Gas-Hob
USER MANUAL
35692-3403
Mod. EHG 30810
MY-TH-SG
1
English
Important Safety Information
These warnings are provided in the interest of safety. You MUST read them carefully before
installing or using the appliance.
About Installation, Cleaning
and Maintenance
• It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations.
• Disconnect the appliance from the electrical supply,
before carrying out any cleaning or maintenance work.
• Ensure a good ventilation around the appliance. A
poor air supply could cause lack of oxygen.
• Ensure that the gas supply complies with the gas type
stated on the identification label, placed near the gas
supply pipe.
• Using a gas cooking appliance will produce heat
and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
• In case of intensive or long time use of the
appliance, make the ventilation more efficient,
by opening a window or increasing the electric
exhaust fan power.
• Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable is
in perfect conditions. Otherwise, contact your dealer
before proceeding with the installation.
• The manufacturer disclaims any responsability
should all the safety measures not be carried out.
• Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
During Operation
• It is most important that this instruction book should
be retained with the appliance for future reference.
Should the appliance be sold or transferred, always
ensure that the book is left with the appliance in order
that the new owner can get to know the functions of the
appliance and the relevant warnings.
• This appliance has been designed for non professional
purpose in private houses only. It is meant to cook
edible foodstuff only and
purposes.
• It is dangerous to alter the specification in any way.
• For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
2
MUST NOT be used for any other
• Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
• Ensure that all control knobs are in the OFF position
when not in use.
• Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables are
not in contact with it and keep them far enough from
the heated parts of this appliance.
• If the appliance is out of order, disconnect it from the
electric supply.
Child Safety
• This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or play
near or with the oven.
• This appliance is not intended for use by children or
other persons whose physical, sensory or mental
capabilities or lack of experience and knowledge
prevents them from using the appliance safely without
supervision or instruction by a responsible person to
ensure that they can use the appliance safely.
• Accessible parts of this appliance may become hot
when it is in use. Children should be
has cooled.
KEPT AWAY until it
Environmental Information
• After installation, please dispose of the packaging with
due regard to safety and the environment.
• When disposing of an old appliance, make it unusable,
by cutting off the cable.
• The symbol
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
These instructions are only for the countries
stated by the symbol printed on the front cover
of this instruction book.
on the product or on its packaging
Contents
Description of the appliance .............................. 3
Instruction for the User ...................................... 3
Cleaning and Maintenance ................................ 4
Guarantee - After Sales Service........................ 5
Technical Data .................................................. 6
Instruction for the Installer ................................. 6
Gas connection ................................................. 7
Electrical Connection ........................................ 8
Adaptation to different
types of gas ....................................................... 9
Building In ........................................................ 10
Possibilities for insertion ................................. 11
European Guarantee
Guide to Use the instructions
The following symbols will be found in the text to
guide you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
)
Hints and Tips
Environmental information
MANUFACTURER:MANUFACTURER:
MANUFACTURER:
MANUFACTURER:MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna, 298
47100 FORLÌ (Italy)
Description of the appliance
1
1 Ultra-Rapid Burner - 4,0 kW
2 Burner Control Knob
2
Instruction for the User
Burner Control Knob
The hob burner control knob is situated on the hob front
panel. The symbols on the knob mean that :
z there is no gas supply
there is maximum gas supply / Ignition setting
there is minimum gas supply
Lighting the burners
For easier lighting, proceed before putting a
pan on the pan support.
1. Push the relevant knob down and turn it anti-clockwise
until it reaches the "maximum" position.
2. After lighting the flame, keep the knob pushed down
for about 5 seconds. This will allow the "thermocouple"
(Fig.1 lett.D)to be heated and the safety device to be
switched off,
otherwise the gas supply would be interrupted.
3. Then, check the flame is regular and adjust it as
required.
3
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1 lett. A) and the
"crown" (Fig. 1 lett. B) are in the correct position.
To put the flame out, turn the knob to the symbol z.
In the absence of electricity, ignition can occur
without the electrical device; in this case approach
the burner with a flame, push the relevant knob
down and turn it anti-clockwise until it reaches the
"maximum" position.
Always turn the flame down or put it out before
taking the pans off the burner.
Carefully supervise cookings with fats or oil, since
these types of foodstuff can result in a fire, if overheated.
Do not keep the control knob pressed for more than
15 seconds.
If the burner does not light even after 15 seconds,
release the control knob, turn it the "off" position
and wait for at least one minute before trying to light
the burner again.
If the burner accidentally goes out, turn the control
knob to the "off" position and wait for at least 1
minute before trying to light the burner again.
A
B
Fig. 1
Burner minimum maximum
C
A - Burner cap
B - Burner crown
C - Ignition candle
D - Thermocouple
diameter diameter
D
Energy saving advices
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame will
not spread beyond the bottom of the vessel (see the table
beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
• Use only pans or pots with flat bottom.
Ultra-Rapid 180 mm. 260 mm.
Cleaning and Maintenance
Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
manteinance work.
This appliance cannot be cleaned with steam
or with a steam cleaning machine.
Wash the enamelled components with warm soapy
water. Never use abrasive cleaners
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
Carefully wash the stainless steel components with
water, then wipe them dry with a soft cloth.
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
In models with electric ignition, this feature is obtained
through a ceramic "candle" and a metal electrode (Fig.
1 lett. C). Keep these components well clean, to avoid
difficult lighting, and check that the burner crown holes
(Fig. 1 lett. B) are not obstructed.
The stainless steel can become tarnished if
excessively heated. Therefore prolonged
cooking with potstones, earthenware pans or
cast-iron plates is inadvisable. Also, do not
use aluminium foil to protect the top during
use.
Periodic maintenance
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure
adjuster, if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.
4
Guarantee - After Sales Service
Service and original spare parts
This machine, before leaving the factory, has been
tested and studied by many experts and specialists, in
order to give you the best results.
Any repair work which needs to be carried out should be
done with the utmost care and attention.
For this reason we recommend that for any problem you
contact the dealer who sold it to you, or our nearest
authorized Service Centre, specifying the nature of the
problem, the appliance model (Mod.), the product
number (Prod. No.) and the serial number (Ser. No.)
marked on the identification plate.
Original spareparts, certified by the product
manufacturer and carrying this symbol are only available
at our Service Centre and authorized spareparts shops.
5
Technical Data
Gas Burner Rating
Ultra-Rapid Burner 4,0 kW
3,7 kW (town gas)
Class Appliance 3
Setting Liquid Gas G30/G31 28 - 30 mbar
Gas connection G 1/2"
Electric Supply 220 / 240 V ~ 50 / 60 Hz
- 2006/95 (Low Voltage Directive);
- 89/336
- 90/396 (Gas Appliances)
- 93/68 (General Directives)
and subsequent modifications.
This appliance complies with the following
Directives:
(Electromagnetical Compatibility Directive);
Hob recess dimensions
Length 270 mm.
Width 490 mm.
Instruction for the Installer
• The following instructions about installation and
maintenance must be carried out by qualified
personnel in compliance with the regulation in
force.
• The side walls of the unit in which the hob is
going to be installed, must not exceed the height
of the working top.
• Avoid installing the appliance in the proximity of
inflammable materials (e.g. curtains, tea towels
etc.).
• The appliance must be electrically disconnected
before all interventions. If any electric supply to
the appliance is required to carry out the work,
ensure all the necessary precautions are followed.
THE MANUFACTURER WILL NOT ACCEPT LIABILITY,
SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS
INCORPORATED IN THIS BOOK OR THE REGULATION IN
FORCE BE IGNORED.
6
Gas connection
Choose fixed connections or use a flexible pipe in
stainless steel in compliance with the regulation in force.
If using flexible metallic pipes, be careful they do not
come in contact with mobile parts or they are not
squeezed. Use the same attention when the hob is
combinated with an oven.
IMPORTANT - To ensure a correct operation, a saving
of energy and the long-life of the appliance, the voltage
pressure of the appliance must correspond to the
recommended values.
The adjustable connection is fixed to the comprehensive
ramp by means of a threaded nut G 1/2". Interpose the
sealing between the components as shown in Fig. 4.
Screw the parts without forcing, adjust the connection
in the required direction and tighten everything.
Connection using flexible non
D
metal pipes
When the connection can be easily inspected in its full
extent, there is the chance to use a flexible pipe
according to the rules in force. The flexible pipe must be
tightly fixed using clamps according to the rules in force.
LPG : use the rubber pipe holder «D» (Fig. 4).
Always insert the gasket «B». Then proceed with the gas
connection.
The flexible pipe should be made ready for use in such a
way that:
- nowhere it can reach overtemperature, other than
room temperature, higher than 30°C; if the flexible
pipe, to reach the cock, must run behind the range,
it must be installed as shown in Fig. 4;
- it is no longer than 1500 mm;
- it shows no throttles;
- it is not subject to traction or torsion;
- it doesn't get in touch with cutting edges or corners;
- it can be easily inspected in order to check its
condition.
The control of preservation of the flexible pipe consists
in checking that:
- it doesn't show cracks, cuts, marks of burnings both
on the end parts and on its full extent;
- the material is not hardened, but shows its normal
elasticity;
- the fastening clamps are not rusted;
- expiry term is not due.
If one or more abnormalities are seen, do not repair the
pipe, but replace it.
Fig. 4
FO 0067
A) Ramp with ending nut
B) Seal
C) Adjustable connection
D) Rubber pipe holder for LPG
Important
Once installation is complete, check the perfect
seal of every pipe fitting, using a soapy solution,
never a flame
7
Electrical Connection
The appliance is designed to be connected to 220 / 240
V monophase electricity supply.
The connection must be carried out in compliance with
the laws and regulations in force.
Before the appliance is connected:
1. check that the main fuse and the domestic installation
can support the load (see the rating label);
2. check that the power supply is properly earthed in
compliance with the current rules;
3. check the socket or the double pole switch used for
the electrical connection can be easily reached with
the appliance built in the forniture unit.
The appliance is supplied with a connection cable. This
has to be provided with a proper plug, able to support the
load marked on the identification plate. The plug has to be
fitted in a proper socket.
If connecting the appliance directly to the electric system,
it is necessary that you install a double pole switch
between the appliance and the electricity supply, with a
minimum gap of 3 mm. between the switch contacts and
of a type suitable for the required load in compliance with
the current rules.
The connection cable has to be placed in order that, in
each part, it cannot reach a temperature 90 °.
The brown coloured phase cable (fitted in the terminal
block contact marked with "L") must always be connected
to the network phase.
Fig. 3
Fig. 4
Neutral
Earth (yellow/green)
FO 0257
Replacement of the connection cable
The connection of the connection cable to the
appliance's terminal block is of type "Y". This means
that its replacement requires the specific equipment of
a technician.
In this case, only cable type H05V
used. The cable section must be suitable to the voltage
and the working temperature.
The yellow/green earth wire must be approximately 2 cm
longer than the phase wires (Fig. 3).
To open the terminal block and reach the terminals,
proceed as follows:
1. insert the point of a screwdriver into the visible
protrunding part of the terminal block;
2. exert a light pressure and lift (Fig. 4)
2V2-F T90 must be
Fig. 5
8
Adaptation to different types of gas
Replacing the burner injectors
1. Remove the pan supports.
2. Remove the burner's caps and crowns.
3. With a socket spanner 7 unscrew and remove the
injectors (Fig. 6), and replace them with the ones
required for the type of gas in use (see Table 2).
Town gas
Ultra-rapid burner burners: screw the provided grid filter
assembly "C" (Ø 16) on it.
4. Reassemble the parts, following the same procedure
backwards.
5. Replace the rating label (placed near the gas supply
pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.
Should the feeding gas pressure be different or variable
compared with the required pressure, an appropriate
pressure adjuster must be fitted on the gas supply pipe,
in compliance with the rules in force.
Fig. 6
Town gas
FO 0392
Adjusting the minimum level
To adjust the minimum level of the burners, proceed as
follows:
1. Light the burner.
2. Turn the knob on the minimum position.
3. Remove the knob.
4. With a thin screwdriver, adjust the by-pass screw
(see Fig. 7). If changing from town gas to LPG,
completely tighten clockwise the screw, until a small
regular flame is obtained.
5. Finally check the flame does not go out when quickly
turning the knob from the maximum position to the
minimum position.
This procedure can easily be carried out, anyhow the hob
has been positioned or built in the working top.
Table 2 : injectors
BURNER NORMAL REDUCED NORMAL
POWER POWER POWER
Fig. 7
By-pass screw
Table 1 : BY-pass diameters
Burner Ø By-pass
Ultra-Rapid 56
in 1/100
of mm.
kW kW TOWN GAS LPG G30/G31
inj. 1/100 m
Ultra-Rapid Town gas 3,7 1,2 312 0,706
LPG : 4 98 291 286
3
/h inj. 1/100 g/h - G30 g/h - G31
28-30 mbar
9
Building In
510
Dimensions are given in millimetres
These hobs can be inserted in a built-in kitchen unit
whose depth is between 550 and 600 mm. The hobs
dimensions are shown in Fig. 8.
290
Installation and assembly
These hobs can be installed in a kitchen unit with an
opening for insertion whose dimensions are shown in
Fig. 9.
The edge of the cut out must have a minimum distance
from the rear wall of 55 mm.
If there are side walls, or sides of the furniture unit near
the hob, the cut out edges must have a minimum
distance of 100 mm.
Hanging forniture units or hoods must be placed at 650
mm minimum from the hob.
Carry out the building in of the hob as follows:
1. Put the relevant sealings, supplied with the hob,
on the edges of the cut out, taking care that the
sealings meet without overlapping;
2. place the hob in the cut out, taking care of its centring;
3. fix the hob with the relevant screws (Fig. 10). The
traction of the screws is able to trace the sealing, any
excess of which can then be easily removed.
240
140
650 MIN.
490
550 M
IN
55
270
40÷50
30
591
Fig. 9
If several 30cm hob are to be installed side by side
into the same cut out, an assembly kit including
a support side bracket and supplementary
sealings is available at our After Sales Centres.
The relevant installation instructions are supplied
within the kit package.
10
FO 0199
a) sealing
a
Fig. 10
Possibilities for insertion
Kitchen unit with door
Proper arrangements must be taken in designing the
forniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in
Fig.11.
The panel fitted under the hob should be easily
removable to allow an easy access if a technical
assistance intervention is needed.
Kitchen unit with oven
The hob recess dimensions must comply the indication
given in Fig.9 and must be provided with brackets to
allow a continuous supply of air.
To avoid overhating, the building in should be carried out
as shown in Figs. 12 and 13.
The hob's electric connection and the oven's one must
be carried out separately, both for safety reasons and
to allow the oven to be easily taken off the unit.
Fig. 11 Fig. 12 Fig. 13
FO 2044 FO 2041 FO 2042
a) Removable panel
b) Space possibly useful for
connections
11
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed below for the period specified in the appliance
guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the
appliance guarantee will move with you subject to the following qualifications:-
· The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by
production of a valid purchase document issued by the seller of the appliance.
· The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new
country of residence for this particular model or range of appliances.
· The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another
user.
· The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within
the home, i.e. is not used for commercial purposes.
· The appliance is installed in accordance with all relevant regulations in force within your new country of residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
12
131415
www.electrolux.com.sg
02/08
Grafiche MDM - Forlì
Loading...