EWF 1284 EDW
................................................ .............................................
EN WASHING MACHINE USER MANUAL
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 5
Programmes 6
Consumption values 8
Options 8
Before first use 10
Daily use 10
Hints and tips 13
Care and cleaning 14
Troubleshooting 18
Technical information 19
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
Warning! Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when
it is open.
• If the appliance has a child safety device, we recommend
you activate it.
• Cleaning and user maintenance shall not be made by children without supervision.
electrolux 3
GENERAL SAFETY
• Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
• Do not change the specification of this appliance.
• Obey the maximum load volume of 8 kg (refer to the “Programme chart” chapter).
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
• The operating water pressure (minimum and maximum)
must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)
• The ventilation openings in the base (if applicable) must not
be obstructed by a carpet.
• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
SAFETY INSTRUCTIONS
INSTALLATION
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move
the appliance again you must block the
drum.
• Do not install or use a damaged appli-
ance.
•Do not install or use the appliance where
the temperature is less than 0 °C or
where it is exposed to the weather.
• Obey the installation instruction supplied
with the appliance.
• Make sure that the floor where you install
the appliance is flat, stable, heat resistant
and clean.
• Do not install the appliance where the ap-
pliance door can not be fully opened.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Make sure that there is air circulation be-
tween the appliance and the floor.
• Adjust the feet to have the necessary
space between the appliance and the
carpet.
Electrical connection
Warning! Risk of fire and electrical
shock.
• The appliance must be earthed.
• Make sure that the electrical information
on the rating plate agrees with the power
supply. If not, contact an electrician.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the appliance power supply cable
need to be replaced, this must be carried
out by our Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
4 electrolux
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains
plug.
• Do not touch the mains cable or the
mains plug with wet hands.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Make sure not to cause damage to the
water hoses.
• The appliance is to be connected to the
water mains using the new supplied
hose-sets. Old hose sets must not be
reused.
• Before you connect the appliance to new
pipes or pipes not used for a long time,
let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
USE
Warning! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
• Use this appliance in a household environment.
• Do not change the specification of this
appliance.
• Obey the safety instructions on the detergent packaging.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Do not touch the glass of the door while
a programme operates. The glass can be
hot.
• Make sure that you remove all metal objects from the laundry.
• Do not put a container to collect possible
water leakage under the appliance. Contact the Service to ensure which accessories can be used.
CARE AND CLEANING
Warning! Risk of injury or damage to
the appliance.
• Before maintenance, deactivate the appliance and disconnect the mains plug
from the mains socket.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
DISPOSAL
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and pets to get closed in the appliance.
PRODUCT DESCRIPTION
1 2 3
CONTROL PANEL
1 2 3 4
electrolux 5
Worktop
1
Detergent dispenser
2
Control panel
3
Door handle
4
Rating plate
5
4
5
Drain pump filter
6
Feet for the appliance level
7
FIXING PLATE KIT (4055171146)
Available from your authorized dealer.
If you install the appliance on a plinth, se-
6
cure the appliance in the fixing plates.
Follow the instructions supplied with the kit.
7
5 gömlek
Spor
giysileri
Perde
Kot
kumaşlar
Sıkma
Bo şaltma
Durulama
Programme knob
1
Spin reduction touchpad
2
(Sıkma)
Temperature touchpad
3
(Sıcaklık)
Display
4
Prewash touchpad
5
(Ön yıkama)
Delay start touchpad
6
(Gecikmeli başlatma)
Pamuklular
Yünlü/Elde yıkama
İpekliler
Yorgan
Pamuklular Eco
Sentetikler
Hassas giysiler
Sıcaklık
40°
60°
90°
20°
30°
800
1000
1200
400
Sıkma
TimeManager
Ön
yıkama
Kolay ütü
Gecikmeli
latma
baş
Ekstra
durulama
şBa lat/Durdur
6
7
8
910
5
Extra rinse touchpad
7
(Ekstra durulama)
Easy iron touchpad
8
(Kolay ütü)
Start pause touchpad
9
(Başlat/Durdur)
Time Manager touchpads
10
6 electrolux
DISPLAY
AB
ED
PROGRAMMES
Programme
Temperature range
Pamuklular
90°C — Cold (
Pamuklular Eco
60 °C – 40 °C
Sentetikler
60 °C— Cold (
Hassas giysiler
40 °C - Cold (
Yünlü/Elde yıkama
40 °C – Cold (
Ipekliler
30 °C
Yorgan
60 °C – 30 °C
Durulama
Boşaltma
Sıkma
Kot kumaşlar
60 °C - Cold (
)
)
)
)
)
A) The time area:
C
– Programme time.
– The alarm codes. Refer to the chapter
“Troubleshooting” for their description.
–
The level of the Time Manager
.
B) The Delay Start indicator.
C) The Child Lock indicator.
D) The Door Lock indicator:
– It is on, you cannot open the door.
– It is off, you can open the door.
– It flashes, you cannot open the door.
Wait for some minutes until the indicator is off.
E) Washing phase indicators.
Type of load and soil
Maximum load, Maximum spin
White cotton and coloured cotton. Normal soil and light soil.
8 kg, 1200 rpm
1)
White cotton and colour-fast cotton. Normal soil.
8 kg, 1200 rpm
Synthetic items or mixed fabric items. Normal soil.
3 kg, 1200 rpm
Delicate fabrics as acrylics, viscose, polyester items. Normal
soil.
3 kg, 1200 rpm
Machine washable wool, hand washable wool and delicate
fabrics with «hand washing» care symbol.
2 kg, 1200 rpm
Special programme for silk and mixed synthetic items.
2 kg, 800 rpm
Special programme for one synthetic blanket, duvet, bedspread and so on.
2 kg, 800 rpm
To rinse and spin the laundry. All fabrics.
8 kg, 1200 rpm
To drain the water in the drum. All fabrics.
8 kg
To spin the laundry and to drain the water in the drum. All
fabrics.
8 kg, 1200 rpm
Items in denim and jersey. Also for items in dark colors.
8 kg, 1200 rpm
electrolux 7
Programme
Temperature range
Perde
40 °C - Cold (
Spor giysileri
30 °C
5 gömlek
30 °C
Special programme for curtains. The prewash phase acti-
)
vates automatically.
2 kg, 800 rpm
Synthetic and delicate items. Light soil or items or items to
refresh.
2.5 kg, 800 rpm
Synthetic and mixed fabric items. Light soil and items to
freshen up.
For 5 - 6 shirts.
Type of load and soil
Maximum load, Maximum spin
2)
800 rpm
1) Standard programmes for the Energy Label consumption values.
According to regulation 1061/2010, these programmes are respectively the «Standard 60 °C cotton programme»
and the «Standard 40 °C cotton programme». They are the most efficient programmes in terms of combined
energy and water consumptions for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected programme.
2) Do not use any detergent for prewash phase to rinse only with water.
Programme options compatibility
Programme
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■
■ ■ ■
■ ■
■ ■ ■ ■ ■
■
■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■
■ ■ ■
■ ■ ■
8 electrolux
CONSUMPTION VALUES
At programme start the display shows the duration programme for the maximum
load capacity.
During the washing phase the programme duration is automatically calculated and
can greatly be reduced if the laundry load is lower than the maximum load capacity
(e.g. Cotton 60°C, maximum load capacity 8 kg, the programme duration exceeds 2
hours; real load 1 kg, the programme duration don’t reach 1 hour).
When the appliance is calculating the real programme duration a dot blinks in the
display.
The data of this table are approximate. Different causes can change the data: the
quantity and type of laundry, the water and ambient temperature.
Programmes Load
(Kg)
Pamuklular 60
°C
Pamuklular 40
°C
Sentetikler 40 °C 3 0.40 45 100 35
Hassas giysiler
40 °C
Yünlü/Elde yıka-
ma 30 °C
Standard cotton programmes
Standard 60 °C
cotton
Standard 60 °C
cotton
Standard 40 °C
cotton
Off Mode (W) Left On Mode (W)
0.48 0.48
The information given in the chart above are in compliance with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC.
1) At the end of spin phase.
Energy con-
sumption
(kWh)
8 1.56 65 240 53
8 0.90 65 236 53
3 0.52 50 80 35
2 0.31 48 60 30
8 1.02 56 242 53
4 0.78 44 211 53
4 0.59 44 191 53
Water con-
sumption (li-
tre)
Approximate
programme
duration (mi-
nutes)
Remaining
moisture
(%)
1)
OPTIONS
TEMPERATURE
Set this option to change the default temperature.
Indicator
The display shows the set temperature.
SPIN
With this option you can change the default
spin speed.
The indicator of the set speed comes on.
= cold water.
Additional spin options:
No Spin
• Set this option to deactivate all spin pha-
ses. Only the drain phase is available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for
some washing programmes.
electrolux 9
Rinse Hold
• Set this option to prevent the laundry
creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the
laundry creases.
• The door stays locked.
• You must drain the water to unlock the
door.
To drain the water refer to ‘At the end
of the programme’.
PREWASH
With this option you can add a prewash
phase to a washing programme.
Use this option for heavy soil.
When you set this option the programme
duration increases.
The related indicator comes on.
DELAY START
With this option you can delay the start of a
programme from 30 minutes to 20 hours.
The display shows the related indicator.
EXTRA RINSE
With this option you can add some rinses
to a washing programme.
Use this option for persons allergic to detergents and in areas where the water is soft.
The related indicator comes on.
EASY IRON
The appliances carefully washes and spins
the laundry to prevent the creases.
The appliance decreases the spin speed,
uses more water and adapt the programme
duration to the type of laundry.
The related indicator comes on.
TIME MANAGER
When you set a washing programme, the
display shows the default duration.
Press
or to decrease or increase the
programme duration.
The Time Manager is available only with the
programmes in the table.
Time Manager compatibility
indicator
1)
2)
1) Shortest: to freshen the laundry.
2) Default level.
■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
CHILD LOCK
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate the option,
press
the indicator
and at the same time until
comes on/goes off.
You can activate this option:
• After you press
, the options and the
programme knob are locked.
• Before you press
: the appliance can-
not start.
PERMANENT EXTRA RINSE
With this option you can permanently have
an extra rinse when you set a new programme.
• To activate/deactivate this option
press
the indicator
and at the same time until
comes on/goes off.
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals, press
and at the same time
for 6 seconds.
If you deactivate the acoustic signals,
they continue operate when the appliance has a malfunction.
10 electrolux
BEFORE FIRST USE
1. Put 2 litre of water in the detergent
compartment for washing phase. This
activates the drain system.
2. Put a small quantity of detergent in the
compartment for washing phase.
DAILY USE
LOADING THE LAUNDRY
USING DETERGENT AND ADDITIVES
3. Set and start a programme for cotton
at the highest temperature without
laundry. This removes all possible dirt
from the drum and the tub.
1. Open the appliance door.
2. Put the laundry in the drum, one item
at a time. Shake the items before you
put them in the appliance. Make sure
not to put too much laundry in the
drum.
3. Close the door.
Caution! Make sure that no laundry
stays between the seal and the door.
There is a risk of water leakage or
damage to the laundry.
• Measure out the detergent and the fabric
conditioner.
• Carefully close the detergent drawer.
Detergent compartment for prewash phase.
Detergent compartment for washing phase.
Compartment for liquid additives (fabric conditioner, starch).
Flap for powder or liquid detergent.
Liquid or powder detergent
1.
electrolux 11
2.
A
3.
4.
B
• Position A for powder detergent (factory setting).
• Position B for liquid detergent.
When you use the liquid detergent:
– Do not use gelatinous or thick liquid detergents.
– Do not put more liquid then the maximum level.
– Do not set the prewash phase.
– Do not set the delay start.
SETTING A PROGRAMME
1. Turn the programme knob and set the
programme:
–
The indicator
flashes.
STARTING A PROGRAMME WITHOUT
DELAY START
Press
• The indicator
– The display shows the level of the
Time Manager, the programme dura-
•
tion and the indicators of the phases
of the programme.
• The programme starts, the door is locked
2. If necessary, change the temperature
and the spin speed or add available op-
• The drain pump can operate for a short
tions. When you activate an option, the
indicator of the set option comes on.
If you set something incorrect, the display shows the message Err.
1
2
:
stops to flash and stays
on.
The indicator
starts to flash on the
display.
and the display shows the indicator
time when the appliance fills water.
.
12 electrolux
After approximately 15 minutes from
the start of the programme:
• The appliance adjusts automatically
the programme duration agree with
the laundry load.
• The display shows the new value.
STARTING A PROGRAMME WITH
DELAY START
•
Press
again and again until the display shows the delay you want to set.
The related indicator comes on the display.
•Press
:
– The appliance starts the countdown.
– When the countdown is completed,
the programme starts automatically.
You can cancel or change the set of
the delay start before you press
.
To cancel the delay start:
1. Press
2.
Press
Press
to set the appliance to pause.
until the display shows ’.
again to start the programme
immediately.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before
they operate.
1. Press
. The indicator flashes.
2. Change the options.
3. Press
again. The programme con-
tinues.
CANCELLING A PROGRAMME
1.
Turn the programme knob to
to
cancel the programme and to deactivate the appliance.
2. Turn the programme knob again to activate the appliance. Now, you can set
a new washing programme.
The appliance does not drain the water.
OPENING THE DOOR
While a programme or the delay start operates, the appliance door is locked and the
display shows the indicator
.
Caution! If the temperature and level
of the water in the drum are too high,
you cannot open the door.
Open the appliance door when the
delay start operates:
1. Press
2.
Wait until the door lock indicator
to pause the appliance.
goes off.
3. You can open the door.
4. Close the door and press
again.
The delay start continues to operate.
Open the appliance door when the
programme operates:
1.
Turn the programme knob to
to de-
activate the appliance.
2. Wait for some minutes and then open
the appliance door.
3. Close the appliance door.
4. Set the programme again.
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is acti-
vated).
•
In the display
• The indicator
•
The door lock indicator
comes on.
goes off.
goes off.
• Remove the laundry from the appliance.
Make sure that the drum is empty.
• Keep the door ajar, to prevent the mildew
and odours.
• Close the water tap.
•
Turn the programme knob to
to deac-
tivate the appliance.
The washing programme is completed,
but there is water in the drum:
– The drum turns regularly to prevent the
creases in the laundry.
–
The door lock indicator
is on. The
door stays locked.
– You must drain the water to open the
door.
To drain the water:
1. If necessary, decrease the spin
speed. if you set
, the appli-
ance only drains.
2. Press
. The appliance drains the
water and spins.
3. When the programme is completed
and the door lock indicator
goes
off, you can open the door.
4.
Turn the programme knob to
to
deactivate the appliance.
electrolux 13
The appliance drains and spins automatically after approximately 18 hours
(except for Wool programme).
STAND-BY
Some minutes after the end of the washing
programme, if you do not deactivate the
appliance, the energy saving status activates.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on
the laundry care labels.
• Do not wash together white and coloured
items.
• Some coloured items can discolour with
the first wash. We recommend that you
wash them separately for the first times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn inside out multilayered fabrics, wool
and items with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy soil
stains.
• Be careful with the curtains. Remove the
hooks or put the curtains in a washing
bag or pillowcase.
•Do not wash in the appliance :
– Laundry without hems or with cuts
– Underwired bras.
– Use a washing bag to wash small
items.
• A very small load can cause balance
problems with the spin phase. If this occurs, adjust manually the items in the tub
and start the spin phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you remove these
stains before you put the items in the appliance.
Special stain removers are available. Use
the special stain remover that is applicable
to the type of stain and fabric.
The energy saving status decreases the energy consumption when the appliance is on
the stand by.
• All indicators and the display go off.
•
The indicator
• Press one of the options to deactivate
the energy saving status.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially made for washing machines.
• Do not mix different types of detergents.
• To help the environment, do not use
more than the correct quantity of detergent.
• Obey the instructions that you find on the
on packaging of these products.
• Use the correct products for the type and
colour of the fabric, the programme temperature and the level of soil.
• If your appliance has not the detergent
dispenser with the flap device, add the
liquid detergents with a dosing ball.
ECOLOGICAL HINTS
• Set a programme without the prewash
phase to wash laundry with normal soil.
• Always start a washing programme with
the maximum load of laundry.
• If necessary, use a stain remover when
you set a programme with a low temperature.
• To use the correct quantity of the detergent, check the water hardness of your
domestic system
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a
water softener for washing machines. In
areas where the water hardness is soft it is
not necessary to use a water softener.
To know the water hardness in your area,
contact your local water authority.
Use the correct quantity of the water softener. Obey the instructions that you find on
the packaging of the product.
flashes slowly
14 electrolux
CARE AND CLEANING
Warning!
Before maintenance, disconnect the appliance from the mains supply.
EXTERNAL CLEANING
Clean the appliance only with soap and
warm water. Fully dry all the surfaces.
Caution! Do not use alcohol, solvents
or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a
water softener for washing machines.
Regularly examine the drum to prevent
limescale and rust particles.
DOOR SEAL
To remove rust particles use only special
products for washing machine. Do this separately from the laundry wash.
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is
possible that some detergent stays in the
drum. Make regularly a maintenance wash.
To do this:
• Remove the laundry from the drum.
• Set the cotton programme with the highest temperature with a small quantity of
detergent.
Regularly examine the seal and remove all
objects from the inner part.
CLEANING THE DETERGENT DISPENSER
1.
1
2
2.
3. 4.
CLEANING THE DRAIN FILTER
Warning! Do not clean the drain filter if
the water in the appliance is hot.
1.
electrolux 15
2.
11
2
3. 4.
2
1
16 electrolux
5.
1
2
7. 8.
9.
6.
1
2
CLEANING THE INLET HOSE AND THE VALVE FILTER
1.
2.
1
2
3
3. 4.
20°
electrolux 17
45°
EMERGENCY DRAIN
Because of a malfunction, the appliance
cannot drain the water.
If this occurs, do steps (1) through (9) of
'Cleaning the drain filter'.
If necessary, clean the pump.
When you drain the water with the emergency drain procedure, you must activate
again the drain system:
1. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2. Start the programme to drain the water.
FROST PRECAUTIONS
If the appliance is installed in an area where
the temperature can be less than 0° C, remove the remaining water from the inlet
hose and the drain pump.
1. Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Remove the water inlet hose.
4. Put the two ends of the inlet hose in a
container and let the water flow out of
the hose.
5. Empty the drain pump. Refer to the
emergency drain procedure.
6. When the drain pump is empty, install
the inlet hose again.
Warning! Make sure that the
temperature is more than 0 °C before
you use the appliance again.
The manufacturer is not responsible for
damages caused by low temperatures.
18 electrolux
TROUBLESHOOTING
The start of the appliance does not occur or
it stops during operation.
First try to find a solution to the problem (refer to the table). If not, contact the service
centre.
With some problems, the acoustic
signals operate and the display shows
an alarm code:
•
- The appliance does not fill with
water.
Problem Possible solution
The programme does not
start.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of count-
Deactivate the Child Lock function if it is on.
The appliance does not fill
with water.
Make sure that the pressure of the water supply is not too low. For
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose and the filter of the valve are
Make sure that the inlet hose has no kinks or bends.
Make sure that the connection of the water inlet hose is correct.
The appliance does not
drain the water.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if neces-
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain
Set the drain programme if you set an option which ends with water
The spin phase does not
operate or the washing cycle lasts longer than usually.
Make sure that the drain filter is not clogged. Clean the filter, if neces-
Adjust manually the items in the tub and start the spin phase again.
Make sure that the mains plug is connected to the mains socket.
down.
Make sure that the water tap is open.
this information, contact your local water authority.
not clogged. Refer to “Care and cleaning”.
Make sure that the sink spigot is not clogged.
sary. Refer to 'Care and cleaning'.
phase.
in the tub.
Set the spin programme.
sary. Refer to 'Care and cleaning'.
This problem may be caused by balance problems.
•
- The appliance does not drain the
water.
•
- The appliance door is open or not
closed correctly. Please check the door!
•
- The mains supply is unstable.
Wait until the mains supply is stable.
Warning! Deactivate the appliance
before you do the checks.
electrolux 19
Problem Possible solution
There is water on the floor. Make sure that the couplings of the water hoses are tight and there is
Make sure that the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of
You cannot open the appliance door.
Set the drain or the spin programme if there is water in the drum.
The appliance makes an
unusual noise.
Make sure that the packaging and/or the transit bolts are removed.
Add more laundry in the drum. The load may be too small.
The appliance fills with wa-
ter and drain immediately.
The washing results are not
satisfactory.
Use special products to remove the stubborn stains before you wash
Make sure that you set the correct temperature.
Decrease the laundry load.
After the check, activate the appliance. The
programme continues from the point of interruption.
not water leakages.
it.
Make sure that the washing programme is finished.
Make sure the levelling of the appliance is correct. Refer to 'Installation'.
Refer to 'Installation'.
Make sure that the drain hose is in the correct position. The hose
may be too low.
Increase the detergent quantity or use a different detergent.
the laundry.
If the display shows other alarm codes. Deactivate and activate the appliance. If the
problem continues, contact the Service.
If the problem occurs again, contact the
Service.
TECHNICAL INFORMATION
Dimensions Width / Height / Depth 600 / 850 / 522 mm
Total depth 540 mm
Electrical connection: Voltage
Level of protection against ingress of solid particles and moisture
ensured by the protective cover, except where the low voltage
equipment has no protection against moisture
Water supply pressure Minimum 0,5 bar (0,05 MPa)
Water supply
Maximum load Cotton 8 kg
Spin speed Maximum 1200 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
1)
Overall power
Fuse
Frequency
Maximum 8 bar (0,8 MPa)
Cold water
230 V
2200 W
10 A
50 Hz
IPX4
www.electrolux.com/shop 132916970-A-102013
Loading...