1
Frozen food must not be re-frozen once it
has been thawed out.
Manufacturer’s storage recommendations
should be strictly complied with.
The lollies can cause frost burns if consumed right away from the freezer.
Do not place carbonate or fizzy drinks in the
freezer as these may explode.
Whenever there is a need for discarding an
old freezer make sure to:
Take off the doors in order to prevent
children trapped inside.
Have the gas from the cooling system
recovered before making it to scrap iron.
Warnings for your safety
Warnings for your safety. Carefully read these
instructions before installing and using the
machine.
This freezer is designed to be operated by
adults. Children should not be allowed to tamper with the controls or play with the product.
Any electrical work required to install the
appliance should be carried out by a qualified
electrician or competent person.
This appliance is heavy. Care should be taken
when moving it.
Make sure that the cable is not trapped underneath the appliance, nor touches the motor.
Repairs carried out by inexperienced persons
may cause injuries or serious malfunctioning.
Refer to the nearest Authorized Dealer.
Make sure the rear part of the appliance stands
against a wall as there are working parts which
heat up and should not be of easy access.
Make sure that there is a continous and adequate ventilation as a failor to do so will result
in component failure and possible food loss.
The appliance should be left for at least 4 hours
after installation before it is turned on ill order
to allow the refrigerant to settle.
This product must be serviced only by an authorized NETWORK SERVICE CENTRE, and
only genuine SPARE PARTS must be employed.
Before cleaning or reparing the appliance,
make sure it is unplugged.
It is dangerous to alter the specifications or
modify this product in any way.
These domestic refrigerators are designed to
be used specifically for the storage and conservation of food.
DO NOT USE SHARP INSTRUMENTS to
scrap off frost or ice. Frost may be removed by
using a plastic scraper. (See defrosting instructions).
2
Index
Warnings for your safety pag. 1
Installation pag. 3
Changing the opening directions
of the doors and panelling pag. 4 - 5
Regulation and Control pag. 6
How to use your
Refrigerator-Freezer pag. 7
Maintenance of your
Refrigerator-Freezer pag. 8 - 9
Something not working pag. 10 - 11
Normal noises when
functioning pag. 12
Guarantee, Service
and Spare Parts pag. 13
Tecnical Features pag. 14
3
Installation
PPoossiittiioonniinngg
• Place the refrigerator away from direct sunlight
and heat sources.
• Maintain recommended ventilation - see Fig. 1.
• Make sure the refrigerator is accurately levelled
turning the adjustable feet in order to avoid vibrations and noises. Fig. 2.
• This is a built in design to be aligned with other
furniture.
• The appliance musb be located in places of maximum temperature as follows:
+ 38°C for ST Class, classification on identifiying
plate.
If the temperature are higher than these both
above mentioned, the functions of appliance
could result reduced.
CClleeaanniinngg tthhee iinntteerriioorr
• Do not use alcohol or any cleanig product containing alcohol because it can damage the cabinet.
• Before using the appliance for the first time wash
the interior whith luke warm water and some neutral soap so as to remove the typical smell of a
brand-new product and then dry thoroughly.
• Do not use detergents or abrasive powders as
these will damage the finish.
• Remove security used for transportation.
EElleeccttrriiccaall ccoonnnneeccttiioonn
Before plugging the appliance into a socket make
sure that the voltage and frequency shown on the
rating plate correspond to your home supply.
It is essential that the appliance be connected to
an efficient earth tap.
For this purpose the supply cable plug incorporates a special earth contact. If the sockets of your
domestic wiring system are not grounded, have
the appliance connected to a separate ground
wire in accordance with existing safety regulations.
«THE MANUFACTURER DECLINES TO
ACCEPT ANY LIABILITY IF THIS SAFETY RULE
IS NOT OBSERVED».
SSttaarrttiinngg –– uupp
• Plug the appliance into the wall socket.
• Make sure the inner light «H» iluminates when
opening de door.
• Turn the temperature Knob «A» to intermediate
position. Fig. 6.
Fig. 2
Fig. 1
4
Changing the opening direction
of doors and Panelling
Fig. 3
CChhaannggiinngg tthhee ooppeenniinngg ddiirreeccttiioonn ooff tthhee
ddoooorrss
If you wish to change the opening side of the doors
proceed as follows:
1... Remove the handles of the doors, if they are
side fixing by screws.
2... Take off the plinth pressed on to.
3... Remove the inferior hing taking care for the dow-
ner door not to fall off. hinges. Using a 10mm
spanner, unscrew the hinge pin and reassemble
it on the opposite side.
4... Lift the downer door off the central hinge.
5... Remove the central hinge taking care for the
upper door not to fall off and not to lose the plastic spacer.
6... Take the upper door off the upper hinge. Be
careful not to lose the plastic ring.
7... Unscrew the plastic bolts of the opposite side of
the place of the central hinge taken out and introduce them in the holes occupied before by the
hinge.
Fig. 5
C
5
Changing the opening direction
of doors and Panelling
If you refrigerator has top panel, you can manage in
the same way from point 1 to point 6 and then:
7... Unscrew the axle of the upper hing (9 Fig. 5) and
replace it at the opposite side (10 Fig. 5).
8... Remove the lettle lid put on the opposite side of
the central hinge and use it to cover the new
holes left where the hinge was placed.
For the remaining parts proceed the other way
round.
Once finished make sure that all joints close
perfectly well all around the door and chek that
the internal light turns of when the fridge door
closes.
HHooww ttoo ppaanneell tthhee ddoooorrss
If your appliance is provided with metal strips for
panelling and you wish to do so proceed as follows:
1... Remove one of the side strips.
2... Loosen the screws of the remaining strips.
3... Start putting on the panel where you took off the
strip pushing it right up to the end.
4... Replace the strip on this side.
5... Tighten all screws
NOTE:
The panel dimensions must be 2 mm.
shorter than the doors. Maximun thickness of the
panel is 4 mm.
Fig. 5
Loading...