user manual
Oven
EOB68000
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information 2
Product description 4
Daily use 5
SAFETY INFORMATION
Before the installation and use, read this
manual carefully:
• For your personal safety and the safety of
your property
• For the respect of the environment
• For the correct operation of the appliance.
Always keep these instructions with the appliance also if you move or sell it.
The manufacturer is not responsible if incorrect installation or use results in damage.
Children and vulnerable people safety
• This appliance can be used by children
aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning use of
the appliance in safe way and understand
the hazards involved. Children shall not
play with the appliance.
• Keep all packaging away from children.
There is the risk of suffocation or physical
injury.
• Keep children and animals away from the
appliance when the door is open or the
appliance is in operation. There is the risk
of injury or other permanent disability.
• If the appliance has Child lock or Key
lock function, use it. It prevents children
and animals from accidental operation of
the appliance.
General safety
• Do not change the specifications of this
appliance. There is the risk of injury and
damage to the appliance.
• Do not let the appliance stay unattended
during operation.
• Switch off the appliance after each use.
Care and cleaning 14
What to do if… 17
Environment concerns 17
Subject to change without notice
Installation
• Only an approved electrician can install
and connect the appliance. Contact an
approved service centre. This is to prevent the risks of structural damage or
physical injury.
• Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance. If necessary,
contact the supplier.
• Remove all packaging, stickers and layers from the appliance before first use.
Do not remove the rating plate. It can invalidate the guarantee.
• Make sure that the appliance is disconnected from the power supply during the
installation.
• Be careful when you move the appliance.
The appliance is heavy. Always use safety gloves. Do not lift the appliance by the
handle.
• The electrical installation must have an isolation device which lets you disconnect
the appliance from the mains at all poles.
The isolation device must have a contact
opening width of minimum 3 mm.
•You must have correct isolation devices:
line protecting cut-outs, fuses (screw
type fuses removed from the holder),
earth leakage trips and contactors.
• Before the installation, make sure that the
kitchen cabinet has the recess dimensions applicable.
• Make sure that the appliance is installed
below and adjacent safe structures.
• Keep the minimum distances to the other
appliances and units.
• The appliance cannot be positioned on a
base.
• Built in ovens and built in cooking surfaces are attached with special connection
electrolux 3
system. To prevent damage to the appliance, only use an appliance with the appliances from the same manufacturer.
Electrical connection
• The appliance must be earthed.
• Make sure that the electrical data on the
rating plate agree with your domestic power supply.
• Information on the voltage is on the rating
plate.
• Always use a correctly installed shockproof socket.
• Do not use multi-way plugs, connectors
and extension cables. There is the risk of
fire.
• Do not replace or change the mains cable. Contact the service centre.
• Make sure not to squash or cause damage to the mains plug (if applicable) and
cable behind the appliance.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug
– if applicable.
Use
• The appliance is only for domestic use.
Do not use the appliance for commercial
and industrial use.
• Only use the appliance for domestic cooking tasks. This is to prevent physical injury to persons or prevent damage to
property.
• Do not use the appliance as a work surface or storage surface.
• The interior of the appliance and the accessories become hot during use. There
is the risk of burns. Use safety gloves
when you insert or remove the accessories or pots.
• Be careful when you remove or install the
accessories to prevent damage to the
oven enamel.
• Always stay away from the appliance
when you open the door while the appliance is in operation. Hot steam can release. There is the risk of skin burns.
• To prevent damage or discoloration to
the enamel:
– do not put any objects directly on the
appliance floor and do not cover it with
aluminium foil;
– do not put hot water directly into the ap-
pliance;
– do not keep moist dishes and food in
the appliance after you finish the cooking.
• Discoloration of the enamel has no effect
on the performance of the appliance
• Do not apply pressure on the open door.
• Always close the appliance door when
you cook, even while grilling.
Care and cleaning
• Before maintenance, switch off the appliance and disconnect the appliance from
the power supply.
• Before maintenance, make sure that the
appliance is cold. There is the risk of
burns. There is the risk that the glass panels can break.
• Keep the appliance clean at all times. A
build-up of fats or other foodstuff can result in a fire.
• Regular cleaning prevents the surface material from deteriorating
• For your personal safety and the safety of
your property, only clean the appliance
with water and a soap. Do not use flammable products or products that can
cause corrosion.
• Do not clean the appliance with steam
cleaners, high-pressure cleaners, sharp
objects, abrasive cleaning agents, abrasive sponges and stain removers
• If you use an oven spray, follow the instructions from the manufacturer. Do not
spray anything on the fat filter (if applicable), the heating elements and the thermostat sensor.
• Do not clean the glass door with abrasive
cleaning agents or metal scraper. Heat resistant surface of the inner glass can
break and shatter.
• When the door glass panels are damaged they become weak and can break.
You must replace them. Contact the service centre.
• Be careful when you remove the door
from the appliance. The door is heavy!
• Do not clean catalytic enamel (if applicable).
4 electrolux
Risk of fire
• Open the door carefully. The use of ingredients with alcohol can cause a mixture
of alcohol and air. There is the risk of fire.
• Do not let sparks or open flames come
near the appliance when you open the
door.
• Do not put flammable products or items
that are wet with flammable products,
and/or fusible objects (made of plastic or
aluminium) in, near or on the appliance.
Oven lamp
• Disconnect the appliance from the power
supply before the replacement of the
oven lamp. There is the risk of electrical
shock!
PRODUCT DESCRIPTION
5
4
10
3
2
Service centre
• Only an approved engineer can repair or
work on the appliance. Contact an approved service centre.
• Use only original spare parts.
Disposal of the appliance
• To prevent the risk of physical injury or
damage
– Disconnect the appliance from the pow-
er supply.
– Cut off the mains cable and discard it.
– Discard the door catch. This prevents
children or small animals from being
closed inside of the appliance. There is
the risk of suffocation.
1
2
3
4
5
6
7
1
1 Electronic programmer
2 Smell filter
3 Heating element
4 Oven lamp
5 Meat probe socket
6 Side lamp
7 Fan
9
8 Bottom heat
9 Oven shelf runners, removable
10 Shelf positions
Oven accessories
•
Oven shelf
For cookware, cake tins, roasts.
• Flat baking tray
For cakes and biscuits.
8
electrolux 5
•
Deep roasting pan
To bake and roast or as pan to collect fat.
DAILY USE
Warning! Refer to "Safety information"
chapter.
Initial Cleaning
• Remove all parts from the appliance.
• Clean the appliance before first use.
Caution! Do not use abrasive cleaning
agents! This can damage the surface.
Refer to chapter "Care and Cleaning".
Electronic programmer
123
1 Menu option symbol (with oven shelf lev-
el)
2 Clock
3 Heat indicator
Panel sensor fields overview
Sensor
field
To activate and deactivate the appliance.
To show the main menu. The set function deactivates (except for the count-
To move down and up in the menu. When a function is on:
Function Comment
•
Meat probe
To measure how far the meat is cooked.
First Connection
When you connect the appliance to the
mains or after the power cut you have to
set the language, display contrast, display
brightness and time of the day. Touch + or
- to set the value. Touch OK to confirm.
45
4 Temperature / weight
5 Time functions
down timer).
• Touch the sensor field one time: Open the higher menu (function remains on). After 5 seconds
the appliance switches to the initial menu option
• Touch the sensor field two time: Change to the
higher menu and move up and down (the function deactivates)
6 electrolux
Sensor
field
To set the values (example: temperature, time, weight, degree to cook).
,
To set the time functions, more functions and Meat probe.
To confirm.
Function Comment
Touch the sensor fields to operate the
appliance. Make sure, that you only
touch one sensor field. If you apply
your finger too flat, you could touch
more sensor fields.
Symbol
Minute Minder 4:30
Time 10:00
Duration 1:00
End Time
Start 0:45
Temperature
Weight 1,5 kg
Meatprobe 75°C
Heat+Hold 80°C
Smell filter
Display (ex-
amples)
14:50
1.
2.
To operate the value:
• Touch the sensor field one time: The symbol flashes
• Touch the sensor field two time: You can set the
value
To set the values:
• Touch the sensor field one time: To set the value
in slow steps
• Hold down the sensor field: To set the value in
fast steps
To set the display to zero, when you set a cook
time or the time
•
Touch + and - at the same time.
Display symbols
During appliance operation display shows
various symbols.
Function
The countdown timer is on.
The display shows the time set.
Shows the time required for the cooking cycle.
The display shows the time, when the cook time is completed.
The display shows the end time calculated when you inserted the meat probe.
The display shows the time when the appliance starts to
cook. (When you use End Time and Cook Time combined).
1. Indicates temperature level in the cavity. Display
shows it also after you deactivate the appliance and
the cavity is still warm.
2. Rapid heat-up is active. It reduces heat up time.
The display shows that automatic weight system is active
or weight can be changed.
• The meatprobe is installed.
• The Meatprobe Automatic is on.
• You can change the core temperature.
The display shows the function is active.
The smell filter is on.
The menus in overview
Main menu
Sy
mb
ol
Assisted Cooking Contains list of automatic cooking programmes.
Heating Functions Contains list of oven heating functions.
My Programmes
Basic Settings You can use it to set other oven settings.
Menu item Application
Contains list of favourite cooking programmes created by user.
Submenus
Submenus for:
Sym-
bol
Assisted Cooking
Submenu
Pork/Veal
Beef/Game/Lamb
Poultry
Fish
Cake
Pizza/Pie/Bread
Casseroles/Gratins
Convenience
Specials
Submenus for: Heating Functions
Oven function Application
Fan Cooking For baking on up to three oven levels at the same
Conventional Cooking For baking and roasting on one oven level
time. Set the oven temperatures 20-40 °C lower than
when using Conventional.
electrolux 7
Pizza Setting For baking on one oven level dishes that require more
Turbo Grill For roasting larger joints of meat or poultry on one lev-
Economy Grill For grilling flat foodstuffs placed in the middle of the
intensive browning and a crispy base. Set the oven
temperatures 20-40 °C lower than when using conventional.
el. The function is also suitable for gratinating and
browning.
grill and for toasting.
8 electrolux
Oven function Application
Dual Grill For grilling flat foodstuffs in large quantities and for
Bottom Heat For baking cakes with crispy or crusty bases.
Slow Cook For preparing especially tender, succulent roasts.
toasting.
Submenus for: My Programmes
Sym-
bol
- 1 - My Programmes
- 2- My Programmes
- ...
- Edit Programme Name
Submenu
Submenus for: Basic Settings
Sy
mb
ol
Set Time of Day Sets the current time on the clock.
Time Indication
Set+Go
Heat+Hold
Time Extension Activates and deactivates the Time Extension function.
Display Contrast Adjusts display contrast by degrees.
Display Brightness Adjusts display brightness by degrees.
Set Language Sets the language for the display.
Buzzer Volume
Key Tones Activates and deactivates the touch fields tone.
Alarm/Error Tones Activates and deactivates the alarm tones.
Smell Filter Activates and deactivates the smell filter.
Service Shows the software version and configuration.
Factory Settings
Activating and deactivating the
appliance
Touch
to activate or deactivate the appli-
ance.
Submenu Description
When ON, the displays shows the current time when
you deactivate the appliance.
When ON you can choose Set+Go function in the Select Options window.
When ON you can choose Heat+Hold function in the Select Options window.
Adjusts the volume of the touch-tones and signals by
degrees.
Reset all settings to factory settings (including My Programmes ).
Operation of the menus:
1. Activate the appliance.
2.
Touch
or to select the menu op-
tion.
3.
Touch OK to move to submenu or accept setting.
electrolux 9
At every point you can get back to the main
menu with
.
Starting a heating function
1. Select Heating Functions menu. Touch
OK to confirm.
2. Select heating function. Touch OK to
confirm.
3.
Set the temperature. Touch OK to confirm.
Switching off the heating function
Touch
to cancel the procedure.
The display shows the main menu.
Setting the oven temperature
Touch + or - to set the temperature.
The appliance starts to heat.
When the appliance operates at the set
temperature, an acoustic signal sounds.
Showing the oven temperature
Touch + or - at the same time.
The display shows the oven temperature.
Inserting the oven accessories
Put in the slide-in accessories so that the
double side edges are at the back of the
oven and point down to the bottom. Push
the slide-in accessories between the guidebars of one of the oven levels.
The deep roasting pan and the oven
shelf have double side edges. These
edges and the shape of the guide-bars
causes the anti-tilt safety for the oven
accessories.
Inserting the oven shelf and deep
roasting pan together
Put the oven shelf on the deep roasting
pan. Push the deep roasting pan between
the guide-bars of one of the oven levels.
Automatic programmes
These 3 automatic programmes give optimum settings for each type of meat or other recipes:
• Meat programmes with Weight Automatic ( Assisted Cooking menu)
• Meat programmes with Meatprobe Automatic ( Assisted Cooking menu)
• Recipe Automatic ( Assisted Cooking
menu)
Assisted Cooking with Weight
Automatic
This function automatically calculates the
roasting time. To use the function, It is necessary to input the food weight.
Activating the function:
1. Activate the appliance.
2. Select Assisted Cooking . Touch OK to
confirm.
3. Select the category and dish. Touch OK
to confirm.
4. Select the Weight Automatic . Touch
OK to confirm.
5. Touch + or - to set the food weight.
Touch OK to confirm.
The automatic program starts. You can
change the weight at any time. Touch + or
- to change the weight. When time ends,
an acoustic signal sounds. Touch a sensor
field to deactivate the signal.
10 electrolux
With poultry programmes turn over the
food after 30 minutes. The display
shows a reminder.
Assisted Cooking with Recipe
Automatic
This appliance has a set of recipes you can
use. Recipes are fixed and you cannot
change them.
Activating the function:
1. Activate the appliance.
2. Select Assisted Cooking menu. Touch
OK to confirm.
3.
Select the category and dish. Touch OK
to confirm.
4. Select the Recipe Automatic . Touch
OK to confirm.
When you set the option Manual , the
display shows automatic settings but
you can change them.
Assisted Cooking with Meatprobe
Automatic
1. Activate the appliance.
2.
Touch
sisted Cooking , the necessary category
and the dish.
3.
Touch
Meatprobe Automatic .
4. Touch OK to confirm.
The display shows „ Meatprobe “.
5. Install the meat probe.
When the programme ends, an acoustic
signal sounds.
Use a sensor field to deactivate the
acoustic signal.
6. Remove the meat probe.
Meatprobe
Meat probe measures the core temperature
of the meat. When the meat reaches set temperature the oven deactivates automatically.
There are two temperatures to be set
• The oven temperature
• The core temperature
Important! Only use the meat probe
supplied or genuine replacement parts.
1. Activate the appliance.
2. Put the tip of the meat probe into the
centre of the meat.
or to set the function As-
or to set the function
2
1
3. Put the plug of the meat probe into the
socket on the side wall of the oven.
The display shows Meatprobe .
4. Touch + or - in less than 5 seconds to
set the core temperature.
5. Set the oven function and, if necessary,
the oven temperature.
The appliance calculates the provisional
end time for the set temperature (at
least 120°C) again and again. This procedure can take approximately 30 minutes. The display constantly shows the
new provisional end time.
The meatprobe must stay in the meat
and in the meatprobe socket during the
cooking process.
6. When the meat reaches set core temperature, an acoustic signal sounds. The appliance deactivates automatically.
Use a sensor field to stop the signal.
7. Remove the meatprobe plug from the
socket and remove the meat from the
oven.
Warning! The meat probe is hot! There
is the risk of burns! Be careful when
you remove the tip and plug of the
meat probe.
8. Switch off the appliance.
For meat programmes with the meatprobe , refer to automatic programmes .
The core temperature is displayed from
30°C.
My Programmes menu
You can store your favourite settings like duration, temperature or oven function. They
are available in My Programmes menu. You
can store 20 programmes.
electrolux 11
Storing a programme
1. Activate the appliance.
2. Select the oven function or Assisted
Cooking function.
3.
Touch
again and again until the
display shows " SAVE ". Touch OK to
confirm.
4. The display shows the first free memory
position.
Touch OK to confirm.
5. The first letter flashes.
Touch + or - to change the letter.
Touch OK to confirm.
6.
Touch
or to move the cursor to
the right or to the left. Touch OK to confirm.
The letter flashes.
Touch and hold OK to save.
You can overwrite a memory position in
storage. (Refer to the section „Storing a
programme“. At step 4 touch
to choose memory position you
want to overwrite.)
You can change the name of a Programme in the menu ” Edit Programme
Name ”.
Activating the programme
1. Activate the appliance.
2. Select My Programmes menu. Touch
OK to confirm.
3. Select your favourite programme name.
Touch OK to confirm.
7. Repeat steps 5 and 6 again to write
name of the program.
Clock functions
Symbol Function Description
Minute Minder
Duration
End Time
You can use Duration and End Time at
the same time, if the appliance is to activated and deactivated automatically
later.
If you set the time for a clock function, the
time starts to count down after 5 seconds.
If you use the clock functions Duration
and End Time , the appliance deactivates the heating elements after 90 %
of the set time. The appliance uses the
residual heat to continue the cooking
process until the time ends (3-20 minutes).
Setting the clock functions
1.
Touch
again and again until the
display shows the necessary clock function and the related symbol.
2. Touch + or - to set the necessary time.
Touch OK to confirm.
After 90 % of the set time, an acoustic
signal sounds. The appliance deactivates. The display shows a message.
To set a countdown (max 2 hours 30 minutes). This function
has no effect on the operation of the appliance.
To set how long the appliance has to be in operation (max. 23 h
59 min).
To set the switch-off time for an oven function (max. 23 h 59 min).
3. Touch a sensor field to stop the signals.
With Minute Minder you must activate
the appliance to set the clock function.
With Duration and End Time the appliance deactivates automatically.
With Duration and End Time you must
set the heating function and the temperature first. Then you can set the clock
function.
When you use Food Probe, Duration
and End Time do not work.
Time Extension
The Time Extension makes the oven function continue after the set time ends.
• Applicable for all oven functions with Duration or Weight Automatic .
• Not applicable for oven functions with
Meatprobe .
Activating the function:
1. When the cooking time ends, an acous-
tic signal sounds. Touch any sensor field.
or
12 electrolux
2. The display shows the message for
Time Extension for five minutes.
3.
Touch
4.
Set Time Extension period. Touch OK
to activate.
to confirm.
SET+GO
SET+GO function lets you set an oven function (or programme) and use it later with
one touch of the sensor field.
Activating the function:
1. Activate the appliance.
2. Set the heating function.
3.
Touch
again and again until the
display shows Duration .
4. Set the time.
5.
Touch
again and again until the
display shows SET+GO .
6.
Touch OK to confirm.
To start SET+GO touch any sensor field (ex-
). The set oven function starts.
cept
When the oven function ends, an acoustic
signal sounds.
When the oven function operates, the
function Key Lock is on.
You can activate and deactivate the SET
+GO function in the Basic Settings
menu.
Heat+Hold
The Heat+Hold function keeps prepared
food warm at 80° for 30 minutes. It activates after the baking or roasting procedure
ends.
Conditions for the function:
• The set temperature is more than
80°C.
• The function duration is set.
Activating the function
1. Activate the appliance.
2. Select the oven function.
3. Set the temperature above 80°C.
4.
Touch
again and again until the
display shows Heat+Hold . Touch OK
to confirm.
When the function ends, an acoustic signal
sounds.
The Heat+Hold function operates for 30 minutes.
The Heat+Hold function stays on if you
change the oven functions.
You can activate or deactivate the function in Basic Settings menu.
Smell Filter
The Smell Filter minimizes the smells of cooking. You can activate or deactivate it in the
Basic Settings menu.
Once you activate the Smell Filter , it
switches on automatically when you start a
baking or roasting programme (except for
Specials ). Energy consumption increases
when the Smell Filter is activated.
If you deactivate the Smell Filter , it
switches on automatically after 100 hours
of work, in order to clean itself.
Key Lock
The Key Lock prevents an accidental
change of the oven function .
Activating the Key Lock
1. Activate the appliance.
2. Set the oven function.
3.
Touch
again and again until the
display shows Key Lock
4. Touch OK to confirm.
The Key Lock is active.
Deactivating the Key Lock
1.
Touch
.
2. Touch OK to confirm.
The Key Lock is not active.
If you deactivate the appliance, the Key
Lock deactivates.
Child Lock
The Child Lock prevents an accidental operation of the appliance .
Activating the Child Lock
1. Activate the appliance.
Do not set an oven function.
2.
Press
and - at the same time un-
til the display shows a message.
Deactivating the Child Lock
1. Do the above steps again.
Automatic switch-off
The appliance deactivates after some time:
• if you do not deactivate the appliance;
• if you do not change the oven tempera-
ture.
Oven temperature Switch-off time
30 °C - 120 °C 12.5 h
Oven temperature Switch-off time
120 °C - 200 °C 8.5 h
200 °C - 250 °C 5.5 h
250 °C - max °C 3.0 h
To operate the appliance after an automatic
switch-off, touch OK .
Heat-up indicator
When you activate an oven function, the
bar on the display comes on. The bar
shows that the temperature increases.
Rapid heat-up indicator
For some oven functions the rapid heat-up
function decreases the heat-up time automatically. The bar of the indicator moves
from right to left until the oven reaches the
target temperature.
Residual heat indicator
When you deactivate the appliance, the display shows the residual heat. You can use
the heat to keep the food warm.
Cooling fan
When the appliance operates, the cooling
fan switches on automatically to keep the
surfaces of the appliance cool. If you switch
off the appliance, the cooling fan continues
to operate until the appliance cools down.
Safety thermostat
To prevent dangerous overheating (due to
incorrect use of the appliance or defective
components), the oven has a safety thermostat, which interrupts the power supply. The
oven switches back on again automatically,
when the temperature drops.
Mechanical door lock
When the appliance is delivered, the door
lock is deactivated.
Activating and Deactivating the door
lock
1. Take hold of the door trim (B) on the upper edge of the door at both sides and
press inwards to release the clip seal.
Then remove the door trim by pulling it
upwards.
electrolux 13
2
B
1
2. For activating, step a. For Deactivating
step b.
a) Activate Doorlock: Remove lever
(1), move it 4 mm to the left (2) and reinsert (3).
2
3
1
b) Deactivate Doorlock:
Demount lever: Remove lever (1).
1
Remove trim (2) from the under side
of the door trim (B) and push in (3).
3
2
3. Take hold of the door trim (B) at each
side, position it on the inside edge of the
door and plug the door trim (B) into the
upper edge of the door.
14 electrolux
B
Important! There is a guide bar (C) on the
open side of the door trim (B). This must be
pushed between the outer door panel and
the guide corner (D). The clip seal (E) must
be snapped in.
C
D
To open the oven door.
1. Keep lever pressed.
2. Open the door.
To close the oven door
Close door without pressing the lever.
To deactivate door lock
To deactivate the door lock, the lever is
moved to the right again. Proceed as described above.
Important! Switching off the appliance
does not remove the mechanical door lock.
E
CARE AND CLEANING
Warning! Refer to "Safety information"
chapter.
• Clean the front of the appliance with a
soft cloth with warm water and cleaning
agent.
• To clean metal surfaces use a usual cleaning agent
• Clean the oven interior after each use.
Thus you can remove dirt more easily
and it does not burn on.
• Clean stubborn dirt with a special oven
cleaner.
• Clean all oven accessories (with a soft
cloth with warm water and cleaning
agent) after each use and let them dry.
• If you have nonstick accessories, do not
clean them using an aggressive agents,
sharp edged objects or dishwasher. It
can destroy nonstick coating!
Shelf Support Rails
Removing the shelf support rails
1. Pull the front of the shelf support rail
away from the side wall.
2. Pull the rear shelf support rail away from
the side wall and remove it.
2
1
Installing the shelf support rails
Install the shelf support rails in opposite sequence.
The rounded ends of the shelf support
rails must point to the front!
Replacing the oven light bulb/cleaning
the glass cover
Warning! Be careful! There is the risk
of electrical shock!
1. Turn the glass cover anti-clockwise to remove it.
2. Clean the glass cover.
3. Replace the oven light bulb with applicable 300°C heat-resistant oven light bulb.
New oven light bulb must have the
same parameters as your previous one.
4. Install the glass cover.
Replacing the oven lamp (left side of the
appliance) Cleaning the glass cover
1. Remove the left shelf support rail.
2. Use a cross-tip screwdriver to remove
the glass cover.
electrolux 15
3. Use a narrow, blunt object (e.g. a teaspoon) to take off the glass cover and
clean it.
4. If necessary: Replace the oven lamp.
Technical data: 300°C, heat resistant.
5. Install the glass cover.
6. Install the left shelf support rail.
Oven Ceiling
You can fold down the heating element on
the oven ceiling to clean the oven ceiling
easily.
Folding down the heating element
1. Remove the shelf support rails.
2. Hold the heating element with the two
hands at the front
3. Pull it forwards against the spring pressure and out along the support on both
sides.
4. The heating element folds down.
The oven ceiling is ready to clean.
16 electrolux
Installing the heating element
1. Install the heating element in opposite sequence.
Important! Install the heating element
correctly on the two sides above the
support on the inner wall of the oven.
2. Insert shelf support rails.
Oven door and glass panels
To clean the oven door remove it.
Caution! Be careful when you remove
the door from the appliance. The door
is heavy!
Removing the oven door
1. Open the oven door as far as it goes.
2. Lift up clamping levers (A) on the two
door hinges fully.
A
A
3. Close the oven door until the first position (angle approx. 45°).
5. Now you can remove the inner glass panels and clean them.
To install the door follow the procedure
in reverse.
Caution! Be careful with the glass, it
can break.
The oven door has 2, 3 or 4 panels of
glass (depends on the model)
Caution! Rough handling, especially
around the edges of the front panel,
can cause the glass to break.
Removing and cleaning the door glasses
1. Hold the door trim (B) on the top edge
of the door at the two sides and push inwards to release the clip seal.
2
B
1
2. Pull the door trim to the front to remove
it.
45°
4. Hold of the oven door with one hand on
each side and pull it away from the oven
at an upwards angle.
Put the oven door with the outer side
down on a soft and level surface to prevent scratches.
3. Hold the door glass panels on their top
edge one by one and pull them upwards out of the guide
4. Clean the door glass panels.
To install panels follow the procedure in
reverse. Insert the smaller panel first,
then the larger.
WHAT TO DO IF…
Warning! Refer to "Safety information"
chapter.
Problem Possible cause Remedy
The oven does not heatupThe oven is switched off Activate the oven
The oven does not heatupThe clock is not set Set the clock
The oven does not heatupThe necessary settings are not set Check the settings
electrolux 17
The oven does not heatupThe switch-on lock is activated Refer to "Switching off the switch-
The oven does not heatupThe fuse in the fuse box is released Check the fuse
The display shows F11 The meat probe plug is not correct-
The oven lamp does not
operate
The display shows an error code that is not in
this list
If you cannot find a solution to the problem
yourself, contact your dealer or the service
centre.
ly installed into the meat probe
socket
The oven lamp is defective Refer to "Replace the oven lamp"
There is an electronic fault • Switch off the appliance with
The necessary data for the service centre is
on the rating plate. The rating plate is on
the front frame of the oven cavity.
on lock"
If the fuse is released more than
one time, contact a qualified electrician
Install the meat probe plug as far
as possible
the house fuse or the safety
switch in the fuse box and
switch it on again
• If the display shows the error
code again, refer to the Customer Care Department
We recommend that you write the data here:
Model (MOD.) .........................................
Product number (PNC) .........................................
Serial number (S.N.) .........................................
ENVIRONMENT CONCERNS
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
18 electrolux
Packaging material
The packaging material is environmentally-friendly and recyclable. Plastic
parts are marked with international ab-
breviations such as PE, PS, etc. Dispose of the packaging material in the
containers provided for this purpose at
your local waste management facility.
electrolux 19
www.electrolux.com/shop
892946163-A-052010
Loading...