 Warning: Sharp knives and other items of cutlery with sharp edges must be laid
in the cutlery rack or in the upper basket to avoid the risk of injury.
To ensure that all items of cutlery in the cutlery basket can be reached by the
water, you should:
1.Place the grid insert on the cutlery
basket
2.Place forks and spoons in the cutlery
basket's grid insert with their han
dles pointing downwards.
For larger utensils, such as whisks, leave off one half of the cutlery grid.
The cutlery basket can be opened out.
Always make sure that you put your hand
around both parts of the twopart handle
when removing it from the dishwasher.
1. Place the cutlery basket on a table or work
surface.
2. Open out the twopart handle.
3. Remove cutlery.
Loading / Unloading lower basket and upper basket
To load and unload, pull out or push in the
upper and lower baskets in the middle us
ing the handle on the front of the basket.
Pots, Pans, Large Plates
Load larger and heavily soiled dishes and
pans in the lower basket.
(Max. diameter for plates 29 cm).
17In daily use
To make it easier to load larger dishes, all
rear plate rests in the lower basket can be
folded down.
In daily use18
Beer glasses and champagne
glasses
Up to four wheat beer glasses, Pils glasses,
etc. can be hung in the beer glass holders
on the lefthand side in the bottom basket.
If necessary, the beer glass holders can be
folded up out of the way.
The beer glass holders can be replaced with
two cup racks supplied as extras, which
also serve as Prosecco glass or champagne
glass holders.
1. Remove beer glass holders by pulling up
wards and pressing lightly on the hooks
from below.
2. Attach cup racks onto the horizontal bars
A or B using the hooks. Press lightly to
snap onto the hooks.
3. Remove the cup racks in the same way as
for the beer glass holders.
4. For wheat beer glasses of normal size at
tach the beer glass holders to horizontal
bar A, for much shorter glasses on B.
The bars that fix the beer glass holders or
cup racks can be removed, if required.
1. Push the bars back using the thumbs (see
the picture).
1 Important: Risk of injury:
Do not take hold of the bars with the hand;
place the hand under the bars on the cut
lery basket for support.
2. Fix the bars again by pushing them
forwards.
19In daily use
In daily use20
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and long,
sharp cutlery in the upper basket.
• Arrange items of crockery on and under
the folding cup racks so that they are
offset from each other and water can
reach all items.
• The cup racks can be folded up out of the
way for tall crockery items.
• Lay or hang wine and brandy glasses in
the slots in the cup racks.
• For glasses with long stems, fold the
glass rack to the right, otherwise fold it
away to the left.
• The row of spikes on the left of the upper
basket is also in two parts and can be
folded away.
Spikes not folded away: place glasses,
mugs etc. in the upper basket.
Spikes folded away: More room for serv
ing dishes.
Adjusting the height of the upper basket
Maximum height of dishes in the
Upper basket Lower basket
with upper basket raised 22 cm 30 cm
with upper basket lowered 24 cm 29 cm
3 The height of the baskets can also be adjusted when they are loaded.
Raising / Lowering the upper basket
1. Pull out the upper basket completely.
2. Holding the upper basket by the handle,
raise it as far as it will go and then lower it
vertically.
The upper basket will latch into the lower
or the upper position.
21In daily use
In daily use22
Adding detergent
Detergents remove the dirt from dishes and
cutlery.
The detergent must be added before the
cycle starts.
1 Only use detergent intended for domestic
dishwashers.
The detergent compartment is located on
the inside of the door.
1. If the lid is closed:
Press the release button.
The lid will spring open.
2. Place the detergent in the detergent dis
penser. The markings indicate the dosing
levels for powder detergents: “20/30” cor
responds to approx.
20/30 ml of detergent.
Follow the manufacturer’s instructions
with regard to dosing and storage.
3. Close the lid and press until it locks into
place.
3 In the case of very heavily soiled dishes, fill
the adjoining compartment (1) with addi
tional detergent. This detergent comes into
use during the prewash cycle.
Concentrated detergents
Today’s detergents for dishwashers are almost exclusively lowalkaline concen
trated detergents with natural enzymes in tablet or powder form.
2 Using 50°C dishwashing cycles in conjunction with these concentrated deter
gents reduces pollution and is good for your dishes, as these dishwashing cycles
are specially matched to the dirtdissolving properties of the enzymes in con
centrated detergents. It is for this reason that using 50 °C dishwashing cycles in
conjunction with concentrated detergents can achieve the same cleaning results
that can otherwise only be achieved using 65 °C cycles.
23In daily use
Detergent tablets
3 Detergent tablets from different manufacturers dissolve at different rates. For
this reason, some detergent tablets do not attain their full cleaning power dur
ing short cycles. Therefore please use dishwashing cycles with prewash when
using detergent tablets.
Using 3in1 detergents
These products are detergents with a combined cleaning, rinsing and salt func
tion.
When the 3in1 function is activated,
– the addition of special salt and rinse aid from the respective dispenser is pre
vented.
– If the salt and rinse aid dispensers are empty, this is not indicated.
– The dishwashing cycles can be up to 30 minutes longer.
3 If you want to use 3in1 detergents, check whether these detergents are suitable
for your water hardness. (Follow manufacturer’s instructions!)
If your water hardness is higher than that recommended by the manufacturer
but you would nevertheless like to use 3in1 detergent, proceed as follows:
• With the 3in1 function selected, set the water softener one hardness setting
lower than when rinsing without 3in1 detergent.
• Fill up the dispenser (if this is empty) with special salt.
The dishwasher remembers the two different settings of the degree of hardness
for rinsing with and without 3in1 function.
If you want to use 3in1 products
1. Press the ON/OFF button.
2. Press the 3IN1 button.
The button indicator lights up: 3in1 function is selected.
Before the start of the dishwashing cycle put 3in1 detergent in the detergent
dispenser.
3 As the rinse aid inflow is automatically switched off when the 3in1 function is
activated, it may come about because of the different quality standards in the
3in1 detergent, that the dishes do not dry sufficiently.
If this happens, proceed as follows (see section “Adding rinse aid”):
• Fill up the dispenser (if this is empty) with rinse aid.
• Set rinse aid dosage to “2” mechanically.
• Activate rinse aid inflow.
In daily use24
If you do not want to use 3in1 products any more
If you want to stop using 3in1 products, please do the following:
• Deactivate the 3in1 function.
• Fill up the dispensers for salt and rinse aid again.
• Switch the water softener to the highest setting and perform up to three nor
mal cycles without loading any dishes.
• Then set the water softener to the water hardness in your area.
If you want to use 4in1 products
When using "4 in 1" detergents that integrate also anti glass corrosion agent
into "3 in 1" formula, please follow the same indication as given for "3 in 1" de
tergents.
Selecting the dishwashing cycle (Cycle Table)
25In daily use
Dishwashing
cycle
AUTOMATIC
(50°65°)
30 MIN
(60°)
2)
3)
Suitable
for:
Dinner service and
cookware
Dishes, excluding
saucepans
Type of
soiling
normally soiled,
driedon food remains
just used, lightly to nor
mally soiled
Programme
sequence
Prewash
Main wash
Intermediate rinse
• •
1 to 2x
• •
• •
Final rinse
Consumption
values
Drying
Length (minutes)
90 110
30
1)
Energy (kWh)
1,0 1,5
0,8
heavily soiled,
INTENSIVE
CARE 70°
Dinner service and
4)
cookware
driedon food remains,
in particular protein
and starch
• •
2x
• •
1,8 2,0
120 130
Dinner service and
cookware, tempera
ECO 50°
5)
turesensitive
crockery
normally soiled • • • • •
130 160
0,95 1,05
Dessert dishes and
coffee service, deli
lightly soiled •
2x
• •
73
0,9
cate glassware
Used dishes that are be
(cold)
6)
All types of dishes
ing stored in the dish
washer and are to be
•
12
< 0,1
washed later.
1) The consumption values were obtained under standardised conditions. They depend on how full the bas
kets for the dishes are. Variations are therefore possible in practice.
2) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The
length of the cycle and water and energy consumption can vary greatly – depending upon the load and
how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically
adjusted to between 50°C and 65°C.
3) When using this cycle, only load the dishwasher half full.
4) During the final rinse, the temperature is increased to 68° for 10 minutes to sanitize e.g. babies’ bottles,
plastic chopping boards or jam jars.
5) Test programme for Test Institutes
6) This cycle does not need any detergent.
Water (litres)
13 25
9
23 25
12 14
15
4
In daily use26
Selecting a programme
When your dishes look like this, select:
an intensive programme.
a normal or energysaving programme.
a short programme (e.g. 30 minute pro
gramme).
27In daily use
Starting a dishwashing cycle
1. Check that the spray arms can turn freely.
2. Turn the water tap on fully.
3. Press the ON/OFF button.
4. Select the desired cycle.
The programme indicator comes on. The remaining time expected for the cycle
will be shown in the multidisplay.
3 During the dishwashing cycle, the remaining time shown in the multidisplay
may be adjusted according to the size of the load, degree of soiling, etc.
5. Close the door. The dishwashing cycle will begin.
A light signal in the form of a dot appears at floor level.
3 If the dishwasher is built in at high level with flush fitting cupboard doors, the
light signal cannot be seen.
The dot shaped light signal is not dangerous. (It is not a laser.) It lights up while
a dishwasher cycle is running and goes out when the cycle ends.
Interrupting or aborting a dishwashing cycle
Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary.
Interrupting the dishwashing programme by opening the dishwasher door
1 Hot steam may escape when the door is opened. There is a risk of scalding.
1. Open the door carefully. The dishwashing cycle will stop.
2. Close the door. The cycle will continue.
Aborting the dishwashing cycle
1. Press function buttons 2 and 3 and keep them pressed.
The LED indicators of all the programme buttons that can be selected light up.
2. Release the function buttons. The dishwashing cycle has been cancelled.
3. If you want to start a new cycle, check whether there is any detergent in the dis
penser.
In daily use28
Setting the Delay Timer
3 With the delay timer you can delay the start of a dishwashing cycle for between
1 and 19 hours.
1. Press the Delay Timer button repeatedly until the multidisplay shows the de
sired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay
Timer indicator is illuminated.
2. Select dishwashing cycle.
3. The time remaining to the start of the cycle is continuously displayed (e. g. 12h,
11h, 10h, … 1h etc.).
To change the time delay:
As long as the cycle has not yet started, you can still change the setting by
pressing the DELAY TIMER button.
Cancelling the time delay:
Press the Delay Timer button repeatedly until the length of the selected cycle
appears in the multidisplay. The selected dishwashing cycle will begin immedi
ately.
To change a dishwashing cycle
As long as the cycle has not yet started, you can still change the dishwashing
cycle. First abort the dishwashing cycle, then reset the time delay, lastly select
the new dishwashing cycle.
Switching off the dishwasher
When the dishwasher cycle has ended, the dot shaped light signal below the
door of the appliance goes out.
If the acoustic signal has been enabled, a continuous tone will sound for approx.
15 seconds at the end of the dishwashing cycle.
If the dishwasher door is not opened, the acoustic signal will repeat after 3 min
utes and again after 6 minutes.
With some dishwashing cycles, the drying fan continues to run even after the
end of the cycle.
1 Carefully open the door. Hot steam may escape.
• Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about
15 minutes before removing them. You also get a better drying result.
• Dishes dry more quickly if you open the door for a moment after the cycle has
ended and then leave it slightly open.
1. Press the ON/OFF button. All display indicators will go out.
2. Turn off the water tap.
Removing the dishes
29In daily use
3 It is normal for the inner door and the dispensers to be damp.
• Empty the lower basket first, then the upper basket. This way you avoid drip
ping water from the upper basket onto dishes in the lower basket.
• The dishwasher's interior light will always be on when the door of the appli
ance is open. Therefore, in order to save energy, you should always close the
door of the dishwasher after having loaded or removed dishes.
Care and cleaning30
Care and cleaning
1
Do not use furniture care products or aggressive cleaners.
• When necessary, clean the dishwasher’s controls with a soft cloth and clean
warm water.
• Occasionally check the internal dispensers, door seal and water inlet filter (if
fitted) for dirt and clean them, if necessary.
Cleaning the filters
3 The filters must be regularly checked and
cleaned. Dirty filters will spoil the wash re
sults.
1. Open the door and remove the lower basket.
2. Turn the handle about ¼ of a turn anticlock
wise (A) and remove the filter system (B).
3. Grasp the grip hole on the fine filter (1) and
remove it from the microfilter (2).
4. Clean all filters thoroughly under running
water.
5. Remove the flat filter (3) from the base of
the washing compartment and clean both
surfaces thoroughly.
6. Reinsert the flat filter.
7. Place the fine filter in the microfilter and fit
the two together.
8. Insert the filter system in place and lock it by
turning the handle clockwise as far as it will
go. Ensure that the flat filter does not pro
trude above the base of the washing com
partment.
1 Under no circumstances may the dishwasher be used without its filters.
What to do if…
Remedying small malfunctions
Before you call the Customer Care Department, please check whether
– you cannot remedy the fault yourself with the help of the following fault ta
ble
or
– whether it is caused by faulty, electrical connections and/or faulty water con
nections.
In these cases the engineer must make you liable for the costs of the Customer
Service intervention even during the warranty period.
In the event of a fault, the light signal at floor level flashes.
If the acoustic signal is activated, warning tones sound if there are faults.
If one of the following fault codes is displayed in the multidisplay during oper
ation:
– Fault codeÅ10 (Problems with water inlet),
– Fault codeÅ20 (Problems with water drainage),
please have a look at the following table.
When the fault is remedied, press the button for the cycle that has started. The
cycle will continue.
With other fault codes (“Å ” followed by a number):
– Abort the dishwashing cycle.
– Switch the appliance off and on again.
– Reset the dishwashing cycle.
If the fault is displayed again, please contact the Customer Care Department
and inform them of the fault code.
31What to do if…
What to do if…32
Malfunction Possible cause Remedy
1 short warning tone, con
tinuously repeated, can be
heard,
the cycle indicator for the se
lected dishwashing cycle is
flashing:
the control indicator
lights up:
fault code
in the multidisplay:
(Problems with water inlet)
2 short warning tones, con
tinuously repeated, can be
heard,
the cycle indicator for the se
lected dishwashing cycle is
flashing,
fault code
in the multidisplay. (Prob
lems with water outflow)
3 short warning tones, con
tinuously repeated, can be
heard,
Fault code Å30 is displayed
in the multidisplay.
1 long warning tone can be
heard,
The control indica
tor is lit.
The control indicator is
lit.
Å10 is displayed
Å20 is displayed
Water tap is blocked with
limescale or faulty.
The tap is turned off. Turn the tap on.
The filter (where present) in the
threaded hose fitting on the
tap is blocked.
Filters in the base of the dish
washer compartment are
blocked.
Water inlet hose
has not been correctly posi
tioned.
The sink outlet is blocked. Clean out sink outlet.
Water drain hose
has not been correctly posi
tioned.
The antiflood system has been
triggered.
The upper basket spray arm is
jammed.
The door of the dishwasher is
open.
Check the water tap and have it
repaired if necessary.
Clean the filter in the threaded
hose fitting.
Cancel the dishwashing cycle
(see chapter: Starting a dish
washing cycle),
clean filters (see chapter:
Cleaning the filters),
then start the dishwashing cy
cle again.
Check the position of the hose.
Check the position of the hose.
First shut off the water tap,
then switch off the appliance
and contact the Customer Care
Department.
Open the door carefully
Hot steam may escape when
the door is opened. There is a
risk of scalding. Arrange the
dishes and cutlery in the bas
kets so that the spray arm
above can rotate freely. Close
the dishwasher door.
Close the dishwasher door.
Malfunction Possible cause Remedy
The control indicator is
lit.
The cycle is not starting.
Rust spots are visible in the
dishwashing compartment.
A whistling noise can be
heard when washing dishes.
The dishwasher interior light
does not come on.
The indicator is there to re
mind you to check the dish
washer’s filters occasionally
and to clean them, if necessary.
It lights up at regular intervals,
regardless of how clean the fil
ters are.
The mains plug is not
plugged in.
A fuse in the house’s wiring
system is defective.
For dishwasher models with a
delay start timer:
A start time has been selected.
The dishwashing compart
ment is made from rustfree
stainless steel. Rust spots in
the dishwashing compartment
are due to rust particles from
external sources (rust particles
from water pipes, pans, cutlery,
etc.). Remove such spots with a
commerciallyavailable clean
ing product for stainless steel.
The whistling is not a cause for
concern.
The mains plug is not
plugged in.
The bulb in the interior light is
faulty.
33What to do if…
The indicator goes out auto
matically at the start of the
next dishwashing cycle.
Plug in mains plug.
Replace fuse.
If the dishes are to be washed
immediately, cancel the delay
start.
Only wash cutlery, dishes and
pans that are suitable for dish
washer use.
Decalcify appliance with com
mercially available agents for
cleaning dishwashers.
If the noises can still be heard
after decalcifying the machine,
use a different brand of deter
gent for washing cutlery and
dishes.
Plug in mains plug.
Contact the Customer Care De
partment.
What to do if…34
If the dishwashing results are not satisfactory
The dishes are still dirty.
• The wrong dishwashing cycle was selected.
• The dishes were loaded is such a way that the dishwashing water did not
reach all items. The baskets for the dishes must not be overloaded.
• Filters in the floor of the dishwasher are not clean or incorrectly inserted.
• Good quality detergent was not used, or too little was used.
• In the case of scale deposits on the dishes: The special salt dispenser is empty
or the water softening system has been incorrectly set.
• The drain hose is incorrectly positioned.
• If at the end of the dishwashing cycle there is still detergent left in the deter
gent dispenser, either the spray arm was jammed or the spray arm jets are
blocked with pollutants in the dishwashing water.
You have the option of removing the spray arms from their fixture for clean
ing (see section “Care and Cleaning”).
The dishes do not dry and are not shining.
• Poor quality rinse aid was used.
• The rinse aid dispenser is empty.
There are smears, streaks, milky spots or a shiny bluish coating on glasses
and dishes.
• Lower rinse aid dosage.
There are dried water drops on the glasses and dishes.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer's cus
tomer advice centre.
Glass corrosion
• Contact the detergent manufacturer's customer advice centre.
Disposal
35Disposal
2
Packaging material
The packaging materials are environmentally friendly and can be recycled. The
plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dis
pose of the packaging materials in the appropriate container at the community
waste disposal facilities.
2 Old appliance
The symbol W on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equip
ment. By ensuring this product is disposed of correctly, you will help prevent po
tential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you
purchased the product.
1 Warning! When your appliance has finished its working life, remove the plug
from the socket. Cut off the cable and plug and dispose of them.
Break the door lock so that the door no longer shuts. This prevents children from
trapping themselves inside and endangering their lives.
Technical data
Capacity: 12 place settings including serving dishes
Permitted water pressure: 0.11.0 MPa (= 10100 N/cm2 = 110 bar )
Electrical connection: See the rating plate on the righthand side of the dishwasher’s in
Dimensions: 820 880 x 596 x 555 (H x W x D in mm)
Max. weight: 45 kg
5
terior door .
Notes for Test Institutes36
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the appliance
fully loaded and using the test cycle (see “Cycle Table”).
Tests in accordance with EN 50242 must be carried out when the salt dis
penser in the water softener and the rinse aid dispenser have been filled with
salt and rinse aid respectively, and using the test cycle (see “Cycle Table”).
Full load: 12 place settings including serving dishes
Amount of detergent re
quired:
Rinse aid setting: 4 (Type III)
5g + 25g (Type B)
Example loading arrangements:
Upper basket
*) If there are cup racks in place on the lefthand side or the cutlery tray is in place, remove them.
*)
37Notes for Test Institutes
Lower basket with cutlery basket
*)
Cutlery basket
*) If necessary, you can remove the cup racks on the lefthand side and/or the beer glass holder.
Installation and connection instructions38
Installation and connection instructions
1 Safety information for the installation
• Only transport the dishwasher in an upright position, otherwise salt water
may run out.
• Before using the dishwasher for the first time, check for any damage caused in
transport. Do not under any circumstances connect an appliance that is dam
aged. In the case of damage, please contact your supplier.
• Never use the dishwasher if the mains cable, water inlet or drain hose are
damaged; or if the control panel, work top or plinth area are damaged such
that the inside of the appliance is freely accessible.
• Always plug the mains plug into a correctly installed shockproof socket.
• Prior to using the appliance for the first time, ensure that the rated voltage
and type of supply on the rating plate match that of the supply where the ap
pliance is to be installed. The fuse rating is also to be found on the rating plate.
• Multiway plugs / connectors and extension cables must not be used. This
could constitute a fire hazard through overheating.
• The dishwasher’s cable must only be replaced by the Customer Care Depart
ment or a registered electrician.
• A water inlet hose with safety valve must only be replaced by the Customer
Care Department.
Installing the dishwasher
• The dishwasher must be installed on a firm floor and adjusted to ensure that it
is stable and level in all directions.
• To compensate for unevenness in the floor and to match the height of the ap
pliance to that of surrounding units, extend the threaded feet using a screw
driver.
• Adjust the rear foot of the appliance using a cordless screwdriver from the
front of the appliance (see installation template).
• The drain hose, inlet hose and mains cable must be laid so that they are able to
move freely within the plinth area, and so that they are not kinked or crushed
when the dishwasher is in position.
• The dishwasher must also be screwed tightly to the work surface or to the ad
joining units. This is essential to ensure the dishwasher does not tip up.
Dishwashers that can be integrated
(see installation template supplied)
Using the installation template supplied split cupboard doors can be easily in
stalled and firmly fitted.
39Installing the dishwasher
Connecting the dishwasher40
Connecting the dishwasher
Connecting to the water supply
• The dishwasher can be connected to cold and hot water supplies up to max.
60°C.
• The dishwasher must not be connected to open hot water appliances or in
stantaneous water heaters.
Permitted water pressure
Lowest permitted water pressure:
0,1 MPa ( = 1 bar = 10 N/cm
Highest permitted water pressure:
1 MPa ( = 10 bar = 100 N/cm
2
)
2
)
Consult your plumber if the water pressure is
less than 0,1 MPa.
If the water pressure is greater than
1 MPa, a pressure reduction valve must be used
(available from your dealer).
Connecting the inlet hose
1 The water inlet hose must not be kinked, crushed or entangled when it is being
connected.
Connect the threaded hose fitting (ISO 2281:2000) on the water inlet hose to a
tap with an external thread (¾ inch). The inlet hose is fitted with either a plastic
or a metal nut:
– Only tighten the nut hand tight.
Then do a visual check for water tightness. (Make sure that the tap is not drip
ping.)
3 So that access to the tap in the kitchen is not restricted by the use of the dish
washer, we recommend installing an additional tap, or fitting a Tbranch to the
existing tap.
1 WARNING! Dangerous voltage
(This does apply to dishwashers with safety
valve).
The electrical cable for the safety valve is in
the doublewalled water inlet hose and is
live.
Therefore do not immerse the water inlet
hose or the safety valve in water.
Water drainage
Drain hose
1 The drain hose must not be kinked, crushed
or entangled.
• Connecting the drain hose:
maximum permitted height above the
bottom edge of the appliance: 60 cm.
41Connecting the dishwasher
Extension hoses
• Extension hoses are available from your
dealer or from our Customer Care Depart
ment. To ensure that the function of the
appliance is not impeded, the internal di
ameter of extension hoses must be 19 mm.
• The total length including extension hoses
must not exceed 4 metres.
Sink outlet connection
• The outlet of the drain hose (ø 19 mm) fits all commonly available sink outlet
types. The outer diameter of the sink outlet connection must be at least 15
mm.
• The drain hose must be fixed to the sink outlet connection using the hose
clamp supplied.
permitted distance
Connecting the dishwasher42
Antiflood system
For protection from water damage, the dishwasher is equipped with a antiflood
system.
In the event of a fault, the safety valve in the water inlet hose immediately in
terrupts the supply of water to the appliance.
Electrical connection
Details about the voltage, type of supply and the fuses required are to be found
on the rating plate. The rating plate is located on the righthand inner edge of
the dishwasher door.
To isolate the dishwasher from the mains, pull out the mains plug.
Important:
– Safety standards require the appliance to be earthed. The manufacturer ac
cepts no liability for failure to observe the above safety precautions.
– The plug must be accessible after the appliance has been installed.
Guarantee/Customer Service
Belgium
DECLARATION OF GUARANTEE TERMS.
Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer serv
ices department will repair this upon request, either during or after the guarantee period. The service life of
the appliance will not, however, be reduced as a result.
This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the
Civil Code. The statutory rights that the consumer has under this legislation are not affected by this declara
tion of guarantee terms.
This declaration does not affect the vendor's statutory warranty to the end user. The appliance is guaranteed
within the context of and in adherence with the following terms:
1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free of charge any defect that
occurs within 24 months from the date the appliance is delivered to the first end user.
These guarantee terms do not apply in the event of use for professional or equivalent purposes.
2. Performing the guarantee means that the appliance is returned to the condition it was in before the defect oc
curred. Defective parts are replaced or repaired. Parts replaced free of charge become our property.
3. So as to avoid more severe damage, the defect must be brought to our attention immediately.
4. Applying the guarantee is subject to the consumer providing proof of purchase showing the purchase and/or
delivery date.
5. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic), synthetic ma
terials and rubber, is the result of inappropriate use.
6. The guarantee cannot be called on for minor faults that do not affect the value or the overall reliability of the
appliance.
7. The statutory warranty does not apply when defects are caused by:
• a chemical or electrochemical reaction caused by water,
• abnormal environmental conditions in general,
• unsuitable operating conditions,
• contact with harsh substances.
8. The guarantee does not apply to defects due to transport which have occurred outside of our responsibility.
Nor will the guarantee cover those caused by inadequate installation or assembly, lack of maintenance or fail
ure to respect the assembly instructions or directions for use.
9. Defects that result from repairs or measures carried out by people who are not qualified or expert or defects
that result from the addition of nonoriginal accessories or spare parts are not covered by the guarantee.
10. Appliances that are easy to transport may be delivered or sent to the consumer services department. Home re
pairs are only anticipated for bulky appliances or builtin appliances.
11. If the appliances are builtin, builtunder, fixed or suspended in such a way that removing and replacing them
in the place where they are fitted takes more than half an hour, the costs that result therefrom will be charged
for. Connected damage caused by these removal and replacement operations will be the responsibility of the
user.
12. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if the repair costs are
considered disproportionate, in agreement with the consumer, the defective appliance may be replaced with
another appliance of the same value.
In this event, we reserve the right to ask for a financial contribution calculated according to the length of time
it has been used.
13. A repair under guarantee does not mean that the normal guarantee period will be extended nor that a new
guarantee period begins.
14. We give a twelve month guarantee for repairs, limited to the same defect.
15. Except in the event where liability is legally imposed, this declaration of guarantee terms excludes any com
pensation for damage outside the appliance for which the consumer wishes to assert his rights. In the event of
legally admitted liability, compensation will not exceed the purchase price paid for the appliance.
43Guarantee/Customer Service
These guarantee terms are only valid for appliances purchased and used in Belgium. For exported appliances,
the user must first make sure that they satisfy the technical conditions (e.g.: voltage, frequency, installation in
structions, type of gas, etc.) for the country concerned and that they can withstand the local climatic and en
vironmental conditions. For appliances purchased abroad, the user must first ensure that they meet the
Guarantee/Customer Service44
qualifications required in Belgium. Nonessential or requested adjustments are not covered by the guarantee
and are not possible in all cases.
Our consumer services department is always at your disposal, even after the guarantee period has expired.
Address for our consumer services department:
ELECTROLUX HOME PRODUCTS BELGIUM
Bergensesteenweg, 719 1502 LEMBEEK
Tel.: 02.363.04.44
Belgium
Electrolux Home Products Belgium
ELECTROLUX SERVICE
Bergensesteenweg 719
1502 Lembeek
Email:
consumer.services@electrolux.be
Consumer services 02/363.04.44 02/363.04.00
Tel.: Fax.:
02/363.04.60
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for
the period specified in the appliance guarantee or otherwise by law. If you move from one of these coun
tries to another of the countries listed below the appliance guarantee will move with you subject to the fol
lowing qualifications:
The appliance guarantee starts from the date you first purchased the appliance which will be evidenced
•
by production of a valid purchase document issued by the seller of the appliance.
•
The appliance guarantee is for the same period and to the same extent for labour and parts as exists in
your new country of residence for this particular model or range of appliances.
•
The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred
to another user.
•
The appliance is installed and used in accordance with instructions issued by Electrolux and is only used
within the home, i.e. is not used for commercial purposes.
•
The appliance is installed in accordance with all relevant regulations in force within your new country of
residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
www.electrolux.com
p t b
Albania +35 5 4 261 450 Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/
Belgien
Èeská republika +420 2 61 12 61 12 Budìjovická 3, Praha 4, 140 21
Danmark +45 70 11 74 00 Sjællandsgade 2, 7000 Fredericia
Deutschland +49 180 32 26 622 Muggenhofer Str. 135, 90429 Nürnberg
Eesti +37 2 66 50 030 Mustamäe tee 24, 10621 Tallinn
España +34 902 11 63 88
France www.electrolux.fr
Great Britain +44 8705 929 929
Hellas +30 23 10 56 19 70 4 Limnou Str., 54627 Thessaloniki
Hrvatska +385 1 63 23 338 Slavonska avenija 3, 10000 Zagreb
Ireland +353 1 40 90 753 Long Mile Road Dublin 12
Italia +39 (0) 434 558500 C.so Lino Zanussi, 26 33080 Porcia (PN)
Latvija +37 17 84 59 34 Kr. Barona iela 130/2, LV1012, Riga
Lietuva +370 5 2780609 Verkių 29, LT09108 Vilnius
Luxembourg +35 2 42 43 13 01 Rue de Bitbourg, 7, L1273 Hamm
Magyarország +36 1 252 1773
Nederland +31 17 24 68 300
Norge +47 81 5 30 222 Risløkkvn. 2 , 0508 Oslo
Österreich +43 18 66 400 Herziggasse 9, 1230 Wien
Polska +48 22 43 47 300 ul. Kolejowa 5/7, Warsaw
Portugal +35 12 14 40 39 39
Romania +40 21 451 20 30 Str. Garii Progresului 2, S4, 040671 RO
Schweiz/Suisse/
Svizzera
Slovenija +38 61 24 25 731
+32 2 363 04 44 Bergensesteenweg 719, 1502 Lembeek
Carretera M300, Km. 29,900
Alcalá de Henares Madrid
Addington Way, Luton, Bedfordshire
LU4 9QQ
H1142 Budapest XIV,
Erzsébet királyné útja 87
Vennootsweg 1, 2404 CG
Alphen aan den Rijn
Quinta da Fonte Edificio Gonçalves Zarco
Q 35
2774 518 Paço de Arcos
+41 62 88 99 111 Industriestrasse 10, CH5506 Mägenwil
Electrolux Ljubljana, d.o.o.
Tržaška 132, 1000 Ljubljana
45Guarantee/Customer Service
Guarantee/Customer Service46
p t b
Electrolux Slovakia s.r.o., Electrolux
Slovensko +421 2 43 33 43 22
Suomi +35 8 26 22 33 00 Konepajanranta 4, 28100 Pori
Sverige +46 (0)771 76 76 76
Türkiye +90 21 22 93 10 25
Россия +7 495 9377837
Domáce spotrebièe SK, Seberíniho 1,
821 03 Bratislava
Electrolux Service, S:t Göransgatan 143,
S105 45 Stockholm
Tarlabaþý caddesi no : 35 Taksim
Istanbul
129090 Москва, Олимпийский
проспект, 16, БЦ „Олимпик“
Service
In the event of technical faults, please first check whether you can remedy the
problem yourself with the help of the operating instructions (section “What to
do if…”).
If you were not able to remedy the problem yourself, please contact the Cus
tomer Care Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number (S No.)
(for numbers see rating plate)
– Type of fault
– Any error messages displayed by the ap
pliance
So that you have the necessary reference numbers from your appliance at hand,
we recommend that you write them in here:
47Service
Model description: .....................................
PNC: .....................................
S No: .....................................
www.electrolux.com
117 995 19/0-00-310806-01 Subject to change without notice
Loading...