AEG-Electrolux EW1230I User Manual
INFO
BEDIENUNGSANLEITUNG
GEBRUIKSAANWIJZING
MODE D'EMPLOI
MANUAL DE INSTRUCCIONES
INSTRUCTION MANUAL
WASCHVOLLAUTOMAT EW 1230 I
WASAUTOMAAT EW 1230 I
LAVE - LINGE EW 1230 I
LAVADORA EW 1230 I
WASHING MACHINE EW 1230 I
CONTENTS
Warnings ..........................Page 79
Installation .........................Page 80
Unpacking..........................Page 80
Positioning..........................Page 80
Water inlet..........................Page 80
Water drainage ........................Page 81
Electrical connection .......................Page 81
Levelling ..........................Page 81
Building-in ..........................Page 82
Use............................Page 83
Control panel .........................Page 83
Washing hints.........................Page 84
Detergents and additives .....................Page 85
Washing programmes ......................Page 86-87
Wash code symbols .......................Page 88
Operating sequence .......................Page 89
Maintenance .........................Page 90
Bodywork ..........................Page 90
Detergent dispenser drawer.....................Page 90
Drain filter ..........................Page 90
Water inlet filter ........................Page 90
Something not working? .....................Page 91
TECHNICAL SPECIFICATIONS
DIMENSIONS Height 82 cm
Width 60 cm
Depth 54 cm
POWER SUPPLY VOLTAGE/FREQUENCY 220-230V / 50 Hz
TOTAL POWER ABSORBED 2200 W (10A)
WATER PRESSURE Minimum 15 N/cm
Maximum 80 N/cm
2
2
MAXIMUM RECOMMENDED Cotton, linen 5 kg
LOAD Synthetics, delicate fabrics 2 kg
Wool 1 kg
SPIN SPEED Maximum 1200 rpm
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
78
WARNINGS
You must read the whole of this instruction book
before you use the appliance. Follow the advice
carefully.
Keep the book for future reference. If you sell or
give away the appliance, make sure that the book
is passed to the new owner.
The following warnings are provided in the interest of overall safety. You must read them before
the appliance is installed or used.
■
This appliance is designed to be used by adults.
Children should not be allowed to touch the controls or play with the product.
■
It is dangerous to modify the specifications of this
appliance in any way.
■
This appliance is heavy. Care should be taken
when moving it.
■
All packaging and transit bolts must be removed
before the appliance is used. Serious damage
may occur if this is not done.
■
Any plumbing work required to install this appliance should be carried out by a qualified plumber
or competent person.
■
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
■
Make sure that the appliance does not stand on
its electrical supply cable.
■
If the machine is situated on a carpeted floor,
please adjust the feet to ensure that air can circulate freely.
■
Always unplug the appliance and turn off the
water after use.
■
Do not overload the appliance.
■
Only wash fabrics which are designed to be
machine washed. If in doubt, follow the instructions you find on the label of the item itself.
■
Make sure that all pockets are empty. Hard, sharp
objects such as coins, safety pins, nails, screws or
stones can cause extensive damage.
■
Do not machine wash fabrics which are saturated
with petroleum products. If volatile cleaning fluids
have been used, make sure that they are thoroughly removed from the fabric before it is placed
in the appliance.
■
Use only the recommended quantities of fabric
conditioner.
■
Leave the porthole door slightly ajar between
washes to preserve the door seal.
■
Before you open the door of the machine check
that the water has drained. Do not open the door if
you can still see water.
■
Pets and small children may climb into washing
machines. Check your appliance each time before
use.
■
The glass door becomes very hot during washing
cycle. Keep children away from the appliance
while it is in use.
■
You should not attempt to repair the machine
yourself. Repairs carried out by inexperienced or
unqualified persons may cause injury and/or more
serious faults to the machine.
■
This product should be serviced by an authorised
Service Centre only, and only genuine spare parts
should be used.
■
When disposing of your old washing machine, the
electric cable must be cut off and the door catch
must be made unusable.
79
INSTALLATION
Unpacking
All transit bolts and packing must be removed before
using the machine.
You are advised to keep all packing for re-use in case
you move house and the machine has to be transported again.
Proceed as follows:
Using a spanner remove
the screw on the right at
the rear of the machine.
Carefully lay the machine on its back making
sure that the hoses are
not squashed.
Place between machine
P0255
Remove the polystyrene base and take off the bottom
panel by unscrewing the central screw.
Carefully remove the right polythene bag.
P0457
Carefully take off the central and left polythene bags.
Re-fit the bottom panel using the 4 screws supplied
with the hinges and the previously removed screw.
P0016
Set the machine upright and unscrew the two remaining rear screws.
and bottom one of the
polystyrene angle packings.
P0015
P0453
Positioning
Position the machine on a firm level surface.
The machine must not touch the wall or other furni-
ture.
It is assumed that the tap, drainage point and socket
are within easy reach of the machine hoses and
power supply cable. If not, you are advised to call
your fitter in order to move the tap and/or drainage
point and/or socket.
P0023
Water inlet
Connect the water inlet hose to a tap with a 3/4" gas
thread spout.
The inlet hose is provided with a water stop
device, which protects
against damage caused
by water leaks in the fill
hose which could develop due to natural ageing
A
P0271
Should this occur, turn the water tap off and refer to
your Service Agent to replace the hose.
P0021
replace it completely with a longer high pressure hose
specifically designed to solve problems of this type.
of the hose. This fault is
shown by a red sector in
the window «A».
The other end of the inlet
hose connected to the
machine can be turned in
any direction. Simply loosen the fitting, rotate the
hose and retighten.
The inlet hose must not
be extended. If it is too
short and you do not
wish to move the tap,
P0256
P0020
Slide out the 3 plastic spacers and plug the 3 holes
with the 3 plastic plugs which you can find on the
back of the machine.
80
Water drainage
The end of the drain hose can be positioned in three
ways:
Over the edge of a basin at a height of between 60
and 90 cm.
To keep the drain hose
spout bent, use the special plastic hose guide
supplied with the machine. Secure it to the wall
with a hook, for example,
or to the tap by means of
a piece of string, to pre-
P0235
cycle thus causing floods.
In a basin drainpipe branch: the branch must be
above the basin siphon so that the end of the hose is
at least 60 cm from ground level.
Directly in a drainpipe: you are advised to use a
vertical 65 cm high pipe; in any case it should never
be shorter than 60 cm or longer than 90 cm.
The end part of the drain hose must always be ventilated, i.e. the internal diameter of the pipe must be
wider than the external diameter of the drain hose.
The drain hose can be extended up to a maximum
length of 180 cm. Use an extension with an internal
diameter at least equal to the diameter of the original
hose and a suitable fitting. The hose extension will
run along the floor and only the part near the drainage point will be raised.
vent the drain hose
moving during rinsing
Electrical connection
Before plugging the appliance into the wall socket,
make sure that:
1. the mains voltage corresponds to the voltage given
in the technical specifications;
2. the meter, fuses, mains power supply and wall
socket can all take the maximum load required.
Make sure that the socket and plug are compatible
without having to use any type of adapter. If necessary, have the domestic wiring system socket replaced.
The electric cable must not be extended. If it is too
short and you do not wish to move the socket, replace it completely with a longer cable.
Safety standards require the appliance to be
earthed.
The Manufacturer accepts no liability for failure to
observe the above safety precautions.
Levelling
Position the appliance and level it by tightening or
loosening one or two of the adjustable feet. Ensure
that the machine is resting securely with all four feet
on the ground. Once the machine has been levelled,
tighten up the lock nuts on all feet with the aid of a
screwdriver.
P0254
P0509
81
Loading...