AEG RH430LD, RH440LD, RH456LD, RH455LD, RH440LDG User Manual

...
Page 1
Type H20 / 60 821 2693 - 61
T.D. 12/2003
English
miniBar
INSTRUCTION for USE
ABSORPTION-REFRIGERATOR
RH 455 LD RH 456 LD
RH 456 LDE
RH 430 LD RH 438 LD RH 440 LD RH 441 LD RH 448 LD RH 460 LD RH 461 LD RH 468 LD
Page 2
2
1.0 INTRODUCTION 3
2.0 FOR YOUR SAFETY 3
2.1 Warnings and Safety Advice 3
2.2 Coolants 3
3.0 WARRANTY AND 3 CUSTOMER SERVICE
4.0 INSTALLATION 4
4.1 The Purpose of this Manual 4
4.2 Tools/Materials Required 4
4.3 Unpacking 4
4.4 Cleaning 4
4.5 Installation 5
4.6 Securing 6
4.7 Connecting the Device to the 7
Electricity Supply
4.8 Changing the Sliding Hinge 8
4.9 Changing the Doorhang 9
5.0 INSTRUCTION FOR USE 10
5.1 Initial Operation 10
5.2 Temperature Control 10
5.3 Automatic Defrost Function 10
5.4 Leakage Detection 10
5.5 Automatic Door Control (ADC) 11
5.6 Interior Light 12
5.7 Environmental Advice 13
5.8 Disposal 13
5.9 Energy Saving Tips 13
5.10 Declaration 13
5.11 Check List 14
5.12 Technical Data 15
TABLE OF CONTENTS
Model No.
Product No.
Serial No.
These operating instructions should be kept in a safe place. If this device is passed on, please include these operating instructions with it.
Warning
Attention
Information
Environmental Advice
Page 3
INTRODUCTION
You have made an excellent choice by choosing the Dometic miniBar. We are convinced that you will be satisfied with your new appliance in every way. Silent in operation, the miniBar fulfils high quality standards and guarantees an efficient use of resources and energy during its entire working life, i.e. during manufacturing, use and disposal. Please study the installation and operating instructions carefully before attempting to operate the miniBar.
FOR YOUR SAFETY
Warnings and Safety Advice
In the interests of children's safety:
When disposing of the refrigerator, remove all doors and leave the shelves inside. This prevents children from being accidentally trapped or suffocated in the refrigerator.
Never open the cooling unit - it is under high pressure. Never store explosive substances, such as lighter fuel, petrol, ether or
similar products in the miniBar.
The minibar is not suitable for the proper storage of medications. The miniBar must be installed in such a way that accidental contact with
the cooling unit (which heats up when in use) is impossible.
The appliance has to be connected to a properly earthed socket in line
with the relevant valid country regulations.
Servicing must only be carried out by authorised service personnel.
Coolants
Ammonia is used as a coolant. This is a natural compound also used in household cleaning agents (1 litre of Salmiak cleaner contains up to 200g of ammonia - about twice as much as is used in the refrigerator). Sodium chromate is used for corrosion protection (less than 2% of the coolant). If a leak occurs (which can be easily detected due to the unpleasant smell):
Switch the device off (pull mains plug, if applicable); Ventilate room thoroughly. Inform hotel personnel.
For the safety of hotel guests and personnel, it has been established by inspectors that the coolant poses no threat to health.
WARRANTY AND CUSTOMER SERVICE
Warranty arrangements are in accordance with EC Directive 44/1999/CE and the normal conditions applicable for the country concerned.
For warranty or other servicing, please contact our Dometic Service department. Any damage due to improper use is not covered by the warranty. The warranty does not cover any modifications to the appliance or the use of non-original Dometic parts; the warranty does not apply if the installation and operating instructions are not adhered to and no liability shall be entertained. Parts can be ordered throughout Europe from our Dometic Service department. When contacting customer service, please always state model, product, MLC-Code and serial number! You can find this information on the model label inside the device.
3
11..00
22..00
2.1
33..00
2.2
e.g.
Page 4
INSTALLATION
The Purpose of this Manual
The manual shows you how to:
install the miniBar correctly. operate the miniBar correctly. guarantee the miniBar´s correct maintenance and functioning. deal with faults by yourself.
Tools / Materials Required
You will need the following tools for initial operation:
Unpacking
Check during unpacking that the device is defect-free.
Report transport damage to the transport company within 48 hours. Check that the voltage noted on the model label corresponds to the
mains voltage.
Depending on the model, the following parts can be found in the miniBar :
Cleaning
Before operating the miniBar, we recommend you clean it both inside and outside.
Use a soft cloth, lukewarm water and a mild detergent. Following this, wash out the miniBar using clean water and dry
thoroughly.
At annual intervals, remove dust from fridge aggregate using a brush or
soft cloth.
AATTTTEENNTTIIOONN
To prevent material damage:
Do not use soap or detergents which are harsh, coarse or
which contain soda.
Keep the door seal free from oil and grease. The cylinder locks have been lubricated in the factory to be long-lasting.
4
4.1
4.2
4.4
44..00
4.3
mild detergent
2x
Page 5
Installation
5
4.5
1. The refrigerator must be level both directions
2. There sould be 20mm clearance to the wall
3. Ventilation must be provided as shown in alternatives A,B,C or D
4. The ventilation duct must at least measure 105mm x the wt
dth of the refrigerator
5. Only the entire cooling unit must project into the duct as shown
6 Air p
assing through the duct must not be
preheated by any source of heat
7. Ventilation grills, if used, must have openings of at least 200cm² each
Please follow the installation details below carefully. Guarantee is valid for products installed as described only.
IMPORTANT:
200 cm²
20 mm
Where a socket outlet is used for the mains connection lead, the outlet must be freely accessible.
Page 6
6
Securing
RH456LD/E
RH430LD, RH440LD, RH441LD, RH460LD, RH461LD RH436D, RH447D, RH438(L)D, RH448(L)D
The miniBar must be screwed onto the cupboard using the lower hinges.
4.6
1. Tighten screw.
2. Put on cap.
1. Tighten screw.
2. Put on cap.
4.6.1
4.6.2
Page 7
Connecting the Device to the Electricity Supply
The device must be connected to a properly earthed socket in line with
the relevant valid country regulations.
Check prior to initial operation that the voltage
noted on the model label corresponds to the mains voltage. If this is not the case, do not connect the device and contact your dealer!
If the connection cable is damaged it must be replaced by the Customer Service at Dometic, or by respectively qualified personnel, in order to prevent any hazards.
Attention: For GB Only !
Plug connection (for United Kingdom only)
If a 3-pin plug is used, it should be fitted with a 3 amp fuse, with other plug types, the circuit should contain a 5 amp fuse.
Warning - This appliance must be earthed. IMPORTANT
The wires in the mains lead of this appliance are coloured in accordance with the following code:
GREEN and YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead
may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.
1. Connect the GREEN and YELLOW coloured wire to the plug terminal marked letter E or earth symbol or coloured green or green and yellow.
2. Connect the BROWN coloured wire to the plug terminal marked letter L or coloured red.
3. Connect the BLUE coloured wire to the plug terminal marked letter N or coloured black.
Moulded-On Plug Version
The mains lead is fitted with a non-rewirable moulded-on plug con­taining a 3 amp fuse. If the fuse requires replacing at any time, the fuse cover/carrier should be removed using a small screwdriver to level out. The old fuse should be replaced by a 3 amp ASTA approved BS1362 fuse and the fuse cover/carrier must be refitted before the plug is used again.
If the fuse cover-carrier is lost, a replaceement can be obtained from the Dometic service Shops.
The fuse cover/carrier must be of the same colour as that of the coloured insert in the base of the plug. In no circumstances must the plug be used
without a correct fuse cover/carrier fitted. ......
4.7
7
4.7.1
Page 8
If the plug supplied on the mains lead is not suitable for the socket in your home, it should be cut off and disposed of safely, or destroyed, to avoid any possible shock hazard resulting from the plug being inserted into a 13 amp socket elswhere in the use. A suitable replacement plug should then be fitted as given above.
Changing the Sliding Hinge
(
possible with RH430LD, RH438LD, RH440LD, RH441LD, RH448 LD, RH460LD, RH436D, RH447D)
8
4.8
1.
2.
3.
4.
Distance to cupboard door (A)
A
1. When closed, the cupboard door (A) must not lie against the rest of the surrounding cupboard area (distance 1-2mm).
2. There must be a distance of 6-8mm between the cupboard door and the miniBar.
1.
2.
1.
2.
mm
mm
Page 9
9
Changing the Doorhang
( RH436D, RH447D, RH430LD, RH440LD,
RH441LD, RH460LD, RH461LD, RH438LD, RH448LD)
1.
2.
3.
4.
5. 6.
7.
8. 9.
10.
11.
R
12.
13.
R
L
L
4.9
1.
2.
1.
2.
Page 10
10
5.1
5.3
5.4
max.
55..00
5.2
min.
Initial Operation
The device must be plugged into a properly
earthed socket.
The miniBar achieves its operating
temperature after several hours.
INSTRUCTION FOR USE
Temperature Control
The miniBar is fitted with an electronic temperature control. The thermostat control button is situated in the internal containers rear area. (RH455LD, RH456LD/E: the thermostat button is situated in the unrefrigerated compartment).
Automatic Defrost Function
The first defrosting phase commences 39 hours after the initial operation
(5.1) and lasts for two hours.
After this, the device operates for 22 hours at a time, followed by a
defrosting period of 2 hours .
The ice layer must never be removed using force, nor must the defrosting process ever be accelerated using a heater.
The miniBar operates silently !
S
TT
TT
TT
S
Leakage Detection
Air sensor
The electronics carries out a leakage test after every defrosting period ( every 24 hrs) by measuring the temperature at the evaporator by means of a second sensor. If a leakage is detected, the miniBar is shut off by the electronics.
Evaporator sensor
Page 11
Automatic Door Control (ADC)
The following descriptions only apply to devices with ADC.
1. Open the miniBar, check its contents and - if applicable- stock it up again.
2. Close the miniBar.
4. Remove ADC key.
Automatic Door Control (electrical)
When the miniBar is opened, a magnetically operated approximation switch located underneath on the fridge is activated (FIG 1.)
Depending on the connection (opening/closing mechanism), an electric circuit is closed or opened. Accordingly, this is registered and processed at the hotel reception. Note: Electrical rating!
The miniBar´s wiring connection is situated at the rear of the appliance and consists of a 3-pin terminal strip (1).
11
5.5
1.
The red dot has disappeared now.
Using a red dot in the display window (A, point 3), the ADC shows that the miniBar´s door has been opened.
1.
2.
RH456LD/E
All other models
A
A
2.
3. Insert ADC key and turn to the right.
3. Insert ADC key and turn to the left.
5.5.1
1= terminal strip 2= approximation switch A= blue (opening mechanism) B= black (closing mechanism) C= white
FIG.1
Page 12
12
Interior Light
RH456LD /E
Model RH456LD/E is fitted with low voltage lighting.
When the door is opened, the light in the cooling shelf is switched on
via a sensor.
The light in the uncooled storage shelf is switched on manually by
means of a switch integrated into the lamp.
Changing bulbs:
Interior Light (All other models)
When the door is opened, the light in the cooling shelf is switched on
via a sensor.
Changing the LED-board:
5.6.2
To obtain spare electronic boards please contact
your Dometic Service Centre.
1. Pull out the mains plug.
2. Remove the reflector disk.
3. Remove the defective bulb.
4. Insert new bulb.
5.Clip reflector disk back in.
5.6
5.6.1
1. Pull out the mains plug.
2. Remove the reflector disk.
3. Remove defective bulb.
4. Insert new bulb.
5. Clip reflector disk back in.
90°
1.
2.
Page 13
Environmental Advice
miniBars manufactured by Dometic GmbH are free from CFCs / HCFCs and fluorinated hydrocarbons. The cooling unit uses ammonia as the coolant (a natural compound of hydrogen and nitrogen). Cyclopentane, which does not damage the ozone layer, is used as propellant for the insulation made from PU-foam.
Disposal
In order to ensure the re-use of recyclable packaging materials, these must be disposed of using local collection systems. The device itself must be handed over to a disposal company or local council which will guarantee the correct use of recyclable materials and the proper disposal of the rest.
Energy Saving Tips
At an average room temperature of approx. 22°C, it is sufficient to
operate the miniBar with an average thermostat setting.
If possible, always store pre-cooled goods. Do not expose the miniBar to direct sunlight and do not place it close
to a source of heat.
An unobstructed air circulation in the fridge aggregate must be
ensured.
When removing goods, only open the miniBar briefly. Switch on the miniBar approx. 12 hours prior to stocking.
Declaration of conformity
13
5.7
5.8
5.10
5.9
Page 14
Check List
14
5.11
Failure : No cooling (the aggregate at the back of the device is cold).
Possible Cause Self Help Authorised Service
a.) The thermostat is set to 0.
b.) The device plug is not
plugged in.
c.) No voltage in socket.
d.) Defective electronics or
sensor feelers.
e.) Defective heating cartridge.
f.) The device is in its defrosting
phase.
a.) Set temperature control to
middle position.
b.) Plug in device plug.
c.) Check building fuse.
f.) See operating instruction
5.3
d.) Install new
electronics or sensor.
e.) Install new heating
cartridge.
Failure : No cooling (the aggregate is warm).
Possible Cause Self Help Authorised Service
a.) The device is not level.
b.) The device was only
switched on a short while ago.
c.) Defective cooling aggregate.
a.) Level the device using a
spirit level.
b.) Switch on the device and
let it run for 5-6 hours.
c.) Check whether
repair is feasible. If not, exchange device.
Failure : Poor Cooling Performance.
Possible Cause Self Help Authorised Service
a.) The cooling aggregate is not
sufficiently ventilated.
b.) The device is exposed to
direct sunlight.
c.) The fridge door does not
close tightly.
d.) Light permanently on when
door closed.
e.) The fridge was stocked a
short while ago.
a.) Check that the ventilation
grids are not covered. Check that device has been installed properly (installation instruction 4.5).
b.) Follow installation
instruction 4.5.
c.) Check installation is in line
with 4.5.
e.) Check fridge after 5-6
hours for proper cooling function.
c.) Is door magnet there?
Install new door, if required.
d.) Replace lighting sen
sor. Install new door, if required.
Failure : Frost formation in fridge.
Possible Cause Self Help Authorised Service
a.) The fridge door does not
close tightly.
a.) Check installation is in line
with 4.5.
a.) Is door magnet there?
Install new door.
Page 15
15
Technical Data
Built-in Built-in Freestanding / Freestanding
Built-in
Casing Metal Metal Metal Wood
Gross Contentss
(litres) 30 40 40 55
cooled / uncooled 30 / - 40 / - 40 / - 35 / 20
Dimensions (mm)
(H x W xD) 522x384x412 554x401x446 554x401x449 780x420x445
Electrical Rating (W) 65 65 65 65
Power Consumption
kWh / 24h* 0,7 0,8 0,8 0,8
Net Weight (kg) 11 14 15 26
Built-in Freestanding Freestanding / Freestanding /
Built-in Built-in
Casing Metal Metal Metal Metal
Gross Contents
(litres) 56 56 60 60
cooled / uncooled 40 / 16 40 / 16 60 / - 60 / -
Dimensions (mm)
(H x W x D) 658x450x503 721x450x505 563x486x474 563x486x474
Electrical Rating (W) 65 65 80 80
Power Consumption
kWh / 24h* 0,9 0,9 1,0 1,45
Net Weight (kg) 21 24,5 20 23
Freestanding / Freestanding /
Built-in Built-in
Casing Metal Metal
Gross Contents
(litres) 30 40
cooled / uncooled 30 / - 40 / -
Dimensions (mm)
(H x W x D) 522x384x411 554x401x446
Electrical Rating (W) 65 65
Power Consumption
kWh/ 24h* 0,7 0,8
Net Weight (kg) 11 14
* Power consumption measured at an average ambient temperature of 25°C as an average annual value and at a cooling compartment temperature of 7°C in line with DIN/EN153. We reserve the right to make technical modifications to our products without notice!
Model RH430/438LD RH440/448LD RH441LD RH455LD
Model RH456LDE RH456LD RH460LD RH461LD
Model RH436D RH447D
5.12
Page 16
Dometic GmbH
In der Steinwiese 16
D-57074 Siegen
Phone: +49-(0) 271 / 692 0
Fax: +49-(0) 271 / 692 300
www.dometic.de/minibar
www.dometic.com
© Dometic GmbH - 2003 - Subject to change without notice - Printed in Germany
Loading...