Page 1
English
Warnings - Built-under ovens
It is most important that the instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can be acquainted with the functioning of the appliance and the
relevant warnings. These warnings are provided in the interest of safety. You must read
them carefully before installing or using the appliance.
Installation
Any installation work must be undertaken
by a qualified electrician or competent
person.
Installation and initial adjustment of your
oven MUST be carried out by qualified
personnel in compliance with current
regulations. Specific installation
instructions for the installer are given in this
booklet.
During use
This appliance has been designed for
cooking edible foodstuffs only, and must
not be used for any other purposes.
Always stand back from the oven when
opening the oven door during cooking or
at the end of it to allow any build up of
steam or heat to release.
It is dangerous to alter the specifications
or modify the product in any way.
Appliances become very hot with use, and
retain their heat for a long period after use.
Care should be taken to avoid touching
heating elements inside the oven.
Always ensure that the control knobs are
in the “off” position when not in use.
The use of a gas cooking appliance
results in the production of heat and
moisture in the room in which it is
installed. Ensure that the kitchen is well
ventilated: keep natural ventilation holes
open or install a mechanical ventilation
device (mechanical extractor hood).
Prolonged intensive use of the appliance
may call for additional ventilation, for
example opening of a window, or more
effective ventilation, for example
increasing the level of mechanical
ventilation where present
For hygiene and safety reasons, this
appliance should be kept clean at all times.
A build-up of fats or foodstuffs could result
in a fire.
Never line any part of the oven with
aluminium foil.
Never use steam or steam machines to
clean the appliance.
Before any maintenance or cleaning work
is carried out on the appliance, always turn
off the isolator switch at the cooker point,
and allow to cool.
Ensure that the shelves are put in place in
the correct way.
This oven (even if it is linked to an electrical
cooking table) is made to function at 230 V
monophase with neutral.
Child safety
This appliance is designed to be operated
by adults. Children should not be allowed
to tamper with the controls or play with the
product.
Children should be supervised at all times
and should not be allowed to touch the hot
surfaces or be in the vicinity when in use or
until the appliance has cooled after use.
During oven cooking and grilling, the
appliance door and the surrounding parts
are warmed up to a very high temperature.
Be careful and keep children away from
the appliance while you are using it. When
you connect other appliances to a plug near
the oven, check carefully that the wire does
not touch warm parts of the oven and does
not get taken in the oven door.
.
31
Page 2
Technical assistance
This appliance should be serviced by an
authorized Network Service Centre, and
only genuine spare parts should be used.
Under no circumstances should you
attempt to repair the appliance yourself.
Repairs carried out by inexperienced
persons may cause injury or serious
malfunctioning. Refer to your local Service
Centre. Always insist on genuine spare
parts.
Guide to Use the
instructions
Safety Instructions
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where
you purchased the product.
Step by step instructions for an
operation
Hints and Tips
MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna, 298
47100 FORLÌ (Italy)
When the oven is first installed
The oven will work only if the time
of day has been set (please read
the relevant instructions).
Once the oven has been installed:
a) set the thermostat knob to “MAX”;
b) switch the oven function control knob to
conventional cooking ( );
c) allow the oven to run empty for
approximately 45 minutes;
d) open a window for ventilation.
During this time, an unpleasant odour may
be emitted. This is absolutely normal, and
is caused by residues of manufacturing.
Repeat this operation for the grill and fan
cooking function.
Once this operation is carried out, let the
oven cool down, then clean the oven cavity
with a soft cloth soaked in warm soapy
water.
32
Fig. 1
To open the oven door, always
catch the handle in its central
part.
Before cooking for the first time,
carefully wash the oven accessories.
Page 3
Description of the appliance
823459
7
1
610
11
12
13
14
1. Control panel
2. Control knob for right rear burner
3. Control knob for right front burner
4. Control knob for left front burner
5. Control knob for left rear burner
6. Oven Thermostat control knob
7. Oven Function control knob
8. Operating control light
9. Oven thermostat control light
10. Electronic programmer
11. Grill
12. Oven lamp
13. Oven Fan
14. Rating plate
33
Page 4
Gas Hob
Hob Burner Control Knobs
The hob burners control knobs are situated
on the front panel (Fig. 2). The symbols on
the knobs mean that:
there is no gas supply
there is maximum gas supply
there is minimum gas supply
Lighting the Burners
For easier lighting, proceed before
putting a pan on the pan support.
Push in the relevant knob and turn it
anticlockwise to "maximum position".
After lighting the flame, keep the knob
pushed down for about 5 seconds.
This will allow the "thermocouple"
(Fig. 3, lett. D) to be heated and the
safety device to be switched off,
otherwise the gas supply would be
interrupted.
Then, check the flame is regular and
adjust it as required.
If you cannot light the flame even after
several attempts, check the "cap"
and "crown" (Fig. 3, lett. A-B) is in the
correct position.
To put the flame out, turn the knob to
the symbol "".
Fig. 2
Fig. 3
FO 0204
A - Burner cap
B - Burner crown
C - Ignition candle
D - Thermocouple
Always turn the flame down or put it
out before taking the pans off the
burner.
34
Page 5
Using the hob correctly
To ensure maximum burner efficiency, it is
strongly recommended that you use only
pots and pans with a bottom fitting the size
of the burner used, so that flame will not
spread beyond the bottom of the vessel (see
table below).
Burner
Rapid Burner 180 mm 260 mm
Semirapid Burner 120 mm 220 mm
Auxiliary Burner 80 mm 160 mm
It is also advisable, as soon as a liquid starts
boiling, to turn down the flame so that it will
barely keep the liquid simmering.
Use only pans or pots with flat
bottom.
Carefully supervise cookings with fats
or oil, since these types of foodstuff
can result in a fire, if over-heated.
Minimum Maximum
diameter diameter
35
Page 6
Electric oven
Oven Function (Fig. 4) and
Thermostat (Fig. 5) control
knobs
They enable to select the most appropriate
type of heating for the different cooking
requirements by appropriately connecting
the heating elements and adjusting
temperature to the required level.
0 The oven is OFF.
Oven Light - The oven light will be on
without any cooking function
Conventional cooking - The heat
comes from both the top and bottom
element, ensuring even heating inside
the oven.
Top heating element - The heat comes
from the top of the oven only.
Bottom heating element - The heat
comes from the bottom of the oven
only.
Inner grill element only - can be used
for grilling small quantities.
Double Grill - The full grill element will
be on.
Fan cooking - This allows you to roast
or roast and bake simoultaneously
using any shelf, without flavour
transference.
Defrost Setting - This setting is
intended to assist in thawing of frozen
food.
Fig. 4
Fig. 5
36
Page 7
Operating control light
It indicates that one or more of the heating
elements are turned on.
Oven thermostat control
light
This light goes off when the oven heats up
to the temperature set and comes on again
every time the thermostat cuts in to stabilize
temperature.
Safety thermostat
In order to avoid excessive overheating due
to incorrect use of the appliance or else to a
faulty component, the oven is equipped with
a safety thermostat which cuts off the power
supply if necessary. Operation is restored
automatically when the oven temperature
decreases to normal values. Therefore, if the
thermostat cuts in because you have not
been using the appliance correctly, the oven
can be used again simply by waiting for the
appliance to cool down. If, instead, the
thermostat cuts in because of a faulty
component, you should call the Service
Department.
37
Page 8
Electronic programmer
4
5
6
123
The oven will work only if the time of day has
been set. Moreover, the oven can also be operated
without any programme.
1. Push button for selecting a function
2. Decreasing control button “ ”
7
3. Increasing control button “ ”
8
4. Display
5. “Cooking Duration” pilot lamp
6. “End of cooking” pilot lamp
7. “Minute minder” pilot lamp
8. “Time of day” pilot lamp
Setting the time of day
When the power supply is switched on, or after a power
failure, the “Time of day” pilot lamp will flash on the
display.
To set the correct time of day:
1. press button “ ” or “ ”.
2. After the setting is carried out, wait for 5 seconds: the
“Time of day” pilot lamp will go out and the display
will show the set time. The appliance is ready for use.
To reset the correct time of day:
1. press button repeatedly to select the “Time of day”
function. The relevant pilot lamp will start flashing. Then
proceed as described above.
The time of day may be reset only if no automatic
function (cook duration or end of cooking )
has been set.
“Cooking Duration” function
Thanks to this function, the oven will automatically switch
off at the end of a programmed cooking duration time.
Place food in the oven, select a cooking function and
adjust the cooking temperature. Press button repeatedly
to select the “Cooking Duration” function. The relevant pilot
38
Page 9
lamp will start flashing. Then, proceed as follows:
To set the duration time:
1. press button “ ” or “ ”.
2. After the setting is carried out, wait for 5 seconds:
the "Cooking Duration" pilot lamp will come on
and the display will revert to the time of day.
3. When cooking time is over, the oven will be switched
off automatically and an acoustic alarm will be heard,
while the pilot lamp will start flashing. Turn the oven
function and the thermostat control knob to zero.
To switch off the acoustic alarm, press any button.
NOTE: when doing this operation, the oven will be
operated again, therefore, remember to turn the oven
function and the thermostat control knob to zero at
the end of the cooking time.
To cancel the duration time:
1. Press button repeatedly to select the “Cooking
Duration” function. The relevant pilot lamp will flash
and the display will show the remaining cooking time.
2. Press button “ ” until the display shows “0:00”. After
5 seconds the pilot lamp will go out and the display
will revert to the time of day.
“End of cooking” function
Thanks to this function, you can set the oven to switch off
automatically when a programmed end of cooking time is
over. Place food in the oven, select a cooking function and
adjust the cooking temperature. Press button
repeatedly to select the “End of cooking” function. The
relevant pilot lamp will start flashing. Then, proceed as
follows:
To set the End of cooking time:
1. press button “ ” or “ ”.
2. After the setting is carried out, wait for 5 seconds:
the “End of cooking” pilot lamp will come on and
the display will revert to the time of day.
3. When cooking time is over, the oven will be switched
off automatically and an acoustic alarm will be heard,
while the pilot lamp will start flashing. Turn the oven
function and the thermostat control knob to zero.
To switch off the acoustic alarm, press any button.
NOTE: when doing this operation, the oven will be
operated again, therefore, remember to turn the oven
function and the thermostat control knob to zero when
cooking is over.
39
Page 10
To cancel the End of cooking time:
1. Press button repeatedly to select the “End of cooking”
function. The relevant pilot lamp will flash and the
display will show the programmed End of cooking time.
2. Press button “ ” until the display shows the current
time of day. The programmer will beep and the pilot lamp
will go out.
“Cooking duration” and “End of
cooking time”
The functions “Cooking duration” e “End of cooking time” can
be used simultaneously to set the oven to switch on and off
automatically at a later time.
1. With the “Cooking duration” function (carry out the
cooking duration setting as described in the relevant
chapter) set the duration time. Then, press button :
the display will show the programmed setting.
2. With the “End of cooking time” function (carry out
the End of cooking setting as described in the relevant
chapter) set the end of cooking time.
The relevant pilot lamps will come on and the display
will show the time of day. The oven will switch on and
off according to the set programmes.
combined
“Minute minder” function
The minute minder alarm will sound at the end of a timed
period, but THE OVEN WILL REMAIN ON, if it is in use.
To set the minute minder:
1. Press button repeatedly to select the “Minute minder”
function. The relevant pilot lamp will start flashing.
2. Then, press button “ ” or “ ” (maximum: 2 hours, 30
minutes).
3. After the setting is carried out, wait for 5 seconds: the
“Minute minder” pilot lamp will come on.
4. At the end of the timed period, the pilot lamp will start
flashing and acoustic alarm will be heard. To switch off
the acoustic alarm, press any button.
To cancel the minute minder:
1. Press button repeatedly to select the “Minute minder”
function. The relevant pilot lamp will flash and the
display will show the remaining time.
2. Press button “ ” until the display shows “0:00”. After 5
seconds the pilot lamp will go out and the display will
revert to the time of day.
40
Page 11
How to switch off the
display
1. Press two or three programmer push
buttons simoultaneously and keep them
pressed for about 5 seconds. The display
will switch off.
2. To switch on the display, press any
button.
The display can be switched off only
if no other functions have been set.
41
Page 12
Hints and tips for using the oven
Always cook with the oven door
closed.
The oven is supplied with an exclusive system
which produces a natural circulation of air
and the constant recycling of steam.
This system makes it possible to cook in a
steamy environment and keep the dishes soft
inside and crusty outside. Moreover, the
cooking time and energy consumption are
reduced to a minimum. During cooking steam
may be produced which can be released when
opening the oven door. This is absolutely
normal.
However, always stand back from the
oven when opening the oven door during
cooking or at the end of it to allow any
build up of steam or heat to release.
Conventional cooking
Heat comes from the top and from the
bottom, therefore it is preferable to use the
central runners.
If cooking requires more heat from the top
or from the bottom use the top or the bottom
runners.
The possibility of cooking on several shelf
heights means that you can cook several
different dishes at the same time and up to
three tins of biscuits and mini pizzas to be
eaten immediately or subsequently deep
frozen.
Naturally the oven can also be used for
cooking on just one shelf. In this case you
should use the lowest set of runners so that
you can keep an eye on progress more
easily.
In addition, the oven is particularly
recommended for sterilizing preserves,
cooking home-made fruit in syrup, and for
drying mushrooms or fruit.
Grilling
When grilling meat or fish, spread a little oil
on them and always place them on the oven
grid. The shelf level depends on the
thinckness of the food.
Always place the dripping pan at the lowest
level, with some water in it, to avoid smoke
and unpleasant smells.
Fan cooking
The food is cooked by means of preheated
air force blown evenly round the inside of
the oven by a fan set on the rear wall of the
oven itself.
Heat thus reaches all parts of the oven
evenly and fast and this means that you
can simultaneously cook different types of
foods positioned on the various oven shelves
(Fig. 6). Fan cooking ensures rapid
elimination of moisture and the dryer oven
environment stops the different aromas and
flavours from being transmitted from one food
to another.
42
Fan cooking
4
3
2
1
FO 0351
Fig. 6
Page 13
Some hints
For baking cakes
Cakes require a moderate temperature
(normally between 150 and 200 °C). In
addition, the oven must be heated up
beforehand - for about 10 minutes.
The oven door should not be opened before
at least 3/4 of the set cooking time is up.
Normal short pastry dough should be cooked
in a mould or tin for 2/3 of total cooking time
required and then garnished as desired
before being cooked completely.
Clearly, the remaining cooking time depends
on the type of garnish used (jam, fruit, etc.).
Care should be taken to ensure that any
dough and cake mixes are of the right
consistency since an unduly moist mix
lengthens cooking time unnecessarily. The
raw dough or mix should therefore be fairly
difficult to detach from the spoon or beater.
If three shelves are filled with cakes and tarts
simultaneously, it is advisable to slot in an
extra shelf between the two lower shelves
(Fig. 6).
For cooking meat and fish
Meat cooked in the oven should weigh at
least 1 kg to prevent it from becoming too
dry during cooking. Very tender red meat to
be cooked rare, i.e. well cooked on the
outside but extremely juicy inside, requires
high-temperature cooking (200-220 °C).
White meat, poultry and fish instead require
low-temperature cooking (150-175 °C).
The ingredients for the accompanying sauce
or gravy should be put in the baking pan at
the very beginning only when cooking times
are short.
Otherwise they should be added during the
last half hour. A simple way of checking
whether meat is done or not is to press it
with a spoon; if the meat does not yield under
this pressure it means that it is done to a
turn. In the case of roast beef and fillet
steaks, the inside of which should remain
fairly pink in color, cooking times must be
short.
The meat can be cooked in a baking pan or
else directly on the shelf - in this case a
dripping pan must obviously be placed
underneath the shelf to collect the juice.
Should you cook very fat food, place the
meat directly on the grill and the grill over
the dripping pan in order not to dirty the oven.
Once the meat is cooked, it is advisable to
let it rest for at least 15 minutes before
carving so that the juice does not seep out.
To prevent the formation of too much smoke
in the oven during roasting, it is a good idea
to pour a little water into the dripping pan
and—to prevent steam—to add a little bit
more during cooking if the original amount
dries up too much.
Before serving, the various courses can be
kept hot in the oven which should be turned
down to the minimum temperature.
Warning! - Do not attempt to place
objects on the bottom of the oven and
do not cover it with aluminium foil
while cooking, as you can damage
the enamelled surfaces and the food
you are cooking.
Always place pans, heat-resisting
pans and aluminium foils on the oven
shelves.
Cooking times
Cooking times vary according to the type of
food to be cooked, its consistency, and
volume.We suggest that you take particular
note of your first cooking experiments with
the oven, since operating in the same
conditions for the same dishes you will of
course obtain similar results.
Only experience will enable you to make
the appropriate changes to values given on
charts.
43
Page 14
Cooking Tables
Traditional cooking and fan ducted cooking
Traditional
Cooking
TYPE OF DISH
Weight (gr.)
CAKES
Whipped up kneading
Shortbread dough
Butter-milk cheese cake
Apple cake 1 180 2 (1 and 3)* 170 40 ~ 60 In cake mould
Strudel 2 175 2 150 60 ~ 80
Jam-tart 2 175 2 (1 and 3)* 160 30 ~ 40
Fruit cake 1 175 1 160 45 ~ 60 In bread pan
Sponge cake 1 175 2 (1 and 3)* 160 30 ~ 40 In cake mould
Christmas cake 1 170 1 160 40 ~ 60 In cake mould
Plum cake 1 170 1 160 50 ~ 60 In bread pan
Small cakes 2 175 2 (1 and 3)* 160 25 ~ 35 In baking tray
Biscuits 2 160 2 (1 and 3)* 150 20 ~ 30 In baking tray
Meringues 2 100 2 (1 and 3)* 100 90 ~ 120 In baking tray
Buns 2 190 2 (1 and 3)* 180 12 ~ 20 In baking tray
Pastry: Choux 2 200 2 (1 and 3)* 190 15 ~ 25 In baking tray
BREAD AND PIZZA
1000 White bread 1 190 2 180 40 ~ 60 1-2 pieces
500 Rye bread 1 190 1 180 30 ~ 45 In bread pan
500 Bread rolls 2 200 2 (1 and 3)* 175 20 ~ 35 6-8 rolls
250 Pizza 1 210 2 (1 and 3)* 190 15 ~ 30 in baking pan
FLANS
Pasta flan 2 200 2 (1 and 3)* 175 40 ~ 50 in mould
Vegetable flan 2 200 2 (1 and 3)* 175 45 ~ 60 in mould
Quiches 1 200 2 (1 and 3)* 180 35 ~ 45 in mould
Lasagne 2 180 2 160 45 ~ 60 in mould
Cannelloni 2 200 2 175 40 ~ 55 in mould
MEAT
1000 Beef 2 190 2 175 50 ~ 70 On grid
1200 Pork 2 180 2 175 100 ~ 130 On grid
1000 Veal 2 190 2 175 90 ~ 120 On grid
1500
English roast beef
1500 underdone 2 210 2 200 50 ~ 60 On grid
1500 done 2 210 2 200 60 ~ 70 On grid
1500 well done 2 210 2 200 70 ~ 80 On grid
2000 Shoulder of pork 2 180 2 170 120 ~ 150 With rind
1200 Shin of pork 2 180 2 160 100 ~ 120 2 pieces
1200 Lamb 2 190 2 175 110 ~ 130 Leg
1000 Chicken 2 190 2 175 60 ~ 80 Whole
4000 Turkey 2 180 2 160 210 ~ 240 Whole
1500 Duck 2 175 2 160 120 ~ 150 Whole
3000 Goose 2 175 2 160 150 ~ 200 Whole
1200 Rabbit 2 190 2 175 60 ~ 80 Cut in pieces
1500 Hare 2 190 2 175 150 ~ 200 Cut in pieces
800 Pheasant 2 190 2 175 90 ~ 120 Whole
Meat loaf 2 180 2 160 40 ~ 60 in bread pan
FISH
1200 Trout/Sea bream 2 190 2 (1 and 3)* 175 30 ~ 40 3-4 fishes
1500 Tuna fish/Salmon 2 190 2 (1 and 3)* 175 25 ~ 35 4-6 fillets
(*) If you need to cook more than one dish at the same time, we recommend you to place them on the levels
quoted between brackets.
Level
temp.
4
3
°C
2
1
2 170 2 (1 and 3)* 160 45 ~ 60 In cake mould
2 170 2 (1 and 3)* 160 20 ~ 30 In cake mould
1 160 2 150 60 ~ 80 In cake mould
Fan Oven
Level
4
3
2
1
temp.
°C
44
Cooking
time
NOTES
minutes
Page 15
Grilling -
Quantity
TYPE OF DISH
Pieces Weight
Fillet steaks
Beef-steaks 4 600 3 max 10 ~ 12 6 ~ 8
Sausages 8 — 3 max 12 ~ 15 10 ~ 12
Pork chops 4 600 3 max 12 ~ 16 12 ~ 14
Chicken (cut in two) 2 1000 3 max 30 ~ 35 25 ~ 30
Kebabs 4 — 3 max 10 ~ 15 10 ~ 12
Chicken (breast) 4 400 3 max 12 ~ 15 12 ~ 14
Hamburger 6 600 3 max 10 ~ 15 8 ~ 10
Fish (fillets) 4 400 3 max 12 ~ 14 10 ~ 12
Sandwiches 4-6 — 3 max 5 ~ 7 —
Toast 4-6 — 3 max 2~4 2 ~ 3
The oven temperatures are intended as a guide only. It may be necessary to increase or decrease
the temperatures to suit individual preferences and requirements. Cooking times in the tables do
not include pre-heating.
We recommend, especially when cooking cakes, pizza and bread, to pre-heat the oven for about 10
minutes before cooking.
Cooking times in the table do not include pre-heating. We recommend to pre-heat the oven for about
5 minutes before cooking.
4 800 3 max 12 ~ 15 12 ~ 14
Level
Grilling
4
3
2
1
temp.
Cooking time
°C
(minutes)
Upper
side
Lower
side
45
Page 16
Cleaning and Maintenance
Before any cleaning switch the
oven off and let it cool down.
Never use steam or steam
machines to clean the appliance.
Important! Before carrying out
maintenance and cleaning
operations, make sure that your
oven is disconnected from the
mains power supply.
Cleaning must be carried out after the oven
has cooled down. Wash the enamelled parts
with lukewarm water and detergent. Do not
use abrasive products, such as steel wool
pads, acids etc. since these could damage
the various surfaces. Rinse stainless steel
parts with water after use, and dry them with
a soft cloth or chamois leather.
In the case of persistent stains, you can
use normal non-abrasive detergents or
products specific for stainless steel readily
available on the market. Another alternative
is a drop of hot vinegar. When cleaning the
oven door with the glass top cover use just
hot water, taking care to avoid using coarse
cloths or abrasive products.
The hot acids of fruit (e.g. Iemons, stewed
prunes, etc.) leave difficult-to-remove stains
on the enamelled surfaces; this inconvenient
may remove enamel gloss, but, it does not
impair oven operation.
Clean the oven thoroughly after use; in this
way it will be possible to remove cooking
residuals more easily, thus avoiding these
from burning the next time the oven is used.
Oven door cleaning
For a better cleansing of the oven door, you
are suggested to remove it from the appliance
with the following procedure:
- open tho door completely; lift the small
levers placed on the two hinges and turn
the levers towards the inside (Fig. 7).
- Slowly close the oven door, until it
touches the two levers,
- then push it towards the oven and
remove it by pulling it towards the
outside.
- Place the door on a horizontal level.
After cleaning, assemble the door again
by carrying out the procedure described
above backwards. When the two small
levers are placed again on the hinges, the
door will have been accurately fit.
Fig. 7
FO 0452
Models in stainless steel or aluminium:
We recommend to clean the oven door using
only a wet sponge and dry it up after cleaning
with a soft cloth.
Never use steel wool, acids or abrasive
products as they can damage the oven
surface. Clean the oven control panel
following the same precautions.
46
Page 17
Replacing the oven light
Disconnect the appliance from its power
supply point. Push in and unscrew the glass
cap (Fig. 8). Unscrew the light bulb and
replace it with a new heat-proof bulb (300
°C) having the following features: - Operative
tension: 230 V (50 Hz); - Power: 15 W; Fitting: E 14. Reconnect the appliance.
The Hinged Grill
This model is fitted with a hinged grill
element, to enable you to clean the roof of
the oven easily.
Before proceeding ensure the
oven is cool and is isolated from
the electricity supply.
Undo the screws which hold the grill in
place (see Fig. 9). When doing this
operation for the first time, we
recommend using a screwdriver.
Then gently pull the grill downward to
allow access to the oven roof.
Clean the oven roof with a suitable
cleaner and wipe dry before replacing
the hinged grill element.
Gently push up the grill element into
place and firmly screw into place the
holding nuts.
Ensure the grill holding nuts are
firmly in place to avoid the grill
falling down when in use.
Fig. 8
Fig. 9
47
Page 18
What happens if something goes
wrong
If the appliance is not working correctly, please carry out the following checks, before
contacting your local Service Centre.
SYMPTOM
The oven does not come on
The oven temperature light does
not come on
The oven light does not come on
It takes too much time to finish the
dishes, or they are cooked too fast.
SOLUTION
Check that both a cooking function and a tem-
perature have been selected
or
Check the appliance is wired in properly, and
the socket switch or the switch from the
mains supply to the oven are ON.
Turn the thermostat knob on a temperature
or
Turn the oven function control knob on a
function.
Turn the oven function control knob on a
function
or
Buy a new oven light bulb, asking for it to your
local Service Centre and replace it by following
the instruction provided in this booklet.
Refer to the contents of this booklet,
especially to the chapter "Electric oven".
Steam and condensation settle on
the food and the oven cavity.
48
Leave dishes inside the oven no longer than
15-20 minutes after the cooking is completed.
Page 19
Service and Spare Parts
If after the checks listed in the previous
chapter, the appliance still does not work
correctly, contact your local Service
Centre, specifying the type of
malfunctioning, the appliance model (Mod.),
the product number (Prod. No.) and the
serial number (Ser. No.) marked on the
identification plate. This plate is placed on
the front external edge of the oven cavity.
Original spare parts, certified by the product
manufacturer and carrying this symbol, are
only available at
our Service
Centre and
authorized
spare parts
shops.
49
Page 20
Technical Data
Dimension of the oven
recess
Height 593 mm
Width 560 mm
Depth 550 mm
Dimensions of the oven
cavity
Height 335 mm
Width 395 mm
Depth 400 mm
Capacity 53 l
Gas burner ratings (G20 - 25 mbar)
Auxiliary Burner 1000 W
Semi-rapid Burner 1900 W
Rapid Burner 3000 W
Heating element ratings
Bottom heating element 1000 W
This appliance complies with the
following E.E.C. Directives:
- 73/23 - 90/683 (Low Voltage Directive);
- 89/336 (Electromagnetical Compatibility
Directive);
- 90/396 (Gas Directive);
- 93/68 (General Directives)
and subsequent modifications.
Top heating element 800 W
Full Oven (Top+Bottom) 1800 W
Grill heating elements simple 1650 W
double 2450 W
Fan Oven heating element 2000 W
Oven lamp 15 W
Convection fan 30 W
Maximum power rating 2500 W
Voltage tension (50 Hz) 230 V
Gas Category II2HS3B/P
Appliance adjusted for
50
N.G. G20 - 25 mbar
Page 21
Building-in
Safety information for the
installator
• The surround or cabinet into which the oven
will be built must whithstand temperatures
over 75°C. Should the furniture unit not
comply with this requirement, it may be
subject to warping.
• Wood panels may be used as protection
between the burners and the adjacent
walls, provided that the minimum
clearances which are given in the relevant
diagrams are observed.
• The minimum clearance between the
opening for the building-in and the rear
wall must be observed as indicated in the
diagrams.
• The minimum clearance between the gas
hob and the extractor hood should be
observed as indicated in the
manufacturer's instruction of the cooker
hood itself.
• This appliance can be installed near other
furniture units, even if their height exceeds
the appliance's height, provided that a
minimum clearance of 100 mm (Fig. 11)
is observed and that the opposite side of
the appliance meets with a piece of
furniture or another appliance of the same
height (Fig. 11).
• Ensure that small children do not play with
the package materials which have been
removed from the appliance. Plastic bags
may cause damage and small parts may
be swallowed.
FO 2185
FO 2186
mín.
100 min.
Fig. 10
mín.
500 min.
Fig. 11
51
Page 22
820
45
Gas connection
General warnings
• This gas appliance must be installed by
qualified personnel only, according to the
manufacturer's instructions and the rules
in force.
• This appliance is supplied with a gas
connection R 1/2" located on the rear
side (Fig. 12). The gas connection
should be fitted with an easily accessible
control. A gas tap is recommended,
provided that this is fitted on the right or
left hand side, at a proper clearance
from the zone which can be affected by
the heat diffusion from the appliance.
• When positioning the gas connection
pipe, ensure that it is not subject to mechanical stress or it does not come in
contact with hot surfaces.
Important:
Upon completion of the gas installation, check the perfect
sealing of all the connections by
means of soapy water or a proper gas leakage solution. Never
use a flame.
Opening for the gas hob
The opening for the gas hob shall comply
with the dimensions given in the diagrams.
• Calculate the position of the opening
starting from the front side of the furniture
unit (do not consider the unit door).
Start cutting from 10 mm from the front
(tolerance: +/- 3 mm). The opening shall
be obtained starting from the exact centre
of the furniture unit. (Fig. 13 - Fig. 14).
• Use a well-shaped woodsaw or any other
precision tool such as a miller. Upon
completion, seal the opening borders to
avoid humidity to get inside.
600
FO 2187
Opening for the
gas hob
10 mm
Front side
of the
furniture
unit
FO 2188
280 mm from
490
unit
– 2
the centre of furniture
600
FO 2189
500
Fig. 12
Fig. 13
125
– 2
560
Fig. 14
52
Page 23
550
560
597
FO 2191
Recess for the oven
• The opening for the oven must comply
with the dimensions given in the diagram
(Fig. 15).
• If the furniture unit is closed on the rear
side, an additional opening shall be
obtained onto the rear panel to allow the
gas and electrical connections and a
proper ventilation. This opening shall be
at least 200 x 300 mm wide.
Fixing the appliance to the
furniture unit
• The assembly including the built-in oven
and the gas burner support, which have
been fixed together in the factory to avoid
damage during the transport, must be
inserted into the cabinet recess. Once the
assembly is in place, it is possibile to
split the two parts and proceed with the
installation of the gas burner support into
the opening in the worktop (see following
paragraphs).
• When the oven is placed in the cabinet
recess and the gas hob installation has
been carried out, check that the oven is
centred and secure it with the four wood
screws supplied within the accessory kit.
Fig. 15
Fig. 16
• Open the oven door and secure it at the
left and right hand side with the supplied
screws (Fig. 16).
Warning
The electrical connection cable and the gas
connection pipe should not come in contact with hot surfaces or squeezed.
53
Page 24
Gas hob installation
The gas burner support and the relevant
hardware comes as one assembly together
with the built-in oven directly from the
factory, and it is secured onto the upper
panel of the oven to avoid damage during
transport.
Procedure
• Remove the two fixing screws which keep
the gas burner support linked to the builtin oven, and lift the gas burner support
upwards. Loose the screws "A" (Fig. 17)
then pull the two side brackets towards
the left and right hand side, until they
match the borders of the opening in the
worktop (Fig. 17).
Warning - To avoid that the gas
circuit tightness can be
damaged, it is essential that the
burner set is lifted up no more
that 80 mm maximum from its
original position (Fig. 18).
• Before fixing the gas burner support with
the four screws "B", check that the hob
top can be correctly mounted upon the
opening and that the position of the spark
candles and thermocouples matches the
centre of the relevant holes in the hob top.
If necessary, carry out the proper
adjustments to the gas burner support
position.
• Secure the side brackets to the worktop
by means of the four wood screws which
are supplied within the accessory kit (Fig.
17, letter "B"). Then tighten the four
adjustment screws "A".
Important - Before installing the
hob, check the it is essential that
a thorough leak test is carried
out on the connections of the gas
circuit: taps, internal pipes and
burner bodies.
54
B
A
FO 2190
B
A
PE
Fig. 17
Fig. 18
Page 25
• Place the sealing gasket which supplied
with the appliance onto the front, left and
right borders of the opening for the gas
hob, as shown in Fig. 19. Take care that
the edges meet precisely without
overlapping.
• The earth connection between the hob top
and the built-in oven is obtained by means
of the green/yellow wire. Connect the wire
to the connection tab located in the
bottom side of the hob top (marked with
the symbol - Fig. 20).
• Securing the stainless steel hob top:
place the hob top onto the opening and
fix it to the gas burners with two fixing
screws each (Fig. 21 - n. 1)
• Securing the enamelled hob top:
place the hob top onto the opening and
fix it to the gas burners with two fixing
screws and four washers each (Fig. 21 n. 1, 2 and 3).
Do not use electrical screwdrivers for
this operation, to avoid damages to
the hob top or the burner body. Use
a proper cross-tip screwdriver.
• Place the burner crown and burner caps
onto their housing. Place the pan supports
as well.
• Finally, carry out a functionality test.
FO 2570
Fig. 19
Fig. 20
1
2
1 - Screw 3 - Washer
2 - Washer 4 - Burner
3
4
Fig. 21
55
Page 26
Important
When installing the gas hob into a granite
worktop, we recommend to fix the gas burner
support using the four holes "C" in the side
brackets, as shown in Fig. 22.
FO 2202
FO 2203
Fig. 22
56
Page 27
Instructions for the installer
The instructions given below are
designed specifically for a qualified
installer and should aid him or her to
perform all installation, adjustment,
and maintenance operations with
absolute precision and in compliance
with all current legislation and
regulations. We strongly recommend
that all operations for the installation
of your cooker be carryed out by
Qualified Personnel in accordance
with existing rules and regulations.
Electrical connection
Prior to making the electrical connection,
make sure that:
— the protection fuse and the domestic
wiring system are suitable to carry the
total electric load of the oven (see rating
plate);
— your domestic wiring system has an
efficient earth connection in compliance
with rules and laws in force;
— the wall socket or the omnipole switch
used for the electrical connection can
easily be reached after the oven is built
in.
supply cable must in all cases be laid out in
such a way as to ensure that it does not
reach at any given point a temperature 50°C
higher than the ambient temperature.
Suitable power supply cables are the
following types, considering the respective
necessary section of cable: H07 RN-F, H05
RN-F, H05 RR-F, H05 VV-F, H05 V2V2-F
(T90), H05 BB-F.
Terminal block
The oven has an easily accessible terminal
block, which is meant to work with an
electric single-phase rate of 230 V (Fig. 23).
The Manufacturer disclaims any liability
in case these accident-preventing rules
are not observed.
This appliance is delivered without an
electric supply cable. Therefore, you will
have to fit to it to a supply cable with
standard plug, suitable for the total electric
load shown on the rating plate. The plug is
to be inserted into a suitable wall socket. If
you require a direct connection to the electric
network (mains), it will be necessary to fit
between the appliance and the mains an
omnipole switch, with a minimum gap
between contacts of 3 mm, suitable for the
required load and in compliance with rules
in force. The green & yellow ground wire must
not be interrupted by the switch and it should
be 2-3 cm longer than the other cables. The
Fig. 23
57
Page 28
Adaptation to different types of gas
Injector replacement
Remove the pan supports.
Remove the burner's caps and crowns.
With a socket spanner 7 unscrew and
remove the injectors (Fig. 24), and replace
them with the ones required for the type
of gas in use (see the table below).
Reassemble the parts, following the same
procedure backwards.
Replace the rating label (placed near the
gas supply pipe) with the relevant one for
the new type of gas supply. You can find
this label in the package of the injectors
supplied with the appliance.
Should the feeding gas pressure be different
or variable compared with the required
pressure, an appropriate pressure adjuster
must be fitted on the gas supply pipe, in
compliance with the rules in force.
FO 0392
Fig. 24
Gas Burner Injector Nominal Nominal Minimum By-Pass Feeding
Type 1/100 Power Flow Rate Power 1/100 pressure
mm Rate in Rate (mbar)
(kW)
m³/h g/h
(kW)
Natural Auxiliary 65 1,00 0,095 - 0,33
gas Semi-rapid 92 1,90 0,181 - 0,45
adjustable
25
G20 Rapid 112 3,00 0,286 - 0,65
Liquid Auxiliary 50 1,00 - 72 0,33 28
gas Semi-rapid 71 1,90 - 138 0,45 32 30
G30 Rapid 86 2,80 - 203 0,65 40
Natural Auxiliary 71 1,00 0,110 - 0,33
gas Semi-rapid 100 1,90 0,210 - 0,45
adjustable
25
G25.1 Rapid 124 2,90 0,320 - 0,65
58
Page 29
Adjustment of minimum level
To adjust the minimum level of the burners,
proceed as follows:
Light the burner.
Turn the knob on the minimum position.
Remove the knob.
With a thin screwdriver, adjust the by-
pass screw. Depending on the different
types of gas taps, it may be located
inside the tap shaft, or on the tap body
(see Fig. 25).
If changing from natural gas G20/
G25.1 to liquid gas G30, completely
tighten clockwise the screw, until a small
regular flame is obtained.
If changing from liquid gas G30 to
natural gas G20, loose the screw about
one half of a turn, until a small regular
flame is obtained.
If changing from liquid gas G30 to
natural gas G25.1, loose the screw
about three fourth of a turn, until a small
regular flame is obtained.
Finally check the flame does not go out
when quickly turning the knob from the
maximum position to the minimum
position.
Fig. 25
By-pass
screw
59
Page 30
EON6701FXN
0,79 kWh
0,78 kWh
53,0
43 min.
41 min.
1130 cm
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning
and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers,
washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value
of approx. USD 14 billion in more than 150 countries around the world.
²
47
35688-3401 10/04
Grafiche MDM - Forlì
Loading...